Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape memory”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Microwires fabricated by glass-coated melt spinning

The glass-coated melt spinning method offers a route for the manufacture of metal filaments with a few micrometers in diameter in a single operation directly from the melt. Cobalt-based amorphous wires, Cu-15.0 atomic percent (at. %) Sn shape-memory wires, and Ni{sub 2}MnGa (atomic percent) ferromagnetic wires were successfully produced by this method. The cobalt-based amorphous wire is flexible, and Cu-15.0 at. % Sn shape-memory wires have the tensile elongation of 14%. However, because of chemical reaction with glass and oxidation, it is hard to make Cu–Al–Ni shape-memory wires and Ni–Nb–Sn amorphous wires. Conditions for preparing these materials were summarized, and the differences of the solidification processes among glass-coated amorphous cobalt-based wires, Cu-15.0 at. % Sn shape-memory wires, and Ni{sub 2}MnGa wires were analyzed and discussed.

36 MATERIALS SCIENCE↗

Methods, systems, and apparatuses for in-line variably porous surfaces

Variably porous panels and panel assemblies incorporating shape memory alloy components along with methods for actuating the shape memory alloys are disclosed to predictably alter the porosity of a substrate surface, with the shape memory alloy maintained in an orientation relative to the panel that is in-plane with a mold-line of the panel outer surface.

36 MATERIALS SCIENCE↗

Waste Heat Recovery System: Lightweight Thermal Energy Recovery (LIGHTER) System

Broad Funding Opportunity Announcement Project: GM is using shape memory alloys that require as little as a 10°C temperature difference to convert low-grade waste heat into mechanical energy. When a stretched wire made of shape memory alloy is heated, it shrinks back to its pre-stretched length. When the wire cools back down, it becomes more pliable and can revert to its original stretched shape. This expansion and contraction can be used directly as mechanical energy output or used to drive an electric generator. Shape memory alloy heat engines have been around for decades, but the few devices that engineers have built were too complex, required fluid baths, and had insufficient cycle life for practical use. GM is working to create a prototype that is practical for commercial applications and capable of operating with either air- or fluid-based heat sources. GM’s shape memory alloy based heat engine is also designed for use in a variety of non-vehicle applications. For example, it can be used to harvest non-vehicle heat sources, such as domestic and industrial waste heat and natural geothermal heat, and in HVAC systems and generators.

ARPA-E↗

First-principles investigation of phase stability in the Mg-Sc binary alloy

The recent discovery of shape memory behavior in Mg-Sc alloys has opened the door to the possibility of lightweight shape memory alloys. Very little is known, however, about martensitic phase transformations or about equilibrium phase stability in this alloy system. In this paper we report on a first-principles statistical mechanics study of zero Kelvin and finite temperature phase stability of hcp, bcc, and fcc based phases in the Mg-Sc binary. Our calculations reveal a rich array of phase transitions among the different low-temperature ordered and high-temperature disordered phases. Ground state orderings on hcp, bcc, and fcc belong to families of hierarchical structures containing rods of scandium atoms assembled in layers that repeat periodically. Both fcc and bcc are found to undergo a series of second-order phase transformations with increasing temperature until they completely disorder. A high degree of degeneracy is predicted at low and high temperatures among hcp, bcc, and fcc, a property that is likely to play an important role in the shape memory effects observed in this alloy.

36 MATERIALS SCIENCE↗

Temperature and electrical memory of polymer fibers

We report in this work studies of the shape memory behavior of polymer fibers loaded with carbon nanotubes or graphene flakes. These materials exhibit enhanced shape memory properties with the generation of a giant stress upon shape recovery. In addition, they exhibit a surprising temperature memory with a peak of generated stress at a temperature nearly equal to the temperature of programming. This temperature memory is ascribed to the presence of dynamical heterogeneities and to the intrinsic broadness of the glass transition. We present recent experiments related to observables other than mechanical properties. In particular nanocomposite fibers exhibit variations of electrical conductivity with an accurate memory. Indeed, the rate of conductivity variations during temperature changes reaches a well defined maximum at a temperature equal to the temperature of programming. Such materials are promising for future actuators that couple dimensional changes with sensing electronic functionalities.

36 MATERIALS SCIENCE↗

Development and Evaluation of a Novel Curved Biopsy Device for CT-Guided Biopsy of Lesions Unreachable Using Standard Straight Needle Trajectories

PurposeTo evaluate the feasibility of a novel curved CT-guided biopsy needle prototype with shape memory to access otherwise not accessible biopsy targets.Methods and MaterialsA biopsy needle curved by 90° with specific radius was designed. It was manufactured using nitinol to acquire shape memory, encased in a straight guiding trocar to be driven out for access of otherwise inaccessible targets. Fifty CT-guided punctures were conducted in a biopsy phantom and 10 CT-guided punctures in a swine corpse. Biposies from porcine liver and muscle tissue were separately gained using the biopsy device, and histological examination was performed subsequently.ResultsMean time for placement of the trocar and deployment of the inner biopsy needle was ~205 ± 69 and ~93 ± 58 s, respectively, with a mean of ~4.5 ± 1.3 steps to reach adequate biopsy position. Mean distance from the tip of the needle to the target was ~0.7 ± 0.8 mm. CT-guided punctures in the swine corpse took relatively longer and required more biopsy steps (~574 ± 107 and ~380 ± 148 s, 8 ± 2.6 steps). Histology demonstrated appropriate tissue samples in nine out of ten cases (90%).ConclusionsTargets that were otherwise inaccessible via standard straight needle trajectories could be successfully reached with the curved biopsy needle prototype. Shape memory and preformed size with specific radius of the curved needle simplify the target accessibility with a low risk of injuring adjacent structures.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Shape-morphing composites with designed micro-architectures

Shape memory polymers (SMPs) are attractive materials due to their unique mechanical properties, including high deformation capacity and shape recovery. SMPs are easier to process, lightweight, and inexpensive compared to their metallic counterparts, shape memory alloys. However, SMPs are limited to relatively small form factors due to their low recovery stresses. Lightweight, micro-architected composite SMPs may overcome these size limitations and offer the ability to combine functional properties (e.g., electrical conductivity) with shape memory behavior. Fabrication of 3D SMP thermoset structures via traditional manufacturing methods is challenging, especially for designs that are composed of multiple materials within porous microarchitectures designed for specific shape change strategies, e.g. sequential shape recovery. We report thermoset SMP composite inks containing some materials from renewable resources that can be 3D printed into complex, multi-material architectures that exhibit programmable shape changes with temperature and time. Through addition of fiber-based fillers, we demonstrate printing of electrically conductive SMPs where multiple shape states may induce functional changes in a device and that shape changes can be actuated via heating of printed composites. As a result, the ability of SMPs to recover their original shapes will be advantageous for a broad range of applications, including medical, aerospace, and robotic devices.

36 MATERIALS SCIENCE↗

Influence of fatigue on the nanohardness of NiTiCr-wires

Testing parameters, such as rotational speed and bending radius, have a strong influence on the fatigue life of pseudoelastic NiTi shape-memory alloys during bending rotation fatigue (BRF) experiments [M. F. X. Wagner, Int. J. Mat. Res. 97 (2006), p. 1687-1696. and M. Frotscher, et al., Thermomechanical processing, microstructure and bending rotation fatigue of ultra-fine grained NiTiCr-wires, Proceedings of the International Conference for Shape Memory and Superelastic Technologies (SMST 2007), Tsukuba, Japan, ASM International, (2008), p. 149-158.]. Previous studies showed a decrease in the fatigue life for smaller bending radius (i.e. higher equivalent strain) and larger rotational speed. This observation is associated with an increase of dislocation density, the stabilization of stressinduced martensite during cycling, and an increase of the plateau stresses due to self-heating. In the present study, we examine the influence of these fatigue parameters on the nanohardness and shape recovery of pseudoelastic NiTiCr shape-memory alloy wires by nanoindentation. We show that nanoindentation is a suitable method for the characterization of fatigue-related microstructural changes, which affect the mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structure/property relationships in copolymers comprising renewable isosorbide, glucarodilactone, and 2,5-bis(hydroxymethyl)furan subunits

Carbohydrates and their derivatives have great potential as building blocks for the development of renewable materials that are cost and performance competitive with conventional petroleum-based materials. To this end, the rigid carbohydrate-derived diols, glucarodilactone and isosorbide were functionalized with a castor oil derivative, 10-undecenoic acid, forming α,ω-dienes suitable for acyclic diene metathesis (ADMET) polymerization. Equimolar copolymerizations of these two monomers, glucarodilactone undecenoate (GDLU) and isosorbide undecenoate (GDLU), transform brittle homopolymers into elastic materials with shape memory capabilities. To understand the source of these properties, a series of copolymers consisting of a range of GDLU and IU compositions (100:0, 77:23, 76:24, 52:48, 48:52, 18:82, 0:100 mol percent GDLU to IU) was synthesized. The material and chemical properties were characterized by uniaxial tensile testing, small-amplitude oscillatory shear rheology, X-ray scattering and hydrolytic degradation testing. Small compositional changes in this family were shown to have a drastic impact on the observed mechanical performance and degradability of these materials. Rheological measurements of GDLU-containing copolymers found evidence for the presence of transient networking within these materials. We posit that the transient network within this material is responsible for the elasticity and shape memory abilities of the GDL-containing materials. In confirmation of these properties, a novel α,ω-diene 2,5-bis(hydroxymethylfuran) undecenoate (BHMFU) was developed and served as a direct replacement for either GDLU or IU in copolymerizations. The replacement of GDLU resulted in a total loss of the elasticity and shape memory of the copolymers, supporting the role of GDLU in the mechanical performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combinatorial Synthesis and High-Throughput Characterization of Microstructure and Phase Transformation in Ni–Ti–Cu–V Quaternary Thin-Film Library

Ni–Ti–based shape memory alloys (SMAs) have found widespread use in the last 70 years, but improving their functional stability remains a key quest for more robust and advanced applications. Named for their ability to retain their processed shape as a result of a reversible martensitic transformation, SMAs are highly sensitive to compositional variations. Alloying with ternary and quaternary elements to fine-tune the lattice parameters and the thermal hysteresis of an SMA, therefore, becomes a challenge in materials exploration. Combinatorial materials science allows streamlining of the synthesis process and data management from multiple characterization techniques. In this study, a composition spread of Ni–Ti–Cu–V thin-film library was synthesized by magnetron co-sputtering on a thermally oxidized Si wafer. Composition-dependent phase transformation temperature and microstructure were investigated and determined using high-throughput wavelength dispersive spectroscopy, synchrotron X-ray diffraction, and temperature-dependent resistance measurements. Of the 177 compositions in the materials library, 32 were observed to have shape memory effect, of which five had zero or near-zero thermal hysteresis. These compositions provide flexibility in the operating temperature regimes that they can be used in. A phase map for the quaternary system and correlations of functional properties are discussed with respect to the local microstructure and composition of the thin-film library.

42 ENGINEERING↗

Martensitic transformation behaviors of rapidly solidified Ti–Ni–Mo powders

For the fabrication of bulk near-net-shape shape memory alloys and porous metallic biomaterials, consolidation of Ti–Ni–Mo alloy powders is more useful than that of elemental powders of Ti, Ni and Mo. Ti{sub 50}Ni{sub 49.9}Mo{sub 0.1} shape memory alloy powders were prepared by gas atomization, and transformation temperatures and microstructures of those powders were investigated as a function of powder size. XRD analysis showed that the B2–R–B19 martensitic transformation occurred in powders smaller than 150 μm. According to DSC analysis of the as-atomized powders, the B2–R transformation temperature (T{sub R}) of the 25–50 μm powders was 18.4 °C. The T{sub R} decreased with increasing powder size, however, the difference in T{sub R} between 25–50 μm powders and 100–150 μm powders is only 1 °C. Evaluation of powder microstructures was based on SEM examination of the surface and the polished and etched powder cross sections and the typical images of the rapidly solidified powders showed cellular morphology. Porous cylindrical foams of 10 mm diameter and 1.5 mm length were fabricated by spark plasma sintering (SPS) at 800 °C and 5 MPa. Finally these porous TiNi alloy samples are heat-treated for 1 h at 850 °C, and then quenched in ice water. The bulk samples have 23% porosity and 4.6 g/cm{sup 3} density and their T{sub R} is 17.8 °C.

36 MATERIALS SCIENCE↗

Structural state of a radiation-modified Ti{sub 50}Ni{sub 47}Fe{sub 3} single crystal

The structural state of a Ti{sub 50}Ni{sub 47}Fe{sub 3} single crystal irradiated by fast neutrons (F = 2.5 Multiplication-Sign 10{sup 20} cm{sup -2}) at 340 K was studied by thermal neutron diffraction at 78 and 295 K. The melt of this composition was chosen with the purpose of designing a radiation-resistant material exhibiting a shape-memory effect. It was found that the melt remains crystalline after irradiation, whereas the Ti{sub 49}Ni{sub 51} crystal studied earlier becomes amorphous after an analogous irradiation. In spite of the fact that the main structural motif of the crystal remains unchanged after irradiation, martensitic transformations in the crystal do not occur and, consequently, the shape-memory effect is not retained. The radiation resistance of this class of crystals was estimated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural evaluation of NiTi-based films deposited by magnetron sputtering

Shape memory alloy films belonging to the NiTi-based systems were deposited on heated and unheated substrates, by magnetron sputtering in a custom made system, and their structure and composition was analyzed using electron microscopy. Several substrates were used for the depositions: glass, Cu-Zn-Al, Cu-Al-Ni and Ti-NiCu shape memory alloy ribbons and kapton. The composition of the Ti-Ni-Cu films showed limited differences, compared to the one of the target and the microstructure for the DC magnetron sputtering revealed crystallized structure with features determined on peel off samples from a Si wafer. Both inter and transcrystalline fractures were observed and related to the interfacial stress developed on cooling from deposition temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

4D Printing via an Unconventional Fused Deposition Modeling Route to High-Performance Thermosets

An unprecedented four-dimensional (4D) printing process allowing high-performance and shape memory thermoset to be printed, for the first time, by fused deposition modeling (FDM) with isotropic properties has been achieved. Here, bisphenol A-based epoxy and benzoxazine were formulated to a low-temperature thermoplastic and high-temperature thermoset resin, which is melt-extrudable and can be postcured into covalently cross-linked material. Carbon nanotube (CNT) was added in the resin to work as both mechanical enhancement filler and rheology modifier to prevent shape deformation during postcuring process. The cross-layer reaction fuses individual layers into an integrity, thus eliminating layer delamination induced by FDM, offering isotropic mechanical properties regardless of the printing orientations. The highly cross-linked network provides outstanding mechanical strength and superb thermal stability. The excellent shape memory performance with fast recovery rate and large recovery degree is also obtained in the three-dimensional (3D) printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Magnetic-field-induced transformation in FeMnGa alloys

A kind of ferromagnetic shape memory alloy with off-stoichiometric composition of Heusler alloy Fe{sub 2}MnGa has been synthesized. By optimizing composition, the martensitic transformation has been modified to occur at about 163 K accompanying spontaneous magnetization, which enables a magnetic field-induced structural transition from a paramagnetic parent phase to a ferromagnetic martensite with high magnetization of 93.8 emu/g. The material performs a quite large lattice distortion through the transformation, (c-a)/c=33.5%, causing a shape memory strain upto 3.6%. Such large lattice distortions strongly influence the electron structures, and thus some special physical behavior related to the transport and conductive properties is investigated.

36 MATERIALS SCIENCE↗

Enhanced superelasticity of nanocrystalline NiTi/NiTiNbFe laminar composite

This study explores a new concept of the synergy between two constituent shape memory alloys (SMAs) in a composite to achieve a wide superelastic temperature window. In this work, a nanocrystalline NiTi/NiTiNbFe dual-SMA composite is designed, in which two constituent SMAs are both capable of stress-induced martensitic transformation, but within different temperature ranges. Based on the principle of lattice strain matching between the two SMAs, superelastic martensitic transformation in one induces superelastic transformation in the other at temperatures the latter will not when standing alone. Furthermore, via this synergy the composite is able to achieve an ultra-wide superelastic temperature window of 336°C, from -196 to 140°C, with a ~5% tensile strain recovery and high superelastic stresses in the range of 700~1400 MPa. Such properties appear superior to all NiTi-based shape memory alloys to date.

36 MATERIALS SCIENCE↗

Effect of Al substitution on the magnetocaloric properties of Ni-Co-Mn-Sn multifunctional alloys

Ni-Mn-based metamagnetic shape memory alloys have been extensively studied due to their multifunctional properties including magnetocaloric effect (MCE), magnetoresistance effect, and magnetic-field-induced strain. However, the large intrinsic thermal hysteresis of these alloys sets a limit on further development for practical applications. Here, with a few atomic percent Al substitution, we greatly reduced the thermal hysteresis and transformation temperature interval while maintaining the large magnetization difference (ΔM) between austenite and martensite. The simultaneous achievement of a large ΔM and low thermal hysteresis leads to a remarkable enhancement in MCE upon Al substitution, and a maximum magnetic entropy change of 31.6 J/kg K is achieved under a field of 5 T in Ni 39 Co 11 Mn 40 Sn 8 Al 2 . Furthermore, our in situ high-energy X-ray diffraction experiments show that the Ni 39 Co 11 Mn 40 Sn 8 Al 2 has good geometric compatibility between austenite and martensite, which accounts for the reduced thermal hysteresis in this alloy. This study is instructive for the development of high-performance magnetocaloric materials in the metamagnetic shape memory alloys.

36 MATERIALS SCIENCE↗