Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC ATTENUATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

High-intensity sound in air saturated fibrous bulk porous materials

The interaction high-intensity sound with bulk porous materials in porous materials including Kevlar 29 is reported. The nonlinear behavior of the materials was described by dc flow resistivity tests. Then acoustic propagation and reflection were measured and small signal broadband measurements of phase speed and attenuation were carried out. High-intensity tests were made with 1, 2, and 3 kHz tone bursts to measure harmonic generation and extra attenuation of the fundamental. Small signal standing wave tests measured impedence between 0.1 and 3.5 kHz. High level tests with single cycle tone bursts at 1 to 4 kHz show that impedance increases with intensity. A theoretical analysis is presented for high-porosity, rigid-frame, isothermal materials. One dimensional equations of motion are derived and solved by perturbation. The experiments show that there is excess attenuation of the fundamental component and in some cases a close approach to saturation. A separate theoretical model, developed to explain the excess attenuation, yields predictions that are in good agreement with the measurements. Impedance and attenuation at high intensities are modeled.

Kuntz, H. L., II↗

An Investigation of Two Acoustic Propagation Codes for Three-Dimensional Geometries

The ability to predict fan noise within complex three-dimensional aircraft engine nacelle geometries is a valuable tool in studying low-noise designs. Recent years have seen the development of aeroacoustic propagation codes using various levels of approximation to obtain such a capability. In light of this, it is beneficial to pursue a design paradigm that incorporates the strengths of the various tools. The development of a quasi-3D methodology (Q3D-FEM) at NASA Langley has brought these ideas to mind in relation to the framework of the CDUCT-LaRC acoustic propagation and radiation tool. As more extensive three dimensional codes become available, it would seem appropriate to incorporate these tools into a framework similar to CDUCT-LaRC and use them in a complementary manner. This work focuses on such an approach in beginning the steps toward a systematic assessment of the errors, and hence the trade-offs, involved in the use of these codes. To illustrate this point, CDUCT-LaRC was used to study benchmark hardwall duct problems to quantify errors caused by wave propagation in directions far removed from that defined by the parabolic approximation. Configurations incorporating acoustic treatment were also studied with CDUCT-LaRC and Q3D-FEM. The cases presented show that acoustic treatment diminishes the effects of CDUCT-LaRC phase error as the solutions are attenuated. The results of the Q3D-FEM were very promising and matched the analytic solution very well. Overall, these tests were meant to serve as a step toward the systematic study of errors inherent in the propagation module of CDUCT-LaRC, as well as an initial test of the higher fidelity Q3D-FEM code.

Nark, D. M.↗

Acoustic Data Processing and Transient Signal Analysis for the Hybrid Wing Body 14- by 22-Foot Subsonic Wind Tunnel Test

An advanced vehicle concept, the HWB N2A-EXTE aircraft design, was tested in NASA Langley's 14- by 22-Foot Subsonic Wind Tunnel to study its acoustic characteristics for var- ious propulsion system installation and airframe con gurations. A signi cant upgrade to existing data processing systems was implemented, with a focus on portability and a re- duction in turnaround time. These requirements were met by updating codes originally written for a cluster environment and transferring them to a local workstation while en- abling GPU computing. Post-test, additional processing of the time series was required to remove transient hydrodynamic gusts from some of the microphone time series. A novel automated procedure was developed to analyze and reject contaminated blocks of data, under the assumption that the desired acoustic signal of interest was a band-limited sta- tionary random process, and of lower variance than the hydrodynamic contamination. The procedure is shown to successfully identify and remove contaminated blocks of data and retain the desired acoustic signal. Additional corrections to the data, mainly background subtraction, shear layer refraction calculations, atmospheric attenuation and microphone directivity corrections, were all necessary for initial analysis and noise assessments. These were implemented for the post-processing of spectral data, and are shown to behave as expected.

Bahr, Christopher J.↗

WE-D-BRF-02: Acoustic Signal From the Bragg Peak for Range Verification in Proton Therapy

Purpose: Range verification in ion beam therapy relies to date on nuclear imaging techniques which require complex and costly detector systems. A different approach is the detection of thermoacoustic signals that are generated due to localized energy loss of ion beams. Aim of this work is to study the feasibility of determining the ion range with sub-mm accuracy by use of high frequency ultrasonic (US) transducers and to image the Bragg peak by tomography. Methods: A water phantom was irradiated by a pulsed 20 MeV proton beam with varying pulse intensity, length and repetition rate. The acoustic signal of single proton pulses was measured by different PZT-based US detectors (3.5 MHz and 10 MHz central frequencies). For tomography a 64 channel US detector array was used and moved along the ion track by a remotely controlled motor stage. Results: A clear signal of the Bragg peak was visible for an energy deposition as low as 10{sup 12} eV. The signal amplitude showed a linear increase with particle number per pulse and thus, dose. Range measurements were reproducible within +/− 20 micrometer and agreed well with Geant4 simulations. The tomographic reconstruction does not only allow to measure the ion range but also the beam spot size at the Bragg peak position. Conclusion: Range verification by acoustic means is a promising new technique for treatment modalities where the tumor can be localized by US imaging. Further improvement of sensitivity is required to account for higher attenuation of the US signal in tissue, as well as lower energy density in the Bragg peak in realistic treatment cases due to higher particle energy and larger spot sizes. Nevertheless, the acoustic range verification approach could offer the possibility of combining anatomical US imaging with Bragg Peak imaging in the near future. The work was funded by the DFG cluster of excellence Munich Centre for Advanced Photonics (MAP)

60 APPLIED LIFE SCIENCES↗

A Theoretical and Experimental Study of Acoustic Propagation in Multisectioned Circular Ducts

The propagation of plane waves and higher order acoustic modes in a circular multisectioned duct was studied. A unique source array consisting of two concentric rings of sources, providing phase and amplitude control in the radial, as well as circumferential direction, was developed to generate plane waves and both spinning and nonspinning higher order modes. Measurements of attenuation and radial mode shapes were taken with finite length liners inserted between the hard wall sections of an anechoically terminated duct. Materials tested as liners included a glass fiber material and both sintered fiber metals and perforated sheet metals with a honeycomb backing. The fundamental acoustic properties of these materials were studied with emphasis on the attenuation of sound by the liners and the determination of local versus extended reaction behavior for the boundary condition. A search technique was developed to find the complex eigenvalues for a liner under the assumption of a locally reacting boundary condition.

Wyerman, B. R.↗

Inlet noise suppressor design method based upon the distribution of acoustic power with mode cutoff ratio

A liner design for noise suppressors with outer wall treatment such as in an engine inlet is presented which potentially circumvents the problems of resolution in modal measurement. The method is based on the fact that the modal optimum impedance and the maximum possible sound power attenuation at this optimum can be expressed as functions of cutoff ratio alone. Modes with similar cutoff ratios propagate similarly in the duct and in addition propagate similarly to the far field. Thus there is no need to determine the acoustic power carried by these modes individually, and they can be grouped together as one entity. With the optimum impedance and maximum attenuation specified as functions of cutoff ratio, the off-optimum liner performance can be estimated using an approximate attenuation equation.

Rice, E. J.↗

Design and Acoustic Efficacy of a Broadband Liner for the Inlet of the DGEN Aero-Propulsion Research Turbofan

Advanced fan designs (including higher bypass ratios) and shorter engine nacelles have highlighted a need for increased fan noise reduction over a broader frequency range. With these observations in mind, an acoustic liner optimization process has been developed to achieve improved broadband liner designs. A series of advanced liner design studies at increasing technology readiness levels have been conducted as the overall optimization methodology has been enhanced. As part of the analysis, the overall design and evaluation capability was extended such that external observer locations may be included in the optimization process. This enhancement will provide a much wider design space in designing advanced broadband liners. In this work, further validation was pursued through the fabrication and testing of two liner designs for the NASA Glenn DGEN Aero-propulsion Research Turbofan (DART). The DART was used to document the efficacy of acoustic liners installed in the inlet of the DGEN380. An advanced Multi-Degree of Freedom Liner was designed, fabricated, and tested, along with a traditional Single-Degree-of-Freedom Liner, and those results compared to a hardwall baseline inlet. Farfield acoustic data were acquired from and external array, evaluated and reported herein terms of overall, broadband, and tonal components of the insertion loss. The predicted attenuation results generally matched expected trends of the measured data for the conditions considered.

Liners↗

Multiphenomenology explosion monitoring (MultiPEM): a general framework for data interpretation and yield estimation

SUMMARY An underground nuclear explosion (UNE) couples mechanical energy into crustal rock, which propagates as seismic and acoustic waves. These different physical phenomena transport, by different pathways, to standoff detectors at varying distances. The transport pathways attenuate the original signal but in different ways. Enabled by correct statistical weighting, signal attenuation models can be used to combine these disparate sensor data to estimate the yield of an UNE. Contemporaneous statistical models, used in yield estimation, can be improved with an advanced partition of error for these physical signal propagation models. We present an advanced multivariate approach to error modelling of multiphenomenology physical signatures. In addition to measurement error, our error model represents physical model biases as random with a physics-based covariance structure. To illustrate this proposed framework, we demonstrate the estimation of explosion yield using openly available seismic and acoustic data from chemical single-point explosions.

Williams, Brian J.↗

Characterizing the Effects of Two Ground-based Outdoor Microphone Configurations

Multiple International and Federal regulations stipulate the acquisition of aircraft noise shall be conducted using inverted pressure microphones over a round ground board. These ground boards are used to provide an acoustically hard reflecting surface, limiting the effects of the potentially absorptive ground local to the test location. The microphone location is also specified to be offset from the center of the board to limit the effects of acoustic diffraction off the board edge. In order to determine the effects of the ground board on the measured acoustic signal, a comprehensive measurement campaign was undertaken at NASA Langley Research Center. The experimental setup included multiple ground board configurations placed on top of a sand pit, in an otherwise anechoic chamber. Ground board configurations included a microphone inverted and offset over the round ground board and a microphone offset and flush mounted in the ground board.White noise was then used to investigate the ground board effects on the recorded signal. Normal impedance measurements were also acquired to determine the reflection coefficients of the sand and ground boards. Experimental results are discussed, along with implications for future research and development.Results indicate that both microphone configurations perform adequately up to 10 kHz. When the ground substrate is a soft material and the sound comes in at angles near grazing incidence the sound energy is attenuated above 1 kHz. Additionally, the plastic material used to construct the ground boards was found to be acoustically hard between 0.1 –3.0 kHz, and likely extending to higher frequencies.

Mark C. Anderson↗

Temperature Fields in Soft Tissue during LPUS Treatment: Numerical Prediction and Experiment Results

Recent research has shown that beneficial therapeutic effects in soft tissues can be induced by the low power ultrasound (LPUS). For example, increasing of cells immunity to stress (among others thermal stress) can be obtained through the enhanced heat shock proteins (Hsp) expression induced by the low intensity ultrasound. The possibility to control the Hsp expression enhancement in soft tissues in vivo stimulated by ultrasound can be the potential new therapeutic approach to the neurodegenerative diseases which utilizes the known feature of cells to increase their immunity to stresses through the Hsp expression enhancement. The controlling of the Hsp expression enhancement by adjusting of exposure level to ultrasound energy would allow to evaluate and optimize the ultrasound-mediated treatment efficiency. Ultrasonic regimes are controlled by adjusting the pulsed ultrasound waves intensity, frequency, duration, duty cycle and exposure time. Our objective was to develop the numerical model capable of predicting in space and time temperature fields induced by a circular focused transducer generating tone bursts in multilayer nonlinear attenuating media and to compare the numerically calculated results with the experimental data in vitro. The acoustic pressure field in multilayer biological media was calculated using our original numerical solver. For prediction of temperature fields the Pennes' bio-heat transfer equation was employed. Temperature field measurements in vitro were carried out in a fresh rat liver using the 15 mm diameter, 25 mm focal length and 2 MHz central frequency transducer generating tone bursts with the spatial peak temporal average acoustic intensity varied between 0.325 and 1.95 W/cm{sup 2}, duration varied from 20 to 500 cycles at the same 20% duty cycle and the exposure time varied up to 20 minutes. The measurement data were compared with numerical simulation results obtained under experimental boundary conditions. Good agreement between the theoretical and measurement results for all cases considered has verified the validity and accuracy of our numerical model. Quantitative analysis of the obtained results enabled to find how the ultrasound-induced temperature rises in the rat liver could be controlled by adjusting the source parameters and exposure time.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Effects of wave damping and finite perpendicular scale on three-dimensional Alfvén wave parametric decay in low-beta plasmas

Shear Alfvén wave parametric decay instability (PDI) provides a potential path toward significant wave dissipation and plasma heating. However, fundamental questions regarding how PDI is excited in a realistic three-dimensional (3D) open system and how the finite perpendicular wave scale—as found in both laboratory and space plasmas—affects the excitation remain poorly understood. Here, we present the first 3D, open-boundary, hybrid kinetic-fluid simulations of kinetic Alfvén wave PDI in low-beta plasmas. Key findings are that the PDI excitation is strongly limited by the wave damping present, including electron–ion collisional damping (represented by a constant resistivity) and geometrical attenuation associated with the finite-scale Alfvén wave, and ion Landau damping of the child acoustic wave. The perpendicular wave scale alone, however, plays no discernible role: waves of different perpendicular scales exhibit similar instability excitation as long as the magnitude of the parallel ponderomotive force remains unchanged. These findings are corroborated by theoretical analysis and estimates. This new understanding of 3D kinetic Alfvén wave PDI physics is essential for laboratory study of the basic plasma process and may also aid future evaluation of the relevance/role of PDI in low-beta space plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analysis of MINIE2013 Explosion Air-Blast Data

We report analysis of air-blast overpressure measurements from the MINIE2013 explosive experiments. The MINIE2013 experiment involved a series of nearly 70 near-surface (height-ofburst, HOB, ranging from -1 to +4 m) low-yield (W=2-20 kg TNT equivalent) chemical highexplosives tests that were recorded at local distances (230 m – 28.5 km). Many of the W and HOB combinations were repeated, allowing for quantification of the variability in air-blast features and corresponding yield estimates. We measured canonical signal features (peak overpressure, impulse per unit area, and positive pulse duration) from the air-blast data and compared these to existing air-blast models. Peak overpressure measurements showed good agreement with the models at close ranges but tended to attenuate more rapidly at longer range (~ 1 km), which is likely caused by upward refraction of acoustic waves due to a negative vertical gradient of sound speed. We estimated yields of the MINIE2013 explosions using the Integrated Yield Determination Tool (IYDT). Errors of the estimated yields were on average within 30% of the reported yields, and there were no significant differences in the accuracy of the IYDT predictions grouped by yield. IYDT estimates tend to be lower than ground truth yields, possibly because of reduced overpressure amplitudes by upward refraction. Finally, we report preliminary results on a development of a new parameterized air-blast waveform.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Acoustic results obtained with upper-surface-blowing lift augmentation systems

The noise caused by the interaction of the jet exhaust and a wing was measured under static conditions for several versions of a small-scale STOL engine-over-the-wing configuration. Three basic nozzles were used in the tests; a circular nozzle, a 5:1 aspect ratio slot nozzle and a 10:1 aspect ratio slot nozzle. Various flow attachment devices were included in the study. The wing included a flap that could be positioned for nominal takeoff or approach flap settings. Far field noise data are presented for the flyover mode. The data are discussed in terms of sound power and sound pressure spectra. Implications of extending the small-scale model acoustic data to full-scale aircraft are discussed briefly and indicate a sizeable flyover noise attenuation may be achieved due to shielding by the wing.

Vonglahn, U. H.↗

On the interaction of a sound pulse with the shear layer of an axisymmetric jet

The behavior of a sound pulse from a simulated source in a jet is investigated both experimentally and numerically. Both approaches show that in the low and medium frequencies the far field acoustic power exhibits and marked amplification as the flow velocity increases. Experimentally this changes to an attenuation at the higher frequencies which cannot be computed by the numerical model. This amplification is traced to shear noise terms which trigger the instability waves that are inherent within the flow.

Maestrello, L.↗

Noise transmission of double wall composite shells

This paper describes analytical studies of noise transmission of double wall laminated composite cylindrical shells of finite extent. The main objective is to estimate structureborne noise generated by the concentrated random forces. The theoretical solutions of the governing acoustic-structural equations are obtained utilizing modal decomposition. Results indicate that from the viewpoint of noise attenuation the composite shell does not seem to offer advantage over an aluminum shell. However, the orientation of the fibers and the material characteristics of the soft viscoelastic core can be tailored to meet the specific needs of noise attenuation.

Vaicaitis, R.↗

The acoustic and instability waves of jets confined inside an acoustically lined rectangular duct

An analysis of linear wave modes associated with supersonic jets confined inside an acoustically lined rectangular duct is presented. Mathematical formulations are given for the vortex-sheet model and continuous mean flow model of the jet flow profiles. Detailed dispersion relations of these waves in a two-dimensional confined jet as well as an unconfined free jet are computed. Effects of the confining duct and the liners on the jet instability and acoustic waves are studied numerically. It is found that the effect of the liners is to attenuate waves that have supersonic phase velocities relative to the ambient flow. Numerical results also show that the growth rates of the instability waves could be reduced significantly by the use of liners. In addition, it is found that the upstream propagating neutral waves of an unconfined jet could become attenuated when the jet is confined.

Hu, Fang Q.↗

Collaboration with Williams International to Demonstrate the Characteristics of a Foam-Metal-Liner Installed Over-the-Rotor of a Turbofan Engine

A Williams International FJ44-3A 3000-lb thrust class turbofan engine was used as a demonstrator for foam-metal liner installed in close proximity to the fan. Two foam metal liner designs were tested and compared to the hardwall. Traditional Single-Degree-of-Freedom liner designs were also evaluated to provide a comparison. Normalized information on farfield acoustics is presented in this paper. The results show that up to 5 dB PWL overall attenuation was achieved in the forward quadrant. In general, the foam-metal liners performed better when the fan tip speed was below sonic.

Sutliff, Daniel↗

Active Control of Liner Impedance by Varying Perforate Orifice Geometry

The present work explored the feasibility of controlling the acoustic impedance of a resonant type acoustic liner. This was accomplished by translating one perforate over another of the same porosity creating a totally new perforate that had an intermediate porosity. This type of adjustable perforate created a variable orifice perforate whose orifices were non-circular. The key objective of the present study was to quantify, the degree of attenuation control that can be achieved by applying such a concept to the buried septum in a two-degree-of-freedom (2DOF) acoustic liner. An additional objective was to examine the adequacy of the existing impedance models to explain the behavior of the unique orifice shapes that result from the proposed silding perforate concept. Different orifice shapes with equivalent area were also examined to determine if highly non-circular orifices had a significant impact on the impedance.

Ahuji, K. K.↗