Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Evaluation of circumferential airflow uniformity entering combustors from compressors. Volume 2: Data supplement

A study of the airflow uniformity leaving compressors and entering combustors was made using compressors from two advanced engines, the J58 and F100/F401. The data used in the analysis of each case is presented in tabular form and computer-generated profile plots. A plot of the square root of the dynamic pressure ratio, which is similar to airflow deviation, is also presented.

Shadowen, J. H.↗
NASA NTRS1973

Performance of a low-pressure-ratio centrifugal compressor with four diffuser designs

A low-pressure-ratio centrifugal compressor was tested with four different diffuser configurations. One diffuser had airfoil vanes. Two were pipe diffusers. One pipe diffuser had 7.5 deg cone diffusing passages. The other had trumpet-shaped passages designed for linear static-pressure rise from throat to exit. The fourth configuration had flat vanes with elliptical leading edges similar to those of pipe diffusers. The side walls were contoured to produce a linear pressure rise. Peak compressor efficiencies were 0.82 with the airfoil vane and conical pipe diffusers, 0.80 with the trumpet, and 0.74 with the flat-vane design. Surge margin and useful range were greater for the airfoil-vane diffuser than for the other three.

Klassen, H. A.↗
NASA NTRS1972

Single stage evaluation of highly loaded high Mach number compressor stages. 6: Data and performance of cantilevered stator

A compressor stage with a rotor tip speed of 1600 ft/sec was tested to evaluate its performance with a cantilevered stator and a rotating inner shroud beneath the stator. Both the rotor blades and the stator vanes were composed of multiple circular arc airfoil sections. Comparison of data taken during this test of the cantilevered stator and previous tests with the same compressor and airfoil geometry in a shroud stator configuration showed only slight differences in stage performance with no significant effect on overall efficiency. However, the severity of the stator wake near the rotating hub was decreased at all flows including the near surge condition. Stall and wise open discharge corrected weight flows were the same as for the shrouded stator configuration.

Merrow, A. S.↗
NASA NTRS1973

Small, high pressure ratio compressor: Aerodynamic and mechanical design

The Small, High-Pressure-Ratio Compressor Program was directed toward the analysis, design, and fabrication of a centrifugal compressor providing a 6:1 pressure ratio and an airflow rate of 2.0 pounds per second. The program consists of preliminary design, detailed areodynamic design, mechanical design, and mechanical acceptance tests. The preliminary design evaluate radial- and backward-curved blades, tandem bladed impellers, impeller-and diffuser-passage boundary-layer control, and vane, pipe, and multiple-stage diffusers. Based on this evaluation, a configuration was selected for detailed aerodynamic and mechanical design. Mechanical acceptance test was performed to demonstrate that mechanical design objectives of the research package were met.

Bryce, C. A.↗
NASA NTRS1973

Small, high-pressure ratio compressor mechanical acceptance test, volume 2

The fabrication and mechanical testing of the high-pressure-ratio compressor are reported. Mechanical testing was performed to demonstrate overspeed capability, adequate rotor dynamics, electrical isolation of the gas bearing trunnion mounted diffuser and shroud and the effect of operating parameters (speed and pressure ratio) on clearance of the compressor test rig. The speed range covered was 20 to 120 percent of rated speed (80,000 rpm). Following these tests an acceptance test which consisted of a 5 hour run at 80,000 rpm was made with approximately design impeller to shroud clearances. For Vol. 1, see N73-26483.

Metty, G. R.↗
NASA NTRS1974

Computer program for predicting off-design performance of centrifugal compressors

Complete knowledge of compressor overall geometry and working fluid total inlet conditions is required for program's use. On given speed line, compressor performance is calculated for range of inlet velocity levels. Working fluid state conditions and flow properties are calculated using mean stream line one-dimensional analysis.

Galvas, M. R.↗
NASA NTRS1974

Test techniques for obtaining off-nominal compressor data during engine tests

Several unique techniques and related devices are described which are in use at the Lewis Research Center for off-design testing of fan and compressor sections in full-scale jet engines. The devices presented permit a wide range of experimental conditions and minimize downtime for hardware changes. The techniques involve use of such devices as inlet pressure distortion jets, a hydrogen burner for inlet temperature distortions, fan back pressure jets to simulate a variable area nozzle, and either an inflow-outflow bleed system or a fuel spurt system to alter compressor discharge pressure.

Biesiadny, T. J.↗
NASA NTRS1974

The M.I.T. Blowdown compressor facility

A blowdown compressor test facility has been developed which allows time-resolved aerodynamic testing of full-scale transonic compressor rotors at low cost. The rotor is brought to speed in vacuum, a diaphragm is opened, and the test gas is allowed to flow for a time of the order of 0.1 sec, during which the rotor is driven by its own inertia. Both 'steady-state' performance evaluation and detailed time resolution of the flow on the blade-passing time scale have been demonstrated for a two-ft-diam transonic rotor with a tangential Mach number of 1.2 and a nominal pressure ratio of 1.6. The steady-state performance as determined in the experiments includes an efficiency of 0.92 and a pressure ratio of 1.55 at design speed. The time-resolved measurements include the combination tone structure in the upstream flow field, resolved both axially and radially, and the wake structure downstream of the rotor, also resolved both radially and axially.

Kerrebrock, J. L.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors, part 8

An experimental investigation was conducted with an 0.8 hub/tip ratio, single-stage, axial flow compressor to determine the potential of tandem-airfoil blading for improving the efficiency and stable operating range of compressor stages. The investigation included testing of a baseline stage with single-airfoil blading and two tandem-blade stages. The overall performance of the baseline stage and the tandem-blade stage with a 20-80% loading split was considerably below the design prediction. The other tandem-blade stage, which had a rotor with a 50-50% loading split, came within 4.5% of the design pressure rise (delta P(bar)/P(bar) sub 1) and matched the design stage efficiency. The baseline stage with single-airfoil blading, which was designed to account for the actual rotor inlet velocity profile and the effects of axial velocity ratio and secondary flow, achieved the design predicted performance. The corresponding tandem-blade stage (50-50% loading split in both blade rows) slightly exceeded the design pressure rise but was 1.5 percentage points low in efficiency. The tandem rotors tested during both phases demonstrated higher pressure rise and efficiency than the corresponding single-airfoil rotor, with identical inlet and exit airfoil angles.

Brent, J. A.↗
NASA NTRS1975

Effect of inducer inlet and diffuser throat areas on performance of a low pressure ratio sweptback centrifugal compressor

A low-pressure-ratio centrifugal compressor was tested with nine combinations of three diffuser throat areas and three impeller inducer inlet areas which were 75, 100, and 125 percent of design values. For a given inducer inlet area, increases in diffuser area within the range investigated resulted in increased mass flow and higher peak efficiency. Changes in both diffuser and inducer areas indicated that efficiencies within one point of the maximum efficiency were obtained over a compressor specific speed range of 27 percent. The performance was analyzed of an assumed two-spool open-cycle engine using the 75 percent area inducer with a variable area diffuser.

Klassen, H. A.↗
NASA NTRS1975

Effect of inlet ingestion of a wing tip vortex on compressor face flow and turbojet stall margin

A two-dimensional inlet was alternately mated to a coldpipe plug assembly and a J85-GE-13 turbojet engine, and placed in a Mach 0.4 stream so as to ingest the tip vortex of a forward mounted wing. Vortex properties were measured just forward of the inlet and at the compressor face. Results show that ingestion of a wing tip vortex by a turbojet engine can cause a large reduction in engine stall margin. The loss in stall compressor pressure ratio was primarily dependent on vortex location and rotational direction and not on total-pressure distortion.

Mitchell, G. A.↗
NASA NTRS1974

Engineering report: Oxygen boost compressor study

An oxygen boost compressor is described which supports a self-contained life support system. A preliminary analysis of the compressor is presented along with performance test results, and recommendations for follow-on efforts.

Tera, L. S.↗
NASA NTRS1975

Evaluation of the electrochemical O2 concentrator as an O2 compressor

A program was successfully completed to analytically and experimentally evaluate the feasibility of using an electrochemical oxygen (O2) concentrator as an O2 compressor. The electrochemical O2 compressor (EOC) compresses 345 kN/sq m (50 psia) O2 generated on board the space vehicle by the water electrolysis subsystem (WES) in a single stage to 20,700 kN/sq m (3000 psia) to refill spent extravehicular equipment O2 bottles and to eliminate the need for high pressure O2 storage. The single cell EOC designed, fabricated, and used for the feasibility testing is capable of being tested at O2 pressures up to 41,400 kN/sq m (6000 psia). A ground support test facility to test the EOC cell was designed, fabricated, and used for the EOC feasibility testing. A product assurance program was established, implemented, and maintained which emphasized safety and materials compatibility associated with high pressure O2 operation. A membrane development program was conducted to develop a membrane for EOC application. Data obtained using a commercially available membrane were used to guide the development of the membranes fabricated specifically for an EOC. A total of 15 membranes were fabricated.

Marshall, R. D.↗
NASA NTRS1975

Composites for fans and compressors

The composites research being conducted at Lewis for the application of composite materials to fan and compressor blades, is reviewed. The major areas discussed include the development of improved materials and fabrication methods, recent progress in providing composite fan and compressor blades with improved resistance to foreign object damage, and the development of advanced design and analysis procedures for composite blades.

Serafini, T. T.↗
NASA NTRS1974

Test techniques for obtaining off-nominal compressor data during engine tests

Several unique techniques and related devices are in use at the Lewis Research Center for off-design testing of fan and compressor sections in full-scale jet engines. The devices presented not only permit a wide range of experimental conditions but also minimize downtime for hardware changes. The techniques involve use of such devices as inlet pressure distortion jets, a hydrogen burner for inlet temperature distortions, fan back pressure jets to simulate a variable area nozzle, and either an inflow-outflow bleed system or a fuel spurt system to alter compressor discharge pressure.

Biesiadny, T. J.↗
NASA NTRS1975

Electrochemical oxygen concentrator as an oxygen compressor

A solid polymer electrolyte (SPE) oxygen compressor is described which generates pressures of 3000 psi. The SPE is a cation exchange membrane with chemical compatibility, and has the capability of withstanding 5000 psi. Other features of the compressor described include: gasketless sealing, porus plate cell supports, and conductive cooling. Results are presented of a computer program which defines the power of the system as a function of density, temperature, pressure, membrane thickness, and water content.

Source record↗
NASA NTRS1976

Linearized blade row compression component model. Stability and frequency response analysis of a J85-3 compressor

NASA developed stability and frequency response analysis techniques were applied to a dynamic blade row compression component stability model to provide a more economic approach to surge line and frequency response determination than that provided by time-dependent methods. This blade row model was linearized and the Jacobian matrix was formed. The clean-inlet-flow stability characteristics of the compressors of two J85-13 engines were predicted by applying the alternate Routh-Hurwitz stability criterion to the Jacobian matrix. The predicted surge line agreed with the clean-inlet-flow surge line predicted by the time-dependent method to a high degree except for one engine at 94% corrected speed. No satisfactory explanation of this discrepancy was found. The frequency response of the linearized system was determined by evaluating its Laplace transfer function. The results of the linearized-frequency-response analysis agree with the time-dependent results when the time-dependent inlet total-pressure and exit-flow function amplitude boundary conditions are less than 1 percent and 3 percent, respectively. The stability analysis technique was extended to a two-sector parallel compressor model with and without interstage crossflow and predictions were carried out for total-pressure distortion extents of 180 deg, 90 deg, 60 deg, and 30 deg.

Tesch, W. A.↗
NASA NTRS1976

A real-time adaptive Hadamard transform video compressor

An adaptive video compressor was designed as part of the CTS Digital Video Curriculum Sharing Experiment. The compressor was constructed using field-to-field differencing on fields processed using a Hadamard transform method. The spatial resolution was improved using a fixed-rate, three-mode adaptive system to compress each field.

Jones, H. W., Jr.↗