Search NASA⌕ Search

SEARCH · Search NASA

Results for “Elemental analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Finite element analysis of the effect of a non-planar solid-liquid interface on the lateral solute segregation during unidirectional solidification

The effect of solid-liquid interface shape on lateral solute segregation during steady-state unidirectional solidification of a binary mixture is calculated under the assumption of no convection in the liquid. A finite element technique is employed to compute the concentration field in the liquid and the lateral segregation in the solid with a curved boundary between the liquid and solid phases. The computational model is constructed assuming knowledge of the solid-liquid interface shape; no attempt is made to relate this shape to the thermal field. The influence of interface curvature on the lateral compositional variation is investigated over a range of system parameters including diffusivity, growth speed, distribution coefficient, and geometric factors of the system. In the limiting case of a slightly nonplanar interface, numerical results from the finite element technique are in good agreement with the analytical solutions of Coriell and Sekerka obtained by using linear theory. For the general case of highly non-planar interface shapes, the linear theory fails and the concentration field in the liquid as well as the lateral solute segregation in the solid can be calculated by using the finite element method.

Carlson, F. M.↗

Three-Dimensional Effects in the Plate Element Analysis of Stitched Textile Composites

Three-dimensional effects related to the analysis of stitched textile composites are discussed. The method of calculation is based on the virtual crack closure technique (VCCT), and models that model the upper and lower surface of the delamination or debond with two-dimensional (2D) plate elements rather than three-dimensional (3D) solid elements. The major advantages of the plate element modeling technique are a smaller model size and simpler geometric modeling. Details of the modeling of the laminated plate and the stitching are discussed.

Glaessgen, E. H.↗

Finite Element Analysis on Spread for In-plane Roll-bending Process

The in-plane roll-bending process is a special wedge rolling with a configuration of two conical rolls which can form strips into open ring products. The spread of a ring is usually not considered in previous radius predicting models by Yang et al. and Xian et al. However, the spread increases to 10% for a ring with average reduction of 56%, and there is a discrepancy between the predicted radius and the experiment. Spread analysis/calculation has become an urgent problem in radius prediction and precision control of unequal deformation in this process. A finite element (FE) model considering spread effect is established and evaluated by experiments. A comparison between the predicted results with/without considering spread by FE analysis and experiments is carried out. The result shows that the predicted results considering spread are much closer to the experiments than those without considering spread effect. Based on the FE simulation, the spread characteristics of the ring with two types of cross section (including partly and entirely compressed cross section) are investigated. It is found that, there exist three spread regions, including outer positive region, middle negative region and inner positive region for the partly compressed ring; and there are outer positive region and inner negative region for the entirely compressed ring. The spread mostly happens at the outer positive region for both types of ring. The effects of process parameters, such as wedge angle, bite location, friction coefficient and rotational speed of roll, on spread for three aluminum alloys, 3A21O, 5A02O and 2A12T4, are investigated. The results indicate that the spread decreases with an increase in wedge angle, whereas increases with the growth of bite location; the spread remains stable with increasing friction coefficient and fluctuates within 3%-8% with a rise in rotational speed of roll. The spread of the partly compressed ring is less than 6%; large spread (larger than 6%) occurs when the ring is entirely compressed; the spread may reach a maximum value of 18.8% for material 5A02O.

36 MATERIALS SCIENCE↗

Multi-Fidelity Scheme for Accelerating 4D Finite Element Analysis for Mircoreactors

Next-generation microreactors are currently being designed to be operated terrestrial and extraterrestrial for remote surface power production. These systems will provide an alternative source of carbon-free energy that is versatile and can be utilized for various applications. These applications of microreactors have prompted the usage of high-fidelity unstructured finite element (FE) based approaches to provide time-dependent solutions for multiple physics fields. Computing these high-fidelity (4-D) solutions for multiple design iterations, physics fields, and transient events requires an immense computational cost. These high-fidelity solutions are computational expensive and the cost can be reduced through the implementation of less accurate low-fidelity solutions. Unlike the current fleet of commercial nuclear reactors, these next-gen systems present challenges due to the material and physical limitations required. Due to these constraints, the brute force technique of parameterizing important system characteristics determines whether a design meets the project objective. A system such as a nuclear reactor could have thousands of design parameters that affect system performance. In order to analyze the entire parameter space of such a complex system would require millions of CPU hours and countless design iterations. This costly approach is not practical due to regulatory and budget limitations. In this proposal, an approach that utilizes hybrid high-fidelity and low-fidelity FE models to reduce the computational cost of evaluating these applications in 4-D will be presented. The accuracy of the high-fidelity model and the computational efficiency of the low-fidelity model are taken advantage of to produce a solution that closely resembles the full order high-fidelity solution. By utilizing an unconverged coarse FE mesh, operation limits such as temperature, structural loading, etc., can be evaluated in an accelerated fashion and then can be spatially interpolated onto a finer mesh. The resulting error arising from the coarse mesh can be mitigated with a discrepancy function that actively quantifies and corrects the error in the coarse solution. This discrepancy function can be periodically updated with high-fidelity calculations across the temporal domain thus requiring less iterations on the fine mesh. As a result, the computational cost can be reduced for the evaluation and design iteration of microreactors. The proposal for this research contains three sections: Section 2 provides a literature review, Section 3 outlines the methodology for the proposed multi-fidelity scheme, and Section 4 displays preliminary results of the proposed research.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Probabilistic Fatigue Damage Prognosis Using a Surrogate Model Trained Via 3D Finite Element Analysis

Utilizing inverse uncertainty quantification techniques, structural health monitoring can be integrated with damage progression models to form probabilistic predictions of a structure's remaining useful life. However, damage evolution in realistic structures is physically complex. Accurately representing this behavior requires high-fidelity models which are typically computationally prohibitive. In the present work, a high-fidelity finite element model is represented by a surrogate model, reducing computation times. The new approach is used with damage diagnosis data to form a probabilistic prediction of remaining useful life for a test specimen under mixed-mode conditions.

Leser, Patrick E.↗

Finite Element Analysis of the Random Response Suppression of Composite Panels at Elevated Temperatures using Shape Memory Alloy Fibers

A feasibility study on the use of shape memory alloys (SMA) for suppression of the random response of composite panels due to acoustic loads at elevated temperatures is presented. The constitutive relations for a composite lamina with embedded SMA fibers are developed. The finite element governing equations and the solution procedures for a composite plate subjected to combined acoustic and thermal loads are presented. Solutions include: 1) Critical buckling temperature; 2) Flat panel random response; 3) Thermal postbuckling deflection; 4) Random response of a thermally buckled panel. The preliminary results demonstrate that the SMA fibers can completely eliminate the thermal postbuckling deflection and significantly reduce the random response at elevated temperatures.

Turner, Travis L.↗

Source Attribution of Cyanides using Anionic Impurity Profiling, Stable Isotope Ratios, Trace Elemental Analysis and Chemometrics

Chemical attribution signatures (CAS) for chemical threat agents (CTAs) are being investigated to provide an evidentiary link between CTAs and specific sources to support criminal investigations and prosecutions. In a previous study, anionic impurity profiles developed using high performance ion chromatography (HPIC) were demonstrated as CAS for matching samples from eight potassium cyanide (KCN) stocks to their reported countries of origin. Herein, a larger number of solid KCN stocks (n = 13) and, for the first time, solid sodium cyanide (NaCN) stocks (n = 15) were examined to determine what additional sourcing information can be obtained through anion, carbon stable isotope, and elemental analyses of cyanide stocks by HPIC, isotope ratio mass spectrometry (IRMS), and inductively coupled plasma optical emission spectroscopy (ICP-OES), respectively. The HPIC anion data was evaluated using the variable selection methods of Fisher-ratio (F-ratio), interval partial least squares (iPLS), and genetic algorithm-based partial least squares (GAPLS) and the classification methods of partial least squares discriminate analysis (PLSDA), K nearest neighbors (KNN), and support vector machines discriminate analysis (SVMDA). In summary, hierarchical cluster analysis (HCA) of anion impurity profiles from multiple cyanide stocks from six reported country of origins resulted in cyanide samples clustering into three groups: Czech Republic, Germany, and United States, independent of the associated alkali metal (K or Na). The three country groups were independently corroborated by HCA of cyanide elemental profiles and corresponded to countries with known solid cyanide factories. Both the anion and elemental CAS are believed to originate from the aqueous alkali hydroxides used in cyanide manufacture. Carbon stable isotope measurements resulted in two clusters: Germany and United States (the single Czech stock grouped with United States stocks). The carbon isotope CAS is believed to originate from the carbon source and process used to make the HCN utilized in cyanide synthesis. Classification errors for two validation studies using anion impurity profiles collected over five years on different instruments were as low as zero for KNN and SVMDA, demonstrating the excellent reliability (so far) of using anion impurities for matching a cyanide sample to its country of manufacture (i.e., factory). Variable selection reduced errors for those classification methods having errors greater than zero with iPLS-forward selection, and F-ratio typically providing the lowest errors. Finally, using anion profiles to match cyanides to a specific stock or stock group resulted in cross-validation errors ranging from zero to 5.3%.

chemical forensics↗

Hybrid-finite-element analysis of some nonlinear and 3-dimensional problems of engineering fracture mechanics

In this paper, efficient numerical methods for the analysis of crack-closure effects on fatigue-crack-growth-rates, in plane stress situations, and for the solution of stress-intensity factors for arbitrary shaped surface flaws in pressure vessels, are presented. For the former problem, an elastic-plastic finite element procedure valid for the case of finite deformation gradients is developed and crack growth is simulated by the translation of near-crack-tip elements with embedded plastic singularities. For the latter problem, an embedded-elastic-singularity hybrid finite element method, which leads to a direct evaluation of K-factors, is employed.

Atluri, S. N.↗

Finite element analysis of the Arquin-designed CMU wall under a dynamic (blast) load.

The Arquin Corporation designed a CMU (concrete masonry unit) wall construction and reinforcement technique that includes steel wire and polymer spacers that is intended to facilitate a faster and stronger wall construction. Since the construction method for an Arquin-designed wall is different from current wall construction practices, finite element computer analyses were performed to estimate the ability of the wall to withstand a hypothetical dynamic load, similar to that of a blast from a nearby explosion. The response of the Arquin wall was compared to the response of an idealized standard masonry wall exposed to the same dynamic load. Results from the simulations show that the Arquin wall deformed less than the idealized standard wall under such loading conditions. As part of a different effort, Sandia National Laboratories also looked at the relative static response of the Arquin wall, results that are summarized in a separate SAND Report.

36 MATERIALS SCIENCE↗

Finite element analysis of periodic transonic flow problems

Flow about an oscillating thin airfoil in a transonic stream was considered. It was assumed that the flow field can be decomposed into a mean flow plus a periodic perturbation. On the surface of the airfoil the usual Neumman conditions are imposed. Two computer programs were written, both using linear basis functions over triangles for the finite element space. The first program uses a banded Gaussian elimination solver to solve the matrix problem, while the second uses an iterative technique, namely SOR. The only results obtained are for an oscillating flat plate.

Fix, G. J.↗

On the Representation of Through-The-Thickness Reinforcements in Finite Element Analysis of Stitched, Blade Stiffened Panels

Modern aircraft employ laminated composites for their tailorable in-plane properties, high specific strengths, and high specific stiffnesses. However, laminated composites exhibit relatively poor interlaminar properties without through-the-thickness reinforcements. Quantifying the necessary amount of through-the-thickness reinforcements is necessary to reduce cost and meet damage tolerance certification requirements. In this study, a discrete superposed cohesive element (DSCE) approach is applied to represent the mixed-mode delamination behavior of stitched stiffened panels subjected to seven-point bending. This approach is compared to a one-dimensional embedded spring element (ESE) method. The DSCE approach uses two superposed bilinear traction-separation laws to obtain a representative load-displacement response determined from interlaminar tensile and shear tests. Additionally, several stitch configurations (unstitched, stitched, and overstitched) are evaluated in terms of their load-displacement response and crack-arrestment capability. Results indicate that the DSCE and ESE approaches show good agreement with respect to the predicted load-displacement response, but the ESE method tends to overpredict the crack growth behavior by approximately 13%. Stitches were not observed to fail during skin-stringer separation. Using an overstitched laminate with stitches near the flange edge provides the greatest crack-arrestment capability. Furthermore, the skin retains 92% of its stiffness after skin-stringer separation occurs.

composites↗

On the Representation of Through-The-Thickness Reinforcements in Finite Element Analysis of Stitched, Blade Stiffened Panels

Modern aircraft employ laminated composites for their tailorable in-plane properties, high specific strengths, and high specific stiffnesses. However, laminated composites exhibit relatively poor interlaminar properties without through-the-thickness reinforcements. Quantifying the necessary amount of through-the-thickness reinforcements is necessary to reduce cost and meet damage tolerance certification requirements. In this study, a discrete superposed cohesive element (DSCE) approach is applied to represent the mixed-mode delamination behavior of stitched stiffened panels subjected to seven-point bending. This approach is compared to a one-dimensional embedded spring element (ESE) method. The DSCE approach uses two superposed bilinear traction-separation laws to obtain a representative load-displacement response determined from interlaminar tensile and shear tests. Additionally, several stitch configurations (unstitched, stitched, and overstitched) are evaluated in terms of their load-displacement response and crack-arrestment capability. Results indicate that the DSCE and ESE approaches show good agreement with respect to the predicted load-displacement response, but the ESE method tends to overpredict the crack growth behavior by approximately 13%. Stitches were not observed to fail during skin-stringer separation. Using an overstitched laminate with stitches near the flange edge provides the greatest crack-arrestment capability. Furthermore, the skin retains 92% of its stiffness after skin-stringer separation occurs.

composites↗

Finite element analysis of an extended end-plate connection using the T-stub approach

Beam-to-column end-plate bolted connections are usually used as moment-resistant connections in steel framed structures. For this joint type, the deformability is governed by the deformation capacity of the column flange and end-plate under tension and elongation of the bolts. All these elements around the beam tension flange form the tension region of the joint, which can be modeled by means of equivalent T-stubs. In this paper a beam-to-column end-plate bolted connection is substituted with a T-stub of appropriate effective length and it is analyzed using the commercially available finite element software ABAQUS. The performance of the model is validated by comparing the behavior of the T-stub from the numerical simulation with the behavior of the connection as a whole. The moment-rotation curve of the T-stub obtained from the numerical simulation is compared with the behavior of the whole extended end-plate connection, obtained by numerical simulation, experimental tests and analytical approach.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Finite element analysis of thermal barrier coatings

The near-term objective is to develop an understanding of the states of stresses and strains in a Zirconia-yttria thermal barrier coating (TBC) experiencing a given temperature drop. Results so obtained are expected to facilitate experimental work. In order to gain realistic insights into the distribution of stresses and strains in a complex TBC, the finite element approach was selected to model a cylindrical TBC specimen. Experimental evidence reported in the literature indicated the presence of rough interface between the ceramic coat and bond coat. Oxidation of the bond coat at ceramic-bond interface was observed, as was a small amount of cracking in the ceramics near the ceramic-bond interface. To account for these complex features, a plane-strain finite element computer program known as TBCOC was developed, taking advantage of a generic computer code known as MARC. This generic code was made available through the use of a supercomputer (Cray 1). The TBCOC model contains 1316 nodal points and 2140 finite elements. It is capable of a uniform isothermal loading. Results of a sample computer run are presented.

Chang, G. C.↗

Compatibility conditions of structural mechanics for finite element analysis

The equilibrium equations and the compatibility conditions are fundamental to the analyses of structures. However, anyone who undertakes even a cursory generic study of the compatibility conditions can discover, with little effort, that historically this facet of structural mechanics had not been adequately researched by the profession. Now the compatibility conditions (CC's) have been researched and are understood to a great extent. For finite element discretizations, the CC's are banded and can be divided into three distinct categories: (1) the interface CC's; (2) the cluster or field CC's; and (3) the external CC's. The generation of CC's requires the separating of a local region, then writing the deformation displacement relation (ddr) for the region, and finally, the eliminating of the displacements from the ddr. The procedure to generate all three types of CC's is presented and illustrated through examples of finite element models. The uniqueness of the CC's thus generated is shown.

Patnaik, Surya N.↗

Compatibility conditions of structural mechanics for finite element analysis

The equilibrium equations and the compatibility conditions are fundamental to the analyses of structures. However, anyone who undertakes even a cursory generic study of the compatibility conditions can discover, with little effort, that historically this facet of structural mechanics had not been adequately researched by the profession. Now the compatibility conditions (CC's) have been researched and are understood to a great extent. For finite element discretizations, the CC's are banded and can be divided into three distinct categories: (1) the interface CC's; (2) the cluster or field CC's; and (3) the external CC's. The generation of CC's requires the separating of a local region, then writing the deformation displacement relation (ddr) for the region, and finally, the eliminating of the displacements from the ddr. The procedure to generate all three types of CC's is presented and illustrated through examples of finite element models. The uniqueness of the CC's thus generated is shown.

Patnaik, S. N.↗

Integrated force method - Compatibility conditions of structural mechanics for finite element analysis

The equilibrium equations and the compatibility conditions are fundamental to the analyses of structures. However, anyone who undertakes even a cursory generic study of the compatibility conditions can discover, with little effort, that historically this facet of structural mechanics had not been adequately researched by the profession. Now the compatibility conditions (CC's) have been researched and are understood to a great extent. For finite element discretizations, the CC's are banded and can be divided into three distinct categories: (1) the interface CC's, (2) the cluster or field CC's, and (3) the external CC's. The generation of CC's requires the separating of a local region, then writing the deformation displacement relation (ddr) for the region, and finally, the eliminating of the displacements from the ddr. The procedure to generate all three types of CC's is presented and illustrated through examples of finite element models. The uniqueness of the CC's thus generated is shown. The utilization of CC's has resulted in the novel integrated force method (IFM). The solution that is obtained by the IFM converges with a significantly fewer number of elements, compared to the stiffness and the hybrid methods.

Patnaik, Surya N.↗

A finite-element analysis for steady and oscillatory subsonic flow around complex configurations

The problem of potential subsonic flow around complex configurations is considered. The solution is given of an integral equation relating the values of the potential on the surface of the body to the values of the normal derivative, which is known from the boundary conditions. The surface of the body is divided into small (hyperboloidal quadrilateral) surface elements, which are described in terms of the Cartesian components of the four corner points. The values of the potential (and its normal derivative) within each element is assumed to be constant and equal to its value at the centroid of the element. The coefficients of the equation are given by source and doublet integrals over the surface elements. Closed form evaluations of the integrals are presented. The results obtained with the above formulation are compared with existing analytical and experimental results.

Chen, L. T.↗