Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYPERSONIC BOUNDARY LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Numerical simulation of crossing/turbulent boundary layer interaction at Mach 8.3 comparison of zero and two-equation turbulence models

A 3D hypersonic crossing shock wave/turbulent boundary layer interaction is examined numerically. The test geometry consists of a pair of opposing sharp fins of angle alpha = 15 deg mounted on a flat plate. The freestream Mach number is 8.28. Two theoretical models are evaluated. The full 3D Reynolds-averaged Navier-Stokes equations are solved using the Baldwin-Lomax algebraic turbulent eddy viscosity model and the Rodi turbulence model. Computed results for both cases show good agreement with experiment for flat plate surface pressure and for pitot pressure and yaw angle profiles in the flowfield. General agreement is obtained for surface flow direction. Fair to poor agreement is obtained for surface heat transfer, indicating a need for more accurate turbulence models. The overall flowfield structure is similar to that observed in previous crossing shock interaction studies.

Narayanswami, N.↗
NASA NTRS1971

A study of boundary layer transition on outgassing cones in hypersonic flow

Surface heat-transfer rates and pressures were measured at hypersonic speeds on sharp cones at zero angle of attack with and without gas injection. Using the non-injection results for reference data the effects on heating and transition location of surface roughness and injectant rate, distribution and composition were determined. The transition location was sensitive to the injectant distribution. The transition Reynolds numbers were significantly greater when the injectant distribution was constant than with a variable distribution. The measured heat-transfer distribution were also strongly dependent upon the injectant distribution. Transition Reynolds number results obtained during this program with a variable injectant distribution were correlated with a limited amount of data available for a degrading model tested in a different facility. Transitional data with constant injectant distribution were correlated with earlier results. An empirical correlation of heat-transfer reduction due to gas injection in turbulent flow was developed for both distributions tested. Several effects of mass addition on heating and transition, which have been earlier reported, were observed.

Stalmach, C. J., Jr.↗
NASA NTRS1972

Pressure-gradient effects on hypersonic turbulent skin friction and boundary-layer profiles.

Local skin friction, total-temperature profiles, and pitot-pressure profiles were measured on the wall of a Mach-7.4 wind tunnel. The wall to adiabatic wall temperature ratio was varied from 0.3 to 0.5. Boundary-layer characteristics were compared with those predicted by a finite-difference method. Local skin friction was predicted to within 15%. Pressure-gradient effects on the temperature and Mach number distributions and the shape factor (displacement thickness/momentum thickness) were underpredicted, but the velocity distributions were closely predicted.

Hopkins, E. J.↗
NASA NTRS1993

Aerodynamic heating in the vicinity of hypersonic, axisymmetric, shock-wave boundary-layer interactions

Aerodynamic heating rates are calculated from time-dependent temperature measurements in the vicinity of shock-wave boundary-layer interactions due to conical compression ramps on an axisymmetric body. The data were acquired at the Ohio State University Aeronautical and Astronautical Research Laboratory and at the Air Force Flight Dynamics Laboratory at Mach numbers of 6 and 10. The model is a cylindrical body with a 10 deg conical nose. Conical ramps with half-angles of 10, 20, 25, 30, and 35 deg serve as shock-wave generators. Flowfield surveys are made in the vicinity of the ramp vertices, separation points, and reattachment points. Experimental results quantify temperature response and the resulting heat transfer rates as a function of ramp angle, Reynolds number and freestream Mach number. The temperature responses within the flowfield appear to be steady-state for all angles and all Reynolds numbers, and hence, the heat transfer rates appear to be steady-state.

Flanagan, M. J., Jr.↗
DOE OSTI2024

Data-driven closure modeling for hypersonic turbulent flows

The Reynolds-averaged Navier–Stokes (RANS) equations remain a workhorse technology for simulating compressible fluid flows of practical interest. Due to model-form errors, however, RANS models can yield erroneous predictions that preclude their use on mission-critical problems. This report summarizes work performed from FY22-FY24 focused on improving RANS models for hypersonic flows using data-driven modeling and scientific machine learning. In this work we: 1. Investigate the current capabilities of RANS models in Sandia’s parallel aerodynamics and re-entry code (SPARC) for hypersonic flows with a focus on shock boundary layer interactions (SBLIs), 2. Assess several established corrections that exist in the literature aimed at improving predictions for SBLIs, 3. Develop improved models for the Reynolds stress tensor using tensor-basis neural networks, 4. Develop a neural-network-based variable turbulent Prandtl number model to reduce errors in wall heating in SBLIs. 5. Begin future investigations including employing the LIFE framework to improve wall heating predictions in SBLIs as well as the ensemble Kalman filter. We find that current RANS models in SPARC are deficient for complex SBLI flows. In particular, no current model jointly predicts wall heat flux, wall shear stress, and wall pressure with reasonable accuracy. Existing corrections help, but do not alleviate this issue altogether. The development of improved models for the Reynolds stress tensor via tensor-basis neural networks results in more predictive RANS models across a suite of low-speed and high-speed cases. For hypersonic boundary layers, the inclusion of the wall-normal Reynolds stress via TBNNs has an appreciable impact on the wall-normal momentum balance and wall quantities. However, we find that improvements to the Reynolds stress tensor do not address the over-prediction in wall heat flux in SBLIs. We find that a neural-network-based variable turbulent Prandtl number model systematically and substantially improves wall heating predictions for a range of SBLI cases.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1981

Force and moment, flow-visualization, and boundary-layer tests on a shuttle orbiter model at Mach 6

Force and moment, flow visualization, and boundary layer state tests were conducted using two 0.004 scale shuttle orbiter models. The force and moment tests were conducted for an angle of attack range from 20 to 40 deg and for Reynolds numbers based on reference length from 0.4 million to 3.6 million. Schlieren photographs were obtained for each angle of attack and Reynolds number. The boundary layer state tests, which were conducted using hot film sensors mounted in a separate model, were conducted over the same range of conditions as the force tests. Test results were combined to show that changes in the boundary layer on a typical hypersonic force test model affect measurement of the axial force coefficient and that the state of the local boundary layer is important for interpreting hypersonic aerodynamic test results.

Calloway, R. L.↗
NASA NTRS2011

Assessing Uncertainties in Boundary Layer Transition Predictions for HIFiRE-1 at Non-zero Angles of Attack

Boundary layer stability was analyzed for the HIFiRE-1 flight vehicle geometry for ground tests conducted at the CUBRC LENS I hypersonic shock test facility and the Langley Research Center (LaRC) 20- inch Mach 6 Tunnel. Boundary layer stability results were compared to transition onset location obtained from discrete heat transfer measurements from thin film gauges during the CUBRC test and spatially continuous heat transfer measurements from thermal phosphor paint data during the LaRC test. The focus of this analysis was on conditions at non-zero angles of attack as stability analysis has already been performed at zero degrees angle of attack. Also, the transition onset data obtained during flight testing was at nonzero angles of attack, so this analysis could be expanded in the future to include the results of the flight test data. Stability analysis was performed using the 2D parabolized stability software suite STABL (Stability and Transition Analysis for Hypersonic Boundary Layers) developed at the University of Minnesota and the mean flow solutions were computed using the DPLR finite volume Navier-Stokes computational fluid dynamics (CFD) solver. A center line slice of the 3D mean flow solution was used for the stability analysis to incorporate the angle of attack effects while still taking advantage of the 2D STABL software suite. The N-factors at transition onset and the value of Re(sub theta)/M(sub e), commonly used to predict boundary layer transition onset, were compared for all conditions analyzed. Ground test data was analyzed at Mach 7.2 and Mach 6.0 and angles of attack of 1deg, 3deg and 5deg. At these conditions, the flow was found to be second mode dominant for the HIFiRE-1 slender cone geometry. On the leeward side of the vehicle, a strong trend of transition onset location with angle of attack was observed as the boundary layer on the leeward side of the vehicle developed inflection points at streamwise positions on the vehicle that correlated to angle of attack. Inflection points are a strong instability mechanism that lead to rapid breakdown and transition to turbulence. The transition onset location on the windward side of the vehicle displayed no trend with angle of attack or freestream Reynolds number and transition was observed farther down the vehicle than observed on the leeward side of the vehicle. In analysis of both windward and leeward sides of the vehicle, use of the N factor methodology to develop trends to predict boundary layer transition onset showed improvements over the Re(sub theta)/M(sub e) empirical correlation methodology. Stronger correlations and less scatter in the data were observed when using the N factor method for these cases.

Marek, Lindsay C.↗
NASA NTRS1972

Cone transitional boundary-layer structure at Me = 14.

Experimental results suggest that the boundary-layer mean profiles in hypersonic flows may be highly transitional in the outer part of the boundary layer before the transition process is detected at the surface. Means of determining the initial location where the transition process begins in the outer part of the boundary layer are considered.

Fischer, M. C.↗
DOE OSTI2026

Boundary-layer receptivity to oblique freestream vorticity waves for a high-enthalpy hypersonic flow

The receptivity of a Mach 15 straight-cone boundary layer to oblique freestream vorticity waves is investigated using direct numerical simulation (DNS) alongside linear stability theory and the linear parabolized stability equations. A thermochemical nonequilibrium gas model is used. Oblique freestream vorticity waves at frequencies of 400, 800, and 1200 kHz are considered, with incident angles ranging from 0° to 29.4° at 400 kHz, 0° to 15.7° at 800 kHz, and 0° to 20.6° at 1200 kHz. The 400 kHz case is of primary interest due to the strong second-mode amplification at this frequency. Although the underlying base flow is axisymmetric, the oblique vorticity waves lead to a fully three-dimensional boundary-layer disturbance whose characteristics vary depending on the azimuthal ray relative to the freestream wave. Moving downstream within the second-mode instability region, some clear trends emerge in terms of the boundary-layer disturbance amplitudes; that is, disturbance amplitudes are highest at the leeward ray (relative to the freestream wave), but weakest about halfway between the windward and leeward rays. Increasing the incident angle causes the amplitudes to increase on the leeward ray and decrease on the windward ray. Moreover, the boundary-layer disturbance throughout contains a wide spectrum of azimuthal wavenumbers in which the disturbance energy falls off at higher wavenumbers. Increasing the incident angle causes the azimuthal spectrum of the boundary-layer disturbance to broaden overall. Qualitatively similar results are found for the two higher frequencies leading up to the peak-amplitude locations corresponding to the second-mode instability.

42 ENGINEERING↗
NASA NTRS2011

The lagRST Model: A Turbulence Model for Non-Equilibrium Flows

This study presents a new class of turbulence model designed for wall bounded, high Reynolds number flows with separation. The model addresses deficiencies seen in the modeling of nonequilibrium turbulent flows. These flows generally have variable adverse pressure gradients which cause the turbulent quantities to react at a finite rate to changes in the mean flow quantities. This "lag" in the response of the turbulent quantities can t be modeled by most standard turbulence models, which are designed to model equilibrium turbulent boundary layers. The model presented uses a standard 2-equation model as the baseline for turbulent equilibrium calculations, but adds transport equations to account directly for non-equilibrium effects in the Reynolds Stress Tensor (RST) that are seen in large pressure gradients involving shock waves and separation. Comparisons are made to several standard turbulence modeling validation cases, including an incompressible boundary layer (both neutral and adverse pressure gradients), an incompressible mixing layer and a transonic bump flow. In addition, a hypersonic Shock Wave Turbulent Boundary Layer Interaction with separation is assessed along with a transonic capsule flow. Results show a substantial improvement over the baseline models for transonic separated flows. The results are mixed for the SWTBLI flows assessed. Separation predictions are not as good as the baseline models, but the over prediction of the peak heat flux downstream of the reattachment shock that plagues many models is reduced.

Lillard, Randolph P.↗
NASA NTRS1972

A survey of NASA Langley studies on high-speed transition and the quiet tunnel

A quantitative experimental and theoretical assessment of the role of wind-tunnel disturbances in the boundary-layer transition process at hypersonic speeds is presented. The various approaches and recent results for the development of a low-noise-level tunnel are presented. A statistical parametric study of transition data with a large computer is shown for cones in free flight, ballistic ranges, and wind tunnels at essentially zero angle of attack. New transition results for slender cones at small angle of attack are also given, as are studies of transition at high angle of attack, which are compared with various correlation attempts. Included are results which indicate that hypersonic transition in the outer part of the boundary layer precedes the manifestation of transition at the wall.

Beckwith, I. E.↗
NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗
NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗
NASA NTRS2018

Characterization of Freestream Disturbances in Conventional Hypersonic Wind Tunnels

While low disturbance ("quiet") hypersonic wind tunnels are believed to provide more reliable extrapolation of boundary layer transition behavior from ground to flight, the presently available quiet facilities are limited to Mach 6, moderate Reynolds numbers, low freestream enthalpy, and subscale models. As a result, only conventional ("noisy") wind tunnels can reproduce both Reynolds numbers and enthalpies of hypersonic flight configurations, and must therefore be used for flight vehicle test and evaluation involving high Mach number, high enthalpy, and larger models. This article outlines the recent progress and achievements in the characterization of tunnel noise that have resulted from the coordinated effort within the AVT-240 specialists group on hypersonic boundary layer transition prediction. New Direct Numerical Simulation (DNS) datasets elucidate the physics of noise generation inside the turbulent nozzle wall boundary layer, characterize the spatiotemporal structure of the freestream noise, and account for the propagation and transfer of the freestream disturbances to a pitot-mounted sensor. The new experimental measurements cover a range of conventional wind tunnels with different sizes and Mach numbers from 6 to 14 and extend the database of freestream fluctuations within the spectral range of boundary layer instability waves over commonly tested models. Prospects for applying the computational and measurement datasets for developing mechanism-based transition prediction models are discussed.

Duan, Lian↗
NASA NTRS2016

Flight Experiment Verification of Shuttle Boundary Layer Transition Prediction Tool

Boundary layer transition at hypersonic conditions is critical to the design of future high-speed aircraft and spacecraft. Accurate methods to predict transition would directly impact the aerothermodynamic environments used to size a hypersonic vehicle's thermal protection system. A transition prediction tool, based on wind tunnel derived discrete roughness correlations, was developed and implemented for the Space Shuttle return-to-flight program. This tool was also used to design a boundary layer transition flight experiment in order to assess correlation uncertainties, particularly with regard to high Mach-number transition and tunnel-to-flight scaling. A review is provided of the results obtained from the flight experiment in order to evaluate the transition prediction tool implemented for the Shuttle program.

Berry, Scott A.↗
NASA NTRS1973

Control of supersonic wind-tunnel noise by laminarization of nozzle-wall boundary layer

One of the principal design requirements for a quiet supersonic or hypersonic wind tunnel is to maintain laminar boundary layers on the nozzle walls and thereby reduce disturbance levels in the test flow. The conditions and apparent reasons for laminar boundary layers which have been observed during previous investigations on the walls of several nozzles for exit Mach numbers from 2 to 20 are reviewed. Based on these results, an analysis and an assessment of nozzle design requirements for laminar boundary layers including low Reynolds numbers, high acceleration, suction slots, wall temperature control, wall roughness, and area suction are presented.

Beckwith, I. E.↗