Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Recent Dynamic Measurements and Considerations for Aerodynamic Modeling of Fighter Airplane Configurations

As airplane designs have trended toward the expansion of flight envelopes into the high angle of attack and high angular rate regimes, concerns regarding modeling the complex unsteady aerodynamics for simulation have arisen. Most current modeling methods still rely on traditional body axis damping coefficients that are measured using techniques which were intended for relatively benign flight conditions. This paper presents recent wind tunnel results obtained during large-amplitude pitch, roll and yaw testing of several fighter airplane configurations. A review of the similitude requirements for applying sub-scale test results to full-scale conditions is presented. Data is then shown to be a strong function of Strouhal number - both the traditional damping terms, but also the associated static stability terms. Additionally, large effects of sideslip are seen in the damping parameter that should be included in simulation math models. Finally, an example of the inclusion of frequency effects on the data in a simulation is shown.

Brandon, Jay M.↗

Aerodynamic Characterization of New Parachute Configurations for Low-Density Deceleration

The Low Density Supersonic Decelerator project performed a wind tunnel experiment on the structural design and geometric porosity of various sub-scale parachutes in order to inform the design of the 110ft nominal diameter flight test canopy. Thirteen different parachute configurations, including disk-gap-band, ring sail, disk sail, and star sail canopies, were tested at the National Full-scale Aerodynamics Complex 80- by 120-foot Wind Tunnel at NASA Ames Research Center. Canopy drag load, dynamic pressure, and canopy position data were recorded in order to quantify there lative drag performance and stability of the various canopies. Desirable designs would yield increased drag above the disk-gap-band with similar, or improved, stability characteristics. Ring sail parachutes were tested at geometric porosities ranging from 10% to 22% with most of the porosity taken from the shoulder region near the canopy skirt. The disk sail canopy replaced the rings lot portion of the ring sail canopy with a flat circular disk and wastested at geometric porosities ranging from 9% to 19%. The star sail canopy replaced several ringsail gores with solid gores and was tested at 13% geometric porosity. Two disk sail configurations exhibited desirable properties such as an increase of 6-14% in the tangential force coefficient above the DGB with essentially equivalent stability. However, these data are presented with caveats including the inherent differences between wind tunnel and flight behavior and qualitative uncertainty in the aerodynamic coefficients.

parachute↗

A Visual Technique for Determining Qualitative Aerodynamic Heating Rates on Complex Configurations

An experimental investigation was conducted at a test-section Mach number of 4.95 and a stagnation temperature of 400 F to evaluate a visual technique for obtaining qualitative aerodynamic heat-transfer data on complex configurations.This technique utilized a temperature-sensetive paint indicated that this technique was satisfactory for determining qualitative heat-transfer rates on various bodies, some of which exhibited complex flow patterns. The results obtained have been found useful to guide the instrumentation of quantitative heat-transfer models, to supplement quantitative heat-transfer measurements, and to make preliminary heat-transfer studies for new configurations.

P. Calvin Stainback↗

Integrating nonlinear aerodynamic and structural analysis for a complete fighter configuration

The coupling of a nonlinear aerodynamics program with a structural analysis program to include the effects of static aeroelasticity in early preliminary design studies is described. A nonlinear, full potential aerodynamics method with capability to model geometric details of a complete aircraft in supersonic flow is used. The deflections of the lifting surfaces are calculated using an equivalent plate structural representation which can readily accommodate the changes in stiffness and geometric properties required during the preliminary design process. An iterative solution procedure is used to obtain consistent aerodynamic loads and structural deflections at the specified flight conditions. The volume of data transmitted between programs is minimized. The procedure is applied to a complete aircraft and the numerical results illustrate the aeroelastic effects on pressure distribution as well as total forces and moments. During this design study, the thickness distribution of the wing cover skins was initially sized based on rigid loads and subsequently resized under aeroelastic loads. Comparisons are made between these nonlinear aeroelastic results and results obtained from linear aerodynamic methods applied to a rigid shape during conceptual design studies.

Tatum, Kenneth E.↗

Low-speed aerodynamic characteristics of a transport configuration having a 42 deg swept supercritical airfoil wing and three tail height positions

A low speed investigation was conducted in the Langley V/STOL tunnel to define the static stability characteristics of an advanced high subsonic speed transport aircraft model in the cruise configuration (no high lift system). The wing of the model had 42 deg sweep of the quarter chord line, an aspect ratio of 6.78, and supercritical airfoil sections. Three different horizontal tail configurations (high, mid, and low) were investigated on the complete model and for the model with the wing removed in order to assess effects of the wing flow field on the tail contributions to both longitudinal and lateral stability characteristics. All the model configurations investigated were tested over an angle of attack range from approximately -5 to 23 deg. Some model configurations were also tested over an angle of attack range from about 11 to 38 deg in order to explore the aerodynamic characteristics in the deep stall region.

Fournier, P. G.↗

AVION: A detailed report on the preliminary design of a 79-passenger, high-efficiency, commercial transport aircraft

The Avion is the result of an investigation into the preliminary design for a high-efficiency commercial transport aircraft. The Avion is designed to carry 79 passengers and a crew of five through a range of 1,500 nm at 455 kts (M=0.78 at 32,000 ft). It has a gross take-off weight of 77,000 lb and an empty weight of 42,400 lb. Currently there are no American-built aircraft designed to fit the 60 to 90 passenger, short/medium range marketplace. The Avion gathers the premier engineering achievements of flight technology and integrates them into an aircraft which will challenge the current standards of flight efficiency, reliability, and performance. The Avion will increase flight efficiency through reduction of structural weight and the improvement of aerodynamic characteristics and propulsion systems. Its design departs from conventional aircraft design tradition with the incorporation of a three-lifting-surface (or tri-wing) configuration. Further aerodynamic improvements are obtained through modest main wing forward sweeping, variable incidence canards, aerodynamic coupling between the canard and main wing, leading edge extensions, winglets, an aerodynamic tailcone, and a T-tail empennage. The Avion is propelled by propfans, which are one of the most promising developments for raising propulsive efficiencies at high subsonic Mach numbers. Special attention is placed on overall configuration, fuselage layout, performance estimations, component weight estimations, and planform design. Leading U.S. technology promises highly efficient flight for the 21st century; the Avion will fulfill this promise to passenger transport aviation.

Mayfield, William↗

Rotorcraft Technology for HALE Aeroelastic Analysis

Much of technology needed for analysis of HALE nonlinear aeroelastic problems is available from rotorcraft methodologies. Consequence of similarities in operating environment and aerodynamic surface configuration. Technology available - theory developed, validated by comparison with test data, incorporated into rotorcraft codes. High subsonic to transonic rotor speed, low to moderate Reynolds number. Structural and aerodynamic models for high aspect-ratio wings and propeller blades. Dynamic and aerodynamic interaction of wing/airframe and propellers. Large deflections, arbitrary planform. Steady state flight, maneuvers and response to turbulence. Linearized state space models. This technology has not been extensively applied to HALE configurations. Correlation with measured HALE performance and behavior required before can rely on tools.

Young, Larry↗

Low Reynolds Number Aerodynamic Characteristics of Several Airplane Configurations Designed to Fly in the Mars Atmosphere at Subsonic Speeds

A 1/4-scale wind tunnel model of an airplane configuration developed for short duration flight at subsonic speeds in the Martian atmosphere has been tested in the Langley Research Center Transonic Dynamics Tunnel. The tunnel was pumped down to extremely low pressures to represent Martian Mach/Reynolds number conditions. Aerodynamic data were obtained and upper and lower surface wind pressures were measured at one spanwise station on some configurations. Three unswept wings of the same planform but different airfoil sections were tested. Horizontal tail incidence was varied as was the deflection of plain and split trailing-edge flaps. One unswept wing configuration was tested with the lower part of the fuselage removed and the vertical/horizontal tail assembly inverted and mounted from beneath the fuselage. A sweptback wing was also tested. Tests were conducted at Mach numbers from 0.50 to 0.90. Wing chord Reynolds number was varied from 40,000 to 100,000 and angles of attack and sideslip were varied from -10deg to 20deg and -10deg to 10deg, respectively.

Re, Richard J.↗

Aerodynamic characteristics of wing-body configuration with two advanced general aviation airfoil sections and simple flap systems

Aerodynamic characteristics of a general aviation wing equipped with NACA 65 sub 2-415, NASA GA(W)-1, and NASA GA(PC)-1 airfoil sections were examined. The NASA GA(W)-1 wing was equipped with plain, split, and slotted partial- and full-span flaps and ailerons. The NASA GA(PC)-1 wing was equipped with plain, partial- and full-span flaps. Experimental chordwise static-pressure distribution and wake drag measurements were obtained for the NASA GA(PC)-1 wing at the 22.5-percent spanwise station. Comparisons were made between the three wing configurations to evaluate the wing performance, stall, and maximum lift capabilities. The results of this investigation indicated that the NASA GA(W)-1 wing had a higher maximum lift capability and almost equivalent drag values compared with both the NACA 65 sub 2-415 and NASA GA(PC)-1 wings. The NASA GA(W)-1 had a maximum lift coefficient of 1.32 with 0 deg flap deflection, and 1.78 with 41.6 deg deflection of the partial-span slotted flap. The effectiveness of the NASA GA(W)-1 plain and slotted ailerons with differential deflections were equivalent. The NASA GA(PC)-1 wing with full-span flaps deflected 0 deg for the design climb configuration showed improved lift and drag performance over the cruise flap setting of -10 deg.

Morgan, H. L., Jr.↗

Aerodynamic Performance and Acoustic Measurements of a High-Lift Propeller in an Isolated Configuration

A series of aerodynamic performance and acoustic measurements has been made on a high-lift propeller intended for utilization on a distributed electric propulsion (DEP) aircraft. Tests were performed in the NASA Langley Low Speed Aeroacoustic Wind Tunnel (LSAWT), which has recently undergone a capability enhancement for the testing of small propellers/rotors and small unmanned aircraft system (UAS) platforms. The objectives of this testing campaign are two-fold: first to demonstrate the facility capabilities for performing small propeller aeroacoustic testing, and second to compare experimental measurements with computational fluid dynamic (CFD) predictions and CFD-based acoustic predictions of the tested propeller configurations for tool development and validation purposes.

Zawodny, Nikolas S.↗

Space shuttle: Basic subsonic static aerodynamic characteristics for Grumman H-33 orbiter configuration (M equals 0.17)

Results of an experimental aerodynamic investigation of the H-33 space orbiter are presented. The investigation was undertaken to determine static aerodynamic characteristics of the orbiter at a Mach number of 0.17. These data were determined by employing a 1/25 scale model of the orbiter for pitch and yaw variations of -4 degrees to 24 degrees to 15 degrees, respectively. Investigations were conducted in the 7 - by - 10 foot wind tunnel.

Jung, W.↗

Static and dynamic aeroelastic characterization of an aerodynamically heated generic hypersonic aircraft configuration

This work-in-progress presentation describes an ongoing research activity at the NASA Langley Research Center to develop analytical methods for the prediction of aerothermoelastic stability of hypersonic aircraft including active control systems. The objectives of this research include application of aerothermal loads to the structural finite element model, determination of the thermal effects on flutter, and assessment of active controls technology applied to overcome any potential adverse aeroelastic stability or response problems due to aerodynamic heating- namely flutter suppression and ride quality improvement. For this study, a generic hypersonic aircraft configuration was selected which incorporates wing flaps, ailerons and all-moveable fins to be used for active control purposes. The active control systems would use onboard sensors in a feedback loop through the aircraft flight control computers to move the surfaces for improved structural dynamic response as the aircraft encounters atmospheric turbulence.

Heeg, Jennifer↗

Hypersonic aerodynamic characteristics of an all-body research aircraft configuration

An experimental investigation was conducted at Mach 6 to determine the hypersonic aerodynamic characteristics of an all-body, delta-planform, hypersonic research aircraft (HYFAC configuration). The aerodynamic characteristics were obtained at Reynolds numbers based on model length of 2.84 million and 10.5 million and over an angle-of-attack range from minus 4 deg to 20 deg. The experimental results show that the HYFAC configuration is longitudinally stable and can be trimmed over the range of test conditions. The configuration had a small degree of directional stability over the angle-of-attack range and positive effective dihedral at angles of attack greater than 2 deg. Addition of canards caused a decrease in longitudinal stability and an increase in directional stability. Oil-flow studies revealed extensive areas of separated and vortex flow on the fuselage lee surface. A limited comparison of wind-tunnel data with several hypersonic approximations indicated that, except for the directional stability, the tangent-cone method gave adequate agreement at control settings between 5 deg and minus 5 deg and positive lift coefficient. A limited comparison indicated that the HYFAC configuration had greater longitudinal stability than an elliptical-cross-section configuration, but a lower maximum lift-drag ratio.

Clark, L. E.↗

Aerodynamic features of designed strake-wing configurations

Sixteen analytically and empirically designed strakes have been aerodynamically tested on a common wing-body to determine the longitudinal characteristics of the configurations. These strakes were selected, in general, due to their superior performance in a water-tunnel test. There they exhibited a good correlation between the hypothesized high value of angle of attack for strake vortex breakdown and the high value of leading-edge suction at the strake tip. The lift and pitch data were reasonably well predicted by an extended suction analogy method, and the lift agreement improved with increasing strake area. The strake-vortex-breakdown angle and configuration maximum lift generally increase with increasing strake area and, to some extent, strake tip leading-edge suction value. The best strake configurations all developed about the same maximum area efficiency value despite their differences in size.

Lamar, J. E.↗

Unsteady transonic flow calculations for two-dimensional canard-wing configurations with aeroelastic applications

Unsteady transonic flow calculations for aerodynamically interfering airfoil configurations are performed as a first step toward solving the three dimensional canard wing interaction problem. These calculations are performed by extending the XTRAN2L two dimensional unsteady transonic small disturbance code to include an additional airfoil. Unsteady transonic forces due to plunge and pitch motions of a two dimensional canard and wing are presented. Results for a variety of canard wing separation distances reveal the effects of aerodynamic interference on unsteady transonic airloads. Aeroelastic analyses employing these unsteady airloads demonstrate the effects of aerodynamic interference on aeroelastic stability and flutter. For the configurations studied, increases in wing flutter speed result with the inclusion of the aerodynamically interfering canard.

Batina, J. T.↗

Unsteady transonic flow calculations for two-dimensional canard-wing configurations with aeroelastic applications

Unsteady transonic flow calculations for aerodynamically interfering airfoil configurations are performed as a first-step toward solving the three-dimensional canard-wing interaction problem. These calculations are performed by extending the XTRAN2L two-dimensional unsteady transonic small-disturbance code to include an additional airfoil. Unsteady transonic forces due to plunge and pitch motions of a two-dimensional canard and wing are presented. Results for a variety of canard-wing separation distances reveal the effects of aerodynamic interference on unsteady transonic airloads. Aeroelastic analyses employing these unsteady airloads demonstrate the effects of aerodynamic interference on aeroelastic stability and flutter. For the configurations studied, increases in wing flutter speed result with the inclusion of the aerodynamically interfering canard.

Batina, J. T.↗

An integrated analytical aeropropulsive/aeroelastic model for the dynamic analysis of hypersonic vehicles

The development of an approach to the determination of the dynamic characteristics of hypersonic vehicles which is intentionally generic and basic is given. The approach involves a 2D hypersonic aerodynamic analysis utilizing Newtonian theory, coupled with a 1D aero/thermoanalysis of the flow in a scramjet-type propulsion system. In addition, the airframe is considered to be elastic, and the structural dynamics are characterized in terms of a simple lumped-mass model of the invacuo vibration modes. The vibration modes are coupled to the rigid-body modes through the aero/propulsive forces acting on the structure. The control effectors considered on a generic study configuration include aerodynamic pitch-control surfaces, as well as engine fuel flow and diffuser area ratio. The study configuration is shown to be highly statically unstable in pitch, and to exhibit strong airframe/engine/elastic coupling in the aeroelastic and attitude dynamics, as well as the engine responses.

Chavez, Frank R.↗