Search NASA⌕ Search

SEARCH · Search NASA

Results for “tensile fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Graphite/polyimide composites with improved toughness

Studies were performed to determine the toughness characteristics of composites prepared from modified addition-type polyimides, using Celion 6000 graphite fiber as the reinforcement. The polyimides were prepared from aromatic diamines containing flexibilizing ether connecting groups. The composite flexural and short beam shear strengths were determined at room temperature and elevated temperatures. Composite toughness was evaluated using 10 deg off axis tensile tests and double cantilever beam fracture tests at room temperature. The effects of the flexibilized resin structure on composite mechanical properties, toughness characteristics, and thermo-oxidative stability are discussed.

Delvigs, Peter↗
NASA NTRS1989

Identification of a cast iron alloy containing nonstrategic elements

A program was performed to address the mechanical and environmental needs of Stirling engine heater head and regenerator housing components, while reducing the dependence on strategic materials. An alloy was developed which contained no strategic elemental additions per se. The base is iron with additions of manganese, molybdenum, carbon, silicon, niobium, and ferro-chromium. Such an alloy should be producible on a large scale at very low cost. The resulting alloy, designated as NASAUT 4G-Al, contained 15 Mn, 15 Cr, 2 Mo, 1.5 C, 1.0 Si, 1.0 Nb (in weight percent) with a balance of Fe. This alloy was optimized for chemistry, based upon tensile strength, creep-rupture strength, fracture behavior, and fatigue resistance up to 800 C. Alloys were also tested for environmental compatibility. The microstructure and mechanic properties (including hardness) were assessed in the as-cast condition and following several heat treatments, including one designed to simulate a required braze cycle. The alloy was fabricated and characterized in the form of both equiaxed and columnar-grained castings. The columnar grains were produced by directional solidification, and the properties were characterized in both the longitudinal and transverse orientations. The NASAUT 4G-Al alloy was found to be good in cyclic-oxidation resistance and excellent in both hydrogen and hot-corrosion resistance, especially in comparison to the baseline XF-818 alloy. The mechanical properties of yield strength, stress-rupture life, high-cycle-fatigue resistance, and low-cycle-fatigue resistance were good to excellent in comparison to the current alloy for this application, HS-31 (X-40), with precise results depending in a complex manner on grain orientation and temperature. If required, the ductility could be improved by lowering the carbon content.

Cooper, C. V.↗
NASA NTRS1989

Effect of a high temperature cycle on the mechanical properties of silicon carbide/titanium metal matrix composites

An investigation is conducted of the effects of the SPF/DB cycle on continuous SiC fiber-reinforced Ti-15V-3Cr-3Al-3Sn composite's matrix, fiber, and matrix-fiber interface. The fibers in question, designated SCS-6, have a carbon core and thin, carbon-rich surface. The fatigue endurance limit at 50,000 cycles for the SPF/DB specimens was 50 percent lower than for the as-fabricated material. The substantial changes in tensile strength, fatigue life, and fracture-surface appearance due to the SPF-DB cycle are explained by a difference in the failure mechanisms due to SPF/DB-induced changes in the fiber/matrix interface strength.

Naik, R. A.↗
NASA NTRS1996

Yeh-Stratton Criterion for Stress Concentrations on Fiber-Reinforced Composite Materials

This study investigated the Yeh-Stratton Failure Criterion with the stress concentrations on fiber-reinforced composites materials under tensile stresses. The Yeh-Stratton Failure Criterion was developed from the initial yielding of materials based on macromechanics. To investigate this criterion, the influence of the materials anisotropic properties and far field loading on the composite materials with central hole and normal crack were studied. Special emphasis was placed on defining the crack tip stress fields and their applications. The study of Yeh-Stratton criterion for damage zone stress fields on fiber-reinforced composites under tensile loading was compared with several fracture criteria; Tsai-Wu Theory, Hoffman Theory, Fischer Theory, and Cowin Theory. Theoretical predictions from these criteria are examined using experimental results.

Yeh, Hsien-Yang↗
NASA NTRS1973

Spallation and fracture resulting from reflected and intersecting stress waves.

Discussion of the effects of stress waves produced in solid by explosions or high-velocity impacts. These waves rebound from free surfaces in the form of tensile waves that are capable of causing internal fractures or spallation of the material. The high-speed framing camera is shown to be an important tool for observing the stress waves and fracture in transparent targets, and its photographs provide valuable information on the mechanics of fracture.

Kinslow, R.↗
NASA NTRS1982

Interfacial fracture of Space-Shuttle thermal-protection system

Stable crack growth and fracture at the interface of undensified LI-900 reusable surface insulation (RSI) tile and the Nomex strain isolation pad (SIP) of the Space-Shuttle thermal-protection system (TPS) were modeled by double-edged notch-tension specimens. These specimens were loaded under uniaxial tension or 50-Hz cyclic loading and the resultant stable crack growth leading to eventual fracture was monitored by a videocamera. These tests showed that successive local tear-outs due to local tensile overload in the RSI tile resulted in the interfacial fracture where the crack-tip opening angle, CTOA, of the SIP was related to initiation and intermittent stable crack propagation. Fractures in similar static and dynamic test specimens using densified LI-900 RSI tiles occurred in the undensified regions of the RSI tiles. These failures were consistent with the above failure mechanism based on the local tensile strength of the undensified LI-900 RSI tile. The intermittent stable crack growth of undensified LI-900 RSI tile was reproduced by a deterministic, two-dimensional finite-element model with SIP of variable elastic moduli.

Komine, A.↗
NASA NTRS2007

Polymethylmethacrylate (PMMA) Material Test Results for the Capillary Flow Experiments (CFE)

In support of the Capillary Flow Experiments (CFE) program, several polymethylmethacrylate (PMMA) flight vessels were constructed. Some vessels used a multipiece design, which was chemically welded together. Due to questions regarding the effects of the experiment fluid (silicone oil) on the weld integrity, a series of tests were conducted to provide evidence of the adequacy of the current vessel design. Tensile tests were conducted on PMMA samples that were both in the as-received condition, and also aged in air or oil for up to 8 weeks. Both welded and unwelded samples were examined. Fracture of the joints was studied using notched tensile specimens and Brazilian disk tests. Results showed that aging had no effect on tensile properties. While the welded samples were weaker than the base parent material, the weld strength was found to be further degraded by bubbles in the weld zone. Finally a fracture analysis using the worst-case fracture conditions of the vessel was performed, and the vessel design was found to have a factor of three safety margin.

Lerch, Bradley A.↗
NASA NTRS2005

Wavy Lineaments on Europa: Fracture Propagation into Combined Nonsynchronous and Diurnal Stress Fields

Understanding the processes that have operated on Europa and the manner in which they may have changed through time is fundamental to understanding the satellite's geology and present-day habitability. Previous studies have shown that lineament patterns on Europa can be explained by accumulation of tensile stress from slow nonsynchronous rotation (NSR), while the cycloidal planforms of other Europan lineaments can be explained if fractures propagate through a diurnally changing tensile stress field. We find that fractures propagated into combined diurnal and NSR stress fields can be "wavy" in planform for NSR stress accumulated over ~2 to 8 of ice shell rotation and average propagation speeds of approx. 1 to 3 m/s. The variety of Europa's observed lineament planforms from cycloidal, to wavy, to arcuate can be produced by accumulation of NSR stress relative to the diurnal stress field. Varying proportions of these stress mechanisms plausibly may be related to a time-variable (slowing) NSR rate.

Crawford, Zane↗
NASA NTRS1986

Tidal reorientation and the fracturing of Jupiter's moon Europa

The lineaments on Europa are discussed in terms of the orientation of the lineaments relative to the tensile stress trajectories due to tidal distortions and to nonsynchronous rotation. The cracks are noticeable by their darker albedo compared to the presumed water ice surrounding them. The stress trajectories for tidal distortion of a thin elastic shell are superimposed on Mercator projection maps of the lineaments. It is shown that the lineaments are mainly oriented at high angles to the tensile stress trajectories that would be expected for regularly occurring nonsynchronous rotation, i.e., extensional fractures would appear. The reorientation motions which would cause the fractures are estimated. It is suggested that the fractures occur episodically to release stresses built up on the tensile surface of the crust during the continuous nonsynchronous rotation of Europa.

Mcewen, A. S.↗
NASA NTRS1985

Design of stiffened composite panels with a fracture constraint

An automated procedure for designing minimum-weight composite panels subject to a local damage constraint under tensile loading was developed. A finite element program based on linear elastic fracture mechanics for calculating stress intensity factors (SIF) was incorporated in the design cycle. Panel fracture toughness was obtained by using a strain based criterion. A general purpose mathematical optimization algorithm was used for the weight minimization. Analytical sensitivity derivatives of the SIF employing the adjoint variable technique was used to enhance the computational efficiency of the procedure. Design results for both unstiffened and stiffened plates are presented.

Gurdal, Z.↗
DOE OSTI2024

Microstructural characterization and equibiaxial flexural strength of CeO 2 and Ti-doped CeO 2

In this study, the synthesis of CeO 2 and titanium dioxide (TiO 2 ) doped CeO 2 (TDC) monoliths are investigated, and their fracture strength is assessed using an equibiaxial flexure testing technique at room temperature. Pellets were synthesized using conventional powder processing and sintering methods to produce the desired characteristics. The TiO 2 dopant concentration was optimized at 0.1 wt % TiO 2 to obtain dense, solid-solution pellets with an enhanced grain microstructure. A ball-on-ring fixture was used to obtain the TRS and Weibull parameters of over 30 pellets for CeO 2 and 0.1 wt % TDC to compare fracture behavior. The TRS of CeO 2 pellets ranged from 88 to 160 MPa and the TRS of 0.1 wt % TDC pellets ranged from 102 to 171 MPa, both being consistent with published values. Weibull parameters, such as characteristic strength and Weibull modulus, were extracted as 129 MPa and 8.5 for CeO 2 and 150 MPa and 9.3 for 0.1 wt % TDC, respectively. Although Hertzian contact damage was observed on compressive surfaces, failure initiation occurred on the tensile surfaces of both types of samples. Fracture surface analysis for CeO 2 indicated a predominantly intergranular fracture while 0.1 wt % TDC had a predominantly transgranular fracture mode. Finally, the TRS of 0.1 wt % TDC resulted in increased Weibull parameters when compared to CeO 2 , indicating sample chemistry and microstructure impact mechanical behavior for these samples.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Fracture of boron filaments in an aluminum matrix.

The B-Al composite specimens tested in this study were fabricated by diffusion bonding of 1230 aluminum foil and boron filaments placed in alternate layers, using an acrylic resin solution to maintain filament spacing. The specimens were put under tensile stresses parallel to the filaments, and filament fracture was monitored acoustically under loads. Fracture of specimens under loads was caused by break propagation with a characteristic wedge-type fragmentation pattern indicating its direction. The aluminum foil matrix of the specimens failed by ductile shear type fracture after the break of the filaments.

Steele, J. H.↗
NASA NTRS1983

Fracture behavior of the Space Shuttle thermal protection system

Stable crack-growth and fracture-toughness experiments were conducted using precracked specimens machined from LI-900 reusable surface insulation (RSI) tiles of the Space Shuttle thermal protection system (TPS) at room temperature. Similar fracture experiments were conducted on fracture specimens with preexisting cracks at the interface of the tile and the strain isolation pad (SIP). Stable crack growth was not observed in the LI-900 tile fracture specimens which had a fracture toughness of 12.0 kPa sq rt of m. The intermittent subcritical crack growth at the tile-pad interface of the fracture specimens was attributed to successive local pull-outs due to tensile overload in the LI-900 tile and cannot be characterized by linear elastic fracture mechanics. No subcritical interfacial crack growth was observed in the fracture specimens with densified LI-900 tiles where brittle fracture initiated at an interior point away from the densification.

Komine, A.↗
NASA NTRS1987

Fracture surfaces of irradiated composites

Electron microscopy was used to analyze the fracture surfaces of T300/934 graphite/epoxy unidirectional off-axis tensile coupons which were subjected to 1.0-MeV electron radiation at a rate of 50 Mrad/h for a total dose of 10 Grad. Fracture surfaces from irradiated and nonirradiated specimens tested at 116 K, room temperature, and 394 K were analyzed to assess the influence of radiation and temperature on the mode of failure and variations in constituent material as a function of environmental exposure. Micrographs of fracture surfaces indicate that irradiated specimens are more brittle than nonirradiated specimens at low temperatures. However, at elevated temperatures the irradiated specimens exhibit significantly more plasticity than nonirradiated specimens.

Milkovich, Scott M.↗
NASA NTRS2024

Tensile Behavior and High-Cycle Fatigue Durability of a SiC/SiC Ceramic-Matrix Composite Without and With Simulated Cooling Holes

High-cycle fatigue (HCF) behavior of a melt-infiltrated, prepreg SiC/SiC composite was investigated using specimens without and with simulated cooling holes at 816 and 1,316 °C. The ceramic-matrix composite (CMC) material used for this study was fabricated by GE Aviation and had a ply configuration of [0/90/0] 3 . HCF tests were conducted with an R-ratio of 0.6 and a cyclic frequency of 30 Hz. Maximum tensile gross-section stresses used in the HCF tests ranged from 152 to 359 MPa. Runout in HCF was defined as 30 million cycles (278 h) at both temperatures. Monotonic tensile tests were conducted at room temperature (RT) on as-received CMC specimens and on HCF runout specimens without and with holes to determine residual tensile strengths. Digital image correlation (DIC) and acoustic emission (AE) techniques were used to monitor progression of damage in RT tensile tests on specimens without and with holes. Fractography was performed on a limited number of specimens without and with holes to determine morphology of fracture surfaces. Representative RT stress-strain behavior, elevated temperature HCF behavior at the two temperatures, and RT residual tensile strengths of HCF runout specimens are documented in this report. Select examples of DIC and AE data from RT tensile tests on specimens without and with holes and typical features observed on fracture surfaces of specimens tested under tensile and HCF conditions are also discussed.

Ceramic matrix composite↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
NASA NTRS1983

The dynamic tensile strength of ice and ice-silicate mixtures

The dynamic tensile strength of icy media is measured at strain rates on the order of 10,000/sec to aid in the understanding of impact and cratering phenomena. Compressed samples consisting of ice and ice-silicate mixtures with 5 and 30 wt % sand were impacted at temperatures between 230 and 250 K by projectile plexiglas plates imparting the required strain rates in less than 0.75 microsec. Taking the tensile stress corresponding to the transition from intact to spalled or fragmented samples as the dynamic tensile strength, strengths of 17, 20 and 22 MPa were obtained for the pure ice, 5 wt % sand, and 30 wt % sand specimens, respectively. The values lie considerably above those observed in static testing. A continuum fracturing model is used to obtain relations between tensile strength and stress rate as well as to derive stress and damage histories during tensile loading and the size distribution of icy fragments as a function of strain rate.

Lange, M. A.↗
DOE OSTI2021

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗