SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Computer simulation study to determine normality or nonnormality on any given population of sampled data - statistical probability distribution
Blunt body reentry vehicle aerodynamic heating determination
Statistical analysis of gyroscopic drift rate data for computer simulation of inertial navigator output error
Cryptanalytic technique for evaluating nickel- cadmium battery cell failure characteristic data
Development, and evaluation of thin film substrates containing sodium niobate capacitors, or sodium niobate dielectric material
New methods for obtaining stability derivatives from flight data
Buckling data review for stiffened cylinder failures during axial compression and bending
Data are presented on velocity measurements made with hot wire anemometers in the wake of a model of the CV-990 aircraft and a rectangular wing in the NASA-Ames 2.14x3.05 meter (7- by 10-foot) wind tunnels. Variables included angle of attack, tunnel speed and axial distance up to 12 chord lengths downstream from the wing trailing edge. Effects of deflecting trailing edge flaps and small spoiler panels are shown.
Explore the source record for details and available documents.
Data from record tracks of all accelerometers is injected simultaneously into electronic circuits which convert inputs into single, composite graphical representation. Three adequate methods of processing data: peak acceleration at a frequency, average of all channels, and quad-mean of all channels.
A study was conducted in which available airload and blade response data for the NH-3A and CH-53A rotors were analyzed in an attempt to provide greater insight into the sources of rotor vibratory loads in both level and maneuvering flight. Primary emphasis in the study was placed on examining and understanding causes of high-frequency rotor control loads. Secondary objectives were: (1) to examine the effect of number of rotor blades on hub vibratory shear forces and (2) to assess which of the many terms appearing in the hub vibratory shear force expression were of most significance.
Explore the source record for details and available documents.
Two methods for extracting stability derivatives from flight data are compared. A modified Newton-Raphson quasilinearization minimization technique and a digital-analog (hybrid) matching technique were used to analyze the same data maneuvers obtained from two aircraft. About 70 maneuvers from an F-111E aircraft were analyzed over a Mach number range of 0.3 to 2.0 and an angle of attack range of 3 to 19 degrees. About 20 maneuvers were analyzed for the X-24A lifting body at Mach numbers of 0.5, 0.8, and 0.9, and an angle of attack range of 4 to 13 degrees. Stability derivatives were extracted from these maneuvers and the results from the two techniques, along with wind tunnel results, were compared.
For abstract, see N74-34343.
A method is presented for obtaining the mass, stiffness, and damping parameters of a linear mathematical model, having fewer degrees of freedom than the structure it represents, directly from dynamic response measurements on the actual helicopter without a priori knowledge of the physical characteristics of the fuselage. The only input information required in the formulation is the approximate natural frequency of each mode and mobility data measured proximate to these frequencies with sinusoidal force excitation applied at only one point on the vehicle. The practicality and numerical soundness of the theoretical development was demonstrated through a computer simulation of an experimental program.
Computer programs for Omega data conversion, summary, and preparation for distribution are presented. Program logic and sample data formats are included, along with operational instructions for each program. Flight data (or data collected in flight format in the laboratory) is provided by the Ohio University Omega receiver base in the form of 6-bit binary words representing the phase of an Omega station with respect to the receiver's local clock. All eight Omega stations are measured in each 10-second Omega time frame. In addition, an event-marker bit and a time-slot D synchronizing bit are recorded. Program FDCON is used to remove data from the flight recorder tape and place it on data-processing cards for later use. Program FDSUM provides for computer plotting of selected LOP's, for single-station phase plots, and for printout of basic signal statistics for each Omega channel. Mean phase and standard deviation are printed, along with data from which a phase distribution can be plotted for each Omega station. Program DACOP simply copies the Omega data deck a controlled number of times, for distribution to users.
Measurements of the vortex system behind a T-33 aircraft were obtained by a Learjet equipped with a boom carrying a three-wire, hot-wire anemometry probe and other instrumentation. Analysis of the measurements using a computerized geometric method indicated the vortices had a core radius of approximately 0.11 meter with a maximum velocity of 25 meters per second. The hot-wire anemometer was found to be a practical and sensitive instrument for determining in-flight vortex velocities. No longitudinal instabilities, buoyant effects or vortex breakdowns were evident in the data which included vortex wake cross sections from 0.24 to 5.22 kilometers behind the T-33.