Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffuser Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Comparative Kinetic Analysis of Closed-Ended and Open-Ended Porous Sensors

Efficient mass transport through porous networks is essential for achieving rapid response times in sensing applications utilizing porous materials. In this work, we show that open-ended porous membranes can overcome diffusion challenges experienced by closed-ended porous materials in a microfluidic environment. A theoretical model including both transport and reaction kinetics is employed to study the influence of flow velocity, bulk analyte concentration, analyte diffusivity, and adsorption rate on the performance of open-ended and closed-ended porous sensors integrated with flow cells. The analysis shows that open-ended pores enable analyte flow through the pores and greatly reduce the response time and analyte consumption for detecting large molecules with slow diffusivities compared with closed-ended pores for which analytes largely flow over the pores. Experimental confirmation of the results was carried out with open- and closed-ended porous silicon (PSi) microcavities fabricated in flow-through and flow-over sensor configurations, respectively. The adsorption behavior of small analytes onto the inner surfaces of closed-ended and open-ended PSi membrane microcavities was similar. However, for large analytes, PSi membranes in a flow-through scheme showed significant improvement in response times due to more efficient convective transport of analytes. The experimental results and theoretical analysis provide quantitative estimates of the benefits offered by open-ended porous membranes for different analyte systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Large Eddy Simulation of a Supercritical Fuel Jet in Cross Flow using GPU-Acceleration

Fuel is routinely injected into combustion chambers at elevated pressures resulting in formation of supercritical fluid flow. The dispersion of fuel and the combustion processes are significantly different in high pressure conditions as the raditional liquid atomization and evaporation are replaced by diffusion-dominated mixing. Modeling supercritical flow is challenging due to the complex thermodynamics and transport properties of the fluids and in most cases high fidelity numerical simulations are prohibitively expensive. However, numerical investigations must incorporate the flow properties appropriate for the regime for accurate description of the physical processes involved. In this paper, we consider real-fluid properties and simulate the turbulent mixing of fuel jet in cross flow at high ambient pressure. In order to make efficient use of the computer resources and reduce the time to solution, without compromising the resolution requirements, the real-fluid property routines are accelerated via Graphics Processing Unit (GPU) computation. The numerical simulations performed at different resolutions suggest that the high fidelity computations with refined mesh are essential to capture the non-linear dynamics of vortex evolution downstream of the fuel jet and signifies the necessity for an accelerated code. The code is accelerated using the Kokkos C++ library and is demonstrated to be about 2 times faster than the non-accelerated version. Considerable computational cost associated with the thermodynamics routines is reduced in the accelerated version. The results also suggest the resource requirements to compute turbulent closures and the need for acceleration of the routines associated with the sub-grid scale closures.

Gottiparthi, Kalyana C.↗

Coupling compositional liquid gas Darcy and free gas flows at porous and free-flow domains interface

This paper proposes an efficient splitting algorithm to solve coupled liquid gas Darcy and free gas flows at the interface between a porous medium and a free-flow domain. This model is compared to the reduced model introduced in [6] using a 1D approximation of the gas free flow. For that purpose, the gas molar fraction diffusive flux at the interface in the free-flow domain is approximated by a two point flux approximation based on a low-frequency diagonal approximation of a Steklov–Poincaré type operator. The splitting algorithm and the reduced model are applied in particular to the modelling of the mass exchanges at the interface between the storage and the ventilation galleries in radioactive waste deposits.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The density and velocity of plasma bullets propagating along one dielectric tube

This study shows that the propagation of plasma bullets along one dielectric tube is strongly affected by many discharge parameters, such as the waveform of applied voltage (AC or pulsed DC), peak voltage, He flow rate, and the frequency of AC voltage. Analysis indicates that the density and velocity of plasma bullets are mainly determined by the electric field at the front of plasma bullets. These discharge parameters may significantly influence the distribution of plasma potential along the tube, thus control the electric field at the front of plasma bullets and their propagation. An increase in the pulsed DC voltage with its rise time of <40-50 ns can lead to an obvious improvement in the electric field at the front of plasma bullets, resulting in generation of a plasma in the high density gas and a fast propagation of plasma bullets. He flowing through the tube can contribute to the surface diffusion of charged species, and greatly increase the electric field at the front of plasma bullets. During the propagation of plasma bullets, their density is decreased due to the surface recombination of charged species, such as electrons and ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Biomass drying in a pulsed fluidized bed without inert bed particles

Batch drying was performed in the pulsed fluidized bed with various species of biomass particles as an indicator of gas–solid contact efficiency and mass transfer rate under different operating conditions including pulsation duty cycle and particle size distribution. The fluidization of cohesive biomass particles benefited from the shorter opening time of pulsed gas flow and increased peak pressure drop. The presence of fines enhanced gas–solid contact of large and irregular biomass particles, as well as the mass transfer efficiency. A drying model based on two-phase theory was proposed, from which effective diffusivity was calculated for various gas flow rates, temperature and pulsation frequency. Intricate relationship was discovered between pulsation frequency and effective diffusivity, as mass transfer was deeply connected with the hydrodynamics. Effective diffusivity was also found to be proportional to gas flow rate and drying temperature. In conclusion, operating near the natural frequency of the system also favored drying and mass transfer.

09 BIOMASS FUELS↗

Multiscale dendritic needle network model of alloy solidification with fluid flow

We present a mathematical formulation of a multiscale model for solidification with convective flow in the liquid phase. The model is an extension of the dendritic needle network approach for crystal growth in a binary alloy. We propose a simple numerical implementation based on finite differences and step-wise approximations of parabolic dendritic branches of arbitrary orientation. Results of the two-dimensional model are verified against reference benchmark solutions for steady, unsteady, and buoyant flow, as well as steady-state dendritic growth in the diffusive regime. Simulations of equiaxed growth under forced flow yield dendrite tip velocities within 10% of quantitative phase-field results from the literature. Finally, we perform illustrative simulations of polycrystalline solidification using physical parameters for an aluminum-10wt% copper alloy. Resulting microstructures show notable differences when taking into account natural buoyancy in comparison to a purely diffusive transport regime. The resulting model opens new avenues for computationally and quantitatively investigating the influence of fluid flow and gravity-induced buoyancy upon the selection of dendritic microstructures. Further ongoing developments include an equivalent formulation for directional solidification conditions and the implementation of the model in three dimensions, which is critical for quantitative comparison to experimental measurements.

36 MATERIALS SCIENCE↗

THEORY OF SOLAR MERIDIONAL CIRCULATION AT HIGH LATITUDES

We build a hydrodynamic model for computing and understanding the Sun's large-scale high-latitude flows, including Coriolis forces, turbulent diffusion of momentum, and gyroscopic pumping. Side boundaries of the spherical 'polar cap', our computational domain, are located at latitudes {>=} 60 Degree-Sign . Implementing observed low-latitude flows as side boundary conditions, we solve the flow equations for a Cartesian analog of the polar cap. The key parameter that determines whether there are nodes in the high-latitude meridional flow is {epsilon} = 2{Omega}n{pi}H{sup 2}/{nu}, where {Omega} is the interior rotation rate, n is the radial wavenumber of the meridional flow, H is the depth of the convection zone, and {nu} is the turbulent viscosity. The smaller the {epsilon} (larger turbulent viscosity), the fewer the number of nodes in high latitudes. For all latitudes within the polar cap, we find three nodes for {nu} = 10{sup 12} cm{sup 2} s{sup -1}, two for 10{sup 13}, and one or none for 10{sup 15} or higher. For {nu} near 10{sup 14} our model exhibits 'node merging': as the meridional flow speed is increased, two nodes cancel each other, leaving no nodes. On the other hand, for fixed flow speed at the boundary, as {nu} is increased the poleward-most node migrates to the pole and disappears, ultimately for high enough {nu} leaving no nodes. These results suggest that primary poleward surface meridional flow can extend from 60 Degree-Sign to the pole either by node merging or by node migration and disappearance.

79 ASTRONOMY AND ASTROPHYSICS↗

Self-diffusion in the non-Newtonian regime of shearing liquid crystal model systems based on the Gay-Berne potential

The self-diffusion coefficients of nematic phases of various model systems consisting of regular convex calamitic and discotic ellipsoids and non-convex bodies such as bent-core molecules and soft ellipsoid strings have been obtained as functions of the shear rate in a shear flow. Then the self-diffusion coefficient is a second rank tensor with three different diagonal components and two off-diagonal components. These coefficients were found to be determined by a combination of two mechanisms, which previously have been found to govern the self-diffusion of shearing isotropic liquids, namely, (i) shear alignment enhancing the diffusion in the direction parallel to the streamlines and hindering the diffusion in the perpendicular directions and (ii) the distortion of the shell structure in the liquid whereby a molecule more readily can escape from a surrounding shell of nearest neighbors, so that the mobility increases in every direction. Thus, the diffusion parallel to the streamlines always increases with the shear rate since these mechanisms cooperate in this direction. In the perpendicular directions, these mechanisms counteract each other so that the behaviour becomes less regular. In the case of the nematic phases of the calamitic and discotic ellipsoids and of the bent core molecules, mechanism (ii) prevails so that the diffusion coefficients increase. However, the diffusion coefficients of the soft ellipsoid strings decrease in the direction of the velocity gradient because the broadsides of these molecules are oriented perpendicularly to this direction due the shear alignment (i). The cross coupling coefficient relating a gradient of tracer particles in the direction of the velocity gradient and their flow in the direction of the streamlines is negative and rather large, whereas the other coupling coefficient relating a gradient in the direction of the streamlines and a flow in the direction of the velocity gradient is very small.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A higher‐order unsplit 2D direct Eulerian finite volume method for two‐material compressible flows based on the MOOD paradigms

SUMMARY A higher‐order unsplit multi‐dimensional discretization of the diffuse interface model for two‐material compressible flows proposed by R. Saurel, F. Petitpas and R. A. Berry in 2009 is developed. The proposed higher‐order method is based on the concepts of the Multidimensional Optimal Order Detection (MOOD) method introduced in three recent papers for single‐material flows. The first‐order unsplit multi‐dimensional Finite Volume discretization presented by SPB serves as foundation for the development of the higher‐order unlimited schemes. Specific detection criteria along with a novel decrementing algorithm for the MOOD method are designed in order to deal with the complexity of multi‐material flows. Numerically, we compare errors and computational times on several 1D problems (stringent shock tube and cavitation problems) computed on 2D meshes with the second‐ and fourth‐order MOOD methods using a classical MUSCL method as reference. Several simulations of a 2D shocked R22 bubble in the air are also presented on Cartesian and unstructured meshes with the second‐ and fourth‐order MOOD methods, and qualitative comparisons confirm the conclusions obtained with 1D problems. These numerical results demonstrate the robustness of the MOOD approach and the interest of using more than second‐order methods even for locally singular solutions of complex physics models. Copyright © 2014 John Wiley & Sons, Ltd.

Diot, S.↗

Numerical Evaluation of Unsaturated-Zone Flow and Transport Pathways at Rainier Mesa, Nevada

Sixty-one underground nuclear tests were conducted at Rainier Mesa at the Nevada National Security Site between 1957 and 1992. The mesa includes the highest-elevation areas at the Nevada National Security Site and experiences some of the highest estimated infiltration rates. Perched water is ubiquitous in many of the tunnels used for testing. The presence of sloping layers with strongly varying degrees of fracturing and overall permeability suggests that some infiltrating water may be diverted laterally along higher-permeability layers, thereby reducing overall percolation flux and radionuclide transport through the low-permeability testing horizons but also potentially transporting radionuclides laterally away from the test locations. A high-resolution, two-dimensional, cross-sectional model was created to simulate water and particle movement along potential lateral flow paths and to investigate flow and transport paths within and surrounding the perched water bodies. The model results indicate that particles with starting locations within the low-permeability perching layers will follow dominantly vertical trajectories through the perching horizons and reach the water table in the underlying carbonate aquifer only after many thousands of years. In contrast, particles starting near ground surface above the testing horizon are mostly diverted laterally before reaching the testing horizon, except where nearby faults through the perching layers are present. Where the rock above the perching horizon is fractured, particles originating near ground surface can move laterally with relatively high transport velocities. Transport calculations for 3 H show that transport extent is limited by slow matrix flow, radioactive decay, and matrix diffusion in the fractured units.

54 ENVIRONMENTAL SCIENCES↗

Insight from simulations of single-well injection-withdrawal tracer tests on simple and complex fractures

The single-well injection withdrawal (SWIW) test, a tracer test utilizing only one well, is proposed as a useful contribution to site characterization of fractured rock, as well as providing parameters relevant to tracer diffusion and sorption. The usual conceptual model of flow and solute transport through fractured rock with low matrix permeability involves solute advection and dispersion through a fracture network coupled with diffusion and sorption into the surrounding rock matrix. Unlike two-well tracer tests, results of SWIW tests are ideally independent of advective heterogeneity, channeling and flow dimension, and, instead, focus on diffusive and sorptive characteristics of tracer (solute) transport. Thus, they can be used specifically to study such characteristics and evaluate the diffusive parameters associated with tracer transport through fractured media. We conduct simulations of SWIW tests on simple and complex fracture models, the latter being defined as having two subfractures with altered rock blocks in between and gouge material in their apertures. Using parameters from the Aspo site in Sweden, we calculate and study SWIW tracer breakthrough curves (BTCs) from a test involving four days of injection and then withdrawal. By examining the peak concentration C{sub pk} of the SWIW BTCs for a variety of parameters, we confirm that C{sub pk} is largely insensitive to the fracture advective flow properties, in particular to permeability heterogeneity over the fracture plane or to subdividing the flow into two subfractures in the third dimension orthogonal to the fracture plane. The peak arrival time t{sub pk} is not a function of fracture or rock properties, but is controlled by the time schedule of the SWIW test. The study shows that the SWIW test is useful for the study of tracer diffusion-sorption processes, including the effect of the so-called flow-wetted surface (FWS) of the fracture. Calculations with schematic models with different FWS values are conducted and the possibility of direct in situ measurement of FWS with SWIW tests is demonstrated.

54 ENVIRONMENTAL SCIENCES↗

Process and apparatus for separation of components of a gas stream

A process and apparatus for separating a gas mixture comprising providing a slot in a gas separation channel (conceptualized as a laterally elongated Clusius-Dickel column), having a length through which a net cross-flow of the gas mixture may be established; applying a higher temperature to one side of the channel and a lower temperature on an opposite side of the channel thereby causing thermal-diffusion and buoyant-convection flow to occur in the slot; and establishing a net cross-flow of a gas mixture comprising at least one higher density gas component and at least one lower density gas component along the length of the slot, wherein the cross-flow causes, in combination with the convection flow, a spiraling flow in the slot; and wherein the spiral flow causes an increasing amount of separation of the higher density gas from the lower density gas along the length of the channel. The process may use one or more slots and/or channels.

47 OTHER INSTRUMENTATION↗

Process and apparatus for separation of components of a gas stream

A process and apparatus for separating a gas mixture comprising providing a slot in a gas separation channel (conceptualized as a laterally elongated Clusius-Dickel column), having a length through which a net cross-flow of the gas mixture may be established; applying a higher temperature to one side of the channel and a lower temperature on an opposite side of the channel thereby causing thermal-diffusion and buoyant-convection flow to occur in the slot; and establishing a net cross-flow of a gas mixture comprising at least one higher density gas component and at least one lower density gas component along the length of the slot, wherein the cross-flow causes, in combination with the convection flow, a spiraling flow in the slot; and wherein the spiral flow causes an increasing amount of separation of the higher density gas from the lower density gas along the length of the channel. The process may use one or more slots and/or channels.

47 OTHER INSTRUMENTATION↗

Process and apparatus for separation of components of a gas stream

A process and apparatus for separating a gas mixture comprising providing a slot in a gas separation channel (conceptualized as a laterally elongated Clusius-Dickel column), having a length through which a net cross-flow of the gas mixture may be established; applying a higher temperature to one side of the channel and a lower temperature on an opposite side of the channel thereby causing thermal-diffusion and buoyant-convection flow to occur in the slot; and establishing a net cross-flow of a gas mixture comprising at least one higher density gas component and at least one lower density gas component along the length of the slot, wherein the cross-flow causes, in combination with the convection flow, a spiraling flow in the slot; and wherein the spiral flow causes an increasing amount of separation of the higher density gas from the lower density gas along the length of the channel. The process may use one or more slots and/or channels.

42 ENGINEERING↗

Immobile Pore-Water Storage Enhancement and Retardation of Gas Transport in Fractured Rock

The effect of immobile pore-water on gas transport in fractured rock has implications for numerical modeling of soil vapor extraction, methane leakage, gaseous CO 2 leakage from sequestration operations, radionuclide transport from underground nuclear explosions, and nuclear waste disposal. While the ability for immobile pore-water storage to effect gas transport has been recognized in the past, the details and specific scenarios leading to enhanced, retarded, or unaffected gas transport have not been explored. In this paper, we performed numerical investigations into the enhancement and retardation of gas transport due to immobile pore-water storage in order to identify implications for gas transport applications. To do this, we developed a numerical approach to model gas transport with a single-phase flow solution coupled to the advection–dispersion equation modified to account for immobile pore-water storage. Other than the immobility of pore water, the formulation contains all other physics included in two-phase formulations (advective and diffusive gas transport in fractures and rock matrix and dissolution in immobile pore water). The assumption of immobile pore water is valid here since for many applications involving transport of soluble gases in fractured rock, the rate of aqueous transport is insignificant compared to gas transport. We verify our modeling approach with analytical solutions of: (1) 1D gas diffusion, (2) 1D gas advection, (3) barometric pumping of a fracture, and (4) gas transport with uniform fracture flow and diffusion into the matrix. We account for pore-water storage in our model by implementing a kinetic formulation of gas dissolution wherein the dissolved (aqueous) phase is considered an immobile constituent. Using this formulation, we model the effect of dissolution rate and saturation on the retardation of gas transport during pure diffusion and pure advection. We also demonstrate that although it is commonly believed that pore-water storage will always enhance gas transport in fractures during oscillatory flow (e.g., during reversing pressure gradients such as barometric pumping cycles), our simulations indicate that this may not always be the case. Our numerical investigations indicate that scenarios with lower effective diffusion coefficients ( &#x2A85;<!-- <≈ --> 10 &#x2212;<!-- - --> 5 &#xA0;m 2 / s ) and lower dissolution coefficients (i.e., the dissolution diffusion coefficient) ( &#x2A85;<!-- <≈ --> 10 &#x2212;<!-- - --> 11 &#xA0;m 2 / s ) will result in enhanced gas transport. Other combinations of gaseous diffusion and dissolution coefficients result in delayed gas transport or insignificant effect on gas transport. Based on these results, and given the fact that the free-air diffusion coefficients for many gases are slightly above 10 &#x2212;<!-- - --> 5 &#xA0;m 2 / s (near the boundary of enhanced/non-enhanced gas transport), tortuosity would have to be significant for gas transport enhancement to occur. Similarly, if we consider the free-water diffusion coefficient of gases (around 10 &#x2212;<!-- - --> 9 &#xA0;m 2 / s for many gases of interest) to be a maximum bound for the effective dissolution coefficients (i.e., the rate of diffusion into the water away from the air/water interface will limit the dissolution rate), the effective dissolution coefficient would have to be at least 2 orders of magnitude less for enhanced gas transport to occur. Otherwise, pore-water storage will delay or have negligible effect on the gas transport. The results also indicate that the assumption of instantaneous equilibrium, often invoked in numerical codes for dissolution processes (i.e., dissolution coefficient is effectively infinite), will fail to accurately capture important details of soluble gas transport. Finally, the implication of our results is that gas breakthrough times in fractured rock during oscillatory flow may be highly dependent on the effective gaseous diffusion and dissolution coefficients.

58 GEOSCIENCES↗

AN EXPLICIT SCHEME FOR INCORPORATING AMBIPOLAR DIFFUSION IN A MAGNETOHYDRODYNAMICS CODE

We describe a method for incorporating ambipolar diffusion in the strong coupling approximation into a multidimensional magnetohydrodynamic (MHD) code based on the total variation diminishing scheme. Contributions from ambipolar diffusion terms are included by explicit finite-difference operators in a fully unsplit way, maintaining second-order accuracy. The divergence-free condition of magnetic fields is exactly ensured at all times by a flux-interpolated constrained transport scheme. The super time-stepping method is used to accelerate the time step in high-resolution calculations and/or in strong ambipolar diffusion. We perform two test problems, the steady-state oblique C-type shocks and the decay of Alfven waves, confirming the accuracy and robustness of our numerical approach. Results from the simulations of the compressible MHD turbulence with ambipolar diffusion show the flexibility of our method as well as its ability to follow complex MHD flows in the presence of ambipolar diffusion. These simulations show that the dissipation rate of the MHD turbulence is strongly affected by the strength of ambipolar diffusion.

79 ASTRONOMY AND ASTROPHYSICS↗

Resolving Losses at the Negative Electrode in All-Vanadium Redox Flow Batteries Using Electrochemical Impedance Spectroscopy

We present an in situ electrochemical technique for the quantitative measurement and resolution of the ohmic, charge transfer and diffusion overvoltages at the negative electrode of an all-vanadium redox flow battery (VRFB) using electrochemical impedance spectroscopy (EIS). The mathematics describing the complex impedance of the V+2/V+3 redox reaction is derived and matches the experimental data. The voltage losses contributed by each process have been resolved and quantified at various flow rates and electrode thicknesses as a function of current density during anodic and cathodic polarization. The diffusion overvoltage was affected strongly by flow rate while the charge transfer and ohmic losses were invariant. On the other hand, adopting a thicker electrode significantly changed both the charge transfer and diffusion losses due to increased surface area. Furthermore, the Tafel plot obtained from the impedance resolved charge transfer overvoltage yielded the geometric exchange current density, anodic and cathodic Tafel slopes (135 5 and 121 5 mV/decade respectively) and corresponding transfer coefficients = 0.45 0.02 and = 0.50 0.02 in an operating cell.

complex impedance↗

The Thermal Response of a Packed Bed Thermal Energy Storage System upon Saturated Steam Injection Using Distributed Temperature Sensing

The effectiveness of a thermal energy storage (TES) system is typically characterized with the help of thermal stratification or temperature gradients along the direction of heat injection, which is typically the flow direction of heat transfer fluid. The steepness of temperature gradients are a direct indicator of the effectiveness or efficiency of the heat storage or dispatch process. The temperature gradient evolution along the packed bed of ceramic particles upon saturated steam injection is presented in this work. Distributed temperature sensing based on optical frequency domain reflectometry was deployed in a packed bed of ceramic particles to capture the thermal front evolution in the axial direction. The physical processes accompanying steam injection in packed beds are complex due to phase change, transitioning two-phase flow, and changes in condensate accumulation. Therefore, the variation of thermal response of the TES system for various steam injection flow rates was experimentally studied using a high-resolution distributed temperature sensing system in a chemically inert alumina particle-packed bed. Distinct zones of different heat transfer modes were observed during the steam injection experiments. A distinct conduction zone, evident from diffuse thermal fronts, was observed at low flow rates, and these thermal gradients became sharper as the flow rate increased. The diffuse thermal fronts in the heat storage media suggest a low exergy efficiency of the TES system, as energy losses started initiating before a significant fraction of the bed was saturated with steam.

25 ENERGY STORAGE↗