Search NASA⌕ Search

SEARCH · Search NASA

Results for “speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

High speed imaging - An important industrial tool

High-speed photography, which is a rapid sequence of photographs that allow an event to be analyzed through the stoppage of motion or the production of slow-motion effects, is examined. In high-speed photography 16, 35, and 70 mm film and framing rates between 64-12,000 frames per second are utilized to measure such factors as angles, velocities, failure points, and deflections. The use of dual timing lamps in high-speed photography and the difficulties encountered with exposure and programming the camera and event are discussed. The application of video cameras to the recording of high-speed events is described.

Moore, Alton↗
NASA NTRS1987

Dynamic data acquisition, reduction, and analysis for the identification of high-speed compressor component post-stability characteristics

A compressor test was conducted in which transient data were obtained for the purpose of identifying the high-speed post-stability characteristics. The transient, surge-cycle nature of high-speed post-stability operation precludes the possibility of obtaining the characteristics in a steady-state manner, as is possible during low-speed poststability operation, which is characterized by quasi-steady rotating-stall behavior. Specialized compressor instrumentation was developed and was used to obtain the necessary surge-cycle performance data, which were then digitized, filtered, and analyzed. The high-speed post-stability characteristics were obtained through the use of a maximum likelihood-parameter estimation technique. The estimated characteristics were found to be insensitive to the presence of measurement noise and unmodelled system dynamics, but the compressor time-response constants, which were also estimated, were more sensitive to these same disturbances.

Dvorak, S. D.↗
NASA NTRS1985

Wind-Tunnel Results of Advanced High-Speed Propellers at Takeoff, Climb, and Landing Mach Numbers

Low-speed wind-tunnel performance tests of two advanced propellers have been completed at the NASA Lewis Research Center as part of the NASA Advanced Turboprop Program. The 62.2 cm (24.5 in.) diameter adjustable-pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds (i.e., from Mach 0.10 to 0.34) at zero angle of attack in the NASA Lewis 10 by 10 Foot Supersonic Wind Tunnel. Both models had eight blades and a cruise-design-point operating condition of Mach 0.80, and 10.668 km (35,000 ft) I.S.A. altitude, a 243.8 m/s (800 ft/sec) tip speed, and a high power loading of 301 kW/sq m (37.5 shp/sq ft). Each model had its own integrally designed area-ruled spinner, but used the same specially contoured nacelle. These features reduced blade-section Mach numbers and relieved blade-root choking at the cruise condition. No adverse or unusual low-speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propeller. Typical efficiencies of the straight and 45 deg swept propellers were 50.2 and 54.9 percent, respectively, at a takeoff condition of Mach 0.20 and 53.7 and 59.1 percent, respectively, at a climb condition of Mach 0.34.

Stefko, George L.↗
NASA NTRS1989

High-speed civil transport study. Summary

A system of study of the potential for a high speed commercial transport aircraft addressed technology, economic, and environmental constraints. Market projections indicated a need for fleets of transport with supersonic or greater cruise speeds by the years 2000 to 2005. The associated design requirements called for a vehicle to carry 250 to 300 passengers over a range of 5000 to 6000 nautical miles. The study was initially unconstrained in terms of vehicle characteristics, such as cruise speed, propulsion systems, fuels, or structural materials. Analyses led to a focus on the most promising vehicle concepts. These were concepts that used a kerosene type fuel and cruised at Mach numbers between 2.0 to 3.2. Further systems study identified the impact of environmental constraints (for community noise, sonic boom, and engine emissions) on economic attractiveness and technological needs. Results showed that current technology cannot produce a viable high speed civil transport. Significant advances are needed to take off gross weight and allow for both economic attractiveness and environment acceptability. Specific technological requirements were identified to meet these needs.

Source record↗
NASA NTRS1989

High-speed civil transport study

A system study of the potential for a high-speed commercial transport has addressed technological, economic, and environmental constraints. Market projections indicate a need for fleets of transports with supersonic or greater cruise speeds by the year 2000 to 2005. The associated design requirements called for a vehicle to carry 250 to 300 passengers over a range of 5,000 to 6,000 nautical miles. The study was initially unconstrained in terms of vehicle characteristic, such as cruise speed, propulsion systems, fuels, or structural materials. Analyses led to a focus on the most promising vehicle concepts. These were concepts that used a kerosene-type fuel and cruised at Mach numbers between 2.0 to 3.2. Further systems study identified the impact of environmental constraints (for community noise, sonic boom, and engine emissions) on economic attractiveness and technological needs. Results showed that current technology cannot produce a viable high-speed civil transport; significant advances are required to reduce takeoff gross weight and allow for both economic attractiveness and environmental accepatability. Specific technological requirements were identified to meet these needs.

Source record↗
NASA NTRS1989

A solid state lightning propagation speed sensor

A device to measure the propagation speeds of cloud-to-ground lightning has been developed. The lightning propagation speed (LPS) device consists of eight solid state silicon photodetectors mounted behind precision horizontal slits in the focal plane of a 50-mm lens on a 35-mm camera. Although the LPS device produces results similar to those obtained from a streaking camera, the LPS device has the advantages of smaller size, lower cost, mobile use, and easier data collection and analysis. The maximum accuracy for the LPS is 0.2 microsec, compared with about 0.8 microsecs for the streaking camera. It is found that the return stroke propagation speed for triggered lightning is different than that for natural lightning if measurements are taken over channel segments less than 500 m. It is suggested that there are no significant differences between the propagation speeds of positive and negative flashes. Also, differences between natural and triggered dart leaders are discussed.

Mach, Douglas M.↗
NASA NTRS1989

Motion sickness and gastric myoelectric activity as a function of speed of rotation of a circular vection drum

Motion sickness symptoms and electrogastrograms (EGGs) were obtained from 60 healthy subjects while they viewed an optokinetic drum rotated at one of four speeds: 15, 30, 60 or 90 deg/s. All subjects experienced vection, illusory self-motion. Motion sickness symptoms increased as drums speed increased up to 60 deg/s. Power, spectral intensity, of the EGG at the tachygastria frequencies (4-9 cpm) was calculated at each drum rotation speed. The correlation between the motion sickness symptoms and the power at 4-9 cpm was significant. Thus, drum rotation speed influenced the spectral power of the EGG at 4-9 cpm, tachygastria, and the intensity of motion sickness symptoms.

Hu, Senqi↗
NASA NTRS1989

On the structure, interaction, and breakdown characteristics of slender wing vortices at subsonic, transonic, and supersonic speeds

Slender wing vortex flows at subsonic, transonic, and supersonic speeds were investigated in a 6 x 6 ft wind tunnel. Test data obtained include off-body and surface flow visualizations, wing upper surface static pressure distributions, and six-component forces and moments. The results reveal the transition from the low-speed classical vortex regime to the transonic regime, beginning at a freestream Mach number of 0.60, where vortices coexist with shock waves. It is shown that the onset of core breakdown and the progression of core breakdown with the angle of attack were sensitive to the Mach number, and that the shock effects at transonic speeds were reduced by the interaction of the wing and the lead-edge extension (LEX) vortices. The vortex strengths and direct interaction of the wing and LEX cores (cores wrapping around each other) were found to diminish at transonic and supersonic speeds.

Erickson, Gary E.↗
NASA NTRS1989

Average electric wave spectra across the plasma sheet and their relation to ion bulk speed

Using 4 months of tail data obtained by the ELF/MF spectrum analyzer of the wave experiment and the three-dimensional plasma instrument on board the AMPTE/IRM satellite, a statistical survey on the electric wave spectral density in the earth's plasma sheet has been conducted. More than 50,000 10-s-averaged electric wave spectra were analyzed with respect to differences between their values in the inner and outer central plasma sheet and the plasma sheet boundary layer as well as their dependence on radial distance and ion bulk speed. High-speed flows are dominated by broadband electrostatic noise with highest spectral densities in the plasma sheet boundary, where broadband electrostatic noise also exists during periods of low-speed flows. The broadband electrostatic noise has a typical spectral index of about -2. During low-speed flows the spectra in the central plasma sheet show distinct emissions at the electron cyclotron odd half-harmonic and upper hybrid frequency. Wave intensities during episodes of fast perpendicular flows are higher than those associated with fast parallel flows.

Baumjohann, W.↗
NASA NTRS1990

Solar wind speed and coronal flux-tube expansion

The hypothesis that the solar wind speed at 1 AU and the rate of magnetic flux-tube expansion in the corona are inversely correlated is shown to be consistent with observations extending over the last 22 years. This empirical relationship allows the daily wind speeds at earth to be predicted from a current-free extrapolation of the observed photospheric field into the corona. The narrow boundaries of high-speed wind streams are attributed to steep gradients in the flux-tube expansion rates at the edges of coronal holes. When a heliospheric current sheet is included in the model, it is found that the flux tubes near the hole axis, although diverging more slowly than those near the hole boundary in the corona, have undergone the greatest net expansion at 1 AU, an effect consistent with the low densities within high-speed streams.

Wang, Y.-M.↗
NASA NTRS1990

Canard-wing vortex interactions at subsonic through supersonic speeds

The NASA-Ames 6 x 6-foot Transonic/Supersonic Wind Tunnel has been used to conduct a study of canard-wing flowfield interactions at sub-, trans-, and supersonic speeds, giving attention to vortex interactions, vortex breakdown, shock-wave development, and vortex-shock interactions. The results obtained show that the canard-wing flowfield interaction delays vortex breakdown to a higher angle-of-attack at sub- and transonic speeds; while the flowfield interference eliminates shock-induced secondary boundary layer separation on the wing, it does not alter the location and development of a rear shock wave extending laterally across the wing. A canard-induced upwash field accelerates the upward migration of the wing vortex at sub-through-supersonic speeds, but is most pronounced at transonic speeds due to the interaction of the vortical flow with the rear shock wave.

Erickson, Gary E.↗
NASA NTRS1989

CFD analysis for high speed inlets

The increased national interest in high speed flight has increased research for high speed propulsion components. The highly 3-D flows present in supersonic/hypersonic inlets are currently being studied at NASA-Lewis both experimentally and computationally using a family of steady Parabolized Navier-Stokes (PNS) and Navier-Stokes (NS) solvers and unsteady NS solvers. Some of the results of these efforts are presented with an emphasis on the comparison of the computational and experimental results. The flow in high speed inlets typically involves the interaction of compression shock waves and boundary layers on the internal surfaces. The fundamentals of these interactions have been studied experimentally for many years, while more recently, computations have been used to study these complex 3-D flow fields. Attempts to control the flow through boundary layer bleed are being investigated computationally prior to wind tunnel experiments. The ultimate goal is the higher performing inlets required for high speed flight.

Benson, Tom↗
NASA NTRS1990

Highball: A high speed, reserved-access, wide area network

A network architecture called Highball and a preliminary design for a prototype, wide-area data network designed to operate at speeds of 1 Gbps and beyond are described. It is intended for applications requiring high speed burst transmissions where some latency between requesting a transmission and granting the request can be anticipated and tolerated. Examples include real-time video and disk-disk transfers, national filestore access, remote sensing, and similar applications. The network nodes include an intelligent crossbar switch, but have no buffering capabilities; thus, data must be queued at the end nodes. There are no restrictions on the network topology, link speeds, or end-end protocols. The end system, nodes, and links can operate at any speed up to the limits imposed by the physical facilities. An overview of an initial design approach is presented and is intended as a benchmark upon which a detailed design can be developed. It describes the network architecture and proposed access protocols, as well as functional descriptions of the hardware and software components that could be used in a prototype implementation. It concludes with a discussion of additional issues to be resolved in continuing stages of this project.

Mills, David L.↗
NASA NTRS1991

The direct simulation of high-speed mixing-layers without and with chemical heat release

A direct numerical simulation of high speed reacting and non-reacting flows for H2-air systems is presented. The calculations are made for a convective Mach number of 0.38 with hyperbolic tangent initial profile and finite rate chemical reactions. A higher-order numerical method is used in time accurate mode to time advance the solution to a statistical steady state. About 600 time slices of all the variables are then stored for statistical analysis. It is shown that most of the problems of high-speed combustion with air are characterized by relatively weak heat release. The present study shows that: (1) the convective speed is reduced by heat release by about 10 percent at this convective Mach number M(sub c) = 0.38; (2) the variation of the mean and rms fluctuation of temperature can be explained on the basis of temperature fluctuation between the flame temperature and the ambient; (3) the growth rate with heat release is reduced by 7 percent; and (4) the entrainment is reduced by 25 percent with heat release. These differences are small in comparison with incompressible flow dynamics, and are argued to be due to the reduced importance of heat release in comparison with the large enthalpy gradients resulting from the large-scale vortex dynamics. It is finally suggested that the problems of reduced mixing in high-speed flows are not severely complicated by heat release.

Sekar, B.↗
NASA NTRS1991

Technology needs for high speed rotorcraft (2)

An analytical study was conducted to identify rotorcraft concepts best capable of combining a cruise speed of 350 to 450 knots with helicopter-like low speed attributes, and to define the technology advancements needed to make them viable by the year 2000. A systematic approach was used to compare the relative attributes and mission gross weights for a wide range of concepts, resulting in a downselect to the most promising concept/mission pairs. For transport missions, tilt-wing and variable diameter tilt-rotor (VDTR) concepts were found to be superior. For a military scout/attack role, the VDTR was best, although a shrouded rotor concept could provide a highly agile, low observable alternative if its weight empty fraction could be reduced. A design speed of 375 to 425 knots was found to be the maximum desirable for transport missions, with higher speed producing rapidly diminishing benefits in productivity. The key technologies that require advancement to make the tilt-wing and VDTR concepts viable are in the areas of wing and proprotor aerodynamics, efficient structural design, flight controls, refinement of the geared flap pitch control system, expansion of the speed/descent envelope, and the structural and aerodynamic tradeoffs of wing thickness and forward sweep. For the shrouded rotor, weight reduction is essential, particularly with respect to the mechanism for covering the rotor in cruise.

Scott, Mark W.↗
NASA NTRS1990

Aeroacoustic effects of reduced aft tip speed at constant thrust for a model counterrotation turboprop at takeoff conditions

A model high-speed, advanced counterrotation propeller, F7/A7, was tested in the NASA Lewis Research Center's 9- by 15-foot anechoic wind tunnel at simulated takeoff and approach conditions of Mach 0.2. The propeller was operated in a baseline configuration with the forward and aft rotor blade setting angles (36.2deg and 35.4 deg) and forward and aft rotational speeds essentially equal. Two additional configurations were tested with the aft rotor at increased blade setting angles and the rotational speed reduced to achieve overall performance similar to that of the baseline configuration. The aft rotor blade angles were adjusted such that the thrust and power absorption for each rotor remained the same as for the baseline configuration. Acoustic data were taken with an axially translating microphone probe that was attached to the tunnel floor. Concurrent aerodynamic data were taken to define propeller operating conditions. The aft rotor fundamental tone was about 6 dB lower with the 36.2 deg and 38.4 deg blade setting angles, and about 9 dB lower with the 36.2 and 41.4 deg blade setting angles. Predicted noise reductions based on tip speed considerations were 5 and 9.5 dB, respectively, for the two altered blade setting angles.

Woodward, Richard P.↗
NASA NTRS1990

Effect of voluntary vs. artificial activation on the relationship of muscle torque to speed

The suggestion by Phillips and Petrofsky (1980) and Wickiewicz et al. (1984) that artificial activation of the knee extensor muscles should result in greater relative changes in torque than those evident with maximal voluntary activation is examined by investigating the speed-torque relationship of the right knee extensor muscle group in eight human subjects in whom activation was achieved by 'maximal' voluntary effort or by electrical stimulation. Torque was measured at a specific knee angle during isokinetic concentric or eccentric actions at velocities between 0.17 and 3.66 rad/s and during isometric actions. It is shown that, with artificial activation, the relative changes in both eccentric and concentric torque were greater as the speed increased; the speed-torque relationship was independed of the extent of activation and was similar to that of an isolated muscle. On the other hand, activation by the central nervous system during maximal effort depended on the speed and the type of muscle action performed.

Dudley, Gary A.↗
NASA NTRS1990

Suggested future directions in high-speed transition experimental research

Historical developments in the area of high-speed experimental transition research are outlined, and future directions in this area as determined by the panel membership are listed. The directions include measurement and modeling of initial disturbance fields, both in ground facilities and flight, for all modes; development of advanced high-speed instrumentation for disturbance field measurements, measurements of the details of receptivity in multitudinous flows; further development and use of high-speed quiet tunnels; stability and transition studies for multitudinous flows; detailed studies of the transitional region for boundary layers, free flows, vortices separated flows, corner flows, etc.; and studies of flow-chemistry effects on transition phenomena. Applied research such areas as the physics of perforated-surface suction stabilization and the resolution of anomalies in the existing high-speed database is also suggested.

Bushnell, Dennis↗