Search NASA⌕ Search

SEARCH · Search NASA

Results for “wiring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Hot-wire anemometry for in-flight measurement of aircraft wake vortices

A development program has demonstrated that hot-wire anemometry can be used successfully on an aircraft in flight to make measurements of wake vortices produced by another aircraft. The probe, whose wires were made of platinum/rhodium, 10 microns in diameter, provides unambiguous results for inflow angles less than about 35 deg. off the probe axis. The high frequency response capability of the hot-wire system allows detailed measurement of the flow structure, and the study of aircraft hazards associated with wake turbulence.

Jacobsen, R. A.↗
NASA NTRS1978

Flying-hot-wire study of two-dimensional mean flow past an NACA 4412 airfoil at maximum lift

Hot-wire measurements have been made in the boundary layer, the separated region, and the near wake for flow past an NACA 4412 airfoil at maximum lift. The Reynolds number based on chord was about 1,500,000. The main instrumentation was a hot-wire probe mounted on the end of a rotating arm. A digital computer was used to control synchronized sampling of hot-wire data at closely spaced points along the probe arc. Ensembles of data were obtained at several thousand locations in the flow field. The data include intermittency, two components of mean velocity, and twelve mean values for double, triple, and quadruple products of two velocity fluctuations. The data are available on punched cards in raw form and also after use of smoothing and interpolation routines to obtain values on a fine rectangular grid aligned with the airfoil chord. The data are displayed in the paper as contour plots.

Coles, D.↗
NASA NTRS1980

Visualization of the laminar-turbulent transition in the flow over an airfoil using the smoke-wire technique

A flow visualization technique, referred to as the smoke-wire, was used for visualization of the transition of the free shear layer associated with the laminar separation bubble of a NACA 66 sub 3-018 airfoil section at low Reynolds number (50,000-130,000). The smoke-wire technique allows the introduction of fine smoke streaklines into the flow field through the electrical resistive heating of a very fine wire which has been coated with oil and which is located upstream from the leading edge of the airfoil section. Streakline data were collected using both high speed still and motion picture photography.

Batill, S. M.↗
NASA NTRS1982

Wire Whip Keeps Spray Nozzle Clean

Air-turbine-driven wire whip is clamped near spray-gun mount. When spray gun is installed, wire whip is in position to remove foam buildup from nozzle face. Two lengths of wire 1 to 2 inches long and about 0.03 inch in thickness are used. Foam spray would be prevented from accumulating on nozzle face by increasing purge flow and cutting vortex-generating grooves inside cap and on nozzle flats.

Carroll, H. R.↗
NASA NTRS1982

Eddy-Current Meter Would Check Weld Wire Online

Simple Technique samples an entire spool of welding wire to test for contamination or unauthorized filler wire. Since unit monitors entire length of wire used in welding, completed welds need not be inspected individually. Technique would save time, avoiding human interface and production delays.

Bailey, G. R.↗
NASA NTRS1984

Wire Retrieves Broken Pin

Safety wire retains pieces of broken tool. Retrieval wire running through shaft of tool used to pull pieces of tool out of hole, should tool break during use. Safety wire concept suitable for pins subject to deflection or breakage.

Burow, G. H.↗
NASA NTRS1982

Prospects of increasing the strength of aluminum by reinforcing it with stainless steel wire (a review)

The theoretical and experimental strength of aluminum reinforced with stainless steel wire is analyzed. Various methods of producing the composite material and it's static and cyclical strengths are considered. The reinforcement of aluminum with stainless steel wire was accomplished from the perspective of increasing the specific strength of aluminum and it's alloys, increasing the strength of the material with respect to high and low temperatures, as well as increasing the cyclical strength. The production of the composite aluminum-stainless steel wire material with approximated or calculated strengthening is possible by any of the considered methods. The selection of the proper production technology depends on precise details and conditions of application of the material.

Botvina, L. R.↗
NASA NTRS1985

Wire-Identification Instrument

Instrument automatically tests each wire in multiwire cable and identifies specified wire to be segregated or labeled and locates wire connected to specified connector pin. Instrument made with readily available CMOS integrated circuits. More efficient and reliable than conventional continuity testers and less expensive than computer controlled units.

Lonborg, J. O.↗
NASA NTRS1985

Hot-Wire Probe for Compressible Subsonic Flow

Probe measures velocity, density, and total temperature fluctuations. Three-wire probe used with each wire operating at different overheat ratio. Technique extendable into transonic and low supersonic flow regimes without difficulty except for those problems usually associated with lengthy calibration and possible wire breaking.

Stainback, P. C.↗
NASA NTRS1984

Phase sensitive guidance sensor for wire-following vehicles

A guidance sensor for a wire-following vehicle which is phase sensitive, includes an array of coils positioned to sense the vertical component of a magnetic field produced by the ac current through the guidance wire. The outputs of the coils are fed to associated flip flops. Flip flops associated with coils, through which flux passes in one direction, e.g., up, are driven to one state, e.g., true, and flip flops associated with coils through which flux passes in the opposite direction, e.g., down, are driven to a false state. The control signal to guide the vehicle over the wire is a function of the number of flip flops in the true state. Circuitry is included to prevent flip flops from assuming a wrong state due to noise.

Hansen, G. R.↗
NASA NTRS1984

Heat Transfer Characteristics of Regenerator Matrix (Case of Packed Wire Gauzes)

The average heat transfer coefficient in the matrix of laminated wire screens (10 to 250 mesh) for a Stirling engine heat exchanger was studied experimentally. The data are correlated by N sub ud = 0.42 R sub ed 0.56 (3 or = R sub ed or = 400), and R sub ed are the Nusselt and Reynolds nubmers based on the wire diameter. The pressure drop decreased and the heat transfer increased as the wire diameter was decreased.

Hamaguchi, K.↗
NASA NTRS1984

Comment on 'Hy-wire measurements of atmospheric potential' by R. H. Holzworth

It is shown that the Hy-wire fluctuations in atmospheric potential measured by Holzworth (1983) were not changes in the global circuit. The close association between the Hy-wire potential variations and meteorological changes, as well as the lack of correlation between the potential and the Carnegie curve, indicates that the tethered balloon measurements were responding to local meteorological factors. The abnormally high potentials and the reversed curvature of the potential profiles suggest that the Hy-wire apparatus was not measuring atmospheric potentials accurately.

Markson, R.↗
NASA NTRS1984

Turbulence measurements in a complex flowfield using a crossed hot-wire

An X-wire probe was used to measure the time-mean and fluctuating velocities and shear stress in nonswirling nonreacting confined jet flows. Data were taken from an axisymmetric confined jet with an expansion ratio of 2 and an expansion angle of 90 deg, and from the same segment with a contraction nozzle. Velocity profiles developed faster in the confined jet than in the free jet, with the former experiencing higher turbulence levels and larger time-mean velocities. The X-wire is concluded to furnish more accurate results for the turbulent shear stress than a multioriented single-wire technique.

Lilley, D. G.↗
NASA NTRS1984

Influence of aluminum oxide film on thermocompression bonding of gold wire to evaporated aluminum film

The influence of Al surface condition on the thermocompression bonding of Au wires to Al electrodes for integrated electric circuits was studied. Au wires were connected to Al electrodes by nail-head bonding after various Al surface treatments. Bonding was evaluated by measuring the wire pull strength and fraction of the number of failures at Au-Al bonds to the total number of failures. Dependence of the fraction on applied load was derived theoretically with a parameter named critical load to take into consideration the differences in Al surface condition. The relation also held explicately for various surface treatments. Characterization of the Al surface was carried out by electron microscopy for chemical analysis.

Iwata, S.↗
NASA NTRS1986

Some influences of approximate values for velocity, density and total temperature sensitivities on hot wire anemometer results

There is a renewed interest in hot wire anemometry at transonic speeds. Recent results were published which indicate that at transonic speeds a heated wire is sensitive only to mass flow and total temperature, results similar to those obtained for supersonic flows. Other results were obtained to show that the sensitivity is a function of velocity, density, and total temperature, results in agreement with many of those obtained in the 1950s. An analysis of anemometry results was made to evaluate possible errors when various assumptions were made concerning the sensitivity of a heated wire to fluid flow variables.

Stainback, P. C.↗
NASA NTRS1985

A review of hot wire anemometry in transonic flows

The present paper provides a review of hot wire anemometry for compressible flows, giving particular attention to the transonic flow problem. It is pointed out that the first and most important definitive work in hot wire anemometry for compressible flows was reported by Kovasznay (1953). The existence of three independent fluctuating modes in compressible flows for small perturbations was found, taking into account the vorticity mode, the entropy mode, and the sound-wave mode. A review of Kovasznays' method for supersonic flows is also presented, and advances reported by Markovin (1956) are examined. Attention is given to experiments conducted by Horstman and Rose (1977), a general solution to the hot wire problem at transonic conditions sought by Stainback et al. (1983), and some apparent problems.

Stainback, P. C.↗
NASA NTRS1987

Supports for Wires Soldered to Pins

Stress concentrations reduced by reorienting wires. New solder-joint configuration provides support for part of wire most susceptible to damage from handling or vibration part next to solder joint. Reversal of wire and heat-shrinkable tubing reduce stress in this region.

Hill, Arthur J.↗
NASA NTRS1987

Initial investigations into the damping characteristics of wire rope vibration isolators

Passive dampers composed of coils of multi-strand wire rope are investigated. Analytical results range from those produced by complex NASTRAN models to those of a Coulomb damping model with variable friction force. The latter agrees well with experiment. The Coulomb model is also utilized to generate hysteresis loops. Various other models related to early experimental investigations are described. Significant closed-form static solutions for physical properties of single-and multi-strand wire ropes are developed for certain specific geometries and loading conditions. NASTRAN models concentrate on model generation and mode shapes of 2-strand and 7-strand straight wire ropes with interfacial forces.

Cutchins, M. A.↗