SEARCH · Search NASA

Results for “HIGH THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1979

High-performance wings with significant leading-edge thrust at supersonic speeds

A new class of curved-leading-edge wings with which significant levels of leading-edge thrust may be achieved at moderate supersonic speeds is suggested. A recent analysis of the factors limiting such leading-edge thrust has led to a new method for the prediction of attainable leading-edge thrust from subsonic through supersonic speeds for wings of arbitrary planform. Recent supersonic tests of a new wing shape, which largely meets design criteria given by the new prediction method, give evidence of significant levels of leading-edge thrust. The consequent unusually high levels of aerodynamic performance should renew interest in supersonic-cruise vehicle design in general and in cruise-speed selection in particular.

Robins, A. W.↗

NASA NTRS1980

Investigation of advanced thrust vectoring exhaust systems for high speed propulsive lift

The paper presents the results of a wind tunnel investigation conducted at the NASA-Langley research center to determine thrust vectoring/induced lift characteristics of advanced exhaust nozzle concepts installed on a supersonic tactical airplane model. Specific test objectives include: (1) basic aerodynamics of a wing body configuration, (2) investigation of induced lift effects, (3) evaluation of static and forward speed performance, and (4) the effectiveness of a canard surface to trim thrust vectoring/induced lift forces and moments.

Hutchison, R. A.↗

NASA NTRS2008

Pressure and Thrust Measurements of a High-Frequency Pulsed Detonation Tube

This paper describes measurements of a small-scale, high-frequency pulsed detonation tube. The device utilized a mixture of H2 fuel and air, which was injected into the device at frequencies of up to 1200 Hz. Pulsed detonations were demonstrated in an 8-inch long combustion volume, at about 600 Hz, for the quarter wave mode of resonance. The primary objective of this experiment was to measure the generated thrust. A mean value of thrust was measured up to 6.0 lb, corresponding to H2 flow based specific impulse of 2970 s. This value is comparable to measurements in H2-fueled pulsed detonation engines (PDEs). The injection and detonation frequency for this new experimental case was much higher than typical PDEs, where frequencies are usually less than 100 Hz. The compact size of the device and high frequency of detonation yields a thrust-per-unit-volume of approximately 2.0 pounds per cubic inch, and compares favorably with other experiments, which typically have thrust-per-unit-volume of order 0.01 pound per cubic inch. This much higher volumetric efficiency results in a potentially much more practical device than the typical PDE, for a wide range of potential applications, including high-speed boundary layer separation control, for example in hypersonic engine inlets, and propulsion for small aircraft and missiles.

Nguyen, N.↗

NASA NTRSDate not supplied

Nuclear Fusion Space Propulsion Research, Experimentation, Theory Development, and Systems Analysis Efforts Led by the NASA Glenn Research Center (1994-2004)

This review paper summarizes work performed from 1994 to 2004 by a several interrelated government, academic, and industry teams led by the NASA Glenn Research Center. The nuclear fusion space propulsion system concept was predicated on a spherical torus reactor, which enabled manned missions to the outer planets in less than one year. Moderate thrust levels (1,000’s lbf)from direct nuclear fusion exhaust plasma via a magnetic nozzle enabled high thrust-to-weight. An entire vehicle conceptual design, including an artificial gravity crew habitat, was created by the NASA Glenn Research Center. The proof of concept experiment test article and facility upgrade was performed at the Ohio State University which also included staff from the Ohio Aerospace Institute and Science Applications International Corporation.The governing equations for the plasma physics theory of magnetic nozzle operation were derived by the Los Alamos National Laboratory. A preliminary investigation of a proof of concept test utilizing Coaxial Helicity Ejection as a means to supply plasma for propulsion at the National Spherical Torus Experiment reactor was outlined by the Princeton Plasma Physics Laboratory. An industry standard on nuclear fusion propulsion conceptual design was created by two AIAA teams. Despite extremely modest funding levels, significant progress was made advancing the state of the art.The result was a coordinated conceptual, theoretical, and experimental design effort to guide fusion space propulsion development.

Nuclear fusion↗

NASA NTRS2008

Pressure and Thrust Measurements of a High-Frequency Pulsed-Detonation Actuator

This paper describes the development of a small-scale, high-frequency pulsed detonation actuator. The device utilized a fuel mixture of H2 and air, which was injected into the device at frequencies of up to 1200 Hz. Pulsed detonations were demonstrated in an 8-inch long combustion volume, at approx.600 Hz, for the lambda/4 mode. The primary objective of this experiment was to measure the generated thrust. A mean value of thrust was measured up to 6.0 lb, corresponding to specific impulse of 2611 s. This value is comparable to other H2-fueled pulsed detonation engines (PDEs) experiments. The injection and detonation frequency for this new experimental case was approx.600 Hz, and was much higher than typical PDEs, where frequencies are usually less than 100 Hz. The compact size of the model and high frequency of detonation yields a thrust-per-unit-volume of approximately 2.0 lb/cu in, and compares favorably with other experiments, which typically have thrust-per-unit-volume values of approximately 0.01 lb/cu in.

Nguyen, Namtran C.↗

NASA NTRS2005

Experimental Study of a Pulse Detonation Engine Driven Ejector

Results of an experimental effort on pulse detonation driven ejectors are presented and discussed. The experiments were conducted using a pulse detonation engine (PDE)/ejector setup that was specifically designed for the study. The results of various experiments designed to probe different aspects of the PDE/ejector setup are reported. The baseline PDE was operated using ethylene (C2H4) as the fuel and an oxygen/nitrogen (O2 + N2) mixture at an equivalence ratio of one. The PDE only experiments included propellant mixture characterization using a laser absorption technique, high fidelity thrust measurements using an integrated spring-damper system, and shadowgraph imaging of the detonation/shock wave structure emanating from the tube. The baseline PDE thrust measurement results are in excellent agreement with experimental and modeling results reported in the literature. These PDE setup results were then used as a basis for quantifying thrust augmentation for various PDE/ejector setups with constant diameter ejector tubes and various detonation tube/ejector tube overlap distances. The results show that for the geometries studied here, a maximum thrust augmentation of 24% is achieved. Further increases are possible by tailoring the ejector geometry based on CFD predictions conducted elsewhere. The thrust augmentation results are complemented by shadowgraph imaging of the flowfield in the ejector tube inlet area and high frequency pressure transducer measurements along the length of the ejector tube.

Santoro, Robert J.↗

NASA NTRS2010

Advanced Space Fission Propulsion Systems

Fission has been considered for in-space propulsion since the 1940s. Nuclear Thermal Propulsion (NTP) systems underwent extensive development from 1955-1973, completing 20 full power ground tests and achieving specific impulses nearly twice that of the best chemical propulsion systems. Space fission power systems (which may eventually enable Nuclear Electric Propulsion) have been flown in space by both the United States and the Former Soviet Union. Fission is the most developed and understood of the nuclear propulsion options (e.g. fission, fusion, antimatter, etc.), and fission has enjoyed tremendous terrestrial success for nearly 7 decades. Current space nuclear research and technology efforts are focused on devising and developing first generation systems that are safe, reliable and affordable. For propulsion, the focus is on nuclear thermal rockets that build on technologies and systems developed and tested under the Rover/NERVA and related programs from the Apollo era. NTP Affordability is achieved through use of previously developed fuels and materials, modern analytical techniques and test strategies, and development of a small engine for ground and flight technology demonstration. Initial NTP systems will be capable of achieving an Isp of ~900 s at a relatively high thrust-to-weight ratio. The development and use of first generation space fission power and propulsion systems will provide new, game changing capabilities for NASA. In addition, development and use of these systems will provide the foundation for developing extremely advanced power and propulsion systems capable of routinely and affordably accessing any point in the solar system. The energy density of fissile fuel (8 x 10(exp 13) Joules/kg) is more than adequate for enabling extensive exploration and utilization of the solar system. For space fission propulsion systems, the key is converting the virtually unlimited energy of fission into thrust at the desired specific impulse and thrust-to-weight ratio. This presentation will discuss potential space fission propulsion options ranging from first generation systems to highly advanced systems. Ongoing research that shows promise for enabling second generation NTP systems with Isp greater than 1000 s will be discussed, as will the potential for liquid, gas, or plasma core systems. Space fission propulsion systems could also be used in conjunction with simple (water-based) propellant depots to enable routine, affordable missions to various destinations (e.g. moon, Mars, asteroids) once in-space infrastructure is sufficiently developed. As fuel and material technologies advance, very high performance Nuclear Electric Propulsion (NEP) systems may also become viable. These systems could enable sophisticated science missions, highly efficient cargo delivery, and human missions to numerous destinations. Commonalities between NTP, fission power systems, and NEP will be discussed.

Houts, Michael G.↗

NASA NTRS1972

Analysis of a supersonic-combustion rocket concept

A preliminary analysis has been made of a supersonic-combustion rocket engine concept using hydrogen and oxygen propellants. The ejector action of a separate small rocket motor is employed to pump the propellants to high stagnation pressures and supersonic velocities. Therefore complicated heavy turbopumps are eliminated and cooling problems of a sonic throat are reduced. The results of the study show that vacuum specific impulse levels as high as a conventional rocket having the same chamber pressure as the drive motor are possible. The supersonic-combustion rocket would be an attractive alternate for a high-altitude low-thrust conventional rocket operating with a pressure feed propellant system. It would also be a convenient technique for obtaining extremely high thrusts without the need for developing corresponding large turbopumps.

Franciscus, L. C.↗

NASA NTRS1992

Low-Isp derated ion thruster operation

The performance and lifetime expectations of 30 cm xenon ion thruster technology at low values of specific impulse were evaluated, with emphasis on 1000-2500 s operation. Power levels of up to 2.0 kW, appropriate for auxiliary and orbit maneuvering propulsion, were processed at thrust-to-power ratios up to 57 mN/kW. These tests were conducted using a derated 30 cm ion thruster with high-perveance design two-grid ion optics with xenon propellent. Lifetime projections were made based on a simple analysis of critical component erosion rates, and it was found that a strong correlation exists with the ratio of the specific impulse-to-input power. Under all operating conditions for which the projected thruster lifetime is less than 10,000 hrs, the life-limiting component of this technology is erosion of the accelerator grid due to charge-exchange ions. The use of alternative grid materials such as carbon is estimated to increase useful thruster lifetimes by as much as an order of magnitude and may enable long-life high thrust-density, sub-2500 s Isp operation. The performance and life of the derated thruster appears similar to that of the Russian SPT-100 thruster in the 1.0-2.0 kW, 1600-2000 s operational envelope.

Patterson, Michael J.↗

NASA NTRS1992

Low-Isp derated ion thruster operation

The performance and lifetime expectations of 30 cm xenon ion thruster technology at low values of specific impulse were evaluated, with emphasis on 1000-2500 s operation. Power levels of up to 2.0 kW, appropriate for auxiliary and orbit maneuvering propulsion, were processed at thrust-to-power ratios up to 57 mN/kW. These tests were conducted using a derated 30 cm ion thruster with high-perveance design two-grid ion optics with xenon propellant. Lifetime projections were made based on a simple analysis of critical component erosion rates, and it was found that a strong correlation exists with the ratio of the specific impulse-to-input power. Under all operating conditions for which the projected thruster lifetime is less than 10,000 hrs, the life-limiting component of this technology is erosion of the accelerator grid due to charge-exchange ions. The use of alternative grid materials such as carbon is estimated to increase useful thruster lifetimes by as much as an order of magnitude and may enable long-life high thrust-density, sub-2500 s Isp operation. The performance and life of the derated thruster appears similar to that of the Russian SPT-100 thruster in the 1.0-2.0 kW, 1600-2000 s operational envelope.

Patterson, Michael J.↗

NASA NTRS2012

Advanced Concepts: Aneutronic Fusion Power and Propulsion

Aneutronic Fusion for In-Space thrust, power. Clean energy & potential nuclear gains. Fusion plant concepts, potential to use advanced fuels. Methods to harness ionic momentum for high Isp thrust plus direct power conversion into electricity will be presented.

Chapman, John J.↗

NASA NTRS1990

Cyclic hot firing results of tungsten-wire-reinforced, copper-lined thrust chambers

An advanced thrust liner material for potential long life reusable rocket engines is described. This liner material was produced with the intent of improving the reusable life of high pressure thrust chambers by strengthening the chamber in the hoop direction, thus avoiding the longitudinal cracking due to low cycle fatigue that is observed in conventional homogeneous copper chambers, but yet not reducing the high thermal conductivity that is essential when operating with high heat fluxes. The liner material produced was a tungsten wire reinforced copper composite. Incorporating this composite into two hydrogen-oxygen test rocket chambers was done so that its performance as a reusable liner material could be evaluated. Testing results showed that both chambers failed prematurely, but the crack sites were perpendicular to the normal direction of cracking indicating a degree of success in containing the tremendous thermal strain associated with high temperature rocket engines. The failures, in all cases, were associated with drilled instrumentation ports and no other damages or deformations were found elsewhere in the composite liners.

Kazaroff, John M.↗

NASA NTRS2008

Chasing a Comet with a Solar Sail

Solar sail propulsion systems enable a wide range of missions that require constant thrust or high delta-V over long mission times. One particularly challenging mission type is a comet rendezvous mission. This paper presents optimal low-thrust trajectory designs for a range of sailcraft performance metrics and mission transit times that enables a comet rendezvous mission. These optimal trajectory results provide a trade space which can be parameterized in terms of mission duration and sailcraft performance parameters such that a design space for a small satellite comet chaser mission is identified. These results show that a feasible space exists for a small satellite to perform a comet chaser mission in a reasonable mission time.

Stough, Robert W.↗

NASA NTRSDate not supplied

Lightweight Thrust Chamber Composite Overwrap Lessons Learned

Filament winding a polymer/carbon fiber composite overwrap onto an additively manufactured copper combustion chamber will allow it to act as a light-weight structural jacket, significantly reducing weight for high pressure thrust chamber assemblies and reducing overall cost and fabrication schedules. Chamber assemblies for 2k lb. and 7k lb. of thrust have been successfully tested at NASA’s Marshall Space Flight Center. Multiple lessons were learned throughout the overwrap process development and manufacturing trials. The lessons learned on small scale hardware will guide further composite manufacturing technologies and enable a progression to larger scale assemblies with greater structural loads. Material performance requirements, manufacturing process development, and surface preparation were evaluated during the small chamber trials, with the broad thermal requirements of the resin being the primary driver for material selection and processing. Both epoxy and bismaleimide materials were evaluated with respect to both performance in the hot-fire test and ease of fabrication. Separately, surface preparation procedures were studied with the goal of providing a smooth chamber surface to promote a non-bonded overwrap. The recent testing of the 7k trust chamber has provided data in Non-Destructive Evaluation (NDE) and processing in order to continue to evaluate the performance requirements stated.

composite overwrap↗

NASA NTRS1984

Oxygen-hydrogen thrusters for Space Station auxiliary propulsion systems

The feasibility and technology requirements of a low-thrust, high-performance, long-life, gaseous oxygen (GO2)/gaseous hydrogen (GH2) thruster were examined. Candidate engine concepts for auxiliary propulsion systems for space station applications were identified. The low-thrust engine (5 to 100 lb sub f) requires significant departure from current applications of oxygen/hydrogen propulsion technology. Selection of the thrust chamber material and cooling method needed or long life poses a major challenge. The use of a chamber material requiring a minimum amount of cooling or the incorporation of regenerative cooling were the only choices available with the potential of achieving very high performance. The design selection for the injector/igniter, the design and fabrication of a regeneratively cooled copper chamber, and the design of a high-temperature rhenium chamber were documented and the performance and heat transfer results obtained from the test program conducted at JPL using the above engine components presented. Approximately 115 engine firings were conducted in the JPL vacuum test facility, using 100:1 expansion ratio nozzles. Engine mixture ratio and fuel-film cooling percentages were parametrically investigated for each test configuration.

Berkman, D. K.↗

NASA NTRS2004

The NASA GSFC MEMS Colloidal Thruster

A number of upcoming missions require different thrust levels on the same spacecraft. A highly scaleable and efficient propulsion system would allow substantial mass savings. One type of thruster that can throttle from high to low thrust while maintaining a high specific impulse is a Micro-Electro-Mechanical System (MEMS) colloidal thruster. The NASA GSFC MEMS colloidal thruster has solved the problem of electrical breakdown to permit the integration of the electrode on top of the emitter by a novel MEMS fabrication technique. Devices have been successfully fabricated and the insulation properties have been tested to show they can support the required electric field. A computational finite element model was created and used to verify the voltage required to successfully operate the thruster. An experimental setup has been prepared to test the devices with both optical and Time-Of-Flight diagnostics.

Cardiff, Eric H.↗

NASA NTRSDate not supplied

NASA's Composite Overwrap Lessons Learned on 40k Thrust Chamber Assemblies

Filament wound carbon fiber/polymer composite overwraps combined with additively manufactured (AM) copper alloy combustion chambers are a critical part of NASA’s Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project. The composite overwrap is a high strength-to-weight material and allows for significant weight reduction of the high-pressure thrust chamber assembly, reduction of overall cost, and reduced fabrication time while offering structural robustness. Integrated AM/composite overwrap chamber assemblies using 2,000 lbf (2k) and 7,000 lbf (7k) thrust were successfully hot fire tested at NASA Marshall Space Flight Center (MSFC). These assemblies allowed the team to learn lessons related to the design, analysis, and manufacturing of these integrated assemblies. A final goal of the RAMPT project is to design and test a 40,000 lbf (40k) thrust chamber assembly. The40k chamber presented the team several new challenges including an integral inlet port in the main body of the composite overwrap. Through multiple iterations of manufacturing techniques, varied materials, and Non-Destructive Evaluations (NDE), many lessons were learned to obtain a final design solution that would not only allow for the interrupted port inlet but also allow for sufficient material margins for the most critically stressed part of the chamber. This paper will cover the manufacturing techniques exploring fabric designs to help subsidize the coverage in the areas left bare by the inlet port during the filament winding process and custom tooling needed for the final full chamber processing. The original material choice of bismaleimide (BMI) 5250-4 from the 7k chamber performed well for the extreme environment of hot fire testing but proved to be difficult with the increased scale and interrupted port design of the 40kchamber. Discussion in this paper will cover these changes, including evaluation of the design, comparison to the prior 2k and 7k designs, and show the final hardware that will be tested. One primary goal of this work and RAMPT project is to provide this development process and data to industry for infusion into future engine designs.

Filament Wound↗

NASA NTRS1991

Full-scale investigation of aerodynamic interactions between a rotor and fuselage

A wind tunnel program has been conducted in the NASA Ames National Full-Scale Aerodynamics Complex to investigate the aerodynamic interactions between a full-scale helicopter main rotor and simple fuselage. This program provides the first complete, quantitative data base detailing the effects of a rotor on a full-scale fuselage. Steady fuselage and rotor loads were obtained as well as steady and unsteady fuselage pressures. Data were acquired over a range of rotor thrusts, advance ratios, and shaft tilts. As expected, results indicate that the largest effects on mean fuselage forces, moments, and surface pressures occur at low speeds and high rotor thrusts. Quantitative comparisons were made to determine the ability of small-scale tests to simulate the effect of the rotor on mean fuselage forces and pressures.

Norman, Thomas R.↗