Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Elastic constants in monocrystalline tungsten under quasi-hydrostatic pressures to 11.3 GPa

Compressional (P) and shear (S) wave velocities of tungsten single crystals along the [100] and [110] directions were measured using ultrasonic interferometry at room temperature up to 11.3 GPa. Least-squares fitting of $V$$^{[100]}_{P}$, $V$$^{[100]}_{S}$, $V$$^{[110]}_{P}$, and pressure to finite strain (FS) equations yields the elastic constants: C 11 = 523.5(5) GPa, C 12 = 205.1(32) GPa, and C 44 = 160.8(4) GPa, along with their respective pressure derivatives: $C$$^{′}_{11}$ = 6.20(2), $C$$^{′}_{12}$ = 3.35(1), and $C$$^{′}_{44}$ = 1.65(6). Using the Voigt–Reuss–Hill approximation, the elastic moduli were derived as K S0 = 311.2(22) GPa and G 0 = 160.2(7)GPa, along with their respective pressure derivatives: $K$$^{′}_{S0}$ = 4.30(4) and $G$$^{′}_{0}$ = 1.56(1). The Debye temperature of tungsten was determined to be 380.7(8) K, showing good agreement with previous calorimetric measurements. The elastic anisotropy increases slightly from 1.01(1) at ambient pressure to 1.03(1) at 11.3 GPa, suggesting that tungsten remains nearly isotropic under compression. Poisson's ratio slightly increased from 0.281(3) to 0.288(3) with pressure. Additionally, Pugh's ratio decreased from 0.512(4) to 0.494(4), while Pettifor's ratio increased from 0.148(10) to 0.175(10) as pressure reached 11.3 GPa. These results suggest that tungsten is weakly ductile compared to the critical thresholds for ductile behavior (i.e., Pugh's ratio <0.6 and Pettifor's ratio >0, indicating ductile behavior), but that its ductility increases marginally under pressure.

Wang, Ran [Stony Brook University, NY (United Stat↗

Nonlinear Dynamics and Phase Space Manipulations of High-Brightness Beams

The project consisted of two main tasks. Each task had several specific aims. The three main objectives of Task 1 were: 1. Investigation of the flat beam technique to produce high transverse emittance ratio longitudinally-compressed bunches, 2. Exploration of a new chicane-like transverse-to-longitudinal phase space exchanger for precise pulse shaping and emittance exchange, 3. Applications of flat-beam with shaped current profile(s) to dielectric wakefield acceleration in an asymmetric waveguide. The outcome of our research was to performed details simulations of flat-beam generation and compression. Some preliminary experiment on flat-beam generation and compression were conducted at the FAST-IOTA injector in parallel to commissioning activities. Likewise, the longitudinal phase-space transformation was not fully explored; we participated in experiments conducted at the Argonne Wakefield Accelerator and especially introduced a simple transverse-shaping technique.

43 PARTICLE ACCELERATORS↗

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

In this paper, cold extrusion was successfully used to fabricate the fine-grained pure Mg bar with average grain size of 2.5 μm. The microstructure, texture and mechanical properties were evaluated by electron backscattering diffraction and mechanical test. The results showed that the corresponding yield strengths for as-extruded fine-grained pure Mg were 130.8 MPa in tension and 125.6 MPa in compression, leading to a greatly improved yield asymmetry ratio. The improvement in tension–compression asymmetry is mainly due to grain refinement which favors the suppression of deformation twinning in compression and promotion of multi-deformation modes both in tension and compression at small strains.

36 MATERIALS SCIENCE↗

Simple and Inexpensive Method of Wood Pellets Macro-porosity Measurement

A novel simplified stereometric measurement method for determining the macro-porosity of wood pellets through geometrical approach was successfully developed and tested. The irregular ends of pellets of circular cross-section were sanded flat so that their geometry becomes cylinder and their volumes evaluated using mensuration formula. Such formed cylindrical pellets were loose or tap filled to selected volumes to evaluate the macro-porosity and the constant specific weight. The method was extended to evaluate actual wood pellets properties. Overall macro-porosity of actual wood pellets was determined as 41.0±2.5% and 35.5±2.7%, mean bulk density as and , and classified as “Class-3:Medium” and “Class-3&4:Medium to Low” for loose and tapped fills, respectively. Hausner ratio and Carr’s compressibility index classify wood pellets as “freely flowing.” The developed stereometric method can be used as a handy inexpensive laboratory procedure to estimate the macro-porosity of different types and makes of wood pellets and other similar packaged materials.

09 BIOMASS FUELS↗

A granular inorganic adsorbent highly selective to cesium - 15058

The metal ferrocyanide granular inorganic adsorbent based on phosphate geo-polymer for the removal of Cs in either batch or packed-bed operation has been developed in this study. The adsorbent was synthesized from the acid-base reaction between metal ferrocyanide and acidic phosphate at room temperature. In this work, the compressive strength of granular inorganic adsorbent was investigated under different liquid-to-solid, metal ferrocyanide-to-geo-polymer and MgO-to-KH{sub 2}PO{sub 4} ratios. The result showed that the compressive strength of the adsorbent increased with the increase of MgO-to-KH{sub 2}PO{sub 4} ratio. On the other hand, the increase of metal ferrocyanide-to-geo-polymer ratio or liquid-to-solid ratio lowered the compressive strength of the adsorbent. It was found that the optimization of liquid-to-solid, metal ferrocyanide-to-geo-polymer and MgO-to-KH{sub 2}PO{sub 4} ratios was important in improving both the compressive strength and the adsorption capacity of the adsorbent. In this study, the synthesized granular inorganic adsorbent has demonstrated a Cs removal efficiency of over 99% and an adsorption capacity of 1.1-1.3 meq/g in simulation wastewater containing 2000 ppm Cs under adsorbent dose of 0.0067 g/ml. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

First-principles equation of state and shock compression predictions of warm dense hydrocarbons

We use path integral Monte Carlo and density functional molecular dynamics to construct a coherent set of equations of state (EOS) for a series of hydrocarbon materials with various C:H ratios (2:1, 1:1, 2:3, 1:2, and 1:4) over the range of 0.07–22.4gcm –3 and 6.7 × 10 3 – 1.29 × 10 8 K. The shock Hugoniot curve derived for each material displays a single compression maximum corresponding to K-shell ionization. For C:H = 1:1, the compression maximum occurs at 4.7-fold of the initial density and we show radiation effects significantly increase the shock compression ratio above 2 Gbar, surpassing relativistic effects. The single-peaked structure of the Hugoniot curves contrasts with previous work on higher-Z plasmas, which exhibit a two-peak structure corresponding to both K- and L-shell ionization. Analysis of the electronic density of states reveals that the change in Hugoniot structure is due to merging of the L-shell eigenstates in carbon, while they remain distinct for higher-Z elements. Lastly, we show that the isobaric-isothermal linear mixing rule for carbon and hydrogen EOS is a reasonable approximation with errors better than 1% for stellar-core conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Further experiments and modeling for microscale compression molding of metals at elevated temperatures

Replication of metallic high-aspect-ratio microscale structures (HARMS) by compression molding has been demonstrated recently. Molding replication of metallic HARMS can potentially lead to low-cost fabrication of a wide variety of metal-based microdevices. Understanding the mechanics of metal micromolding is critical for assessing the capabilities and limitations of this replication technique. This paper presents results of instrumented micromolding of Al. Measured molding response was rationalized with companion high-temperature tensile testing of Al using a simple mechanics model of the micromolding process. The present results suggest that resisting pressure on the mold insert during micromolding is governed primarily by the yield stress of the molded metal at the molding temperature and a frictional traction on the sides of the insert. Furthermore, the influence of strain rate is also considered.

36 MATERIALS SCIENCE↗

Temperature-dependent mechanical property testing of nitrate thermal storage salts.

Three salt compositions for potential use in trough-based solar collectors were tested to determine their mechanical properties as a function of temperature. The mechanical properties determined were unconfined compressive strength, Young's modulus, Poisson's ratio, and indirect tensile strength. Seventeen uniaxial compression and indirect tension tests were completed. It was found that as test temperature increases, unconfined compressive strength and Young's modulus decreased for all salt types. Empirical relationships were developed quantifying the aforementioned behaviors. Poisson's ratio tends to increase with increasing temperature except for one salt type where there is no obvious trend. The variability in measured indirect tensile strength is large, but not atypical for this index test. The average tensile strength for all salt types tested is substantially higher than the upper range of tensile strengths for naturally occurring rock salts. Interest in raising the operating temperature of concentrating solar technologies and the incorporation of thermal storage has motivated studies on the implementation of molten salt as the system working fluid. Recently, salt has been considered for use in trough-based solar collectors and has been shown to offer a reduction in levelized cost of energy as well as increasing availability (Kearney et al., 2003). Concerns regarding the use of molten salt are often related to issues with salt solidification and recovery from freeze events. Differences among salts used for convective heat transfer and storage are typically designated by a comparison of thermal properties. However, the potential for a freeze event necessitates an understanding of salt mechanical properties in order to characterize and mitigate possible detrimental effects. This includes stress imparted by the expanding salt. Samples of solar salt, HITEC salt (Coastal Chemical Co.), and a low melting point quaternary salt were cast for characterization tests to determine unconfined compressive strength, indirect tensile strength, coefficient of thermal expansion (CTE), Young's modulus, and Poisson's ratio. Experiments were conducted at multiple temperatures below the melting point to determine temperature dependence.

14 SOLAR ENERGY↗

Multi-stage heat release of multi-component fuels: Insights and implications for advanced engine operation

Multi-stage heat release (MSHR) is a unique phenomenon typically seen in lean/diluted and low- to intermediate-temperature combustion. Despite its relevance to advanced engine operation, the MSHR of multi-component fuels has barely been quantified. This study aims to characterize the MSHR of multi-component fuels in a rapid compression machine (RCM) at conditions representative of advanced combustion engines. New experimental data are first reported in the RCM at an equivalence ratio of 0.4, pressure of 60 bar and temperatures from 702 to 795 K for a research grade, multi-component gasoline surrogate, termed PACE-20. Here, experiments confirm the existence of MSHR for PACE-20 at all temperatures, and reveal the strong inhibiting effect of temperature on MSHR, where increasing temperature inhibits MSHR by suppressing first stage heat release and promoting second and third stage heat release. A detailed chemical kinetic model is also adopted to model the experiments, with good agreement observed. The response of MSHR characteristics to changes in different engine operating parameters (i.e., temperature, pressure, equivalence ratio and CO 2 dilution level) and fuel compositions (i.e., mole fraction of n-pentane, n-heptane, isooctane, cyclopentane, 1-hexene, ethanol and aromatics in PACE-20) is further evaluated via statistical analysis coupling quasi-random sampling, extensive computer experiments and high-dimensional model representation. The change in MSHR is characterized through 8 quantities of interest (QOIs), i.e., duration and extent of each heat release stage, and their standard deviations. The analysis highlights the dependence of the QOIs on the individual parameters as well as their interplays, with temperature exhibiting the strongest impact among all parameters. Furthermore, it is demonstrated that if MSHR is to be facilitated and combustion phasing is to be extended to enable engine operation at higher compression ratios, it is recommended to operate the engine at low intake temperatures, boosted intake pressures and high CO 2 dilutions (i.e., high EGR levels) with gasoline fuels containing more n-pentane and less aromatics.

42 ENGINEERING↗

Pressure dependence of Poisson’s ratio of glassy Baltic amber studied by Brillouin scattering spectroscopy

Amber is a typical natural glass with very long aging time. Elastic properties of amber at high pressures have been studied using Brillouin scattering and a diamond anvil cell. Both longitudinal and transverse acoustic modes have been observed up to 12 GPa. The pressure dependences of longitudinal, shear, Young’s, and bulk moduli, compressibility, and Poisson’s ratio were determined. The longitudinal, shear, Young’s, bulk moduli show the remarkable increase, and compressibility shows a marked decrease with increasing pressure. However, it is found that the pressure dependence of Poisson’s ratio is very small. The mechanism of this small pressure dependence was discussed. Finally, the Cauchy type relation between longitudinal and shear moduli was examined. Its coefficients show the deviation from the Cauchy relation owing to the coexistence of different intermolecular interactions in amber.

07 ISOTOPE AND RADIATION SOURCES↗

Temperature dependent mechanical property testing of nitrate thermal storage salts.

Three salt compositions for potential use in trough-based solar collectors were tested to determine their mechanical properties as a function of temperature. The mechanical properties determined were unconfined compressive strength, Young's modulus, Poisson's ratio, and indirect tensile strength. Seventeen uniaxial compression and indirect tension tests were completed. It was found that as test temperature increases, unconfined compressive strength and Young's modulus decreased for all salt types. Empirical relationships were developed quantifying the aforementioned behaviors. Poisson's ratio tends to increase with increasing temperature except for one salt type where there is no obvious trend. The variability in measured indirect tensile strength is large, but not atypical for this index test. The average tensile strength for all salt types tested is substantially higher than the upper range of tensile strengths for naturally occurring rock salts.

14 SOLAR ENERGY↗

Anisotropies of the Magnetic Field Fluctuations at Kinetic Scales in the Solar Wind: Cluster Observations

We present the first statistical study of the anisotropy of the magnetic field turbulence in the solar wind between 1 and 200 Hz, i.e., from proton to sub-electron scales. We consider 93 ten-minute intervals of the Cluster/STAFF measurements. We find that the fluctuations δB{sub ⊥}{sup 2} are not gyrotropic at a given frequency f, a property already observed at larger scales (∥/⊥ means parallel/perpendicular to the average magnetic B{sub 0}). This non-gyrotropy gives indications of the angular distribution of the wave vectors k: at f< 10 Hz, we find that k{sub ⊥}≫k{sub ∥}, mainly in the fast wind; at f > 10 Hz, fluctuations with a non-negligible k {sub ∥} are also present. We then consider the anisotropy ratio δB{sub ∥}{sup 2}/δB{sub ⊥}{sup 2}, which is a measure of the magnetic compressibility of the fluctuations. This ratio, always smaller than 1, increases with f. It reaches a value showing that the fluctuations are more or less isotropic at electron scales, for f⩾50 Hz. From 1 to 15–20 Hz, there is a strong correlation between the observed compressibility and the one expected for the kinetic Alfvén waves (KAWs), which only depends on the total plasma β. For f>15--20 Hz, the observed compressibility is larger than expected for KAWs, and it is stronger in the slow wind: this could be an indication of the presence of a slow-ion acoustic mode of fluctuations, which is more compressive and is favored by the larger values of the electron to proton temperature ratio generally observed in the slow wind.

79 ASTRONOMY AND ASTROPHYSICS↗

Compressive Deformation Behavior of Open-Cell Cu-Zn-Al Alloy Foam Made Through P/M Route Using Mechanically Alloyed Powder

Cu-Zn-Al foams of varying porosity fractions using mechanical alloyed powder have been made through powder metallurgy route. Here, NH{sub 4} (HCO{sub 3}) was used as a space holder. Mechanically alloyed Cu-Zn-Al is made using a planetary ball mill taking the ratio of Cu/Zn/Al = 70:25:5 (by weight ratio). The ball/powder ratios were varied in the four ranges 10:1, 15:1, 20:1, and 25:1. Green compacts of milled powder and space holder samples were sintered at three stages at three different temperatures 350, 550, and 850 °C for 1 h at each stage. The crystalline size and particle size as a function of ball/powder ratios were examined. The compressive deformation responses of foams are varied with relative density and the ball/powder ratio. The plateau stress and energy absorption of these foams increase with an increase in relative density but decreases with increase in ball/powder ratio, even though crystalline size decreases. This has further been explained on the basis of particle morphology as a function of ball/powder ratio.

36 MATERIALS SCIENCE↗

High-Temperature Interactions Between Vanadium-Titanium Magnetite Carbon Composite Hot Briquettes and Pellets Under Simulated Blast Furnace Conditions

The high-temperature interactions between vanadium-titanium magnetite carbon composite hot briquettes (VTM-CCBs) and pellets were systematically investigated under simulated blast furnace conditions with respect to the reduction behavior, softening–melting–dripping characteristics, gas permeability, and Ti(C, N) precipitation mechanisms. The results showed that VTM-CCB charging can promote the reduction of the pellet in the packed bed and decrease the compressive strength of the pellet after reduction. The compressive strength of the VTM-CCB after reduction decreased with increasing temperature when the FC/O ratio (the ratio of the fixed carbon mol(C) in coal to the reducible oxygen mol(O) in iron oxides) was higher than 1.0. With an FC/O ratio lower than 1.0, the compressive strength of the VTM-CCB initially decreased and then increased. The FC/O ratio has a significant influence on the softening–melting interaction mechanism between the VTM-CCB and the pellet. With an FC/O ratio of 0.8, the bonding layer at the interface between the pellet and the VTM-CCB (consisting of molten fayalitic slag) can promote the softening process, thereby decreasing the softening start and end temperatures. By increasing the FC/O ratio to 1.4, a dense metallic iron shell with relatively high strength formed at the interface and restricted the collapse of the packed bed, thereby increasing the softening start and end temperatures and ensuring the transport of the reduction gas through the packed bed. The melting point of the primary slag phase increased with increasing FC/O ratio due to a decrease in the FeO content, which resulted in an increase in the melting start temperature from 1273 °C to 1294 °C (1546 K to 1567 K). The gas permeability in the cohesive zone increased with an increasing FC/O ratio of the VTM-CCB due to a combination of the skeletal role performed by the residual VTM-CCB and the decrease in the liquid slag proportion. In addition, as the FC/O ratio increased to 1.4, unconsumed carbon promoted the precipitation of Ti(C, N) at the slag–carbon and slag–metal interfaces, which resulted in a substantial increase in the dripping temperature and deterioration of the dripping behavior of the packed bed. Therefore, to suppress the precipitation of Ti(C, N) and improve the dripping behavior of the packed bed, the FC/O ratio of the charged VTM-CCB should be controlled within an appropriate range.

36 MATERIALS SCIENCE↗

Influence of CaO/FeO ratio on the formation mechanism and properties of alkali-activated Fe-rich slags

Highlights: • Effect of the CaO/FeO molar ratio in alkali-activated Fe-rich slags is unraveled. • Low CaO/FeO molar ratios enhance the early kinetics and compressive strength. • Reaction extent and strength further increase with higher CaO/FeO ratio after 7 days. • Fe{sup 2+}-trioctahedral layers of the binder are hydroxylated and in a silicate phase. • The final strength is determined by the influence of Ca on the reaction products. In the search for CO{sub 2} mitigating cement technologies, alkali-activated Fe-rich slags present a possible alternative. The influence of the chemical composition of the synthetic Fe-silicate slag on the reaction mechanisms is assessed by varying the CaO/FeO molar ratio. The alkali-activated Fe-rich slags consist of trioctahedral layers that are shown to be hydroxylated and in contact with silicates, in a similar way to phyllosilicate minerals. The formation of this phyllosilicate-like structure is hindered during the first days for samples with high CaO/FeO ratios, because of the partial incorporation of Ca in the trioctahedral layers. At later ages, the samples with higher CaO/FeO ratios gain in reaction extent, to exceed the reaction extent of low CaO/FeO ratios at 28 days and beyond. The increase in compressive strength is even more pronounced than the effect on the reaction extent, which underlines the importance of Ca on the inherent strength of the binding phases.

36 MATERIALS SCIENCE↗

An experimental study of the autoignition characteristics of conventional jet fuel/oxidizer mixtures: Jet-A and JP-8

Ignition delay times of Jet-A/oxidizer and JP-8/oxidizer mixtures are measured using a heated rapid compression machine at compressed charge pressures corresponding to 7, 15, and 30 bar, compressed temperatures ranging from 650 to 1100 K, and equivalence ratios varying from 0.42 to 2.26. When using air as the oxidant, two oxidizer-to-fuel mass ratios of 13 and 19 are investigated. To achieve higher compressed temperatures for fuel lean mixtures (equivalence ratio of {proportional_to}0.42), argon dilution is also used and the corresponding oxidizer-to-fuel mass ratio is 84.9. For the conditions studied, experimental results show two-stage ignition characteristics for both Jet-A and JP-8. Variations of both the first-stage and overall ignition delays with compressed temperature, compressed pressure, and equivalence ratio are reported and correlated. It is noted that the negative temperature coefficient phenomenon becomes more prominent at relatively lower pressures. Furthermore, the first-stage-ignition delay is found to be less sensitive to changes in equivalence ratio and primarily dependent on temperature. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Hydration studies of calcium sulfoaluminate cements blended with fly ash

The main objective of this work is to study the hydration and properties of calcium sulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied parameters were: i) FA content, 0, 15 and 30 wt.%; and ii) water addition, water-to-CSA mass ratio (w/CSA = 0.50 and 0.65), and water-to-binder mass ratio (w/b = 0.50). Finally, compressive strengths after 6 months of 0 and 15 wt.% FA [w/CSA = 0.50] mortars were similar: 73 ± 2 and 72 ± 3 MPa, respectively. This is justified by the filler effect of the FA as no strong evidences of reactivity of FA with CSA were observed. These results support the partial substitution of CSA cements with FA with the economic and environmental benefits.

36 MATERIALS SCIENCE↗

Poisson's Ratio of a Hyperelastic Foam Under Quasi-static and Dynamic Loading

Poisson's ratio is a material constant representing compressibility of material volume. However, when soft, hyperelastic materials such as silicone foam are subjected to large deformation into densification, the Poisson's ratio may rather significantly change, which warrants careful consideration in modeling and simulation of impact/shock mitigation scenarios where foams are used as isolators. The evolution of Poisson's ratio of silicone foam materials has not yet been characterized, particularly under dynamic loading. In this study, radial and axial measurements of specimen strain are conducted simultaneously during quasi-static and dynamic compression tests to determine the Poisson's ratio of silicone foam. The Poisson's ratio of silicone foam exhibited a transition from compressible to nearly incompressible at a threshold strain that coincided with the onset of densification in the material. Poisson's ratio as a function of engineering strain was different at quasi-static and dynamic rates. Here, the Poisson's ratio behavior is presented and can be used to improve constitutive modeling of silicone foams subjected to a broad range of mechanical loading.

36 MATERIALS SCIENCE↗