Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flight control computer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Report of the workshop on Aviation Safety/Automation Program

As part of NASA's responsibility to encourage and facilitate active exchange of information and ideas among members of the aviation community, an Aviation Safety/Automation workshop was organized and sponsored by the Flight Management Division of NASA Langley Research Center. The one-day workshop was held on October 10, 1989, at the Sheraton Beach Inn and Conference Center in Virginia Beach, Virginia. Participants were invited from industry, government, and universities to discuss critical questions and issues concerning the rapid introduction and utilization of advanced computer-based technology into the flight deck and air traffic controller workstation environments. The workshop was attended by approximately 30 discipline experts, automation and human factors researchers, and research and development managers. The goal of the workshop was to address major issues identified by the NASA Aviation Safety/Automation Program. Here, the results of the workshop are documented. The ideas, thoughts, and concepts were developed by the workshop participants. The findings, however, have been synthesized into a final report primarily by the NASA researchers.

Morello, Samuel A.↗

Use of Convex supercomputers for flight simulation at NASA Langley

The use of the Convex Computer Corporation supercomputers for flight simulation is discussed focusing on a real-time input/output system for supporting the flight simulation. The flight simulation computing system is based on two single processor control data corporation CYBER 175 computers, coupled through extended memory. The Advanced Real-Time Simulation System for digital data distribution and signal conversion is a state-of-the-art, high-speed fiber-optic-based, ring network system which is based on the computer automated measurement and control technology.

Cleveland, Jeff I., II↗

Spatial interpretation of NASA's Marshall Space Flight Center Payload Operations Control Center using virtual reality technology

In its search for higher level computer interfaces and more realistic electronic simulations for measurement and spatial analysis in human factors design, NASA at MSFC is evaluating the functionality of virtual reality (VR) technology. Virtual reality simulation generates a three dimensional environment in which the participant appears to be enveloped. It is a type of interactive simulation in which humans are not only involved, but included. Virtual reality technology is still in the experimental phase, but it appears to be the next logical step after computer aided three-dimensional animation in transferring the viewer from a passive to an active role in experiencing and evaluating an environment. There is great potential for using this new technology when designing environments for more successful interaction, both with the environment and with another participant in a remote location. At the University of North Carolina, a VR simulation of a the planned Sitterson Hall, revealed a flaw in the building's design that had not been observed during examination of the more traditional building plan simulation methods on paper and on computer aided design (CAD) work station. The virtual environment enables multiple participants in remote locations to come together and interact with one another and with the environment. Each participant is capable of seeing herself and the other participants and of interacting with them within the simulated environment.

Lindsey, Patricia F.↗

A Summary of NASA Rotary Wing Research: Circa 2008–2018

The general public may not know that the first “A” in NASA stands for Aeronautics. If they do know, they will very likely be surprised that in addition to airplanes, the “A” includes research in helicopters, tiltrotors, and other vehicles adorned with rotors. There is, arguably, no subsonic air vehicle more difficult to accurately analyze than a vehicle with lift-producing rotors. No wonder that NASA has conducted rotary wing research since the days of the NACA and has partnered, since 1965, with the U.S. Army in order to overcome some of the most challenging obstacles to understanding the behavior of these vehicles. Since 2006, NASA rotary wing research has been performed under several different project names [Gorton et al., 2015]: Subsonic Rotary Wing (SRW) (2006–2012), Rotary Wing (RW) (2012–2014), and Revolutionary Vertical Lift Technology (RVLT) (2014–present). In 2009, the SRW Project published a report that assessed the status of NASA rotorcraft research; in particular, the predictive capability of NASA rotorcraft tools was addressed for a number of technical disciplines. A brief history of NASA rotorcraft research through 2009 was also provided [Yamauchi and Young, 2009]. Gorton et al. [2015] describes the system studies during 2009–2011 that informed the SRW/RW/RVLT project investment prioritization and organization. The authors also provided the status of research in the RW Project in engines, drive systems, aeromechanics, and impact dynamics as related to structural dynamics of vertical lift vehicles. Since 2009, the focus of research has shifted from large civil VTOL transports, to environmentally clean aircraft, to electrified VTOL aircraft for the urban air mobility (UAM) market. The changing focus of rotorcraft research has been a reflection of the evolving strategic direction of the NASA Aeronautics Research Mission Directorate (ARMD). By 2014, the project had been renamed the Revolutionary Vertical Lift Technology Project. In response to the 2014 NASA Strategic Plan, ARMD developed six Strategic Thrusts. Strategic Thrust 3B was defined as the “Ultra-Efficient Commercial Vehicles—Vertical Lift Aircraft.” Hochstetler et al. [2017] uses Thrust 3B as an example for developing metrics usable by ARMD to measure the effectiveness of each of the Strategic Thrusts. The authors provide near-, mid-, and long-term outcomes for Thrust 3B with corresponding benefits and capabilities. The importance of VTOL research, especially with the rapidly expanding UAM market, eventually resulted in a new Strategic Thrust (to begin in 2020): Thrust 4—Safe, Quiet, and Affordable Vertical Lift Air Vehicles. The underlying rotary wing analysis tools used by NASA are still applicable to traditional rotorcraft and have been expanded in capability to accommodate the growing number of VTOL configurations designed for UAM. The top-level goal of the RVLT Project remains unchanged since 2006: Develop and validate tools, technologies and concepts to overcome key barriers for vertical lift vehicles. In 2019, NASA rotary wing/VTOL research has never been more important for supporting new aircraft and advancements in technology. 2 A decade is a reasonable interval to pause and take stock of progress and accomplishments. In 10 years, digital technology has propelled progress in computational efficiency by orders of magnitude and expanded capabilities in measurement techniques. The purpose of this report is to provide a compilation of the NASA rotary wing research from ~2008 to ~2018. Brief summaries of publications from NASA, NASA-funded, and NASA-supported research are provided in 12 chapters: Acoustics, Aeromechanics, Computational Fluid Dynamics (External Flow), Experimental Methods, Flight Dynamics and Control, Drive Systems, Engines, Crashworthiness, Icing, Structures and Materials, Conceptual Design and System Analysis, and Mars Helicopter. We hope this report serves as a useful reference for future NASA vertical lift researchers.

Yamauchi, Gloria K.↗

A piloted simulation study of data link ATC message exchange

Data link Air Traffic Control (ATC) and Air Traffic Service (ATS) message and data exchange offers the potential benefits of increased flight safety and efficiency by reducing communication errors and allowing more information to be transferred between aircraft and ground facilities. Digital communication also presents an opportunity to relieve the overloading of ATC radio frequencies which hampers message exchange during peak traffic hours in many busy terminal areas. A piloted simulation study to develop pilot factor guidelines and assess potential flight crew benefits and liabilities from using data link ATC message exchange was completed. The data link ATC message exchange concept, implemented on an existing navigation computer Control Display Unit (CDU) required maintaining a voice radio telephone link with an appropriate ATC facility. Flight crew comments, scanning behavior, and measurements of time spent in ATC communication activities for data link ATC message exchange were compared to similar measures for simulated conventional voice radio operations. The results show crew preference for the quieter flight deck environment and a perception of lower communication workload.

Waller, Marvin C.↗

Evaluation of the efficiency and fault density of software generated by code generators

Flight computers and flight software are used for GN&C (guidance, navigation, and control), engine controllers, and avionics during missions. The software development requires the generation of a considerable amount of code. The engineers who generate the code make mistakes and the generation of a large body of code with high reliability requires considerable time. Computer-aided software engineering (CASE) tools are available which generates code automatically with inputs through graphical interfaces. These tools are referred to as code generators. In theory, code generators could write highly reliable code quickly and inexpensively. The various code generators offer different levels of reliability checking. Some check only the finished product while some allow checking of individual modules and combined sets of modules as well. Considering NASA's requirement for reliability, an in house manually generated code is needed. Furthermore, automatically generated code is reputed to be as efficient as the best manually generated code when executed. In house verification is warranted.

Schreur, Barbara↗

NASA's OCA Mirroring System: An Application of Multiagent Systems in Mission Control

Orbital Communications Adaptor (OCA) Flight Controllers, in NASA's International Space Station Mission Control Center, use different computer systems to uplink, downlink, mirror, archive, and deliver files to and from the International Space Station (ISS) in real time. The OCA Mirroring System (OCAMS) is a multiagent software system (MAS) that is operational in NASA's Mission Control Center. This paper presents OCAMS and its workings in an operational setting where flight controllers rely on the system 24x7. We also discuss the return on investment, based on a simulation baseline, six months of 24x7 operations at NASA Johnson Space Center in Houston, Texas, and a projection of future capabilities. This paper ends with a discussion of the value of MAS and future planned functionality and capabilities.

Sierhuis, Maarten↗

Automatic control of a primary electric thrust subsystem

A concept for automatic control of the thrust subsystem has been developed by JPL and participating NASA Centers. This paper reports on progress in implementing the concept at JPL. Control of the Thrust Subsystem (TSS) is performed by the spacecraft computer command subsystem, and telemetry data is extracted by the spacecraft flight data subsystem. The Data and Control Interface Unit, an element of the TSS, provides the interface with the individual elements of the TSS. The control philosophy and implementation guidelines are presented. Control requirements are listed, and the control mechanism, including the serial digital data intercommunication system, is outlined. The paper summarizes progress to Fall 1974.

Macie, T. W.↗

ANOPP/VMS HSCT ground contour system

This viewgraph shows the integration of the Visual Motion Simulator with ANOPP. ANOPP is an acronym for the Aircraft NOise Prediction Program. It is a computer code consisting of dedicated noise prediction modules for jet, propeller, and rotor powered aircraft along with flight support and noise propagation modules, all executed under the control of an executive system. The Visual Motion Simulator (VMS) is a ground based motion simulator with six degrees of freedom. The transport-type cockpit is equipped with conventional flight and engine-thrust controls and with flight instrument displays. Control forces on the wheel, column, and rudder pedals are provided by a hydraulic system coupled with an analog computer. The simulator provides variable-feel characteristics of stiffness, damping, coulomb friction, breakout forces, and inertia. The VMS provides a wide range of realistic flight trajectories necessary for computing accurate ground contours. The NASA VMS will be discussed in detail later in this presentation. An equally important part of the system for both ANOPP and VMS is the engine performance. This will also be discussed in the presentation.

Rawls, John, Jr.↗

Spacecraft flight control with the new phase space control law and optimal linear jet select

An autopilot designed for rotation and translation control of a rigid spacecraft is described. The autopilot uses reaction control jets as control effectors and incorporates a six-dimensional phase space control law as well as a linear programming algorithm for jet selection. The interaction of the control law and jet selection was investigated and a recommended configuration proposed. By means of a simulation procedure the new autopilot was compared with an existing system and was found to be superior in terms of core memory, central processing unit time, firings, and propellant consumption. But it is thought that the cycle time required to perform the jet selection computations might render the new autopilot unsuitable for existing flight computer applications, without modifications. The new autopilot is capable of maintaining attitude control in the presence of a large number of jet failures.

Bergmann, E. V.↗

Advanced techniques in reliability model representation and solution

The current tendency of flight control system designs is towards increased integration of applications and increased distribution of computational elements. The reliability analysis of such systems is difficult because subsystem interactions are increasingly interdependent. Researchers at NASA Langley Research Center have been working for several years to extend the capability of Markov modeling techniques to address these problems. This effort has been focused in the areas of increased model abstraction and increased computational capability. The reliability model generator (RMG) is a software tool that uses as input a graphical object-oriented block diagram of the system. RMG uses a failure-effects algorithm to produce the reliability model from the graphical description. The ASSURE software tool is a parallel processing program that uses the semi-Markov unreliability range evaluator (SURE) solution technique and the abstract semi-Markov specification interface to the SURE tool (ASSIST) modeling language. A failure modes-effects simulation is used by ASSURE. These tools were used to analyze a significant portion of a complex flight control system. The successful combination of the power of graphical representation, automated model generation, and parallel computation leads to the conclusion that distributed fault-tolerant system architectures can now be analyzed.

Palumbo, Daniel L.↗

Helicopter flight control system design and evaluation for NOE operations using controller inversion techniques

A flight control system design technique is described that allows rapid evaluation of candidate control laws using computer simulated trajectories. The two-step technique first computes the optimum trajectory for the basic aircraft, and then reconstructs the pilot's control displacements necessary to fly this trajectory, given a particular control system architecture. Since the flight control system itself does not add to the acceleration potential of the helicopter, one may evaluate several proposed control laws in terms of the resulting stick inputs for the same maneuver. The method is illustrated through application to implicit and explicit model-following control laws designed for a battlefield helicopter with and without an auxiliary propulsor. It is shown that the technique is a valuable aid for selection of promising control laws for further simulator studies and flight investigations.

Mckillip, Robert M., Jr.↗

Shuttle mission simulator

The simulator was designed to provide real time simulation capability for all phases of the Shuttle Transportation System orbital missions including prelaunch, ascent, onorbit operations, deorbit, entry, approach/landing, and rollout. Full mission continuity is provided in transition between these mission phases. Dual fixed and motion base crew stations, instructor/operator stations, and computer systems allow parallel, simultaneous crew training with either complex capable of being individually integrated with the mission control center. This integrated training capability allows flight control personnel training in the air/ground interface areas of tracking, telemetry (vehicle systems monitoring), uplink command control, and communications. With the exception of the simulated Data Processing System, which utilizes actual flight computers and associated flight software, all orbiter onboard systems are functionally simulated with extensive simulated malfunction capabilities. Additionally, crew out-the-window visual scenes, and aural cues are rigorously simulated.

Olasky, C.↗

Validation of a Mid-Fidelity Approach for Aircraft Stability and Control Characterization

This paper describes an efficient computational approach for aircraft aerodynamic model development intended for use in flight dynamics simulations. A commercial surface-vorticity flow solver called FlightStream is employed to predict performance, stability, and control characteristics for a NASA subscale electric vertical takeoff and landing aircraft in its isolated-airframe configuration. A framework is described to rapidly convert OpenVSP geometry into a form compatible with the FlightStream software. FlightStream predictions for the variation of aerodynamic force and moment coefficients with airflow angles and control surface deflection angles are compared to static wind-tunnel data to illustrate the process and assess the accuracy of FlightStream solutions. The results and approach presented in this paper are encouraging for use in rapid aerodynamic modeling and flight dynamics simulation development early in the aircraft design process.

aerodynamic modeling↗

Simulation Modeling for Off-Nominal Conditions - Where Are We Today?

The modeling of aircraft flight characteris4cs in off-nominal or otherwise adverse conditions has become increasingly important for simulation in the loss-of-control arena. Adverse conditions include environmentally-induced upsets such as wind shear or wake vortex encounters; off-nominal flight conditions, such as stall or departure; on-board systems failures; and structural failures or aircraft damage. Spirited discussions in the research community are taking place as to the fidelity and data requirements for adequate representation of vehicle dynamics under such conditions for a host of research areas, including recovery training, flight controls development, trajectory guidance/planning, and envelope limiting. The increasing need for multiple sources of data (empirical, computational, experimental) for modeling across a larger flight envelope leads to challenges in developing methods of appropriately applying or combining such data, particularly in a dynamic flight environment with a physically and/or aerodynamically asymmetric vehicle. Traditional simplifications and symmetry assumptions in current modeling methodology may no longer be valid. Furthermore, once modeled, challenges abound in the validation of flight dynamics characteristics in adverse flight regimes

Shah, Gautam H.↗

SCI Identification (SCIDNT) program user's guide

The computer program Linear SCIDNT which evaluates rotorcraft stability and control coefficients from flight or wind tunnel test data is described. It implements the maximum likelihood method to maximize the likelihood function of the parameters based on measured input/output time histories. Linear SCIDNT may be applied to systems modeled by linear constant-coefficient differential equations. This restriction in scope allows the application of several analytical results which simplify the computation and improve its efficiency over the general nonlinear case.

Source record↗

Multidisciplinary Expert-aided Analysis and Design (MEAD)

The MEAD Computer Program (MCP) is being developed under the Multidisciplinary Expert-Aided Analysis and Design (MEAD) Project as a CAD environment in which integrated flight, propulsion, and structural control systems can be designed and analyzed. The MCP has several embedded computer-aided control engineering (CACE) packages, a user interface (UI), a supervisor, a data-base manager (DBM), and an expert system (ES). The supervisor monitors and coordinates the operation of the CACE packages, the DBM; the ES, and the UI. The DBM tracks the control design process. Models created or installed by the MCP are tracked by date and version, and results are associated with the specific model version with which they were generated. The ES is used to relieve the control engineer from tedious and cumbersome tasks in the iterative design process. The UI provides the capability for a novice as well as an expert to utilize the MCP easily and effectively. The MCP version 2(MCP-2.0) is fully developed for flight control system design and analysis. Propulsion system modeling, analysis, and simulation is also supported; the same is true for structural models represented in state-space form. The ultimate goal is to cover the integration of flight, propulsion, and structural control engineering, including all discipline-specific functionality and interfaces. The current MCP-2.0 components and functionality are discussed.

Hummel, Thomas C.↗

Design, implementation and flight testing of PIF autopilots for general aviation aircraft

The designs of Proportional-Integrated-Filter (PIF) auto-pilots for a General Aviation (NAVION) aircraft are presented. The PIF autopilot uses the sampled-data regulator and command generator tracking to determine roll select, pitch select, heading select, altitude select and localizer/glideslope capture and hold autopilot modes. The PIF control law uses typical General Aviation sensors for state feedback, command error integration for command tracking, digital complementary filtering and analog prefiltering for sensor noise suppression, a control filter for computation delay accommodation and the incremental form to eliminate trim values in implementation. Theoretical developments described in detail, were needed to combine the sampled-data regulator with command generator tracking for use as a digital flight control system. The digital PIF autopilots are evaluated using closed-loop eigenvalues and linear simulations. The implementation of the PIF autopilots in a digital flight computer using a high order language (FORTRAN) is briefly described. The successful flight test results for each PIF autopilot mode is presented.

Broussard, J. R.↗