Search NASA⌕ Search

SEARCH · Search NASA

Results for “velocity data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Plasma and energetic particle structure upstream of a quasi-parallel interplanetary shock

ISEE 1, 2 and 3 data from 1978 on interplanetary magnetic fields, shock waves and particle energetics are examined to characterize a quasi-parallel shock. The intense shock studied exhibited a 640 km/sec velocity. The data covered 1-147 keV protons and electrons and ions with energies exceeding 30 keV in regions both upstream and downstream of the shock, and also the magnitudes of ion-acoustic and MHD waves. The energetic particles and MHD waves began being detected 5 hr before the shock. Intense halo electron fluxes appeared ahead of the shock. A closed magnetic field structure was produced with a front end 700 earth radii from the shock. The energetic protons were cut off from the interior of the magnetic bubble, which contained a markedly increased density of 2-6 keV protons as well as the shock itself.

Kennel, C. F.↗

Stability experiments in rotating-disk flow

An experimental study of the transitional flow on a flat disk, rotating in still air, has been conducted. Using digitized hot-wire data, the axes of the stationary spiral vortices, which are the primary instability mechanism for the disk flow, have been mapped-out in terms of both spatial coordinates and velocity fluctuations. Data are presented for a clean disk and for a disk with a single, isolated roughness element. The data show that the disk vortices are generated at discrete roughness disturbance sites on the disk and that they propagate and grow as wave packets. The familiar vortex pattern of 30 or so vortices results only when these wave packets have merged and filled the entire circumference. The appearance of stationary, secondary vortices prior to turbulent breakdown has also been observed. Comparisons with linear stability theory show reasonable agreement with measured growth rate data.

Wilkinson, S. P.↗

Vertical wind velocities from superpressure balloons - A case study using Eole data

A method for determining vertical wind velocities using the pressure- and temperature-change data from superpressure (constant-density) balloons was proposed in an earlier paper (1975). In this paper, we present a case study using actual balloon data to test the method. Data from the Eole balloon experiment were used to estimate the sign of vertical wind velocities, as well as the horizontal velocity field, near 200 mb over Australia. The resulting patterns of vertical velocity compare favorably with satellite pictures and with current models of flow near jet-stream maxima. Additionally, this study provides evidence that areas of vertical motion in the troposphere extend upward into the lower stratosphere without changing sign.

Banta, R. M.↗

RUSHMAPS: Real-Time Uploadable Spherical Harmonic Moment Analysis for Particle Spectrometers

RUSHMAPS is a new onboard data reduction scheme that gives real-time access to key science parameters (e.g. moments) of a class of heliophysics science and/or solar system exploration investigation that includes plasma particle spectrometers (PPS), but requires moments reporting (density, bulk-velocity, temperature, pressure, etc.) of higher-level quality, and tolerates a lowpass (variable quality) spectral representation of the corresponding particle velocity distributions, such that telemetry use is minimized. The proposed methodology trades access to the full-resolution velocity distribution data, saving on telemetry, for real-time access to both the moments and an adjustable-quality (increasing quality increases volume) spectral representation of distribution functions. Traditional onboard data storage and downlink bandwidth constraints severely limit PPS system functionality and drive cost, which, as a consequence, drives a limited data collection and lower angular energy and time resolution. This prototypical system exploit, using high-performance processing technology at GSFC (Goddard Space Flight Center), uses a SpaceCube and/or Maestro-type platform for processing. These processing platforms are currently being used on the International Space Station as a technology demonstration, and work is currently ongoing in a new onboard computation system for the Earth Science missions, but they have never been implemented in heliospheric science or solar system exploration missions. Preliminary analysis confirms that the targeted processor platforms possess the processing resources required for realtime application of these algorithms to the spectrometer data. SpaceCube platforms demonstrate that the target architecture possesses the sort of compact, low-mass/power, radiation-tolerant characteristics needed for flight. These high-performing hybrid systems embed unprecedented amounts of onboard processing power in the CPU (central processing unit), FPGAs (field programmable gate arrays), and DSP (digital signal processing) elements. The fundamental computational algorithm de constructs 3D velocity distributions in terms of spherical harmonic spectral coefficients (which are analogous to a Fourier sine-cosine decomposition), but uses instead spherical harmonics Legendre polynomial orthogonal functions as a basis for the expansion, portraying each 2D angular distribution at every energy or, geometrically, spherical speed-shell swept by the particle spectrometer. Optionally, these spherical harmonic spectral coefficients may be telemetered to the ground. These will provide a smoothed description of the velocity distribution function whose quality will depend on the number of coefficients determined. Successfully implemented on the GSFC-developed processor, the capability to integrate the proposed methodology with both heritage and anticipated future plasma particle spectrometer designs is demonstrated (with sufficiently detailed design analysis to advance TRL) to show specific science relevancy with future HSD (Heliophysics Science Division) solar-interplanetary, planetary missions, sounding rockets and/or CubeSat missions.

Figueroa-Vinas, Adolfo↗

Jet noise characteristics of unsuppressed duct burning turbofan exhaust system

Recent aero-acoustic tests of model coannular nozzles have shown that less noise is generated if the higher-velocity jet is exhausted from the outer annular passage rather than from the primary nozzle. These findings are of particular significance to a duct-burning turbofan (DBTF) engine being studied for application to an advanced supersonic transport. Unlike conventional turbofan engines that have peak velocities from the primary nozzle, it is possible to design a DBTF engine to have a fan velocity higher than that of the primary flow. Results are presented for a NASA-sponsored model test program that covers a range of fan to primary-area ratios from 0.75 to 1.2, and a range of fan to primary-velocity ratios from 0.4 to 2.8. Correlations are given that relate radiated sound power to fan velocity, fan to primary-velocity ratio, and fan to primary-area ratio. Corresponding exhaust-plume velocity-traverse data are presented which suggest that the observed noise benefits may be due to the more rapid decay of the annular flow because of shear stresses on the inner surface that result from the lower-velocity primary flow.

Packman, A. B.↗

Turbulence measurements in a transonic boundary layer and free-shear flow using laser velocimetry and hot-wire anemometry techniques

Quantitative measurements of the turbulence fluctuations in velocity and mass flux have been obtained in Mach 0.6 and 0.8 turbulent boundary layer and free-shear layer flows by laser velocimetry and hot-wire anemometry techniques. To evaluate the effects of compressibility, these transonic data are compared to available incompressible and supersonic results. Based on some simplifying assumptions, estimates of the rms density fluctuations are made for which error bounds are given. In addition to these fluctuation data, the compressible mean velocity data obtained with the laser velocimeter are presented and compared to pitot tube results. The investigation was conducted in the Ames 6- by 6-Foot Supersonic Wind Tunnel at free-stream Mach numbers of 0.6 and 0.8 for a unit Reynolds number of about 10,000,000 per meter.

Johnson, D. A.↗

Measurements in a separation bubble on an airfoil using laser velocimetry

An experimental investigation was conducted to measure the reverse flow within the transitional separation bubble that forms on an airfoil at low Reynolds numbers. Measurements were used to determine the effect of the reverse flow on integrated boundary-layer parameters often used to model the bubble. Velocity profile data were obtained on an NACA 663-018 airfoil at angle of attack of 12 deg and a chord Reynolds number of 140,000 using laser Doppler and single-sensor hot-wire anemometry. A new correlation is proposed based on zero velocity position, since the Schmidt (1986) correlations fail in the turbulent portion of the bubble.

Fitzgerald, Edward J.↗

Ignition of metals and alloys in gaseous oxygen by frictional heating

The ignition of metals and alloys have been investigated by rotating the end of a hollow cylinder against an identical stationary cylinder on a common axis (frictional heating) in gaseous oxygen. A ranking criterion that measures the resistance of metals and alloys to ignition is discussed. It consists of the power per unit area required for ignition conveniently expressed as the product of contact pressure P and average linear velocity ALV. Data are presented that demonstrate that materials that are high in nickel and copper require greater P-ALV products for ignition (more resistant to ignition) than materials that are high in iron. Aluminum and titanium alloys are shown to require the lowest P-ALV products for ignition. The effects of varying surface velocity, contact pressure, coefficient of friction, and oxygen pressure on P-ALV products required for ignition are discussed. The results indicate that P-ALV product required for ignition increases as surface velocity increases, as contact pressure decreases, and as the coefficient of friction decreases. Increasing oxygen pressure will cause the P-ALV product required for ignition to decrease at low pressures and increase at high pressures. In some cases, the relative ranking of materials based on P-ALV products will also change as conditions are varied. The data presented in this paper are from a development program to determine the merits of using such a dynamic test method for ranking materials for oxygen service. The results to date have indicated that more testing is required before this method can be made into a standard test. The data presented do show some of the major parameters affecting the ignition of materials when exposed to frictional heating. The repeatability of the data at any set of conditions have not been thoroughly investigated.

Benz, F. J.↗

Development of a Coherent Doppler Lidar for Precision Landing on Planetary Bodies

A coherent Doppler lidar has been developed by NASA for providing vector velocity and altitude data to landing vehicles. Future robotic and manned missions to planetary bodies demand precise ground-relative velocity and altitude data to execute complex descent maneuvers for safe, soft and pinpoint landing at a pre-designated site. Operating from over five kilometers altitude, this lidar provides velocity and range data within a few cm/sec and a few meters precision, respectively, depending on the vehicle dynamics. Two upcoming lunar landing missions will serve as the technology demonstration for robotic and manned landing missions to the Moon, Mars, and other solar system destinations. This paper describes the lidar design and its expected performance on landing vehicles.

Coherent Laser Radar↗

A Performance Assessment of an Airborne Separation Assistance System Using Realistic Complex Traffic Flows

This paper presents the results from a study that investigates the performance of a tactical Airborne Separation Assistance System (ASAS) in en route airspace, under varying demand levels, with realistic traffic flows. The ASAS concept studied here allows flight crews of equipped aircraft to perform separation from other air traffic autonomously. This study addresses the tactical aspects of an ASAS using aircraft state data (i.e. position and velocity) to detect and resolve projected conflicts. In addition, use of a conflict prevention system helps ASAS-equipped aircraft avoid maneuvers that may cause new conflicts. ASAS-capable aircraft are equipped with satellite-based navigation and Automatic Dependent Surveillance Broadcast (ADS-B) for transmission and receipt of aircraft state data. In addition to tactical conflict detection and resolution (CD&R), a complete, integrated ASAS is likely to incorporate a strategic CD&R component with a longer look-ahead time, using trajectory intent information. A system-wide traffic flow management (TFM) component, located at the FAA command center helps aircraft to avoid regions of excessive traffic density and complexity. A Traffic Alert and Collision Avoidance System (TCAS), as used today is the system of last resort. This integrated approach avoids sole reliance on the use of the tactical CD&R studied here, but the tactical component remains a critical element of the complete ASAS. The focus of this paper is to determine to what extent the proposed tactical component of ASAS alone can maintain aircraft separation at demand levels up to three times that of current traffic. The study also investigates the effect of mixing ASAS-equipped aircraft with unequipped aircraft (i.e. current day) that do not have the capability to self-separate. Position and velocity data for unequipped aircraft needs to be available to ASASequipped. Most likely, for this future concept, state data would be available from instrument flight rules (IFR) aircraft, equipped with at least ADS-B transmission capability. The objective is to reduce the number of losses of separation to a minimum and investigate the limits of tactical-only CD&R. Thus, the objective is not, expressly, to achieve zero losses of separation with tactical ASAS because this is one component of an integrated ASAS.

Smith, Jeremy C.↗

Global Positions and Velocities from One Year of GPS Data

A generalized no-fiducial approach has been developed to obtain global positions and velocities without fixing any individual position or velocity components. The method used can be applied to any global geodetic technique and proceeds in three general steps. First, daily solutions derived with weak constraints are combined to yield one global set of positions and velocities. Second, 14 minimal constraints are applied to remove uncertainties due to the loosely defined reference frame. Third, transformation from one reference frame to another is accomplished with a 14 parameter transformation. One year of daily FLINN solutions, each made with data from about 40 sites, have been combined to yield our best fit global model...

Heflin, M. B.↗

Experimental Investigation of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. The main emphasis in this paper is placed on flow field surveys performed at a Reynolds number of 100,000 with levels of freestream turbulence ranging from 0.8% to 3%. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Sohn, Ki-Hyeon↗

Experimental Investigation of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the y pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. The main emphasis in this paper is placed on flow field surveys performed at a y Reynolds number of 100,000 with levels of freestream turbulence ranging from 0.8% to 3%. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗

Longitudinal and Seasonal Variations in Nighttime Plasma Temperatures in the Equatorial Topside Ionosphere During Solar Maximum

Latitude profiles of the ion and electron temperatures and total ion concentration across the equatorial region near 800 km altitude are routinely obtained from Defense Meteorological Satellite Program (DMSP) spacecraft. We have examined these profiles at 2100 hours local time to discover the influences of field-aligned plasma transport induced by F region neutral winds. Such dependencies are readily seen by contrasting observations at different seasons and different longitudes distinguished by different magnetic declinations. These data show strong evidence for adiabatic heating produced by interhemispheric plasma transport. This heating manifests itself as a local temperature maximum that appears in the winter hemisphere during the solstices and is generally absent during equinox. A longitudinal variation in the appearance of this maximum is consistent with the roles of meridional and zonal winds in modulating the field-aligned plasma velocities. The data also show a local temperature minimum near the dip equator. However, it is not so easy to attribute this minimum to adiabatic cooling since transport of plasma from below and the latitude variation in the flux tube content may also produce such a minimum.

Venkatraman, Sarita↗

Thermospheric gravity waves near the source - Comparison of variations in neutral temperature and vertical velocity at Sondre Stromfjord

Theoretical predictions of thermospheric gravity wave oscillations are compared with observed neutral temperatures and velocities. The data were taken in February 1983 using a Fabry-Perot interferometer located on Greenland, close to impulse heat sources in the auroral oval. The phenomenon was modeled in terms of linearized equations of motion of the atmosphere on a slowly rotating sphere. Legendre polynomials were used as eigenfunctions and the transfer function amplitude surface was characterized by maxima in the wavenumber frequency plane. Good agreement for predicted and observed velocities and temperatures was attained in the 250-300 km altitude. The amplitude of the vertical velocity, however, was not accurately predicted, nor was the temperature variability. The vertical velocity did exhibit maxima and minima in response to corresponding temperature changes.

Herrero, F. A.↗

Processing Laser-Velocimetric Data By Vector Scanning

Velocity plots obtained in minutes instead of hours. Velocity scanning technique for processing flow-field data from pulsed-laser-velocimetry images into two-dimensional velocity-vector maps. Requires no special equipment other than charge-coupled-device (CCD) camera, circuitry to digitize output of camera, and computer. Once image data digitized, all processing done in computer.

Wernet, Mark P.↗

An experimental investigation of a swirling, axisymmetric, turbulent boundary layer with pressure gradient

The results of an experimental investigation designed to document data on both mean and turbulence quantities in the axisymmetric, swirling boundary layer (with and without a pressure gradient) flowing over a stationary cylinder downstream of a spinning cylindrical section are discussed. The pressure gradient was introduced into the flow field by a 25.4-mm-high, forward-facing circular step mounted on the stationary cylinder, the step height being nearly equal to the approaching boundary-layer thickness. All the measurements were made at upstream reference velocity of 36-37 m/sec, with the rotation of the spinner set to make its peripheral speed equal to the reference velocity. The data reported include measurements of surface pressure and the mean surface-shear-stress vector (using a miniature directional surface-fence gage) and oil-flow visualization studies of the stationary cylinder. The data indicate that the streamwise pressure gradient controls the development of the streamwise component of wall shear but leaves the peripheral component of wall shear practically unaffected.

Hebbar, S. K.↗

Accuracy Study of a 2-Component Point Doppler Velocimeter (PDV)

A two-component Point Doppler Velocimeter (PDV) which has recently been developed is described, and a series of velocity measurements which have been obtained to quantify the accuracy of the PDV system are summarized. This PDV system uses molecular iodine vapor cells as frequency discriminating filters to determine the Doppler shift of laser light which is scattered off of seed particles in a flow. The majority of results which have been obtained to date are for the mean velocity of a rotating wheel, although preliminary data are described for fully-developed turbulent pipe flow. Accuracy of the present wheel velocity data is approximately +/- 1 % of full scale, while linearity of a single channel is on the order of +/- 0.5 % (i.e., +/- 0.6 m/sec and +/- 0.3 m/sec, out of 57 m/sec, respectively). The observed linearity of these results is on the order of the accuracy to which the speed of the rotating wheel has been set for individual data readings. The absolute accuracy of the rotating wheel data is shown to be consistent with the level of repeatability of the cell calibrations. The preliminary turbulent pipe flow data show consistent turbulence intensity values, and mean axial velocity profiles generally agree with pitot probe data. However, there is at present an offset error in the radial velocity which is on the order of 5-10 % of the mean axial velocity.

Kuhlman, John↗