SEARCH · Search NASA

Results for “Distributed temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1983

The use of heterodyne speckle photogrammetry to measure high-temperature strain distributions

Thermal and mechanical strains have been measured on samples of a common material used in jet engine burner liners, which were heated from room temperature to 870 C and cooled back to 220 C, in a laboratory furnace. The physical geometry of the sample surface was recorded to select temperatures by means of a set of twelve single-exposure specklegrams. Sequential pairs of specklegrams were compared in a heterodyne interferometer which allowed high-precision measurement of differential displacements. Good speckle correlation was observed between the first and last specklegrams also, which showed the durability of the surface microstructure, and permitted a check on accumulated errors. Agreement with calculated thermal expansion was to within a few hundred microstrain over a range of fourteen thousand.

Stetson, K. A.↗

NASA NTRS2021

Chandra Grating Spectroscopy of Embedded Wind Shock X-ray Emission from O Stars Shows Low Plasma Temperatures and Significant Wind Absorption

We present a uniform analysis of six examples of embedded wind shock (EWS) O star X-ray sources observed at high resolution with the Chandra grating spectrometers. By modeling both the hot plasma emission and the continuum absorption of the soft X-rays by the cool, partially ionized bulk of the wind we derive the temperature distribution of the shock-heated plasma and the wind mass-loss rate of each star. We find a similar temperature distribution for each star’s hot wind plasma, consistent with a power-law differential emission measure, dlogEMdlogT, with a slope a little steeper than -2, up to temperatures of only about107K. The wind mass-loss rates, which are derived from the broadband X-ray absorption signatures in the spectra, are consistent with those found from other diagnostics. The most notable conclusion of this study is that wind absorption is a very important effect, especially at longer wavelengths. More than 90 per cent of the X-rays between 18 and 25 ̊A produced by shocks in the wind of ζPup are absorbed, for example. It appears that the empirical trend of X-ray hardness with spectral subtype among O stars is primarily an absorption effect.

David H Cohen↗

NASA NTRS1971

AUTOTEM - Automated geometry meshing and heat conduction calculation

Temperature distribution for an arbitrary irregular body is calculated by AUTOTEM, which generates required input data automatically by computer. Temperature distribution is calculated for a two-dimensional plane section in /x,y/ coordinates or for an axisymmetric irregular body in /r,z/ coordinates.

Lee, A. Y.↗

NASA NTRS1974

Numerical and experimental studies of the natural convection within a horizontal cylinder

Numerical solutions are obtained for the quasi-compressible Navier-Stokes equations governing the time-dependent natural convection within a horizontal cylinder. The early flow development and wall heat transfer are obtained after a uniformly cold wall is imposed as a boundary condition on the cylinder. Results are also obtained for a time-varying cold wall as a boundary condition with windward explicit differencing used for the numerical solutions. The viscous truncation error associated with this scheme is controlled so that first-order accuracy is maintained in time and space. Experiments within a small-scale instrumented horizontal cylinder revealed the time development of the temperature distribution across the boundary layer as well as the decay of wall heat transfer with time. Agreement between temperature distributions obtained experimentally and numerically was generally good. The time decay of the dimensionless ratio of the Nusselt number to the one-fourth power of the Grashof number is found both numerically and experimentally, and good agreement is obtained between these two results over most of the cylinder wall.

Stewart, R. B.↗

NASA NTRS1998

Frequency-Domain Analysis of Diffusion-Cooled Hot-Electron Bolometer Mixers

A new theoretical model is introduced to describe heterodyne mixer conversion efficiency and noise (from thermal fluctuation effects) in diffusion-cooled superconducting hot-electron bolometers. The model takes into account the non-uniform internal electron temperature distribution generated by Wiedemann-Franz heat conduction, and accepts for input an arbitrary (analytical or experimental) superconducting resistance-versus- temperature curve. A non-linear large-signal solution is solved iteratively to calculate the temperature distribution, and a linear frequency-domain small-signal formulation is used to calculate conversion efficiency and noise. In the small-signal solution the device is discretized into segments, and matrix algebra is used to relate the heating modulation in the segments to temperature and resistance modulations. Matrix expressions are derived that allow single-sideband mixer conversion efficiency and coupled noise power to be directly calculated. The model accounts for self-heating and electrothermal feedback from the surrounding bias circuit.

Skalare, A.↗

NASA NTRS1991

Regional climate change predictions from the Goddard Institute for Space Studies high resolution GCM

A new diagnostic tool is developed for examining relationships between the synoptic scale circulation and regional temperature distributions in GCMs. The 4 x 5 deg GISS GCM is shown to produce accurate simulations of the variance in the synoptic scale sea level pressure distribution over the U.S. An analysis of the observational data set from the National Meteorological Center (NMC) also shows a strong relationship between the synoptic circulation and grid point temperatures. This relationship is demonstrated by deriving transfer functions between a time-series of circulation parameters and temperatures at individual grid points. The circulation parameters are derived using rotated principal components analysis, and the temperature transfer functions are based on multivariate polynomial regression models. The application of these transfer functions to the GCM circulation indicates that there is considerable spatial bias present in the GCM temperature distributions. The transfer functions are also used to indicate the possible changes in U.S. regional temperatures that could result from differences in synoptic scale circulation between a 1XCO2 and a 2xCO2 climate, using a doubled CO2 version of the same GISS GCM.

Crane, Robert G.↗

NASA NTRS1994

Constraining circumstellar environments: Far-infrared observations of Herbig Ae/Be stars

We have observed six Herbig Ae/Be stars at 50 and 100 microns with the Kuiper Airborne Observatory (KAO). All were classified as group I sources by Hillenbrand et al., signifying that their spectral energy distributions could be modeled with stars surrounded only by accretion disks. If the far-infrared emission is assumed to arise in a disk, it should be unresolved at 100 microns, regardless of the size of the disk. In contrast, we find that five out of six sources are clearly resolved at 100 microns. Three sources were also observed at 50 microns and at least two were resolved. Consequently the far-infrared emission must arise in another component, most plausibly a circumstellar envelope. This suggests that the group I sources may be less distinct from the group II sources than previously suggested. Since the presence of an envelope can affect both the actual temperature distribution in a disk and the temperature distribution derived from modeling the emission, more consistent models, including both disks and envelopes, are needed for these sources.

Di Francesco, James↗

NASA NTRS1972

Surface roughness effects on equilibrium temperature.

An analysis is presented for evaluation of equilibrium temperature distribution on radiatively adiabatic, adjoint planes which are uniformly irradiated by a collimated solar flux. The analysis employs a semigrey spectral model. Radiation properties for surface emitted radiation are obtained from the expressions of electromagnetic theory for smooth surfaces. Rough surface properties for solar radiation are given by the Beckmann bidirectional reflectance model. Numerical solutions to the governing equations yield equilibrium temperature distributions for a range of the influencing parameters. Surface roughness has little influence on equilibrium temperature for materials with high values for solar absorptance. However, for low or intermediate values of solar absorptance, roughness effects on the spatial distribution of reflected solar radiation can significantly alter equilibrium temperature particularly at surface elements where radiant interaction is small.

Houchens, A. F.↗

NASA NTRS1982

Topoclimatological survey of Switzerland

The application of Heat Capacity Mapping Mission data to subsynoptic climate analysis of Switzerland was examined. The data included the surface temperature distributions of urban heat islands and the Swiss Alps. Analog and digital data evaluation procedures are described as well as the ground truth acquisition and comparison program. The dependence of the temperature distributions on topography and surface coverage types is assessed. The results indicate that air temperature inversion zones are detectable.

Winiger, M.↗

DOE OSTI2019

Impact of Control Blade Insertion on the Deformation Behavior of SiC-SiC Channel Boxes in Boiling Water Reactors

This report describes the analysis of distortion of a Silicon carbide fiber-reinforced silicon carbide matrix (SiC-SiC) composite channel box under in-reactor conditions of a boiling water reactor (BWR). The BWR core has significant gradients in the fast neutron flux across the channel box due to the presence of water rods within the fuel assemblies, and these gradients increase further with the insertion of control blades. As a result of temperature and neutron flux dependent irradiation induced swelling of SiC, the SiC-SiC composite channel box can undergo significant distortion. In this work, we evaluate the SiC-SiC channel box distortion for three different control blade positions. This analysis is based on the neutron flux and temperature distributions in the BWR core calculated using the neutronics code MPACT and thermalhydraulics code CTF. This calculation is coupled through temperature feedback. Subsequently, we have performed structural analysis based on the calculated neutron flux and temperature distributions, to determine the deformation and stress development in the channel box. The structural analysis was performed using the fuel performance modeling code BISON and the commercial finite element analysis software Abaqus. The results indicate that the channel box will undergo time dependent lateral bowing for all the control blade positions in the assembly. The bowing behavior is dominated by the swelling of SiC-SiC material under non-uniform neutron flux, and changes with variation in the control blade position. The lateral bending will cause a temporary interference between the channel box and the control blade. The developed stresses exceed the proportional limit stress of the material, which may cause matrix microcracking in the channel box. However, the stresses remain below the ultimate tensile strength of the material, and therefore, development of a full, through thickness crack in the channel box is not expected.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1981

The diffuse extreme-ultraviolet background - Constraints on hot coronal plasma

The Apollo-Soyuz data and data reported by Cash et al. (1976) have been reanalyzed in terms of both isothermal models and temperature distribution models. In the latter case, a power-law form is assumed for the relation between emission measure and temperature. A new upper limit on diffuse flux in the 20-73 eV band derived from Apollo-Soyuz observations made in the earth's shadow has been incorporated in the calculation. In the considered investigation the results of the new analysis are presented and the implications for the physical properties of the hot component of the interstellar medium are discussed. The analysis of the Berkeley extreme ultraviolet (EUV) diffuse background measurements using either isothermal or power law temperature distribution models for the emitting plasma indicates excellent qualitative agreement with hard X-ray data that suggest the sun to be immersed in a hot plasma that pervades most of space out to approximately 100 pc.

Paresce, F.↗

NASA NTRS1989

Some aspects of transient cooling of a radiating rectangular medium

The emission from a gray radiating medium is analyzed for transient cooling in surroundings at a low temperature. The medium is rectangular with no variations in the direction normal to the cross section. The integral equation for the transient temperature distribution is solved numerically using a two-dimensional Gaussian integration subroutine. The emissive ability for a rectangle at uniform temperature is compared with that for transient cooling where the temperature distribution of the region has reached a fully developed shape, as shown by a separation of variables solution. The two solutions provide the upper and lower bounds for the emittance of a rectangle during transient cooling. The emittances for various aspect ratios are presented as a function of the mean length of the rectangle and are compared with results for a plane layer and a cylinder.

Siegel, Robert↗

NASA NTRS1998

Rotor Blade Pressure Measurement in a Rotating Machinery Using Pressure and Temperature Sensitive Paints

Pressure and temperature sensitive paints have been utilized for the measurement of blade surface pressure and temperature distributions in a high speed axial compressor and an Allied Signal F109 gas turbine engine. Alternate blades were painted with temperature sensitive paints and then pressure sensitive paint. This combination allows temperature distributions to be accounted for when determining the blade suction surface pressure distribution. Measurements were taken and pressure maps on the suction surface of a blade were obtained over a range of rotational speeds. Pressure maps of the suction surface show-strong shock waves at the higher speeds.

Torgerson, S.↗

NASA NTRS1977

Heat transfer in cooled guide vanes

A numerical study to determine the temperature distribution in the guide vanes of a radial inflow turbine is presented. A computer program has been developed to calculate the temperature distribution when the vanes are cooled internally using a combination of impingement and film cooling techniques. The study is based on the use of the finite difference method in a two dimensional heat conduction problem. The results are then compared to determine the best cooling configuration for a certain coolant to primary mass flow ratio.

Tabakoff, W.↗

NASA NTRS1987

Transient radiative cooling of a droplet-filled layer

A proposed lightweight radiator system for waste heat dissipation in space would eject streams of coolant in the form of small, hot liquid droplets. The droplets would lose radiative energy by direct exposure to the very low-temperature environment of space, and would then be collected for reuse. The cooling behavior of a layer composed of many small droplets was studied by numerical solution of the radiative integral equations. Since there is mutual interference for radiative energy dissipation, an array droplet will cool more slowly than if each drop is exposed individually. Since liquid metal droplets may be used, the study includes results for conditions with high scattering. For optically thin regions, especially with high scattering, the temperature distribution is sufficiently uniform that the cooling can be computed using the approximation of a constant layer emittance. For optically thick layers starting at uniform temperature, the temperature distributions become nonuniform with time. It was found that the cooling process goes through a starting transient; a constant emittance condition is then achieved where the emittance is lower than that for a layer at uniform temperature.

Siegel, R.↗

NASA NTRS2011

Seasonal Changes in Titan's Surface Temperatures

Seasonal changes in Titan's surface brightness temperatures have been observed by Cassini in the thermal infrared. The Composite Infrared Spectrometer (CIRS) measured surface radiances at 19 micron in two time periods: one in late northern winter (Ls = 335d eg) and another centered on northern spring equinox (Ls = 0 deg). In both periods we constructed pole-to-pole maps of zonally averaged brightness temperatures corrected for effects of the atmosphere. Between late northern winter and northern spring equinox a shift occurred in the temperature distribution, characterized by a warming of approximately 0.5 K in the north and a cooling by about the same amount in the south. At equinox the polar surface temperatures were both near 91 K and the equator was 93.4 K. We measured a seasonal lag of delta Ls approximately 9 in the meridional surface temperature distribution, consistent with the post-equinox results of Voyager 1 as well as with predictions from general circulation modeling. A slightly elevated temperature is observed at 65 deg S in the relatively cloud-free zone between the mid-latitude and southern cloud regions.

Jennins, Donald E.↗

NASA NTRS1993

Multi-dimensional modeling of pressurization and expulsion of multi-phase hydrogen propellant

A multidimensional computational model of the pressurization process in a slush hydrogen propellant storage tank was developed and its accuracy evaluated by comparison to experimental data measured for a 5 ft diameter spherical tank. The fluid mechanic, thermodynamic, and heat transfer processes within the ullage are represented by a finite-volume model. the heat and mass fluxes at the ullage boundary were computed in auxiliary analyses and specified as input to the finite-volume model. the model was shown to be in reasonable agreement with the experimental data. A parameter study was undertaken to examine the dependence of the pressurization process on initial ullage temperature distribution and pressurant mass flow rate. It is shown that for a given heat flux rate at the ullage boundary, the pressurization process is nearly independent of initial temperature distribution. The mass flow rate study revealed decreasing pressurant mass requirements with increasing pressurant mass flow rate. Further, significant differences were identified between the ullage temperature and velocity fields predicted for pressurization of slush and those predicted for pressurization of liquid hydrogen. A simplified model of the pressurization process was constructed in search of a dimensionless characterization of the pressurization process. It is shown that the relationship derived from this simplified model collapses all of the pressure history data generated during this study into a single curve.

Source record↗

NASA NTRS1987

Radiative cooling of a layer with nonuniform velocity - A separable solution

Analyzed here is the cooling of a flowing plane layer filled with hot particles or liquid droplets that emit, absorb, and scatter radiation. The velocity distribution is nonuniform across the layer and the specified shape of this distribution affects the layer temperature distribution and emittance. The velocity distribution determined is one that will cause the layer to cool at a uniform temperature. Thus, if the layer initially has a uniform temperature, it will retain the same emittance throughout its length. A separable solution is found that applies in a 'fully developed' region following an initial cooling length. In this developed region, the solution shows that there is a constant emittance based on the local heat loss and local bulk mean layer temperature. This emittance is a function of the velocity distribution, optical thickness, and scattering albedo.

Siegel, Robert↗