SEARCH · Search NASA

Results for “EDGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1988

A comparison of experimental and calculated thin-shell leading-edge buckling due to thermal stresses

High-temperature thin-shell leading-edge buckling test data are analyzed using NASA structural analysis (NASTRAN) as a finite element tool for predicting thermal buckling characteristics. Buckling points are predicted for several combinations of edge boundary conditions. The problem of relating the appropriate plate area to the edge stress distribution and the stress gradient is addressed in terms of analysis assumptions. Local plasticity was found to occur on the specimen analyzed, and this tended to simplify the basic problem since it effectively equalized the stress gradient from loaded edge to loaded edge. The initial loading was found to be difficult to select for the buckling analysis because of the transient nature of thermal stress. Multiple initial model loadings are likely required for complicated thermal stress time histories before a pertinent finite element buckling analysis can be achieved. The basic mode shapes determined from experimentation were correctly identified from computation.

Jenkins, Jerald M.↗

NASA NTRS1988

The effect of acoustic forcing on trailing edge separation and near wake development of an airfoil

An experimental study was conducted to investigate the effect of acoustic forcing on flow fields near the trailing edge of a symmetric airfoil at zero angle of attack. At low chord Reynolds numbers, the boundary layers separate from the surfaces in the rear part of the airfoil and create recirculation regions near the trailing edge. It is shown that with the introduction of acoustic forcing through a slot in the vicinity of the separation point, periodic large-scale structures are generated in the trailing edge region. Significant reduction of trailing edge separation is achieved. It is also found that the most effective forcing frequency to control trailing edge separation is the wake vortex shedding frequency. As a result of forcing, applied only on the upper surface, the upper boundary layer is accelerated and the flow over the lower surface decelerated. Consequently, an asymmetric wake is formed. The results presented indicate that the development of the near wake varies with forcing conditions.

Huang, L. S.↗

NASA NTRS1989

A method to design blended rolled edges for compact range reflectors

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameter is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Gupta, Inder J.↗

NASA NTRS1989

Numerical study of the effect of tangential leading edge blowing on delta wing vortical flow

A numerical simulation of tangential blowing along the leading edge of a delta wing is analyzed as a means of controlling the position and strength of the leading-edge vortices. The computation is done by numerical solutions of the three-dimensional thin-layer Navier-Stokes equations. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of tangential leading-edge blowing at low to moderate angles of attack tends to reduce the pressure peaks associated with leading-edge vortices and to increase the suction peak around the leading edge, such that the integrated value of the surface pressure remains about the same.

Yeh, David T.↗

NASA NTRS1990

Time-accurate Navier-Stokes computations of classical two-dimensional edge tone flow fields

Time-accurate Navier-Stokes computations were performed to study a Class II (acoustic) whistle, the edge tone, and gain knowledge of the vortex-acoustic coupling mechanisms driving production of these tones. Results were obtained by solving the full Navier-Stokes equations for laminar compressible air flow of a two-dimensional jet issuing from a slit interacting with a wedge. Cases considered were determined by varying the distance from the slit to the edge. Flow speed was kept constant at 1750 cm/sec as was the slit thickness of 0.1 cm, corresponding to conditions in the experiments of Brown. Excellent agreement was obtained in all four edge tone stage cases between the present computational results and the experimentally obtained results of Brown. Specific edge tone generated phenomena and further confirmation of certain theories concerning these phenomena were brought to light in this analytical simulation of edge tones.

Liu, B. L.↗

NASA NTRS1989

Real time optical edge enhancement using a Hughes liquid crystal light valve

The discovery of an edge enhancement effect in using a Hughes CdS liquid crystal light valve (LCLV) is reported. An edge-enhanced version of the input writing image can be directly obtained by operating the LCLV at a lower bias frequency and bias voltage. Experimental conditions in which this edge enhancement effect can be optimized are described. Experimental results show that the SNR of the readout image using this technique is superior to that obtained using high-pass filtering. The repeatability of this effect is confirmed by obtaining an edge enhancement result using two different Hughes LCLVs. The applicability of this effect to improve discrimination capability in optical pattern recognition is addressed. The results show that the Hughes LCLV can be used in both continuous tone and edge-enhancing modes by simply adjusting its bias conditions.

Chao, Tien-Hsin↗

NASA NTRS1990

A method to design blended rolled edges for compact range reflectors

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameters is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Gupta, Inder J.↗

NASA NTRS1990

A computational study of incipient leading-edge separation on a 65-deg delta wing at M = 1.60

A computational study on a 65-deg delta wing at a freestream Mach number of 1.60 has been conducted by obtaining conical Reynolds-averaged Navier-Stokes solutions on a parametric series of geometries which varied in leading-edge radius and/or circular-arc camber. The computational results showed that increasing leading-edge radius or camber can delay the onset of leading-edge separation on the leeside of a delta wing at a specific angle of attack. Reynolds number was varied from 1 x 10 to the 6th to 5 x 10 to the 6th for a turbulent boundary-layer and was shown to have a minor effect on the effectiveness of leading-edge radius and/or camber in delaying the onset of leading-edge separation. Both laminar and turbulent boundary-layer models were investigated at a Reynolds number of 1 x 10 to the 6th, and the predicted flow pattern was found to change from attached flow for the turbulent boundary-layer model to separated flow for the laminar boundary-layer model. Based upon these results, three wind-tunnel models have been designed to be tested in the Langley Unitary Plan Wind Tunnel.

Mcmillin, S. Naomi↗

NASA NTRS1991

Liquid-Crystal Light Valve Enhances Edges In Images

Experiments show liquid-crystal light valve (LCLV) exhibits operating mode in which it enhances edges in images projected on it. Operates in edge-enhancing mode (or in combination of edge-enhancing and normal modes) by suitably adjusting bias voltage and frequency. Enhancement of edges one of most important preprocessing steps in optical pattern-recognition systems. Incorporated into image-processing system to enhance edges without introducing excessive optical noise.

Chao, Tien-Hsin↗

NASA NTRS1991

Near-edge study of gold-substituted YBa2Cu3O(7-delta)

The valence of Cu and Au in YBa2Au0.3Cu2.7O7-delta was investigated using x-ray absorption near edge structure (XANES). X-ray and neutron diffraction studies indicate that Au goes on the Cu(1) site and Cu K-edge XANES shows that this has little effect on the oxidation state of the remaining copper. The Au L3 edge develops a white line feature whose position lies between that of trivalent gold oxide and monovalent potassium gold cyanide, and whose height relative to the edge step is smaller than in the two reference compounds. The appearance of the Au L3 edge suggests that fewer Au 3d states are involved in forming the Au-O bond in YBa2Au0.3Cu2.7O7-delta than in trivalent gold oxide.

Ruckman, Mark W.↗

NASA NTRS1991

Planform curvature effects on flutter characteristics of a wing with 56 deg leading-edge sweep and panel aspect ratio of 1.14

An experimental and analytical investigation was initiated to determine the effects of planform curvature (curving the leading and trailing edges of a wing in the X-Y plane) on the transonic flutter characteristics of a series of three moderately swept wing models. Experimental flutter results were obtained in the Langley Transonic Dynamics Tunnel for Mach numbers from 0.60-1.00, with air as the test medium. The models were semispan cantilevered wings with a 3 percent biconvex airfoil and a panel aspect ratio of 1.14. The baseline model had straight leading and trailing edges (i.e., no planform curvature). The radii of curvature of the leading edges for these two models were 200 and 80 inches. The radii of curvature of the leading edges of the other two models were determined so that the root and tip chords were identical for all three models. Experimental results showed that flutter-speed index and flutter frequency ratio increased as planform curvature increase (radius of curvature of the leading edge was decreased) over the test range of Mach numbers. Analytical flutter results were calculated with a subsonic flutter-prediction program, and they agreed well with the experimental results.

Keller, Donald F.↗

NASA NTRS1992

Blade-mounted trailing edge flap control for BVI noise reduction

Numerical procedures based on the 2-D and 3-D full potential equations and the 2-D Navier-Stokes equations were developed to study the effects of leading and trailing edge flap motions on the aerodynamics of parallel airfoil-vortex interactions and on the aerodynamics and acoustics of the more general self-generated rotor blade vortex interactions (BVI). For subcritical interactions, the 2-D results indicate that the trailing edge flap can be used to alleviate the impulsive loads experienced by the airfoil. For supercritical interactions, the results show the necessity of using a leading edge flap, rather than a trailing edge flap, to alleviate the interaction. Results for various time dependent flap motions and their effect on the predicted temporal sectional loads, differential pressures, and the free vortex trajectories are presented. For the OLS model rotor, contours of a BVI noise metric were used to quantify the effects of the trailing edge flap on the size and directivity of the high/low intensity noise region(s). Average reductions in the BVI noise levels on the order of 5 dB with moderate power penalties on the order of 18 pct. for a four bladed rotor and 58 pct. for a two bladed rotor were obtained.

Hassan, A. A.↗

NASA NTRS1992

A simplified method for thermal analysis of a cowl leading edge subject to intense local shock-wave-interference heating

Type IV shock wave interference heating on a blunt body causes extremely intense heating over a very localized region of the body. An analytical solution is presented to a heat transfer problem that approximates the shock wave interference heating of an engine cowl leading edge of the National Aero-Space Plane. The problem uses a simplified geometry to represent the leading edge. An analytical solution is developed that provides a means for approximating maximum temperature differences between the outer and inner surface temperatures of the leading edge. The solution is computationally efficient and, as a result, is well suited for conceptual and preliminary design or trade studies. Transient and steady state analyses are conducted, and results obtained from the analytical solution are compared with results of 2-D thermal finite element analyses over a wide range of design parameters. Isotropic materials as well as laminated composite materials are studied. Results of parametric studies are presented to indicate the effects of the thickness of the cowl leading edge and the width of the region heated by the shock wave interference on the thermal response of the leading edge.

Mcgowan, David M.↗

NASA NTRS1992

Laboratory Velocimeter Measurements Using the Edge Technique

We have developed a simple but powerful measurement methodology using the edge technique to measure the Doppler shift of backscatter laser radiation. With this method, instantaneous velocity information, including wind measurements, can be obtained with sub-meter-per-second accuracy and with high range resolution using a pulsed lidar system. This paper describes laboratory experiments that demonstrate the basic principles of the edge technique. These experiments demonstrate the sensitivity of the technique and the high velocity accuracy which can be obtained. In addition, many of the characteristics which make the edge technique a powerful method for use in lidar wind application were verified. These include the insensitivity of the measurement to laser and/or edge filter frequency jitter and drift, and the ability to make Doppler shift measurements which are of the order of 100 times better than the spectral bandwidth of the measurement (the combined spectral width of the laser and edge filter).

Gentry, Bruce M.↗

NASA NTRS1991

Near-edge study of gold-substituted YBa2Cu3O(7-delta)

The valence of Cu and Au in YBa2Au0.3Cu2.7O7-delta was investigated using X-ray absorption near edge structure (XANES). X-ray and neutron diffraction studies indicate that Au goes on the Cu(1) site and Cu K-edge XANES shows that this has little effect on the oxidation state of the remaining copper. The Au L3 edge develops a white line feature whose position lies between that of trivalent gold oxide and monovalent potassium gold cyanide, and whose height relative to the edge step is smaller than in the two reference compounds. The appearance of the Au L3 edge suggests that fewer Au 3d states are involved in forming the Au-O bond in YBa2Au0.3Cu2.7O7-delta than in trivalent gold oxide.

Ruckman, Mark W.↗

NASA NTRS1992

Edge detection algorithm for SST images

An algorithm to detect fronts in satellite-derived sea surface temperature fields is presented. Although edge detection is the main focus, the problem of cloud detection is also addressed since unidentified clouds can lead to erroneous edge detection. The algorithm relies on a combination of methods and it operates at the picture, the window, and the local level. The resulting edge detection is not based on the absolute strength of the front, but on the relative strength depending on the context, thus, making the edge detection temperature-scale invariant. The performance of this algorithm is shown to be superior to that of simpler algorithms commonly used to locate edges in satellite-derived SST images. This evaluation was performed through a careful comparison between the location of the fronts obtained by applying the various methods to the SST images and the in situ measures of the Gulf Stream position.

Cayula, Jean-Francois↗

NASA NTRS1993

Reflectance calibrations of AXAF mirror samples at absorption edges using synchrotron radiation

We are developing a system to calibrate reflectances of witness coupons to the AXAF flight mirrors at the National Synchrotron Light Source over the 0.05-12 keV energy range. These witness coupons will be coated in the same process as the AXAF mirror elements. One of the key issues is the accurate determination of mirror efficiencies across the absorption edges of the mirror coating elements. We present a series of reflectance measurements with 2 eV resolution of a nickel-coated flat mirror in the region of the Ni L-II (870 eV) and L-III (853 eV) absorption edges. Scans of reflectance versus grazing angle at fixed energies in this region show distinct interference fringes at grazing angles larger than the critical angle which are extinguished as the photon energy is increased beyond the low point of the L-III edge, indicating total absorption of the evanescent wave within the Ni film. At 51 arc minutes grazing angle, measured reflectance decreases smoothly by 35 percent and then recovers in an 8 eV band at the L-III edge. We have also measured reflectances in the M absorption edge region for gold, platinum, and iridium coated mirrors. We derive optical parameters n and k specific to the film for comparison to the existing data tables.

Graessle, D. E.↗

NASA NTRS1994

Numerical simulation of the edge tone phenomenon

Time accurate Navier-Stokes computations were performed to study a class 2 (acoustic) whistle, the edge tone, and to gain knowledge of the vortex-acoustic coupling mechanisms driving production of these tones. Results were obtained by solving the full Navier-Stokes equations for laminar compressible air flow of a two dimensional jet issuing from a slit interacting with a wedge. Cases considered were determined by varying the distance from the slit to the wedge. Flow speed was kept constant at 1,750 cm/s as was the slit thickness of 0.1 cm, corresponding to conditions in the experiments of Brown. The analytical computations revealed edge tones to be present in four harmonic stages of jet flow instability over the wedge as the jet length was varied from 0.3 to 1.6 cm. Excellent agreement was obtained in all four edge tone stage cases between the present computational results and the experimentally obtained frequencies and flow visualization results of Brown. Specific edge tone generation phenomena and further confirmation of certain theories and empirical formulas concerning these phenomena were brought to light in this analytical simulation of edge tones.

Dougherty, N. S.↗