SEARCH · Search NASA

Results for “AXIAL RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Advanced Compressors for CO2-Based Power Cycles and Energy

Pumped thermal energy storage (PTES) is a cost-effective method for grid-scale, long-duration electrical energy storage (LDES). PTES uses a heat pump cycle to transfer thermal energy from a low temperature reservoir (LTR) to a high temperature reservoir (HTR), later using a heat engine cycle to reverse the process. A key component of the PTES system, the heat pump compressor, represents a significant driver to the cost, performance and operating characteristics of the PTES system. For grid-scale charging (>100 MW), traditional compressor scaling charts indicate that the operating conditions needed would be best served by a multistage axial compressor. While frame gas turbine compressors at these power ratings exist and operate at higher pressure ratios than needed for the CO2 PTES system, the inlet pressure and fluid density of this application exceed experience values. A conceptual design of a large-scale CO2 axial compressor was completed, including mean-line estimates of the compressor performance at full power conditions. The results of the conceptual design were used to refine the PTES cycle design, and updated operating conditions provided for further aero design optimization. A roughly one third scale of the first three stages of the 100 MW compressor was designed, built, and tested at relevant PTES charging conditions. Results of this test program are compared against high-resolution computational fluid dynamics models.

Compressor Heat↗

NASA NTRS2000

Assessment of Internal Fabric of Particulate Materials

Particle arrangement and distribution within a soil matrix has long been recognized as having significant influence on the mechanical behavior of cohesionless soils. It is well known that two soil specimens having the same grain type (e.g., quartz, feldspar, etc.), same grain size distribution and relative density (or void ratio) can display completely different mechanical behavior. Because of the different fabric configurations in the otherwise similar specimens, they are likely to have different mechanical properties such as stress-strain response, anisotropy, dilatancy, etc. Soil Fabric is defined as the arrangement of particles, particle groups and associated pore space. In the literature, fabric analysis techniques are mainly classified as destructive (e.g., specimen stabilization, thin-sectioning, and microscopy), and nondestructive techniques (e.g., magnetic resonance imaging, ultrasonic testing, x-ray radiography, and computed tomography). Quantifying the void ratio and its distribution is the main parameter used to describe the fabric of particulate materials. This paper presents a comprehensive literature review of fabric analysis techniques applied to particulate materials. In addition, the results of a comprehensive investigation to quantify void ratio of sand specimens will be presented and discussed. The sand used in the experiments in a natural, uniform rounded to sub-rounded silica sand known as F-75 banding sand with mean particle size of 0.22 mm. Uniform specimens and specimens subjected to different axial-strain levels tested under triaxial and biaxial conditions are examined to evaluate void ratio evolution and its distribution using destructive thin-sectioning and nondestructive Computed Tomography (CT) techniques. Details of a new innovative polygon generation technique called Voronoi tessellation used to quantify void ratio of microscopic images of sand grains will be presented and compared to classical Oda's method. Finally, frequency distribution of void ratio calculated using CT analysis will be presented and discussed.

Alshibi, Khalid A.↗

DOE OSTI2024

Vortex bursting and associated twist dynamics on helical vortex tubes and vortex rings

The interaction of opposite-signed twist waves on vortex tubes can lead to vortex bursting, a process where the core expands into a double ring-like structure with strong swirling flows. Previous works have studied vortex bursting on rectilinear vortices by axially perturbing the initial core size to generate the twist waves, and observed largely axisymmetric bursting dynamics. In this work, we numerically study bursting on vortical structures with curved centrelines, analysing the interaction between the centreline dynamics, twist wave generation and propagation, and vortex bursting. We focus on axially perturbed helical vortex tubes with small radius-to-pitch ratios up to$0.0625$, as well as vortex rings with a large radius-to-core size ratio$10$, both at a circulation-based Reynolds number$5000$. The results show that though the initial twist wave propagation speeds are relatively unaffected by the curvature and torsion of the centreline, the bursting process is altered significantly compared with rectilinear vortices. The self-induced rotation of the centreline of the helical tube induces a non-axisymmetric distortion of the bursting structure, which rapidly breaks up the vortex core into small-scale helical structures. A similar destabilization of the bursting structure also occurs on vortex rings. The enstrophy increase and accelerated energy decay associated with bursting are predominantly determined by the twist wave strength, rather than the curvature and torsion of the centreline. Combined, our findings imply that bursting could play an important role in transferring and dissipating energy of vortical structures in wakes, and turbulent flows in general.

Mechanics↗

NASA NTRS1973

Experimental investigation of combustor effects on rocket thrust chamber performance

The results are reported of a program to develop special instrumentation systems and engine hardware, conduct tests using LOX/GH2 propellants wherein radial mixtures ratio stratification was controlled, and subsequently compare the results of four selected tests with the predictions of the JANNAF performance-prediction computer programs. During the experiments, the overall propellant mixture ratio was varied from 4.4 to 6.6, while the mixture ratios in the core and outer zone were varied from 5.7 to 8.8 and from 3.7 to 7.2, respectively. A nominal 10 percent of the total fuel flow was used as boundary layer collant in a majority of the firings. Nominal chamber pressure was either 225 or 250 psia, with nozzle expansion ratios of either 25:1 or 4:1. Measurements of the axial chamber pressure and wall heat flux profiles, together with samples of the exhaust gas, were obtained. The corrected experimental specific impulse and characteristic exhaust velocity efficiencies were approximately 97.5 and 98.5 percent, respectively.

Nurick, W. H.↗

NASA NTRS1974

Sound radiation from a subsonic rotor subjected to turbulence

The broadband sound radiated by a subsonic rotor subjected to turbulence in the approach stream has been analyzed. The power spectral density of the sound intensity has been found to depend on a characteristic time scale-namely, the integral scale of the turbulence divided by the axial flow velocity-as well as several length-scale ratios. These consist of the ratio of the integral scale to the acoustic wavelength, rotor radius, and blade chord. Due to the simplified model chosen, only a limited number of cascade parameters appear. Limited comparisons with experimental data indicate good agreement with predicted values.

Sevik, M.↗

NASA NTRS1981

Rotor wake characteristics relevant to rotor-stator interaction noise generation

Mean and turbulent wake properties at three axial locations behind the rotor of an aerodynamically loaded 1.2 pressure ratio fan were measured using a stationary cross film anemometer in an anechoic wind tunnel. Wake characteristics at four radial immersions across the duct at four different fan speeds were determined utilizing a signal enhancement technique. The shapes of the waveforms of the mean rotor relative and mean upwash velocities were shown to change significantly across the span of the blades. In addition, an increase in fan rotational speed caused an increase in the maximum wake turbulence intensity levels near the hub and tip. Spectral analysis was used to described the complex nature of the rotor wake.

Shaw, L. M.↗

NASA NTRS1981

Rotor wake characteristics relevant to rotor-stator interaction noise generation

Mean and turbulence wake properties at three axial locations behind the rotor of an aerodynamically loaded 1.2 pressure ratio fan were measured using a stationary cross film anemometer in an anechoic wind tunnel. Wake characteristics at four radial immersions across the duct at four different fan speeds were determined utilizing a signal enhancement technique. The shapes of the waveforms of the mean rotor relative and mean upwash velocities were shown to change significantly across the span of the blades. In addition, an increase in fan rotational speed caused an increase in the maximum wake turbulence intensity levels near the hub and tip. Spectral analysis was used to describe the complex nature of the rotor wake.

Shaw, L. M.↗

NASA NTRS1983

Turbulence measurements in a complex plowfield using a crossed hot-wire

Turbulence was quantified in complex axisymmetric, nonreacting, nonswirling flowfields using a crossed hot-wire anemometer. Mean velocity, turbulence intensities, turbulent viscosity, and Reynolds tree were measured in round free jet and confined jet flowfields. The confined jet, a model of an axisymmetric can combustor, had an expansion ratio D/d=2, an expansion angle of 90 deg, and an axial location increments of 0.5 diameters. The confined jet was studied with and without a contraction nozzle. Free jet measurements validated the experimental technique and data reduction. Results show good agreement with those of previous research. Measurements in the confined jet indicate that the cross hot-wire used cannot handle axial flow reversal and the experimental technique is inadequate for measuring time-mean radial velocity. Other quantities show a high level of comparability.

Mckillop, B. E.↗

NASA NTRS1985

Review of the development of small- and medium-capacity gas turbines at the Motoren- und Turbinen Union

Small- and medium-capacity gas turbines under development for turboprop aircraft and helicopter, as well as for armored and commercial vehicle propulsion, are discussed. Design problems related to axial turbines, ceramic components, regenerative gas turbines, and the optimal expansion ratios for turbines with capacities from 250 to greater than 800 kW are considered; in addition, combustion chamber technology is mentioned. Prototype gas turbines with capacities of 500 to 600 kW or 800 to 1800 kW are described.

Heilmann, W.↗

NASA NTRS1951

Investigation of Turbulent Flow in a Two-Dimensional Channel

A detailed exploration of the field of mean and fluctuating quantities in a two-dimensional turbulent channel flow is presented. The measurements were repeated at three Reynolds numbers, 12,300, 30,800, and 61,600, based on the half width of the channel and the maximum mean velocity. A channel of 5-inch width and 12:1 aspect ratio was used for the investigation. Mean-speed and axial-fluctuation measurements were made well within the laminar sublayer. The semitheoretical predictions concerning the extent of the laminar sublayer were confirmed. The distribution of the velocity fluctuations in the direction of mean flow u' shows that the influence of the viscosity extends farther from the wall than indicated by the mean velocity profile, the region of influence being approximately four times as wide.

Laufer, John↗

NASA NTRS2000

Heat Transfer and Flow on the Squealer Tip of a Gas Turbine Blade

Experimental investigations are performed to measure the detailed heat transfer coefficient and static pressure distributions on the squealer tip of a gas turbine blade in a five-bladed stationary linear cascade. The blade is a 2-dimensional model of a modem first stage gas turbine rotor blade with a blade tip profile of a GE-E(sup 3) aircraft gas turbine engine rotor blade. A squealer (recessed) tip with a 3.77% recess is considered here. The data on the squealer tip are also compared with a flat tip case. All measurements are made at three different tip gap clearances of about 1%, 1.5%, and 2.5% of the blade span. Two different turbulence intensities of 6.1% and 9.7% at the cascade inlet are also considered for heat transfer measurements. Static pressure measurements are made in the mid-span and near-tip regions, as well as on the shroud surface opposite to the blade tip surface. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and an exit Reynolds number based on the axial chord of 1.1 x 10(exp 6). A transient liquid crystal technique is used to measure the heat transfer coefficients. Results show that the heat transfer coefficient on the cavity surface and rim increases with an increase in tip clearance. 'Me heat transfer coefficient on the rim is higher than the cavity surface. The cavity surface has a higher heat transfer coefficient near the leading edge region than the trailing edge region. The heat transfer coefficient on the pressure side rim and trailing edge region is higher at a higher turbulence intensity level of 9.7% over 6.1 % case. However, no significant difference in local heat transfer coefficient is observed inside the cavity and the suction side rim for the two turbulence intensities. The squealer tip blade provides a lower overall heat transfer coefficient when compared to the flat tip blade.

Azad, Gm S.↗

NASA NTRS1945

Calculation of Centrally Loaded Thin-Walled Columns Above the Buckling Limit

When thin-walled columns formed from flanged sheet, such as used in airplane construction, are subjected to axial load, their behavior at failure varies according to the slenderness ratio. On long columns the axis deflects laterally while the cross section form is maintained; buckling results. The respective breaking load in the elastic range is computed by Euler's formula and for the plastic range by the Engesser- Karman formula. Its magnitude is essentially dependent upon the length. On intermediate length columns, especially where open sections are concerned, the cross section is distorted while the cross section form is preserved; twisting failure results. The buckling load in twisting is calculated according to Wagner and Kappus. On short columns the straight walls of low-bending resistance that form the column are deflected at the same time that the cross section form changes - buckling occurs without immediate failure. Then the buckling load of the total section computable from the buckling loads of the section walls is not the ultimate load; quite often, especially on thin-walled sections, it lies considerably higher and is secured by tests. Both loads, the buckling and the ultimate load are only in a small measure dependent upon length. The present report is an attempt to theoretically investigate the behavior of such short, thin-walled columns above the buckling load with the conventional calculating methods.

Reinitzhuber, F.↗

NASA NTRS1974

Jet noise from co-axial nozzles over a wide range of geometric and flow parameters

Free field pure jet noise data were taken for a large range of coaxial nozzle configurations. The core nozzles were circular (1 to 4 in. diameter) and plug types. The fan to core area ratio varied from 0.7 to 43.5, while the velocity ratio typically varied from 0 to 1. For most cases the two nozzles were coplanar but large axial extensions of either nozzle were also tested. Correlation of the data resulted in a simple procedure for estimating ambient temperature subsonic coaxial jet noise spectra over a wide range of geometric and flow parameters.

Olsen, W.↗

NASA NTRSDate not supplied

Advances in Integrally Formed Metallic Structures

NASA Langley Research Center (LaRC) is applying flow forming technology to aerospace aluminum alloys for the manufacture of integrally stiffened cylinders that meet aircraft fuselage or launch vehicle specifications. High-strength 2xxx series alloys, in various temper/product form conditions, are being compared with medium-strength, very formable AA 6061 as the benchmark. Screening of candidate materials traditionally relies on empirical forming trials, but more recently on metrics derived from constant nominal strain rate tensile testing. In this work, the established hierarchy of formability metrics is adopted as the baseline; tensile area reduction, work hardening exponent, and modulus of resilience. The suite of metrics can be expanded based on phenomenological and mechanistic considerations of plastic flow instabilities to incorporate anisotropy ratio, rate of work hardening, and dynamic strain aging effects. Separate research thrusts at LaRC are aimed at formulating a protocol for scalable production of fully formed, defect-free components: 1) quantifying the extended set of formability metrics from constant and jump strain rate tensile tests with digital image correlation (DIC); 2) using statistically designed experiments on a vertical spin/flow forming facility (WF VUD-600®) to isolate the effect of convenient process variables, such as axial feed rate and thickness reduction; and 3) predicting the effect of feed ratio (roller translation relative to mandrel rotation speeds) on material response via process modeling using the DEFORM® simulation software. Current results will be discussed in terms of correlating intrinsic material properties with the bulk workability characteristics to successfully fabricate cylinders with complex cross-sections.

Aluminum↗

NASA NTRS1974

Aerodynamic performance of 0.5 meter-diameter, 337 meter-per-second tip speed, 1.5 pressure-ratio, single-stage fan designed for low noise aircraft engines

Overall and blade-element aerodynamic performance of a 0.271-scale model of QF-1 are presented, examined, and then compared and evaluated with that from similar low noise fan stage designs. The tests cover a wide range of speeds and weight flows along with variations in stator setting angle and stator axial spacing from the rotor. At design speed with stator at design setting angle and a fixed distance between stage measuring stations, there were no significant effects of increasing the axial spacing between rotor stator from 1.0 to 3.5 rotor chords on stage overall pressure ratio, efficiency or stall margin.

Gelder, T. F.↗

NASA NTRS1998

Elastic Buckling of Laminated Plates Under Varying Axial Stresses

The elastic buckling load of simply supported rectangular composite plates subjected to a second degree parabolic variation of axial stresses in the longitudinal direction is calculated using analytical methods. The variation of axial stresses is equilibrated by nonuniform shear stresses along the plate edges and transverse normal stresses. Numerical results are reported for three different cases: (1) orthotropic plates, (2) symmetrically laminated plates with multiple generally orthotropic layers exhibiting coupling between normal moments and twist, and twisting moment and normal curvatures, and (3) unsymmetrically laminated plates. Rayleigh-Ritz method is used to calculate the buckling load. An approximate solution using "reduced bending stiffness" is adopted for unsymmetrically laminated plates. The influence of the aspect ratio is examined, and the results are compared with plates subjected to uniform axial stresses.

Badir, A.↗

NASA NTRSDate not supplied

Effect of Injection Dynamics on Wave Propagation in a Linear Detonation Combustor

Injector response to self-excited and sustained detonation wave propagation in an optically-accessible nonpremixed natural gas-oxygen linear detonation combustor is investigated. 100 kHz measurements of planar laser induced fluorescence (PLIF) of trace quantities of acetone injected into the fuel supply and simultaneous OH∗ chemiluminescence measurements were used to correlate the effect on injection dynamics on detonation wave structure and propagation. Measurements over a range of equivalence ratios (0.61-1.48) revealed wave propagation through regions of high fuel stratification in the axial and transverse direction of reactant injection. Consequently, the propagation of the detonation wave along the channel is through a flow-field with significant variation in fuel mass fraction, reactivity, and sound speeds. At lean conditions, wave propagation frequency is generally lower (∼6 kHz) resulting in longer time between wave passages for mixing and pre-heat resulting in steeper detonation wave-fronts anchored near the injector exit plane. Conversely, at rich equivalence ratios the wave frequency is higher (∼10 kHz) resulting in shorter intra-cycle period for reactant fill and mixing resulting waves lifted from the injection plane that are more compact. Higher chemiluminescence intensity in the post-wave region with deflagrative combustion is observed in these cases. Phase averaged representation of the acetone-PLIF measurements indicate that the fraction of time between wave passages available for reactant fill, mixing and pre-heat is consistent across all equivalence ratios.

Propulsion↗

NASA NTRSDate not supplied

Effect of Injection Dynamics on Detonation Wave Propagation in a Linear Detonation Combustor

Propulsion↗