Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffractometers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Effect Of Neodymium Substitution In Structural Characteristics Of Magnesium Ferrite

The effect of Nd{sup 3+} substitution on the structural properties of Magnesium ferrite was studied in the series MgNd{sub x}Fe{sub 2-x}O{sub 4}, where x = 0 to 0.3 in steps of 0.05. The series was prepared by sol-gel technique which is one of the novel technique to prepare nanosized samples. Structural characterization was done using X-ray diffractometer and Fourier Transform Infrared Spectrometer. XRD analysis reveals the prepared samples are single phasic till x = 0.2. From x0 = .25, a secondary phase of iron neodymium oxide appears along with the spinel phase. Particle size calculation shows the prepared samples are in the 9nm to 11 nm regime. Lattice parameter was found to increase with concentration of Nd. XRD and FTIR analysis confirmed spinel structure of the prepared samples. XRF result shows the expected composition of prepared samples. The frequency dependence of the dielectric constant in the range 100 Hz--120MHz was also studied

36 MATERIALS SCIENCE↗

Simultaneous detection of surface coverage and structure of krypton films on gold by helium atom diffraction and quartz crystal microbalance techniques

We describe a quartz crystal microbalance setup that can be operated at low temperatures in ultra high vacuum with gold electrode surfaces acting as substrate surface for helium diffraction measurements. By simultaneous measurement of helium specular reflection intensity from the electrode surface and resonance frequency shift of the crystal during film adsorption, helium diffraction data can be correlated to film thickness. In addition, effects of interfacial viscosity on the helium diffraction pattern could be observed. To this end, first, flat gold films on AT cut quartz crystals were prepared which yield high enough helium specular reflection intensity. Then the crystals were mounted in the helium diffractometer sample holder and driven by means of a frequency modulation driving setup. Different crystal geometries were tested to obtain the best quality factor and preliminary measurements were performed on Kr films on gold surfaces. While the crystal structure and coverage of krypton films as a function of substrate temperature could successfully be determined, no depinning effects could be observed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

{sup 3}He alternative technologies: 1. Application of neutron image plate detector for powder diffractometry

Neutron image plate was used for recording powder diffraction pattern from a polycrystalline Fe rod, mounted on the High Q Diffractometer at Dhruva reactor and using neutron beam of {lambda}= 0.783 A and {Phi}= 3 x 10{sup 5} n/cm{sup 2}/sec. The Bragg peaks were sharp and well resolved. The overall resolution ({Delta}2{theta}/2{theta}) value was found be {approx}0.025.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Structural and morphological properties of sputtered NiO thin films at various sputtering pressures

Nickel oxide thin films were successfully deposited on glass substrates at different sputtering pressures in the range of 3 x 10{sup -2} to 5 x 10{sup -2} mbar. It was observed that sputtering pressure influenced the structural and morphological properties. Structural properties were studied with X-ray diffractometer. All the deposited films were polycrystalline and exhibited cubic structure with preferential growth along (220) plane. From morphological studies it was observed that fine and uniform grains with RMS roughness of 9.4 nm were obtained when the films deposited at a sputtering pressure of 4 x 10{sup -2} mbar,. The grain size and the surface roughness decreased at higher sputtering pressures. The surface mobility of the adatoms decreased after series of collisions resulting in the decrease of grain size at high sputtering pressures.

36 MATERIALS SCIENCE↗

The precipitation synthesis of broad-spectrum UV absorber nanoceria

In this paper the possibility of nanoceria as broad-spectrum UV absorber was evaluated. Nanoceria were synthesized by precipitation process from cerium nitrate solution and ammonium hydroxide as precipitant agent. Isopropanol was mixed with water as solvent to prevent hard agglomeration. The structure of resulting nanoceria was characterized by x-ray diffractometer (XRD). The transparency in the visible light and efficiency of protection in UV A region were studied using ultraviolet-visible (UV - Vis) spectrophotometer. The results show that nanoceria possess good tranparency in visible light and high UV light absorption. The critical absorption wavelenght of 368 nm was obtained which is desirable for excellent broad-spectrum protection absorbers. Moreover, analysis of photodegradation nanoceria to methylene blue solution shows poor photocatalytic activity. It indicates that nanoceria suitable for used as UV absorber in personal care products.

36 MATERIALS SCIENCE↗

Investigation of site preference of Zn doped Ba{sub 3}Co{sub 2−x}Zn{sub x}Fe{sub 24}O{sub 41} by Mössbauer spectroscopy

The polycrystalline Ba{sub 3}Co{sub 2−x}Zn{sub x}Fe{sub 24}O{sub 41} (x = 0.0, 0.5, 1.0) samples were prepared by using solid-state-reaction method. The crystal structures and magnetic properties of samples were investigated with x-ray diffractometer, vibrating sample magnetometer, and Mössbauer spectroscopy. The crystal structure of Ba{sub 3}Co{sub 2−x}Zn{sub x}Fe{sub 24}O{sub 41} (x = 0.0, 0.5, 1.0) samples was determined to be a hexagonal structure with P6{sub 3}/mmc space group at 295 K, and the saturation magnetization (M{sub s}) of Ba{sub 3}Co{sub 2−x}Zn{sub x}Fe{sub 24}O{sub 41} (x = 0.0, 0.5, 1.0) samples were found to be M{sub s} = 50.9, 53.1, 55.0 emu/g, respectively. From the temperature dependence of magnetization curves under 100 Oe between 4.2 and 740 K, we were able to observe the spin transition, and both spin transition temperature (T{sub s}) and Curie temperature (T{sub C}) decrease with increasing Zn concentration. Mössbauer spectra of all samples were obtained and analyzed at various temperatures ranging from 4.2 to 295 K. With ten-sextets for Fe sites corresponding to the Z-type hexagonal crystallographic sites, all spectra below T{sub C} were fitted by least-square method. In addition, from the site occupation numbers of Fe, calculated from the relative areas fitted to the Mössbauer spectra, we find that Zn ions preferentially occupy the tetrahedral sublattices of down sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thickness dependent structural, optical and electrical properties of CuIn{sub 0.8}Ga{sub 0.2}Se{sub 2} thin films deposited by pulsed laser deposition

CuIn{sub 0.8}Ga{sub 0.2}Se{sub 2} (CIGS) polycrystalline thin films have been deposited on soda lime glass substrate at different deposition time by pulsed laser deposition. The effect of thickness on structural, surface morphological, optical and electrical properties of thin films were investigated by X-ray diffractometer (XRD), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), UV-Vis-NIR spectrophotometer and electrical measurement unit. XRD study reveals that all deposited films are polycrystalline in nature and have tetragonal phase of CIGS. Crystallinity of CIGS films has been found to improve with increase in thickness of CIGS films as evidenced by sharp XRD peaks for (112) orientation. Grain size and rms surface roughness of CIGS films have been found to be increased with increase in thickness. All the deposited CIGS films exhibit direct band gap semiconducting behaviour with ∼10{sup 6} cm{sup −1} absorption co-efficient. Optical band gap and resistivity of CIGS films have been found to decrease with increase in thickness.

36 MATERIALS SCIENCE↗

Single crystal structure analysis of a single Sm{sub 2}Fe{sub 17}N{sub 3} particle

We performed single crystal structure analysis of Sm{sub 2}Fe{sub 17}N{sub 3} using X-ray diffraction. A pick-up system combined with a micromanipulation tool driven by piezoelectric actuators and a microgripper was used. A single Sm{sub 2}Fe{sub 17}N{sub x} particle with the diameter of about 20 μm was picked up, and X-ray diffraction was measured using an X-ray diffractometer at the synchrotron radiation beamline at the Photon Factory, KEK. Single crystal structure analysis of a Sm{sub 2}Fe{sub 17}N{sub 3} particle was performed and the structure was successfully determined from X-ray diffraction patterns. The space group and the lattice constants were determined to be R-3m (number sign166) a = b = 8.7206 Å and c = 12.6345 Å, respectively. Atomic positions of Sm and Fe atoms were accurately determined by single crystal structure analysis of only one particle.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Polarity characterization by anomalous x-ray dispersion of ZnO films and GaN lateral polar structures

We demonstrate the use of anomalous x-ray scattering of constituent cations at their absorption edge, in a conventional Bragg-Brentano diffractometer, to measure absolutely and quantitatively the polar orientation and polarity fraction of unipolar and mixed polar wurtzitic crystals. In one set of experiments, the gradual transition between c+ and c− polarity of epitaxial ZnO films on sapphire as a function of MgO buffer layer thickness is monitored quantitatively, while in a second experiment, we map the polarity of a lateral polar homojunction in GaN. The dispersion measurements are compared with piezoforce microscopy images, and we demonstrate how x-ray dispersion and scanning probe methods can provide complementary information that can discriminate between polarity fractions at a material surface and polarity fractions averaged over the film bulk.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The crystal structure and magnetic properties of Ba{sub 2−x}Sr{sub x}Co{sub 2}Fe{sub 12}O{sub 22}

We have synthesized the Ba{sub 2−x}Sr{sub x}Co{sub 2}Fe{sub 12}O{sub 22} samples (x = 0.1, 0.2, 0.3, 0.4, 0.5) by the solid-state reaction method and investigated their crystalline and magnetic properties by X-ray diffractometer (XRD), Mössbauer spectrometer, vibrating sample magnetometer, and network analyzer. XRD patterns show that all samples are rhombohedral with space group R-3m. The lattice constants a{sub 0} and c{sub 0} decrease with Sr substitution due to smaller ion radius of Sr{sup 2+} (1.27 Å) than that of Ba{sup 2+} (1.43 Å). The Mössbauer spectroscopy measurements show that the relative area ratios of Fe ion were maintained constant regardless of the Sr concentration. However, average magnetic hyperfine field slightly increased with the Sr concentration. This observation agrees with the fact that the saturation magnetization (M{sub s}) linearly increases due to the increasing super-exchange interaction, originated from the difference in the ionic radius between Ba{sup 2+} and Sr{sup 2+}. To investigate its properties at high frequency range, all samples were sintered at 1100 °C, and complex permeability and permittivity were measured by network analyzer between 100 MHz and 4 GHz. For x below 0.3, the initial permeability at 100 MHz increases, at higher values of x, its value decreases. Our study shows that magnetic properties of Sr{sup 2+} substitution for Ba{sup 2+} in Y-type hexaferrite as well as low magnetic loss less than 0.1 in 1 GHz band, indicating the potential application of Ba{sub 2−x}Sr{sub x}Co{sub 2}Fe{sub 12}O{sub 22} samples for RF and antenna devices in ultra high frequency band.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electroplated L1{sub 0} CoPt thick-film permanent magnets

The fabrication and magnetic characterization of 15-μm-thick electroplated L1{sub 0} CoPt hard magnets with good magnetic properties is reported in this paper. Experimental study of the dependence of the magnets' properties on annealing temperature reveals that an intrinsic coercivity H{sub ci} = ∼800 kA/m (10 kOe), squareness >0.8, and energy product of >150 kJ/m{sup 3} are obtained for photolithographically patterned structures (250 μm × 2 mm stripes; 15 μm thickness) electroplated on silicon substrates and annealed in hydrogen forming gas at 700 °C. Scanning electron microscopy is used to inspect the morphology of both the as-deposited and annealed magnetic layers, and X-ray Diffractometer analysis on the magnets annealed at 700 °C confirm a phase transformation to an ordered L1{sub 0} CoPt structure, with a minor phase of hcp Co. These thick films are intended for microsystems/MEMS applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In situ X-ray investigation of changing barrier growth temperatures on InGaN single quantum wells in metal-organic vapor phase epitaxy

The effects of GaN quantum barriers with changing growth temperatures on the interfacial characteristics of GaN/InGaN single quantum well (SQW) grown on GaN templates by metalorganic vapour phase epitaxy were in situ investigated by X-ray crystal truncation rod (CTR) scattering and X-ray reflectivity measurements at growth temperature using a laboratory level X-ray diffractometer. Comparing the curve-fitting results of X-ray CTR scattering spectra obtained at growth temperature with that at room temperature, the In{sub x}Ga{sub 1-x}N with indium composition less than 0.11 was stabile of the indium distribution at the interface during the whole growth processes. By using several monolayers thickness GaN capping layer to protect the InGaN well layer within temperature-ramping process, the interfacial structure of the GaN/InGaN SQW was drastically improved on the basis of the curve-fitting results of X-ray CTR scattering spectra, and the narrow full width at half-maximum and strong luminous intensity were observed in room temperature photoluminescence spectra.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic properties of Nd-Ga-Fe{sub bal}-Nb-B alloy

Here, we have synthesized Nd-Ga-Fe{sub bal}-Nb-B alloy by strip casting method. The crystalline and magnetic properties of sample were investigated with x-ray diffractometer (XRD), vibrating sample magnetometer (VSM), and Mössbauer spectrometer. The XRD pattern was analyzed with the Rietveld refinement method, indicating a tetragonal structure and the space group of P4{sub 2}/mnm. The temperature dependence of zero-field cooled (ZFC) magnetization curve was measured under applied field at temperature ranging from 4.2 to 740 K. From the ZFC curve, Curie temperature and spin reorientation temperature are determined to be 615 K and 130 K, respectively. Also, Mössbauer spectra were measured at various temperatures ranging from 4.2 to 620 K. Each spectrum was fitted with 6-sextets for Fe site (8j{sub 1}, 8j{sub 2}, 16k{sub 1}, 16k{sub 2}, 4c, and 4e), and magnetic hyperfine field, Isomer shift, electric quadrupole shift, and area ratio values were obtained from the fit. We observed the change in slope of magnetic hyperfine field and electric quadrupole shift at 130 K while the Curie temperature was determined to be 615 K from the measurement of zero velocity counter, agreeing with the values obtained from VSM measurements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature dependent DC electrical conductivity studies of ZnO nanoparticle thick films prepared by simple solution combustion method

ZnO nanoparticles of different size were prepared by varying the molar ratio of glycine and zinc nitrate hexahydrate as fuel and oxidizer (F/O = 0.8, 1.11, 1.7) by simple solution combustion method. Powder samples were characterized by UV-Visible spectrophotometer, X-ray diffractometer, Scanning electron microscope (SEM). DC electrical conductivity measurements at room temperature and in the temperature range of 313-673K were carried out for the prepared thick films and it was found to increase with increase of temperature which confirms the semiconducting nature of the samples. Activation energies were calculated and it was found that, F/O molar ratio 1.7 has low E{sub AL} (Low temperature activation energy) and high E{sub AH} (High temperature activation energy) compared to other samples.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Growth of vertically aligned α−MoO{sub 3} nanoflakes by using a facile PVD route

In this report, we synthesize vertically aligned molybdenum trioxide (α−MoO{sub 3}) nanoflakes (NFs) with high aspect ratio (height/thickness >15) on the cobalt coated glass substrates by the plasma assisted sublimation process, employing Mo metal strip as a sublimation source. The effect of substrate temperature, nature of substrate as well as the geometry of the sublimation source (Mo-strip) have been investigated on the morphological, structural and optical properties of the grown NFs, keeping plasma parameters as fixed. The surface morphology, crystalline structure and optical properties of MoO{sub 3} NFs have been studied systematically by using scanning electron microscope (SEM), transmission electron microscope (TEM) with selected area electron diffraction (SAED), X-ray diffractometer, and IR- spectroscopy. The experimental observations endorse that the characteristics of MoO{sub 3} NFs are strongly depend on substrate temperature, substrate nature as well as geometry of Mo-strip. All the observed results are well in consonance with each other.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Response of nickel surface to pulsed fusion plasma radiations

Nickel based alloys are being projected as suitable materials for some components of the next generation fusion reactor because of compatible thermal, electrical and mechanical properties. Pure nickel material is tested here for possibility of similar application purpose. Nickel samples (> 99.5 % purity) are exposed here to plasma radiations produced due to D-D fusion reaction inside an 11.5 kJ plasma focus device. The changes in the physical properties of the nickel surface at microscopic level which in turn change the mechanical properties are analyzed using scanning electron microscope, optical microscope, glancing incident X-ray diffractometer and Vicker's hardness gauge. The results are reported here.

36 MATERIALS SCIENCE↗

Investigation of variation of energy of laser beam on structural, electrical and optical properties of pulsed laser deposited CuO thin films

In this paper, copper oxide (CuO) thin films have been deposited successfully by pulsed laser deposition technique using copper metal as target material. Thin films have been prepared under different energy of laser pulses ranging from 100mJ/pulse to 250 mJ/pulse. These films have been characterized for their structural, electrical and optical properties by using X-Ray Diffractometer (XRD), Four probe method and UV spectroscopy. Morphological and structural studies show that there is increase in crystallite size with the increase in energy of laser beam. Thus resulting in improved crystallinity and degree of orientation of the CuO thin films. Optoelectrical properties show direct relation between conductivity and energy of laser beam. Optical analysis of CuO thin films prepared under different energy of laser beam shows good agreement with structural analysis. The prepared CuO thin films show high absorbance in the UV and visible range and thus are suitable candidate for thin films solar cell application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Neutron diffraction studies for realtime leaching of catalytic Ni

The leaching of Al from intermetallic samples of Nickel Aluminium alloys to form Raney-type nickel catalysts is widely used in the hydrogenation industry, however, little is known of the leaching process itself. In this study, the leaching of Al was measured in realtime, in situ, using the high-flux powder neutron diffractometer, D20, at the Institut Laue-Langevin. Despite the liberation of hydrogen and effervescent nature of the reaction the transformation of the dry powder phases into Raney-type Ni was determined. Samples produced by gas-atomisation were found to leach faster than those produced using the cast and crushed technique. Regardless of processing route of the precursor powder, the formation of spongy-Ni occurs almost immediately, while Ni{sub 2}Al{sub 3} and NiAl{sub 3} continue to transform over longer periods of time. Small-angle scattering and broadening of the diffraction peaks is an evidence for the formation of the smaller Ni particles. Understanding the kinetics of the leaching process will allow industry to refine production of catalysts for optimum manufacturing time while knowledge of leaching dynamics of powders produced by different manufacturing techniques will allow further tailoring of catalytic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗