SEARCH · Search NASA

Results for “GLIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1989

High temperature creep behavior of single crystal gamma prime and gamma alloys

The creep behavior of single crystals of gamma-prime and gamma alloys were investigated and compared to the response of two-phase superalloys tested previously. High temperature deformation in the gamma alloys was characteristic of a climb-controlled mechanism, whereas the gamma-prime based materials exhibited glide-controlled creep behavior. The superalloys were much more creep resistant than their constituent phases, which indicates the importance of the gamma/gamma-prime interface as a barrier for dislocation motion during creep.

Nathal, M. V.↗

NASA NTRS1990

Aerodynamic separation and glideback of a Mach 3 staged booster

A study has been conducted of the staging maneuver for a two-stage, vertical-takeoff, launch vehicle and the subsequent glideback of the booster to a launch site runway. The booster and orbiter are both winged, fully reusable, and have liquid rocket main propulsion. for the staging maneuver, which nominally occurs at Mach 3, a flight control system and separation technique were devised which produced successful separations over a wide range of staging angles of attack. A guidance algorithm was developed for the unpowered glide-back of the booster from the completion of the staging maneuver to touchdown on a runway in the vicinity of the launch site. Using this guidance technique, the booster successfully touched down on the runway while being subjected to a wide range of seasonal and perturbed atmospheric conditions with and without wids as well as errors in staging state conditions and errors in predicted aerodynamics.

Naftel, J. C.↗

NASA NTRS1990

Maximum orbit plane change with heat-transfer-rate considerations

Two aerodynamic maneuvers are considered for maximizing the plane change of a circular orbit: gliding flight with a maximum thrust segment to regain lost energy (aeroglide) and constant altitude cruise with the thrust being used to cancel the drag and maintain a high energy level (aerocruise). In both cases, the stagnation heating rate is limited. For aeroglide, the controls are the angle of attack, the bank angle, the time at which the burn begins, and the length of the burn. For aerocruise, the maneuver is divided into three segments: descent, cruise, and ascent. During descent the thrust is zero, and the controls are the angle of attack and the bank angle. During cruise, the only control is the assumed-constant angle of attack. During ascent, a maximum thrust segment is used to restore lost energy, and the controls are the angle of attack and bank angle. The optimization problems are solved with a nonlinear programming code known as GRG2. Numerical results for the Maneuverable Re-entry Research Vehicle with a heating-rate limit of 100 Btu/ft(2)-s show that aerocruise gives a maximum plane change of 2 deg, which is only 1 deg larger than that of aeroglide. On the other hand, even though aerocruise requires two thrust levels, the cruise characteristics of constant altitude, velocity, thrust, and angle of attack are easy to control.

Lee, J. Y.↗

NASA NTRS1989

Cyclic deformation, fatigue and fatigue crack propagation in Ni-base alloys

Ni-base superalloys' cumulative glide behavior, damage accumulation, low-cycle fatigue, and crack propagation characteristics are directly dependent on deformation behavior which is in turn a strong function of microstructural characteristics. Microstructural instabilities and environmental interactions become additional factors at elevated temperatures. An account is presently given of microstructural, chemical, and processing techniques that may be used to obtain the properties that appear most critical or desirable in specific applications.

Antolovich, Stephen D.↗

NASA NTRS1990

An expert system for wind shear avoidance

The principal objectives are to develop methods for assessing the likelihood of wind shear encounter (based on real-time information in the cockpit), for deciding what flight path to pursue (e.g., takeoff abort, landing go-around, or normal climbout or glide slope), and for using the aircraft's full potential for combating wind shear. This study requires the definition of both deterministic and statistical techniques for fusing internal and external information, for making go/no-go decisions, and for generating commands to the aircraft's autopilot and flight directors for both automatic and manually controlled flight. The expert system for pilot aiding is based on the results of the FAA Windshear Training Aids Program, a two-volume manual that presents an overview, pilot guide, training program, and substantiating data that provides guidelines for this initial development. The Windshear Safety Advisor expert system currently contains over 140 rules and is coded in the LISP programming language for implementation on a Symbolics 3670 LISP Machine.

Stengel, Robert F.↗

NASA NTRS1991

Effects of ultravacuum and space environment on contact ohmic resistance (AO 138-11)

The experiment was aimed at checking compatibility of the aluminum conductors with conventional conductors and contacts under different conditions of manufacturing (mechanical or magnetostrictive crimping) and storage in laboratory or in long-duration space environment. The electrical characteristics of connections built from nickel-plated conductors and glided copper contacts were noted to vary over the duration of the experiment. These variations are unrelated with the crimping or storage conditions or with metal pairing (nickel-plated aluminum/tinned or silver copper). Such evolutions, even slight, are detrimental to connection quality. The same observations hold for some like connections subjected to long-duration thermal cycles. Therefore, work on aluminum technology was reoriented toward a silver aluminum conductor/ golded aluminum contact solution. The first evaluation test performed according to this definition have yielded satisfactory results.

Assie, Jean Pierre↗

NASA NTRS1991

Guidance and control analysis of the entry of a lifting body personnel launch vehicle

NASA is currently involved in definition studies of a Personnel Launch System (PLS) that could be used to transport people to and from low-earth orbit. This vehicle would serve both to complement the Space Shuttle and to provide alternative access to space in the event the Space Shuttle fleet were unavailable for a prolonged period. The PLS would consist of a manned spacecraft launched by an expendable vehicle, e.g., Titan 4. One promising candidate for the manned component of the PLS is the NASA Langley Research Center HL-20 lifting body. Many studies are currently underway to assess this vehicle, and one of the main areas of study is the development of the capability to successfully enter, glide to the landing site, and land. To provide this capability, guidance and control algorithms have been developed, incorporated into a six-degree-of-freedom simulation, and evaluation in the presence of off-nominal atmospheric conditions, consisting of both density variations and steady-state winds. In addition, the impact of atmospheric turbulence was examined for the portion of flight from Mach 3.5 to touchdown. This analysis showed that the vehicle remained controllable and could successfully land even in the presence of off-nominal atmospheric conditions.

Powell, Richard W.↗

NASA NTRS1991

Directivity and prediction of low frequency rotor noise

Acoustic data obtained over a large horizontal plane under the model rotor and digitally filtered in order to determine the low-frequency content near the blade passage frequency is analyzed. Focus is placed on the directivity of low-frequency noise, and the changes in directivity as a function of the descent glide slope angle and advance ratio are presented and compared with predicted directivity results. The differences between the data and prediction are discussed for two observer positions, one below and on the rotor axis, and the other 60 degrees down from the horizontal. It is demonstrated that for the latter position, blade-vortex interaction noise is strong when it occurs, and the loading at the low frequencies is significantly affected during blade-vortex interactions.

Burley, C. L.↗

NASA NTRS1991

Grain boundary sliding behaviour of copper and alpha brass at intermediate temperatures

The role of grain boundary sliding in copper and Cu-30 pct Zn in the temperature range 0.50-0.72 Tm, where Tm is the absolute melting point of the material, is examined. First, sliding data obtained on these materials are presented. The results indicate that the stress exponent for sliding is similar to that for lattice deformation, while the activation energy for sliding varies between 0.5 and 1.6 of the activation energy for creep. Several models proposed for grain boundary sliding are discussed, and it is shown that they do not account for the observed results on copper and alpha brass. A phenomenological model is proposed, where it is assumed that grain boundary sliding results from the glide of dislocations on secondary slip planes.

Raj, S. V.↗

NASA NTRS1991

Ascent performance issues of a vertical-takeoff rocket launch vehicle

Advanced manned launch systems studies under way at the NASA Langley Research Center are part of a broader effort that is examining options for the next manned space transportation system to be developed by the United States. One promising concept that uses near-term technologies is a fully reusable, two-stage vertical-takeoff rocket vehicle. This vehicle features parallel thrusting of the booster and orbiter with the booster cross-feeding the propellant to the orbiter until staging. In addition, after staging, the booster glides back unpowered to the launch site. This study concentrated on two issues that could affect the ascent performance of this vehicle. The first is the large gimbal angle range required for pitch trim until staging because of the propellant cross-feed. Results from this analysis show that if control is provided by gimballing of the rocket engines, they must gimbal greater than 20 deg, which is excessive when compared with current vehicles. However, this analysis also showed that this limit could be reduced to 10 deg if gimballing were augmented by throttling the booster engines. The second issue is the potential influence of off-nominal atmospheric conditions (density and winds) on the ascent performance. This study showed that a robust guidance algorithm could be developed that would insure accurate insertion, without prelaunch atmospheric knowledge.

Powell, Richard W.↗

NASA NTRS1991

Creep behavior of copper at intermediate temperatures. II - Surface microstructural observations. III - A comparison with theory

Three different types of microstructural slip features are noted to occur during the creep of Cu at 0.46-0.72 of absolute melting point. While single slip is associated with higher temperatures and lower stresses, complex wavy slip features are observed at higher temperatures and higher stresses as well as with increasing strains: suggesting the importance of cross-slip mechanisms. At lower temperatures and higher stresses the multiple-slip morphologies observed indicate that cross-slip mechanisms may control the creep of polycrystalline Cu only over a limited stress and temperature range. A phenomenological model is proposed which assumes that (1) cell boundaries within subgrains act as both sources of, and obstacles to, gliding dislocations, and (2) dislocation annihilation occurs at the cell boundaries by climb and cross-slip.

Raj, S. V.↗

NASA NTRS1991

A compensatory algorithm for the slow-down effect on constant-time-separation approaches

In seeking methods to improve airport capacity, the question arose as to whether an electronic display could provide information which would enable the pilot to be responsible for self-separation under instrument conditions to allow for the practical implementation of reduced separation, multiple glide path approaches. A time based, closed loop algorithm was developed and simulator validated for in-trail (one aircraft behind the other) approach and landing. The algorithm was designed to reduce the effects of approach speed reduction prior to landing for the trailing aircraft as well as the dispersion of the interarrival times. The operational task for the validation was an instrument approach to landing while following a single lead aircraft on the same approach path. The desired landing separation was 60 seconds for these approaches. An open loop algorithm, previously developed, was used as a basis for comparison. The results showed that relative to the open loop algorithm, the closed loop one could theoretically provide for a 6 pct. increase in runway throughput. Also, the use of the closed loop algorithm did not affect the path tracking performance and pilot comments indicated that the guidance from the closed loop algorithm would be acceptable from an operational standpoint. From these results, it is concluded that by using a time based, closed loop spacing algorithm, precise interarrival time intervals may be achievable with operationally acceptable pilot workload.

Abbott, Terence S.↗

NASA NTRS1991

An Exploratory Exercise in Taguchi Analysis of Design Parameters: Application to a Shuttle-to-space Station Automated Approach Control System

The chief goals of the summer project have been twofold - first, for my host group and myself to learn as much of the working details of Taguchi analysis as possible in the time allotted, and, secondly, to apply the methodology to a design problem with the intention of establishing a preliminary set of near-optimal (in the sense of producing a desired response) design parameter values from among a large number of candidate factor combinations. The selected problem is concerned with determining design factor settings for an automated approach program which is to have the capability of guiding the Shuttle into the docking port of the Space Station under controlled conditions so as to meet and/or optimize certain target criteria. The candidate design parameters under study were glide path (i.e., approach) angle, path intercept and approach gains, and minimum impulse bit mode (a parameter which defines how Shuttle jets shall be fired). Several performance criteria were of concern: terminal relative velocity at the instant the two spacecraft are mated; docking offset; number of Shuttle jet firings in certain specified directions (of interest due to possible plume impingement on the Station's solar arrays), and total RCS (a measure of the energy expended in performing the approach/docking maneuver). In the material discussed here, we have focused on single performance criteria - total RCS. An analysis of the possibility of employing a multiobjective function composed of a weighted sum of the various individual criteria has been undertaken, but is, at this writing, incomplete. Results from the Taguchi statistical analysis indicate that only three of the original four posited factors are significant in affecting RCS response. A comparison of model simulation output (via Monte Carlo) with predictions based on estimated factor effects inferred through the Taguchi experiment array data suggested acceptable or close agreement between the two except at the predicted optimum point, where a difference outside a rule-of-thumb bound was observed. We have concluded that there is most likely an interaction effect not provided for in the original orthogonal array selected as the basis for our experimental design. However, we feel that the data indicates that this interaction is a mild one and that inclusion of its effect will not alter the location of the optimum.

Deal, Don E.↗

NASA NTRS1992

Critical soft landing technology issues for future US space missions

A programmatic need for research and development to support parachute-based landing systems has not existed since the end of the Apollo missions in the mid-1970s. Now, a number of planned space programs require advanced landing capabilities for which the experience and technology base does not currently exist. New requirements for landing on land with controllable, gliding decelerators and for more effective impact attenuation devices justify a renewal of the landing technology development effort that existed during the Mercury, Gemini, and Apollo programs. A study was performed to evaluate the current and projected national capability in landing systems and to identify critical deficiencies in the technology base required to support the Assured Crew Return Vehicle and the Two-Way Manned Transportation System. A technology development program covering eight landing system performance issues is recommended.

Macha, J. M.↗

NASA NTRS1991

KSC off-runway contingency operation - Mode 7

The possibility of a mishap during a space shuttle landing at Kennedy Space Center (KSC) dictates the need for plans to rescue astronauts from areas other than the Shuttle Landing Facility (SLF). All shuttle landings are unpowered, gliding flight maneuvers, and a deviation from the planned flight profile could result in a shuttle landing or crashing somewhere other than the SLF runway. The geography of the Kennedy Space Center makes helicopter airlifting the only universal means of transportation for the rescue crew. This rescue crew is composed of KSC contractor fire-rescuemen who would ride to the crash scene on USAF HH-3 helicopters. These crews are provided with personal protective suits and training in shallow water, swamp, and dry land rescues. They aid the egress of the crew to a safe area for helicopter pickup and subsequent triage and medevac.

Maples, Arthur↗

NASA NTRS1991

Flow and fracture behavior of NiAl in relation to the brittle-to-ductile transition temperature

NiAl has only three independent slip systems operating at low and intermediate temperatures whereas five independent deformation mechanisms are required to satisfy the von Mises criterion for general plasticity in polycrystalline materials. Yet, it is generally recognized that polycrystalline NiAl can be deformed extensively in compression at room temperature and that limited tensile ductility can be obtained in extruded materials. In order to determine whether these results are in conflict with the von Mises criterion, tension and compression tests were conducted on powder-extruded, binary NiAl between 300 and 1300 K. The results indicate that below the brittle-to-ductile transition temperature (BDTT) the failure mechanism in NiAl involves the initiation and propagation of cracks at the grain boundaries which is consistent with the von Mises analysis. Furthermore, evaluation of the flow behavior of NiAl indicates that the transition from brittle to ductile behavior with increasing temperature coincides with the onset of recovery mechanisms such as dislocation climb. The increase in ductility above the BDTT is therefore attributed to the climb of the 001 line type dislocations which in combination with dislocation glide enable grain boundary compatibility to be maintained at the higher temperatures.

Noebe, R. D.↗

NASA NTRS1991

Fatigue damage accumulation in nickel prior to crack initiation

The accumulation of lattice defects during fatigue cycling of nickel was investigated by electrical resistivity measurements, positron annihilation lifetime spectroscopy and transmission electron microscopy. Dislocations and vacancy clusters were found to be the main defect types. During cycling of axial and flexural samples at constant load amplitude, the dislocations form a saturated structure early in the fatigue life. This saturated structure consists of a cellular dislocation matrix, in which persistent slip bands (PSBs) begin to operate after the saturation has been established. Vacancies and vacancy clusters are formed during fatigue as a consequence of repetitive dislocation glide in the PSB structure. When PSBs operate, the matrix is assumed to be dormant, allowing vacancies to accumulate preferentially in the PSBs. The increase in vacancy concentration then accounts for the monotonic accumulation of fatigue damage, which points to the importance of vacancy accumulation as a precursor to crack nucleation.

Grobstein, T. L.↗

NASA NTRS1992

Rheology of water-silicate mixtures at low temperatures

Lab studies of the effects of hard particulates on the rheology of ice have been mainly directed at the evolution of the Galilean satellites, but yield results that may be applicable to the rheology of the Martian polar caps. The experiments have explored the ductile rheology as well as brittle behavior of water + particulate (mainly quartz) mixtures in particulate volume fractions ranging from 0.001 to 0.56, particulate sizes 1 to 150 microns, temperatures 77 to 224 K, and deformation rates 3.5 x 10(exp -7) to 3.5 x 10(exp -4)/s, under confining pressures of 50 to 100 MPa. Particulates act mainly to strengthen the material in the ductile field, although work by others has shown that very close to the melting temperature hard particulates can actually cause softening. So called dispersion hardening by the Orowan mechanism of pinning glide dislocations, often exploited in metallurgy for strengthening materials, appears not to be an issue in ice except at very low temperatures, less than approx. 135 K.

Durham, William B.↗