Search NASA⌕ Search

SEARCH · Search NASA

Results for “HELICOPTERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Simulation study of intracity helicopter operations under instrument conditions to category 1 minimums

A fixed-base simulator study was conducted to define pilot workload and task performance associated with instrument flight operations for an intracity helicopter passenger service. Displays considered necessary to provide a minimal capability under Instrument Flight Rules conditions were used to fly a representative commercial helicopter route structure in the New York area, with each terminal assumed to be equipped with a precision approach guidance system. A cross section of pilots participated as test subjects, and despite the high workload level, the results indicated that for the assumptions employed, minimums of 61 m (200 ft) ceiling and 805 m (0.5 mile) visibility were feasible.

Callan, W. M.↗
NASA NTRS1975

Development of an analysis for the determination of coupled helicopter rotor/control system dynamic response. Part 2: Program listing

A theoretical analysis is developed for a coupled helicopter rotor system to allow determination of the loads and dynamic response behavior of helicopter rotor systems in both steady-state forward flight and maneuvers. The effects of an anisotropically supported swashplate or gyroscope control system and a deformed free wake on the rotor system dynamic response behavior are included.

Sutton, L. R.↗
NASA NTRS1975

An analytical evaluation of airfoil sections for helicopter rotor applications

An analytical technique was used to evaluate airfoils for helicopter rotor application. This technique permits assessment of the influences of airfoil geometric variations on drag divergence Mach number at lift coefficients from near zero to near maximum lift. Analytical results presented in this paper indicate the compromises in drag divergence Mach number which result from changes in (1) thickness ratio, (2) location of maximum thickness, (3) leading-edge radius, (4) camber addition, and (5) location of maximum camber of NACA four- and five-digit-series airfoils and some 6-series airfoils of potential interest for helicopters. Examples of airfoil sections which combine several of the geometric changes favorable to both advancing and retreating section performance have been presented.

Bingham, G. J.↗
NASA NTRS1975

Development of an analysis for the determination of coupled helicopter rotor/control system dynamic response. Part 1: Analysis and applications

A theoretical analysis is developed for a coupled helicopter rotor system to allow determination of the loads and dynamic response behavior of helicopter rotor systems in both steady-state forward flight and maneuvers. The effects of an anisotropically supported swashplate or gyroscope control system and a deformed free wake on the rotor system dynamic response behavior are included in the analysis.

Sutton, L. R.↗
NASA NTRS1975

A simulation study of active feedback supression of dynamic response in helicopter rotor blades

A parameter study is presented for active feedback control applied to a helicopter rotor blade during forward flight. The study was performed on an electromechanical apparatus which included a mechanical model rotor blade and electronic analog simulation of interaction between blade deflections and aerodynamic loading. Blade response parameters were obtained for simulated vortex impinging at the blade tip at one pulse per revolution, and for a pulse which traveled from the blade tip toward its root. Results show that the response in a 1 - 10-per-rev frequency band is diminished by the feedback action, but at the same time responses at frequencies above 10-per-rev become increasingly more prominent with increased feedback amplitude, and can even lead to instability at certain levels. It appears that the latter behavior results from limitations of the laboratory simulation apparatus, rather than genuine potential behavior for a prototype helicopter.

Kana, D. D.↗
NASA NTRS1975

Finite element analysis using NASTRAN applied to helicopter transmission vibration/noise reduction

A finite element NASTRAN model of the complete forward rotor transmission housing for the Boeing Vertol CH-47 helicopter was developed and applied to reduce transmission vibration/noise at its source. In addition to a description of the model, a technique for vibration/noise prediction and reduction is outlined. Also included are the dynamic response as predicted by NASTRAN, test data, the use of strain energy methods to optimize the housing for minimum vibration/noise, and determination of design modifications which will be manufactured and tested. The techniques presented are not restricted to helicopters but are applicable to any power transmission system. The transmission housing model developed can be used further to evaluate static and dynamic stresses, thermal distortions, deflections and load paths, fail-safety/vulnerability, and composite materials.

Howells, R. W.↗
NASA NTRS1975

Analysis of helicopter rotor blade torsional oscillations due to stall

An analysis of stall-induced helicopter rotor blade torsional oscillations was carried out, the primary objectives being to predict the onset and severity of the oscillations and their relationship to aircraft and blade parameters. Blade flapping, flapwise bending, and torsional degrees of freedom were taken into account, with radial variation in aerodynamic loading determined from a previously developed dynamic stall model. Results of analyses were compared with data from flight tests of helicopters. Analyses were carried out while parametrically varying blade vibrational characteristics. It was found that the amplitudes of the higher harmonics of torsional oscillations can be significantly reduced by either reducing the torsional natural frequency or introducing viscous damping in the torsional degree of freedom. A preliminary investigation was conducted to determine the feasibility and practicality of alleviating the stall problem by means of boundary layer control. The results indicate that boundary layer control would be effective in reducing the higher harmonics of torsional oscillations due to stall and that its implementation would not require excessive power or suction rates.

Crimi, P.↗
NASA NTRS1975

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 1

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacture of large helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D helicopter was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR-49/epoxy skin and graphite/epoxy frames and stringers. To support the selection of this specific design concept a materials study was conducted to develop and select a cure compatible graphite and KEVLAR-49/epoxy resin system, and a foam system capable of maintaining shape and integrity under the processing conditions established. The materials selected were, Narmco 5209/Thornel T-300 graphite, Narmco 5209/KEVLAR-49 woven fabric, and Stathane 8747 polyurethane foam. Eight specimens were fabricated, representative of the frame, stringer, and splice joint attachments. Evaluation of the results of analysis and test indicate that design predictions are good to excellent except for some conservatism of the complex frame splice.

Adams, K. M.↗
NASA NTRS1975

Development of circumferential seal for helicopter transmissions: Results of bench and flight tests

A modified circumferential segmented ring seal was designed for direct replacement of a helicopter transmission elastomeric lip seal operating on a shaft diameter of 13.91 centimeters (5.481 in.) at sliding velocities to 52.48 m/sec (10 330 ft/min). The modifications involved the garter spring tension, shaft roundness, seal housing flatness, and pumping grooves to inhibit leakage. Operation of the seals in bench tests under simulated helicopter transmission conditions revealed that the seal leakage rate was within acceptable limits and that the wear rate was negligible. The low leakage and wear rates were confirmed in flight tests of 600 and 175 hours (sliding speed, 48.11 m/sec (9470 ft/min)). An additional 200 hours of air worthiness qualification testing (aircraft tie down) demonstrated that the seal can operate at the advanced sliding conditions of 52.48 m/sec (10 330 ft/min).

Strom, T. N.↗
NASA NTRS1975

A model-based analysis of a display for helicopter landing approach

A control theoretic model of the human pilot was used to analyze a baseline electronic cockpit display in a helicopter landing approach task. The head down display was created on a stroke written cathode ray tube and the vehicle was a UH-1H helicopter. The landing approach task consisted of maintaining prescribed groundspeed and glideslope in the presence of random vertical and horizontal turbulence. The pilot model was also used to generate and evaluate display quickening laws designed to improve pilot vehicle performance. A simple fixed base simulation provided comparative tracking data.

Hess, R. A.↗
NASA NTRS1975

A study of noise guidelines for community acceptance of civil-helicopter operations

The Day-Night Noise Level, which takes tonal content, duration, and number of operations into account, and penalizes night-time noise, is found to be the best available index for rating community annoyance caused by aircraft. A Day-Night level of 60 for communities with ambient noise levels up to 58 dBA, and a level of 2 dBA higher than the ambient for communities where it is above 58 dBA, is proposed as acceptable. Evaluation of a large transport helicopter showed that the guidelines do not impose severe economic penalties on helicopter operations.

Munch, C. L.↗
NASA NTRS1975

Vehicle for civil helicopter ride quality research

A research aircraft for investigating the factors involved in civil helicopter operations was developed for NASA Langley Research Center. The aircraft is a reconfigured 17000 kg (36000 lb) military transport helicopter. The basic aircraft was reconfigured with advanced acoustic treatment, air-conditioning, and a 16-seat airline cabin. During the spring of 1975, the aircraft was flight tested to measure interior environment characteristics - noise and vibration - and was flown on 60 subjective flight missions with over 600 different subjects. Data flights established noise levels somewhat higher than expected, with a pure tone at 1400 Hz and vertical vibration levels between 0.07g and 0.17g. The noise and vibration levels were documented during subjective flight evaluations as being the primary source of discomfort. The aircraft will be utilized to document in detail the impact of various noise and vibration levels on passenger comfort during typical short-haul missions.

Snyder, W. J.↗
NASA NTRS1977

The effect of variations in controls and displays on helicopter instrument approach capability

A flight investigation was conducted with a variable stability helicopter to determine the effects of variations in controls and displays on helicopter instrument approach capabilities. The baseline instrument approach task was a decelerating approach to a hover along a 6 deg glide slope. Pilot evaluations were obtained for both the constant speed part of the task and the deceleration and hover part of the task. The attitude stability augmentation system (SAS) was strongly preferred over the rate SAS because the aircraft had a divergent pitch response. From a display variation standpoint, it was not possible to decelerate to a hover in a consistent manner, regardless of the control system employed, with situation information only. In particular, the deceleration and hover part of the task was unacceptable without flight director command information.

Niessen, F. R.↗
NASA NTRS1976

Research requirements to reduce empty weight of helicopters by use of advanced materials

Utilization of the new, lightweight, high-strength, aerospace structural-composite (filament/matrix) materials, when specifically designed into a new aircraft, promises reductions in structural empty weight of 12 percent at recurring costs competive with metals. A program of basic and applied research and demonstration is identified with the objective of advancing the state of the art to the point where civil helicopters are confidently designed, produced, certified, and marketed by 1985. A structural empty-weight reduction of 12 percent was shown to significantly reduce energy consumption in modern high-performance helicopters.

Hoffstedt, D. J.↗
NASA NTRS1976

Research requirements for development of regenerative engines for helicopters

The improved specific fuel consumption of the regenerative engine was compared to a simple-cycle turboshaft engine. The performance improvement and fuel saving are obtained at the expense of increased engine weight, development and production costs, and maintenance costs. Costs and schedules are estimated for the elements of the research and development program. Interaction of the regenerative engine with other technology goals for an advanced civil helicopter is examined, including its impact on engine noise, hover and cruise performance, helicopter empty weight, drive-system efficiency and weight, one-engine-inoperative hover capability, and maintenance and reliability.

Semple, R. D.↗
NASA NTRS1976

Research requirements for the reduction of helicopter vibration

All prospective approaches to the reduction of helicopter vibrations were searched to establish insight for the planning of a corrective research program. The state of the art as revealed in the literature is summed up and followed by a discussion of state-of-the-art solutions and of identified technological gaps. It is applicable to all helicopters without regard to size. Extending the historic trend toward lower vibration levels will require the successful application of principles which isolate the fuselage from the rotor systems. Simplicity of the necessary isolation systems should be facilitated by providing other refinements of the dynamic design of the system.

Doman, G. S.↗
NASA NTRS1976

Research requirements for emergency power to permit hover-one-engine-inoperative helicopter operation

The research and technology demonstration requirements to achieve emergency-power capability for a civil helicopter are documented. The goal for emergency power is the ability to hover with one engine inoperative, transition to minimum-power forward flight, and continue to a safe landing where emergency power may or may not be required. The best method to obtain emergency power is to augment the basic engine power by increasing the engine's speed and turbine-inlet temperature, combined with water-alcohol injection at the engine inlet. Other methods, including turbine boost power and flywheel energy, offer potential for obtaining emergency power for minimum time durations. Costs and schedules are estimated for a research and development program to bring emergency power through a hardware-demonstration test. Interaction of engine emergency-power capability with other helicopter systems is examined.

Yost, J. H.↗