Results for “wind tunnel characterization” — Page 21

NASA NTRS1979

Aerodynamic performance of scarf inlets

A scarf inlet is characterized by having a longer lower lip than upper lip leading to both aerodynamic and acoustic advantages. Aerodynamically, a scarf inlet has higher angle of attack capability and is less likely to ingest foreign objects while the aircraft is on the ground. Acoustically, a scarf inlet provides for reduced inlet radiated noise levels below the engine as a result of upward reflection and refraction of inlet radiated noise. Results of a wind tunnel test program are presented which illustrate the aerodynamic performance of two different scarf inlet designs. Based on these results, scarf inlet performance is summarized in a way to illustrate the advantages and limitations of a scarf inlet compared to an axisymmetric inlet.

Abbott, J. M.↗

NASA NTRSDate not supplied

Experimental and Computational Examination of the Coandă Effect on the Space Launch System at Liftoff Conditions

During development of an aerodynamic database to cover ground wind loads, uncertainty quantification to account for the Coandă effect forced a closer look into how this phenomenon manifests on the Space Launch System. Aerodynamic data collected across the life of the pro-gram is explored to look for trends and the ability to characterize not just the bounds of forces and moments but also better understand their distributions. Experimental data collected in the NASA Langley 14- by 22-Foot Subsonic Tunnel is used to explore integrated forces and moments. This is followed up by a similar exploration using computational data generated using the Kestrel flow solver. After a survey of the data at large which confirms the existence of the Coandă states throughout the history of the program, a few highlighted cases are used to characterize the flow physics. This characterization is used to summarize how each Coandă state is predicted to load the vehicle.

Coandă Effect↗

NASA NTRS1985

Low Reynolds number separation bubble research at UTRC

The facilities and techniques being applied in investigations of laminar separation bubbles on low Re airfoils at the United Technologies Research Center are described. The research is focused on developing a database and predictive models for use in designing compressor, fan and turbine blades. Flow data are gathered primarily by laser Doppler velocimetry. Experimental procedures are being devised which will permit formation of a short bubble for characterizations of the velocity profiles in and around the bubble and boundary layer. Further tests are directed at defining the size and location of the bubble and the transition in the separated shear layer. The sensitivity of the bubble to alterations in the Re, pressure gradient, turbulence intensity and the turbulence scales will be examined. The effects of surface curvature and roughness on the bubble will also be studied. Details of the wind tunnel facility and the steps being taken to define conditions for reliably producing the short bubble are outlined.

Patrick, W. P.↗

NASA NTRS1996

Hypersonic Boundary Layer Stability Experiments in a Quiet Wind Tunnel with Bluntness Effects

Hypersonic boundary layer measurements over a flared cone were conducted in a Mach 6 quiet wind tunnel at a freestream unit Reynolds number of 2.82 million/ft. This Reynolds number provided laminar-to-transitional flow over the cone model in a low-disturbance environment. Four interchangeable nose-tips, including a sharp-tip, were tested. Point measurements with a single hot-wire using a novel constant voltage anemometer were used to measure the boundary layer disturbances. Surface temperature and schlieren measurements were also conducted to characterize the transitional state of the boundary layer and to identify instability modes. Results suggest that second mode disturbances were the most unstable and scaled with the boundary layer thickness. The second mode integrated growth rates compared well with linear stability theory in the linear stability regime. The second mode is responsible for transition onset despite the existence of a second mode subharmonic. The subharmonic disturbance wavelength also scales with the boundary layer thickness. Furthermore, the existence of higher harmonics of the fundamental suggests that nonlinear disturbances are not associated with 'high' free stream disturbance levels. Nose-tip radii greater than 2.7% of the base radius completely stabilized the second mode.

Lachowicz, Jason T.↗

NASA NTRS1994

Large-eddy simulation of flow through a plane, asymmetric diffuser

A challenge for traditional turbulence modeling, based on the Reynolds averaged Navier-Stokes equations, remains the accurate prediction of 'mild', adverse pressure-gradient driven separation from a smooth surface. With this study we want to explore the capability of large-eddy simulation to predict the separation which occurs on the deflected wall of an asymmetric, plane diffuser with opening angle of 10 deg. The flow through the plane diffuser exhibits some additional interesting physical phenomena which make it a challenging test case. In addition to 'mild' separation about halfway down the deflected ramp, the flow is characterized by a small backflow zone with stalled fluid in the rear part of the expanding section. The turbulent flow entering the diffuser is subject to combined adverse and radial pressure gradients stemming from the convex curvature. Finally the flow recovers into a developed, turbulent channel flow in the outlet section. Obi et al. provide measurements of mean flow, Reynolds stresses, and pressure recovery, which were obtained by means of LDV in a wind tunnel. The objective of this study is to investigate whether LES with the standard dynamic model is able to accurately predict the flow in the one-sided diffuser and to explore the resolution requirements and associated costs.

Kaltenbach, Hans-Jakob↗

NASA NTRS1989

Coherent structures in a boundary layer and shear layer of a turbulent backward-facing step flow

A wind tunnel experiment has been carried out at the NASA Ames Research Center to analyze the evolution of coherent structures from a boundary layer to a shear layer in a turbulent, backward-facing, step flow. A miniature X-wire/cold-wire probe has been used in conjunction with two arrays of cold wires, one aligned in the plane of main shear and the other in the spanwise direction of the flow, to detect and characterize delta-scale organized structures in the outer regions of the flow and to provide detailed information concerning these structures. Kinematic features of the events associated with the large scale structures were analyzed and topological pictures of the evolving flow, as well as the contributions to the Reynolds shear stress components are presented.

Jovic, Srba↗

NASA NTRS2012

Highlights from a Mach 4 Experimental Demonstration of Inlet Mode Transition for Turbine-Based Combined Cycle Hypersonic Propulsion

NASA is focused on technologies for combined cycle, air-breathing propulsion systems to enable reusable launch systems for access to space. Turbine Based Combined Cycle (TBCC) propulsion systems offer specific impulse (Isp) improvements over rocket-based propulsion systems in the subsonic takeoff and return mission segments along with improved safety. Among the most critical TBCC enabling technologies are: 1) mode transition from the low speed propulsion system to the high speed propulsion system, 2) high Mach turbine engine development and 3) innovative turbine based combined cycle integration. To address these challenges, NASA initiated an experimental mode transition task including analytical methods to assess the state-of-the-art of propulsion system performance and design codes. One effort has been the Combined-Cycle Engine Large Scale Inlet Mode Transition Experiment (CCE-LIMX) which is a fully integrated TBCC propulsion system with flowpath sizing consistent with previous NASA and DoD proposed Hypersonic experimental flight test plans. This experiment was tested in the NASA GRC 10 by 10-Foot Supersonic Wind Tunnel (SWT) Facility. The goal of this activity is to address key hypersonic combined-cycle engine issues including: (1) dual integrated inlet operability and performance issues-unstart constraints, distortion constraints, bleed requirements, and controls, (2) mode-transition sequence elements caused by switching between the turbine and the ramjet/scramjet flowpaths (imposed variable geometry requirements), and (3) turbine engine transients (and associated time scales) during transition. Testing of the initial inlet and dynamic characterization phases were completed and smooth mode transition was demonstrated. A database focused on a Mach 4 transition speed with limited off-design elements was developed and will serve to guide future TBCC system studies and to validate higher level analyses.

Foster, Lancert E.↗

NASA NTRS2004

Comparison of Rolling Moment Characteristics During Roll Oscillations for a Low and a High Aspect Ratio Configuration

Improvements in testing and modeling of nonlinear and unsteady aerodynamic effects for flight dynamics predictions of vehicle performance is critical to enable the design and implementation of new, innovative vehicle concepts. Any configuration which exhibits significant flow separation, nonlinear aerodynamics, control interactions or attempts maneuvering through one or more conditions such as these is, at present, a challenge to test, model or predict flight dynamic responses prior to flight. Even in flight test experiments, adequate models are not available to study and characterize the complex nonlinear and time-dependent flow effects occurring during portions of the maneuvering envelope. Traditionally, airplane designs have been conducted to avoid these areas of the flight envelope. Better understanding and characterization of these flight regimes may not only reduce risk and cost of flight test development programs, but also may pave the way for exploitation of those characteristics that increase airplane capabilities. One of the hurdles is that the nonlinear/unsteady effects appear to be configuration dependent. This paper compares some of the dynamic aerodynamic stability characteristics of two very different configurations - representative of a fighter and a transport airplane - during dynamic body-axis roll wind tunnel tests. The fighter model shows significant effects of oscillation frequency which are not as apparent for the transport configuration.

Brandon, Jay M.↗

NASA NTRS2015

Influences of Models on the Unsteady Pressure Characteristics of the NASA National Transonic Facility

Pressure fluctuations have been measured over the course of several tests in the National Transonic Facility to study unsteady phenomenon both with and without the influence of a model. Broadband spectral analysis will be used to characterize the length scales of the tunnel. Special attention will be given to the large-scale, low frequency data that influences the Mach number and force and moment variability. This paper will also discuss the significance of the vorticity and sound fields that can be related to the Common Research Model and will also highlight the comparisons to an empty tunnel configuration. The effectiveness of vortex generators placed at the interface of the test section and wind tunnel diffuser showed promise in reducing the empty tunnel unsteadiness, however, the vortex generators were ineffective in the presence of a model.

Jones, Gregory↗

NASA NTRSDate not supplied

A New Flow-Through Wind Tunnel Balance for Retropropulsion Testing

Supersonic retropropulsion is believed to be an enabling technology for large-scale human Mars lander vehicle concepts. Ground testing of such vehicles requires the development of new flow-through wind tunnel balances because no suitable balances exist. A new flow-through balance is designed that employs membranes in place of bellows, which have historically been used, and that passes the flow through load bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aero researchers a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.

Flow through balance↗

NASA NTRSDate not supplied

A New Flow-Through Balance for Retropropulsion Testing

Supersonic retropropulsion is believed to be an enabling technology for large-scale human Mars lander vehicle concepts. Ground testing of such vehicles requires the development of new flow-through wind tunnel balances because no suitable balances exist. A new flow-through balance is designed that employs membranes in place of bellows, which have historically been used, and that passes the flow through load bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aero researchers a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.

Flow through balance↗

NASA NTRS1985

An analysis of a separation bubble transition criterion at low Reynolds numbers

Factors which influence the criterion governing the length of the laminar region of a separation bubble on an airfoil at low Re were investigated. The criterion is the onset of separation when a critical Re value is surpassed. Wind tunnel data were gathered for the flow around a NACA 66(3)-018 airfoil at Re from 50,000-200,000. The data were taken with either hot-wire anemometers or pressure taps. The value of the critical Re was influenced by the chord Re, the angle of attack and the level of turbulence in the free stream. However, the turbulence levels examined, up to 0.184 percent, did not greatly affect the critical Re. Further characterizations of the effects of the three factors on the critical Re are necessary before the important features of separation bubbles can be identified with an acceptable level of certainty.

Schmidt, G. S.↗

NASA NTRSDate not supplied

Validation of a Mid-Fidelity Approach for Aircraft Stability and Control Characterization

This paper describes an efficient computational approach for aircraft aerodynamic model development intended for use in flight dynamics simulations. A commercial surface-vorticity flow solver called FlightStream is employed to predict performance, stability, and control characteristics for a NASA subscale electric vertical takeoff and landing aircraft in its isolated-airframe configuration. A framework is described to rapidly convert OpenVSP geometry into a form compatible with the FlightStream software. FlightStream predictions for the variation of aerodynamic force and moment coefficients with airflow angles and control surface deflection angles are compared to static wind-tunnel data to illustrate the process and assess the accuracy of FlightStream solutions. The results and approach presented in this paper are encouraging for use in rapid aerodynamic modeling and flight dynamics simulation development early in the aircraft design process.

aerodynamic modeling↗

NASA NTRS1957

Wall Interference in a Perforated Wind Tunnel

The theory of cascades, made up of a series of flat plates placed one behind the other, is extended to the case where the impinging stream is not uniform, and the deduced properties of this cascade-flow are then applied to the study of the wall interference between such as cascade-like boundary and a vortex-source type of singularity. It is shown that the induced velocities, produced by the presence of such a wall, are equal to what is obtained by action of a suitably chosen 'reflected' singularity situated on one side of the wall, together with the action of another suitably chosen 'transmitted' singularity placed on the other side. The concepts of a reflection factor and a transmission factor are introduced to characterize various types of tunnel boundary, whether this is composed of solid wall, open and closed sequences, or just a free fluid surface. These ideas are then extended to cover the situation in which a pair of such walls are allowed to coalesce, especially in the event that one of the walls consists of open and closed portions and the other is a fluid surface. This latter particular combination of boundaries is called a perforated wall. Finally, the interference arising from an arbitrary general singularity placed symmetrically in between two such perforated walls is analyzed, and these results are then applied to the determination of the particular kinds of wall geometry that will produce no interference effects in the case of a slender lifting wing and also in the case of a symmetric profile having a finite thickness.

Brescia, Riccardo↗

NASA NTRS1990

Development and fabrication of structural components for a scramjet engine

A program broadly directed toward design and development of long-life (100 hours and 1,000 cycles with a goal of 1,000 hours and 10,000 cycles) hydrogen-cooled structures for application to scramjets is presented. Previous phases of the program resulted in an overall engine design and analytical and experimental characterization of selected candidate materials and concepts. The latter efforts indicated that the basic life goals for the program can be reached with available means. The main objective of this effort was an integrated, experimental evaluation of the results of the previous program phases. The fuel injection strut was selected for this purpose, including fabrication development and fabrication of a full-scale strut. Testing of the completed strut was to be performed in a NASA-Langley wind tunnel. In addition, conceptual designs were formulated for a heat transfer test unit and a flat panel structural test unit. Tooling and fabrication procedures required to fabricate the strut were developed, and fabrication and delivery to NASA of all strut components, including major subassemblies, were completed.

Buchmann, O. A.↗

NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

boundary layer transition↗

NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

Boundary Layer Transition↗

NASA NTRS1983

Ejector nozzle test results at simulated flight conditions for an advanced supersonic transport propulsion system

Results are presented of wind tunnel tests conducted to verify the performance improvements of a refined ejector nozzle design for advanced supersonic transport propulsion systems. The analysis of results obtained at simulated engine operating conditions is emphasized. Tests were conducted with models of approximately 1/10th scale which were configured to simulate nozzle operation at takeoff, subsonic cruise, transonic cruise, and supersonic cruise. Transonic cruise operation was not a consideration during the nozzle design phase, although an evaluation at this condition was later conducted. Test results, characterized by thrust and flow coefficients, are given for a range of nozzle pressure ratios, emphasizing the thrust performance at the engine operating conditions predicted for each flight Mach number. The results indicate that nozzle performance goals were met or closely approximated at takeoff and supersonic cruise, while subsonic cruise performance was within 2.3 percent of the goal with further improvement possible.

Nelson, D. P.↗