Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONTINUOUS WAVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Capture Cavities for the CW Polarized Positron Source Ce+BAF

The initial design of the capture cavities for the continuous wave (CW) polarized positron beams at Jefferson Lab (Ce+BAF) is presented. A chain of standing wave multi-cell copper cavities inside a solenoid tunnel are selected to bunch/capture positrons. The cavity design strategy is presented to accommodate constrains from the large phase distribution of the incident beams, RF power, radiation and RF heating, beam loading, etc. to improve the capture efficiency. A matrix of design parameters' range are given for future system optimization when the capture cavities are considered together with other sub-systems and beam dynamics. The contents will also be useful for other CW cavity design for beams with large phase space distribution.

Wang, Shaoheng↗

RF and Mechanical Design of a 915 MHz SRF Cavity for Conduction-Cooled Cryomodules

Conduction-cooled SRF niobium cavities are being developed for use in compact, continuous-wave electron linear accelerators for a variety of industrial applications. A 915 MHz two-cell cavity has been designed to achieve an energy gain of 3.5 MeV. The design of the cell shape aims at minimizing the peak surface magnetic field. Field flatness is achieved by adjusting the length of the outer end half-cells. The higher-order mode analysis shows that absorbers are not required for a moderate beam current of 5 mA. One of the beam tubes has two side-ports for insertion of coaxial fundamental power couplers. The mechanical design and analysis were done to maintain a stress near or less than 15.5 MPa for all anticipated loading conditions. This is half the measured yield strength and is to provide relief from creep when cavity is evacuated and stored with outside atmospheric pressure.

Ciovati, Gianluigi↗

Physics Design of Proton/Ion SRF Accelerators

Superconducting Radio Frequency (SRF) technology has become foundation of the modern high energy particle accelerators. The technology enables a higher accelerating field with minimal power dissipation and a stronger compact magnetic field. These advancements have broadened the operational horizon of the particle accelerators making a higher duty factor and Continuous Wave (CW) beam operations both feasible and economically viable. The intensity frontier research founded on generation of intense beam of exotic particles including but not limited to neutrinos, muons, kaons and neutrons as well as practical applications involving transmutation of nuclear reactor waste, rare isotopes generation, sub-critical nuclear power generation etc. could be accomplished efficiently only by using superconducting proton/ions particle accelerators. As a result, many newly constructed or under construction high energy accelerator facilities around the world such as Proton Improvement Plan-II (PIP-II) at Fermilab, FRIB at MSU, ESS at Sweden are utilizing SRF accelerators. This talk presents the design philosophy of SRF proton/ion particle accelerator, with a focus on optimizing its performance while addressing physics and operational challenges including the fault scenarios, machine availability and preservation of crucial beam parameters.

Saini, Arun↗

The Fermilab Facility for Dark Matter Discovery (F2D2): A Conceptual PIP-II Beam Stop Facility for Dark Sector Physics

What do the accelerator target stations of the next decade look like? The NuMI beamline, fed by Fermilab s Main Injector, recently exceeded 1 MW beam power. Future experiments fed by the PIP-II superconducting linear accelerator might demand upwards of 2 MW in continuous-wave mode, compared to the pulsed beams typical of neutrino experiments. Looking further into the future, the Muon Collider front end includes a target station with even higher power 5 MW or beyond. How do we build a 2+ MW target facility? How does a high-power, low-energy, CW beam affect target design compared to conventional high-energy neutrino targets? How do we manage radiation and heat? How is the facility serviced? What is the current state of capability, and what technologies do we need to develop? These questions are answered in the context of F2D2, a conceptual target station design for dark sector physics experiments using beam from PIP-II.

Williams, Jonathan K.↗

ODU Optimization of Nb3Sn supttering on SRF structures

High efficiency Superconducting radio-frequency (SRF) cavities are the key technology to cost-effective Continuous Wave (CW) SRF accelerators. Recent advances in Nb3Sn coatings on the inner surface of SRF cavities showed the potential for this material to significantly cut the capital and operating cost of SRF accelerators. The best results are presently achieved with Nb3Sn films coated by using the so-called vapor diffusion technique. Several alternative approaches have been and are being investigated such as electrochemical deposition, bronze routes, and sputtering. Among these techniques, magnetron sputtering is a versatile technique, which has been demonstrated to deposit Nb3Sn films on SRF cavities. The technique requires further development to compete with the results demonstrated on the cavities coated with the vapor diffusion techniques. The team to develop the novel technique includes a graduate student from Old Dominion University (ODU) and other experts. ODU Prof. Elsayed-Ali directs the graduate student to coat samples and cavities in the new coating system and analyze samples with different surface science techniques. Dr. Grigory Eremeev from Fermilab assists with 2.6 GHz cavities for coating, cavity characterization at cryogenic temperature, and result analysis. The research is funded by the Office of High Energy Physics at the US Department of Energy at both Fermilab and ODU

43 PARTICLE ACCELERATORS↗

DOE SCGSR Final Report - Project Accomplishments and Additional Materials

The major accomplishments of my project were successfully developing and testing the laser interferometry diagnostic on the Plasma Liner Experiment (PLX) at Los Alamos National Laboratory (LANL). This diagnostic helped advance my research by providing a simpler way to obtain electron density measurements of magnetized plasmas compared to other electron density diagnostics such as triple Langmuir probes. The laser used was a 561 nm continuous wave (CW) diode-pumped solid state (DPSS) laser. The PLX laser interferometry diagnostic consists of two parts. These include the launching and receiving sides of the laser diagnostic. The launching side consists of the main laser beam from the DPSS laser being split into five chords(probe beams) and a reference beam which are then directed with fiber optic couplers into fiber optic cables which transmit the probe beamsto the PLX vacuum chamber. The probe beams then pass through the plasma in the chamber and into the receiving side optics where they are again directed through fiber optic cables to be combined with the reference beam. The combined beams are transmitted via multi-mode fiber optic cables to photodiodes to convert the light signals into electrical signals. Before the electrical signals get digitized, they pass through bandpass and low pass filters to eliminate electromagnetic noise and unwanted frequencies. The electrical signals are then processed by IQ demodulators to determine phase angle difference between the probe and reference beams for each chord in order to calculate line-integrated electron density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First Results from A $Nb_3Sn$-Coated 1.5-Cell 650MHZ SRF Cavity for Cryogen-Free Industrial Accelerators

Fermilab is advancing the development of a compact, high-power electron beam accelerator using superconducting radio frequency (SRF) technology as a non-radioactive alternative to traditional radiological sources. The current design targets continuous-wave (CW) operation at \SI{1.6}{MeV} and \SI{20}{kW}. To ensure suitability for industrial environments, the system is being designed for cryogen-free operation, driving the adoption of a novel Nb$_3$Sn-coated 1.5-cell SRF cavity operating at \SI{650}{MHz}. This contribution reports on the fabrication, surface preparation, and Nb$_3$Sn coating process of the cavity, as well as first results from vertical test stand (VTS) measurements performed in a liquid helium bath. These initial tests mark a key milestone toward demonstrating the viability of conduction-cooled Nb$_3$Sn SRF cavities for industrial-scale deployment.

Tagdulang, Nikki Diala [Fermilab]↗

Transmission Line Based Sensor Design for FMCW Radar Processing of Collision Damage

This report presents a framework for transmission line ( T-L ) sensor design in Frequency Modulated Continuous Wave (FMCW) radar applications, with particular emphasis on modeling collision damage effects. Classical electromagnetic (EM) propagation theory is combined with impact mechanics to develop a model for analyzing transmission line behavior as a sensor under high-velocity impact conditions. The framework includes detailed mathematical derivations, spatial and temporal damage evolution models, and practical implementation considerations.

42 ENGINEERING↗

Positron Injector for Ce+BAF

A baseline concept for a continuous wave (CW) polarized positron injector was developed for the CEBAF at Jefferson Lab. This concept is based on the generation of CW longitudinally polarized positrons by a high-current, polarized electron beam 1 mA, 130-370 MeV, and 90% longitudinal polarization that passes through a rotating, water-cooled, tungsten target. The simulations for the Ce+BAF injector at the Low Energy Recirculator Facility (LERF) are performed, including positron beam generation, capture, energy selection, and acceleration to 123 MeV. The positron yield (or positron current) and longitudinal polarization are calculated considering the longitudinal and transverse CEBAF acceptances (<1% energy spread, 1.2 mm bunch length and normalized emittance of 100 mm·mrad). The impact of target thickness, electron beam energy, and transverse size on positron yield within the required emittance limit is evaluated. Target thermal and structural FEM analyses (ANSYS Fluent) are performed to determine the maximum electron beam current and minimum transverse beam size on the target.

Benesch, Jay [Thomas Jefferson National Accelerato↗

Lidar - HilFlowS - LLNL ZephIR300 - MOP - Processed Data

The ZephIR300 is a continuous wave LIDAR with a range of 10 m to 300 m. During HilFlowS the ZephIR300 was programmed to measure from 10 m to 150 m. In addition, the ZephIR300 provided a measurement at 1 m height using an onboard meteorological sensor. The ZephIR300 has a 30° scanning cone angle, data sampling rate of approximately 15 s, wind speed accuracy of 0.5 percent, and direction accuracy of 0.5°.

17 WIND ENERGY↗

Lidar - HilFlowS - LLNL ZephIR300 - WOP - Processed Data

The ZephIR300 is a continuous wave LIDAR with a range of 10 m to 300 m. During HilFlowS the ZephIR300 was programmed to measure from 10 m to 150 m. In addition, the ZephIR300 provided a measurement at 1 m height using an onboard meteorological sensor. The ZephIR300 has a 30° scanning cone angle, data sampling rate of approximately 15 s, wind speed accuracy of 0.5 percent, and direction accuracy of 0.5°.

17 WIND ENERGY↗

WINDPROF: Merged Best-Estimate Wind Profile Data – Rhode Island (WFIP3 Campaign)

WINDPROF provides 10-minute wind and turbulence profiles that integrate a scanning Doppler lidar, a continuous-wave profiling lidar, and a sonic anemometer across Northeast U.S. coastal and offshore sites during the WFIP3 campaign. Variables include wind speed, wind direction, vertical velocity, turbulence intensity, and turbulent kinetic energy, each with per-instrument quality control and inter-instrument agreement validation. Profiles are mapped to a standardized height grid – a dedicated near-surface level at the sonic measurement height (4 m AGL), 20 m spacing to 100 m, and 30 m spacing above – and carry component and derived uncertainty estimates. Heights are reported above ground level; the site's ground elevation is stored separately. The Rhode Island dataset covers 7 February 2024 – 4 September 2025.

17 WIND ENERGY↗

Developing New Q-meters for NMR Measurements of Polarized Solids

Enhanced polarization of target nuclei can be measured via the complex impedance of a resonant circuit coupled to the target while sweeping the circuit through the nuclear Larmor frequency, observing the absorption or emission of energy by the spins in the material. For decades, solid polarized targets at Jefferson Lab have relied upon continuous-wave Nuclear Magnetic Resonance polarization measurements using Liverpool Q-meter systems. These Liverpool Q-meters are no longer produced, and replacing the aging components is becoming increasingly difficult. The polarized target group at Bochum has produced replacement Q-meters in the Liverpool style using modern components, and we are following their example while researching improvemnts to the technique. We discuss our efforts to produce improved Q-meters for upcoming experiments utilizing solid polarized targets in Jefferson Lab's Hall B.

Maxwell, James↗

Liquid metal-based polarized positron generation benchmark using the GEANT4 toolkit

In this work, we report simulation results for the positron yield and polarization of polarized electron beams incident on GaInSn and PbBi liquid metal targets. One of the proposed upgrades to 12 GeV CEBAF is the use of a continuous wave polarized positron beam for physics experiments. High-Z liquid metal jets are excellent candidates for positron production targets because they can withstand high power beams. Polarized positron beams can be generated from a primary electron beam incident to thick high-Z targets through circular polarized bremsstrahlung conversion to linearly polarized pair production. This polarization transfer from the primary electron beam has been previously demonstrated at Jefferson Lab in the PEPPo experiment with a tungsten target at relatively low energies. Here we report Geant4 simulations for 10 and 120 MeV electron beams incident on GaInSn and PbBi liquid metal targets. These simulations are compared to simulations with a solid tungsten target, as well as with unpolarized simulations using MCNP6.

Lizarraga-Rubio, Victor Manuel↗

Overview of CW electron guns and LCLS-II RF gun performance

Various continuous-wave (CW) electron gun technologies are reviewed, including DC, superconducting radio frequency RF (SRF), hybrid DC-SRF and normal-conducting RF. Also, the SLAC Linac Coherent Light Source II (LCLS-II) normal-conducting RF gun and injector are described, and the performance to date, including the bunch emittance achieved and the dark current observed, is presented.

43 PARTICLE ACCELERATORS↗

High-brightness electron injectors for high-duty cycle X-ray free electron lasers

The successful development in the last two decades of X-ray free electron lasers (FELs) with their revolutionary brightness performance has been tightly dependent on the parallel development of electron guns and injectors capable of providing the high-brightness electron beams required by FELs lasing at these short wavelengths. The ultimate brightness delivered by a linear accelerator (linac) is already set at its injector and the remaining part of the accelerator can be only designed to preserve the injector performance. The technology to be used for the accelerator part of an X-Ray FEL strongly depends on the duty-cycle at which the FEL operates. Normal-conducting, room-temperature, copper-based radio frequency (RF) technology is typically used for low duty-cycles of up to approximately 10 −3 . For higher duty-cycles and up to continuous wave (CW) operation, the linac must rely on superconductive RF technology because, with the higher duty-cycle, the increasingly higher power dissipated in normal conducting RF structures becomes excessive for the warm technology. The situation changes in the lower energy part of the accelerator, where injector schemes, based on direct current, normal-conducting, and superconducting RF electron guns, are demonstrating the beam quality performance required by high-duty-cycle X-ray FELs. In this paper we start with a description of the requirements for such injectors, followed by an overview of the pursued technologies and schemes, and by a discussion on the main differences in terms of beam dynamics between low and high duty-cycle injectors.

Sannibale, Fernando↗

Deep Learning Based Superconducting Radio-Frequency Cavity Fault Classification at Jefferson Laboratory

This work investigates the efficacy of deep learning (DL) for classifying C100 superconducting radio-frequency (SRF) cavity faults in the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Lab. CEBAF is a large, high-power continuous wave recirculating linac that utilizes 418 SRF cavities to accelerate electrons up to 12 GeV. Recent upgrades to CEBAF include installation of 11 new cryomodules (88 cavities) equipped with a low-level RF system that records RF time-series data from each cavity at the onset of an RF failure. Typically, subject matter experts (SME) analyze this data to determine the fault type and identify the cavity of origin. This information is subsequently utilized to identify failure trends and to implement corrective measures on the offending cavity. Manual inspection of large-scale, time-series data, generated by frequent system failures is tedious and time consuming, and thereby motivates the use of machine learning (ML) to automate the task. This study extends work on a previously developed system based on traditional ML methods (Tennant and Carpenter and Powers and Shabalina Solopova and Vidyaratne and Iftekharuddin, Phys. Rev. Accel. Beams, 2020, 23, 114601), and investigates the effectiveness of deep learning approaches. The transition to a DL model is driven by the goal of developing a system with sufficiently fast inference that it could be used to predict a fault event and take actionable information before the onset (on the order of a few hundred milliseconds). Because features are learned, rather than explicitly computed, DL offers a potential advantage over traditional ML. Specifically, two seminal DL architecture types are explored: deep recurrent neural networks (RNN) and deep convolutional neural networks (CNN). We provide a detailed analysis on the performance of individual models using an RF waveform dataset built from past operational runs of CEBAF. In particular, the performance of RNN models incorporating long short-term memory (LSTM) are analyzed along with the CNN performance. Furthermore, comparing these DL models with a state-of-the-art fault ML model shows that DL architectures obtain similar performance for cavity identification, do not perform quite as well for fault classification, but provide an advantage in inference speed.

97 MATHEMATICS AND COMPUTING↗

Effect of Laser Beam Profile on Rotating Lattice Single Crystal Growth in Sb2S3 Model Glass

Laser heating of chalcogenide glasses has successfully produced rotating lattice single crystals through a solid-solid transformation. To better understand the nature of complex, orientation-dependent lattice rotation, we designed heat profiles of the continuous wave laser by beam shaping, fabricated larger Sb2S3 crystal dots in Sb2S3 glass, and investigated the lattice rotation where the crystal could grow in all radial directions under a circular thermal gradient. The results show that the rate of lattice rotation is highly anisotropic and depends on crystallographic direction. The nature of this rotation is the same in crystals of different orientation relative to the surface. The growth directions that align with the slip planes show the highest rate of rotation and the rotation rate gradually decreases away from this direction. Additionally, the presence of multiple growth directions results in a complicated rotation system. We suggest that the growth front influences the density of dislocations introduced during growth under confinement and thus affects the lattice rotation rate in these crystals.

36 MATERIALS SCIENCE↗