Search NASA⌕ Search

SEARCH · Search NASA

Results for “Homogenization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Unveiling the Role of In Situ Al 2 O 3 Passivation in Molecular-Ink-Processed CuIn(S,Se) 2 Photovoltaics

Here, we report on the optimization of in situ passivation of ink-based CuIn(S,Se) 2 thin-film solar cells via controlled incorporation of Al 2 O 3 in CuIn(S,Se) 2 films by the addition of Al(NO 3 ) 3 to the molecular ink precursor. For this purpose, the Al/(Al + In) (AAI) metal ratio was varied from 0.05 to 0.30. We observe that the efficiency of the cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 is consistently higher than those without Al 2 O 3 , especially due to an improvement in open-circuit voltage (V OC ) and fill factor (FF), for all tested AAI ratios. With an AAI of 0.05, a maximum efficiency of 11.2% and an average efficiency of 8.5% (measured across 18 cells) was achieved, compared to 8.5% maximum efficiency and 6.5% average efficiency for Al-free CuIn(S,Se) 2 . Furthermore, we find that cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 with an AAI of 0.2 show a narrow distribution in the photovoltaic performance, indicating higher reproducibility and higher FF. Energy-dispersive X-ray spectroscopy shows that, at AAI = 0.2, Al 2 O 3 is distributed more homogeneously at the surface of the Al 2 O 3 -incorporated CISSe. Capacitance-voltage measurements reveal a reduced defect density by incorporation of Al 2 O 3 , which could be partly responsible for the higher V OC . Furthermore, using detailed surface analysis with various X-ray and electron spectroscopy methods, we derive chemical and electronic structure information from the surface. With ultraviolet photoelectron (UPS) and inverse photoemission spectroscopies (IPES), the electronic band gap of the CuIn(S,Se) 2 thin-film surface is found to increase from 1.22 to 1.88 eV (+-0.12 eV) with Al 2 O 3 incorporation. This is accompanied by a clear reduction of the conduction band spike at the CdS/CISSe interface due to Al 2 O 3 addition, as derived by both UPS and IPES as well as temperature-dependent V OC measurements.

14 SOLAR ENERGY↗
DOE OSTI2026

Electrode Modification by Laser Ablation to Overcome Mechanical and Scalability Limitations of Solid-State Prealkylation of Electrode Architectures

In this work, laser ablation of Si electrode surfaces is utilized to provide localized strain relief during the Solid State Prealkylation of Electrode Architectures (SPEAR) process, in addition to volumetric expansion relief in the form of free volume channels across the electrode. A hexagonal mesh patterning was employed via laser ablation, where the hexagonal diameter (pitch) was varied from 250 to 1000 µm. It was demonstrated that these channels serve as expansion voids, accommodating the increase in electrode thickness observed during SPEAR and preventing cracking at the electrode surface. Optical microscopy and Raman mapping confirm that Li diffusion is the rate-limiting solid-state process, requiring a 24 h rest period to achieve homogeneous LixSi alloying through the electrode bulk. Electrochemical evaluations in full cells show that a 1000 μm pitch pattern yields a high initial discharge capacity of 2485 mA h g–1 and 86.4% capacity retention after 80 cycles, whereas smaller pitches (<500 μm) result in lithium plating at 4.1 V in full cells paired with NMC 811 due to excessive current collector exposure from the ablation process. XPS analysis reveals that the laser treatment modifies the electrode surface by increasing the Si–O and C–O species, changing the SEI composition observed via an increase in fluorophosphates upon cycling.

Musgrove, Amanda [ORNL] (ORCID:0009000220910389)↗
DOE OSTI2024

Binary Cation Matrix Electrolyte and Its Effect on Solid Electrolyte Interphase Suppression and Evolution of Si Anode

An unstable solid electrolyte interphase (SEI) has been recognized as one of the biggest challenges to commercializing silicon (Si) anodes for high-energy-density batteries. This work thoroughly investigates a binary cation matrix of Mg 2+ +Li + electrolyte and its role in SEI development, suppression, and evolution of a Si anode. Findings demonstrate that introducing Mg ions dramatically reduces the SEI growth before lithiation occurs, primarily due to the suppression of solvent reduction, particularly ethylene carbonate (EC) reduction. The Mg 2+ alters the Li + cation solvation environment as EC preferably participates in the oxophyllic Mg 2+ solvation sheath, thereby altering the solvent reduction process, resulting in a distinct SEI formation mechanism. The initial SEI formation before lithiation is reduced by 70% in the electrolyte with the presence of Mg 2+ cations. While the SEI continues to develop in the postlithiation, the inclusion of Mg ions results in an approximately 80% reduction in the postlithiation SEI growth. Continuous electrochemical cycling reveals that Mg 2+ plays a crucial role in stabilizing the deep-lithiated Si phases, which effectively mitigates side reactions, resulting in controlled SEI growth and stable interphase while eliminating complex Li x Si y formation. Mg ions promote the development of a notably more rigid and homogeneous SEI, characterized by a reduced dissipation (ΔD) in the Mg 2+ +Li + ion matrix compared to the solely Li + system. In conclusion, this report reveals how the Mg 2+ +Li + ion matrix affects the SEI evolution, viscoelastic properties, and electrochemical behavior at the Si interface in real time, laying the groundwork for devising strategies to enhance the performance and longevity of Si-based next-generation battery systems.

25 ENERGY STORAGE↗
DOE OSTI2025

Supported-Single Nickel Atom Catalysts for the Methanation of Carbon Dioxide

Synthesis of twenty-seven bimetallic catalysts consisting of nickel and one of nine different dopants (B, Co, Cu, Fe, Mg, Mn, Sn, V, and Zn) supported on three different metal oxides (Al 2 O 3 , CeO 2 , and SiO 2 ) is carried out via organometallic grafting. The catalysts are evaluated for their activity and selectivity for the CO 2 methanation reaction at a feed ratio of H 2 /CO 2 of 4 at 300 °C in a high-throughput flow reactor system. After in situ pre-activation (500 °C in H 2 ), Ni/Co/CeO 2 exhibited high conversion (84.3%) and selectivity for methane (99.6%). Ni/Co/CeO 2 was characterized by high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction, H 2 -temperature-programmed reduction (H 2 -TPR), and CO 2 -temperature-programmed desorption (CO 2 -TPD). HRTEM showed the presence of single Ni and Co atoms on ceria after pre-reduction at 500 °C and after the methanation reaction at 300 °C for 15 h. XPS determined that the strong interaction between Ni, Co, and ceria increased after the reduction, leading to a charge transfer between Ni and Ce that created oxygen vacancies in ceria. Nickel was found to be Ni 2+ in the as-prepared material and was partially reduced in the presence of cobalt and after the activation in H 2 at 500 °C. The DFT results show that both nickel and cerium exhibit lower Bader charges in the Ni/Co/CeO 2 system, confirming that the presence of cobalt enhances the reduction of both Ni and Ce through electronic interactions. This indicates that single cationic Ni atoms are highly effective for the methanation reaction. In conclusion, the organometallic grafting technique is found to be efficient for synthesizing catalysts with highly homogeneous dispersed species at low metal loadings (0.16 wt % Ni–0.15 wt % Co), which leads to high turnover frequency (up to 248.7 h –1 ) and durability for methanation.

CO2 conversion↗
DOE OSTI2025

Effect of Networking Density on the Patterning Performance of Molecular Layer Deposited Alucone Electron Beam/EUV Resists

One of the main barriers to continued device scaling in the era of extreme ultraviolet (EUV) lithography is the need for improved photoresist chemistries to address challenges such as poor EUV sensitivity, inadequate etch resistance, and pattern collapse. Metal-organic photoresists are a promising class of materials that can address many of these challenges, and among them, resists deposited via hybrid molecular layer deposition (MLD) have attracted interest for their unique advantages in thickness control, chemical homogeneity, and compatibility with vacuum processing. However, despite many successful demonstrations of patterning, little is known about how the molecular design of hybrid MLD resists affects their lithographic performance. In this work, we study the effect of the network structure, a common feature among all hybrid MLD resists, via a series of aluminum alkoxide ("alucone") negative tone resists with varying networking density. Their patterning mechanism is investigated via electron beam lithography (EBL)─a common proxy for EUV─and compared to their EUV-induced reactions studied via flood exposure and in situ characterization. In conclusion, we show that the resist with the least networking density demonstrates the best sensitivity and resolution, with the ability to resolve dense line/space gratings as small as 14 nm half pitch via EBL.

electron beam lithography↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗
DOE OSTI2026

Designing the Platinum Catalyst Layer for Improved Performance and Durability in Anion Exchange Membrane Water Electrolysis

To lower the cost of hydrogen produced by anion exchange membrane water electrolysis (AEMWE), it is critical to reduce the use of platinum group metal (PGM) catalysts within the device. While iridium has been successfully replaced with PGM-free catalysts at the anode, platinum-based (Pt) cathode catalysts are still required to meet the activity and durability targets. This study investigates the impact of commercial Pt/C catalyst loading, ionomer type and content, and electrode fabrication method on the cathode catalyst layer properties and AEMWE performance with the aim of determining the feasibility of reduced Pt loadings. While increased Pt loading is found to improve beginning-of-life performance, the effects are minimal above 0.6 mg/cm 2 . Ink characterization shows that ionomer type and content affect the ink stability, particle size, and percent of unbound ionomer, which further impact the homogeneity of the sprayed catalyst layers. The 5% PiperION cathode exhibited the highest performance, which may be attributed to a balance between the small particle size and the low proportion of unbound ionomer, minimizing kinetic and transport losses. Theoretical calculations show that the ionomers interact differently with the Pt surface, causing different surface charges and water adsorption strength and activating different mechanisms for hydrogen evolution. Pt-PiperION lowered the enthalpy of water-splitting by 0.1 eV compared to Pt alone and allowed for equal site access between adsorbed H* and OH* (both adsorbed at circa −2.2 eV). Although catalyst-coated membrane (CCM) fabrication techniques are desirable for scale-up, no performance enhancement is observed compared with the catalyst-coated substrate approach. Durability, as measured by degradation rates, Pt loss, and catalyst layer restructuring, was found to improve with increased Pt loadings, higher ionomer content, and CCM architectures. These findings provide important insight into the significant role of the cathode in AEMWE and strategies for maintaining the performance with low Pt loading or PGM-free catalysts.

08 HYDROGEN↗
DOE OSTI2026

Ultrafast Reactive Laser Sintering of Highly Conductive Garnet-Type LLZTO Solid Electrolytes

Rapid and scalable fabrication of garnet-type solid electrolytes remains a major challenge for the practical deployment of lithium metal batteries. Here, we report reactive laser sintering (RLS) as an ultrafast and potentially scalable strategy for fabricating garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolytes. RLS of LLZTO enables simultaneous reaction and densification, achieving ∼95% relative density while minimizing lithium loss and suppressing secondary phase formation. Compared to conventional furnace sintering, RLS promotes enhanced grain growth and improved densification, leading to improved ionic conductivity (0.36 ± 0.08 mS cm −1 ) while maintaining comparable activation energies for Li + transport. Structural characterization by X-ray diffraction (XRD), Raman spectroscopy, and solid-state 6 Li/ 7 Li NMR confirms the formation of cubic garnet LLZTO with homogeneous microscale elemental distribution. In addition, nanoindentation measurements demonstrate that RLS preserves the mechanical properties of the garnet framework despite ultrafast localized thermal processing. By integrating simultaneous reaction and densification with tunable microstructural control, reactive laser sintering provides a promising manufacturing pathway for high-performance garnet solid electrolytes toward next-generation solid-state batteries.

CO2 laser↗
DOE OSTI2024

In Situ TEM for Structural and Chemical Evolutions of Bimetallic Pt–Ni Nanoparticles at Elevated Temperatures: Implications for Heterogeneous Catalysis

Platinum-based bimetallic nanoparticles (NPs) are of great interest for their applications in catalysis. The catalytic properties of these NPs are significantly dependent on their morphology, structure, and composition, whose response to thermal input remains challenging to be fully understood. This study investigates the thermally induced structural and chemical evolutions of single-crystalline Pt-Ni NPs using in situ transmission electron microscopy. The observed morphological evolution includes the facet development from a truncated octahedron to a spherical-like isotropic shape, followed by the formation of pancake-like ellipsoid shape at high temperatures due to surface atom migration and interfacial wetting enabled by the particle-substrate interaction. Comparative investigations by in situ scanning transmission electron microscopy with energy dispersive X-ray spectroscopy mapping elucidate that the solid-solution compositional configuration can be retained over a large temperature range, while core-shell NPs undergo irreversible solid-solution transitions through chemical homogenization at elevated temperatures. Finally, these findings elucidate the effect of thermal input on structural evolution and compositional redistribution of Pt-Ni bimetallic NPs, offering valuable insights into the design of heterogeneous catalysts.

25 ENERGY STORAGE↗
DOE OSTI2024

Reactive Modified Epoxy Resin and Its Miscible Blends Based on Recycled Oligomers from Solvolysis

Chemical depolymerization of fully cured epoxy resin with 20% reactive modifier was successfully performed via a solvent-assisted solvolysis process into low molecular weight recyclable oligomers (RO) at 240 °C in a pressure vessel at 650 psi for 4 h. The thermoset epoxy resin was depolymerized into transparent brown viscous fluid with a higher viscosity than the uncured epoxy resin with approximately 93% yield. Different concentrations of the RO were homogeneously mixed with the pure epoxy resin, and their curing kinetics, viscosity, FTIR, mechanical properties, DMA, and cross-link density were investigated. The curing kinetics of the pure reactive modified epoxy resin (baseline) and its mixtures with RO of different concentrations were investigated under both isothermal and nonisothermal conditions using small amplitude oscillatory shear flow. The elastic and viscous moduli (G′ and G″), complex viscosity (η*), and tan δ values were evaluated at different curing times and temperatures. The G′, G″, and η* increased dramatically, while tan δ decreased strongly by several orders of magnitude at the gel point. The zero-shear viscosity (η 0 ) was determined from the angular frequency dependent on η* based on the Cross model for different blend compositions in the liquid state before curing. The composition dependence of η 0 showed a positive deviation from the linear mixing rule and was well described by the Lecyar model. Here, the apparent activation energy of curing (E a ) was also evaluated according to the Arrhenius equation and was found to be 46 ± 2 kJ/mol regardless of the different contents of RO. For all blends up to 40 wt % RO, only one tan δ peak systematically shifting to lower temperatures with increasing content of RO was observed in the DMA measurements, indicating that the epoxy resin and the RO are miscible with up to 40 wt % RO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

3D Printing of Polyelectrolyte Complex-Integrated Photocurable Hydrogel Resins

In this study, we developed a photocurable hydrogel resin incorporating a polyelectrolyte complex (PEC) for 3D printing. Acrylamide-based monomers were formulated with varying PEC contents (0–15 wt %) in an aqueous KBr medium to fabricate patterned porous hydrogel structures. The morphology of printed hydrogels was characterized by field-emission scanning electron microscopy and energy-dispersive X-ray spectroscopy. Notably, the PEC5 and PEC10 formulations exhibited optimal thermal stability and compressive properties, attributed to the homogeneous distribution of PEC domains within the hydrogel matrix. Furthermore, dye adsorption experiments demonstrated excellent removal efficiency, highlighting the potential of PEC-containing hydrogels for environmental remediation applications, particularly in the treatment of dye-contaminated wastewater.

Yang, Jinchul [University of Tennesse Knoxville]↗
DOE OSTI2026

Aluminum Based Solvent-Free Organic–Inorganic Hybrid Materials

In emerging materials, molecular hybrids are especially promising, as they have molecular level mixing of the organic and inorganic components, producing homogeneous materials without interfaces that can deteriorate properties. However, the current methods of manufacturing molecular hybrids are based on solution processing, which is impractical for bulk materials such as may be used for optically clear radiation and electromagnetic shielding components or photonics. Here we examine molecular hybrids composed of aluminum isopropoxide (AIP) and epoxy resins aiming to understand the molecular scale chemistry and manufacturability of these hybrid materials. DSCmonitored cure revealed the ideal cure temperature for these materials is 160−170 °C and demonstrated that an AIP concentration of 16.7 wt % maximizes the extent of reaction. Kinetic analysis of the curing reaction showed the Sestak−Berggren autocatalytic model is effective at temperatures over 140 °C but the reaction has diffusion limitations at a temperature of 120 °C. Mechanical testing with custom resin molds revealed a decrease in properties of the bulk samples with increasing AIP content due to an increase in defects but further testing with nanoindentation demonstrated comparable or improved mechanical properties of AIP-epoxy hybrids compared to epoxy resin with a standard hardener. Ultimately, this work lays the foundation for hardener-free epoxy-aluminum inorganic/organic hybrids and presents opportunities to expand on properties for specific applications such as thermal conductivity, optical clarity, and dielectric constant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Miscibility and Cocrystallization in Ethylene–Vinyl Alcohol Copolymer Blends

The compatibility among different ethylene−vinyl alcohol (EVOH) copolymer grades plays a crucial role in determining how easily they can be recycled when present together in a mixed waste stream. In this work, melt miscibility and cocrystallization in 50/50 wt/wt binary blends of EVOH copolymers with differing ethylene content were studied. Blends with up to a 21 mol % difference in composition were analyzed. Thin films of miscible blends appeared homogeneous in the melt as observed under an optical microscope, whereas AFM height images showed that immiscible blends underwent surface roughening due to phase separation. For copolymers with modest composition differences, the blend behaved as a single component, showing single, narrow melting and crystallization peaks in DSC thermograms, indicating cocrystallization at the level of crystal stems. Interestingly, even phase-separated blends demonstrated partial cocrystallization due to partial miscibility of the components in the molten phase-separated domains. The extent of cocrystallization is governed by the difference in freezing points of the components; rapid cooling increased cocrystallization in the blends. The maximum compositional difference allowed for miscibility is not constant but depends on the blend’s average comonomer content, in agreement with the “miscibility window” calculated from literature pressure−volume−temperature behavior for the individual EVOH copolymers and regular mixing theory. This study helps illuminate the effect of copolymer composition on miscibility, as well as cocrystallization behavior in blends of random copolymers with cocrystallizable units.

Cocrystallization↗
DOE OSTI2025

Evaluating the Origins of Aerobic Oxidation Catalysis with TAM-3, a MOF with Accessible Co(II) Sites and Large Pores

Metal-organic frameworks (MOFs) are attractive platforms that merge concepts of homogeneous and heterogeneous catalysis. Catalyst design and optimization are enabled by an array of synthetic methods that offer independent control over the local chemical structure of lattice-embedded metal ions (i.e., ligand identity and geometry) and the long-range materials properties (i.e., porosity). Establishing the origin of catalytic activity in MOF-promoted reactions remains a significant challenge: The relative rates of catalyst turnover and substrate diffusion dictate the extent to which interstitial sites are accessible and operational in catalysis. To minimize the contributions of surface sites in catalysis, materials with large pore dimensions are often sought, however, the impact of pore expansion on the origins of catalytic activity is similarly challenging to establish. Here, we describe TAM-3, a Co(II) based MOF with accessible metal sites supported by a facially coordinating tris-tetrazole ligand set. TAM-3 features large channel-like pores (17 × 23 Å) and promotes aerobic C−H oxidation and olefin epoxidation. Using a set of simple kinetics experiments, based on the analysis of kinetic isotope effects and olefin oxidation diastereoselectivities, we demonstrate that despite the large pores, interstitial metal ions do not significantly contribute to the observed substrate oxidation. This study highlights the importance of conducting kinetic experiments to assess the origin of apparent catalytic activity with MOFs and the challenge of harnessing reactive oxidants with microporous catalyst materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Effect of Strength of Soluble and Solid Acid Catalysts on Selectivity in Aldol Reactions

Aldol reactions can follow the classical condensation path and produce an α,β-unsaturated carbonyl compound and water, however in some cases, aldol chemistry may be steered towards a fission that gives an olefin and a carboxylic acid. This investigation examines how the strength of Brønsted acid sites—both in homogeneous and heterogeneous catalysis—controls these two pathways and their kinetics. The cross-aldol reaction between benzaldehyde and 3-pentanone served as test case. Batch reactions, conducted in toluene as solvent at a temperature of 140 °C under autogenous pressure, were analyzed by GC and in situ ATR-FTIR spectroscopy to determine product distributions and rate constants for condensation and fission pathways. A series of soluble acids including a family of sulfonic acids mostly favored the condensation pathway, with formic acid as the weakest in the series by its pKa being inactive for aldol chemistry. Significant amounts of fission products were rare except for the known selectivity of phosphoric acid, and the circumstances were difficult to delineate. For the sulfonic acid family, the logarithm of the first-order condensation rate constants scaled only roughly with pKa (water) values, whereas a good correlation was obtained with calculated deprotonation Gibbs energies in toluene. A series of H-forms of isomorphously substituted beta zeolites, HESiBEA with E = Al, Ga, Fe, or B, favored the fission pathway. Site density and site strength were characterized by calorimetric measurements of the heats of adsorption of isopropylamine, which decreased in the order Al > Ga, Fe > B. The logarithm of the site-normalized first-order fission rate constants scaled roughly with the heats of adsorption and correlated excellently with reported deprotonation energies. In conclusion, acid strength mainly affects activity and can be seen as a pre-requisite for either aldol condensation or fission chemistry, whereas additional, yet to be full clarified catalyst properties and reaction conditions are required to steer aldol chemistry towards fission selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Pore-Scale Transport Effects in Electrochemical CO 2 Reduction on Gold via Coupled Microkinetic-Transport Modeling

A pore-resolved modeling framework is developed to quantify how pore-scale transport affects the intrinsic microkinetics of CO 2 -to-CO on Au. A DFT-informed microkinetic model is coupled self-consistently to a Generalized-Modified Poisson–Nernst–Planck (GMPNP) transport description in a single, electrolyte-filled cylindrical pore, allowing local concentrations and potential to feed back into site-specific reaction rates. FIB-SEM is used to determine pore sizes within realistic electrode materials. Across pore diameters, d p = 10–6000 nm, the surface-averaged CO 2 reduction rate is systematically reduced relative to the ideal microkinetic baseline where mass transport is not accounted for; the effectiveness factor 𝜂 𝑠,CO 2 , which quantifies this ratio, decreases rapidly at more negative potentials and is about 1% near −1.0 V vs SHE due to reactant depletion. Spatial maps reveal pore-bulk alkalization that emerges at higher cathodic bias, with a small, near-wall pH dip due to electrostatic repulsion of hydroxide at the cathode interface. For a fixed aspect ratio L p /d p , narrower pores exhibit larger 𝜂 𝑠,CO 2 by shortening diffusion paths, whereas variations in the aspect ratio L p /d p play a secondary role. A dimensionless analysis (surface/bulk Damköhler numbers) delineates operating regimes. In conclusion, this work offers a concept for incorporating microkinetic models into homogenized porous-electrode models through effectiveness factors and pore-size distribution.

Au-catalyst↗
DOE OSTI2025

Molecular-level Regulation of PEO-Based Electrolytes with CaF 2 Nanoparticles for Advanced Solid-State Lithium Metal Batteries

The poly(ethylene oxide) (PEO)-based electrolyte has caught much attention for its flexibility, interfacial compatibility, and low cost, but the low ionic conductivity and poor mechanical strength severely hinder its further application in solid-state batteries. Herein, a molecular level regulation through adding CaF 2 nanoparticle fillers is proposed to enhance the electrochemical performance of the PEO-based electrolyte. The strong coordination effects of the Ca cation with a Li salt anion and ether-oxygen increase the dissociated Li ion concentration and accelerate Li ion migration, thus enhancing the ionic conductivity of the electrolyte when combined with their physical disruption in the PEO matrix (0.31 mS cm -1 at 55 °C). Moreover, the spontaneous reaction between Li and CaF 2 generates a LiF-rich solid electrolyte interphase, which promotes homogeneous Li deposition. Consequently, the PEO-CaF 2 electrolyte delivers symmetric cells over 6300 h and maintains full batteries over 1000 cycles with 80% capacity retention. In conclusion, the assembled pouch-cell displays robust performance, further demonstrating its potential practical application.

Li, Tao [Lanzhou Univ. (China)] (ORCID:00000003196↗
DOE OSTI2025

Investigating Particle Phase State Dependencies during a Historic Pacific Northwest Wildfire Event

The function and lifetime of an atmospheric particle are greatly dependent upon its phase state. Studying particle phase states from specific ambient source types is often challenging due to uncontrolled environmental conditions and multiple source contributions. However, a historic Pacific Northwest wildfire event occurred in September 2020, providing a rare opportunity to study a pseudo-single particle type ambient sample (i.e., wildfire) over time. Sampling was performed in Richland, Washington, capturing aged particles from shifting wildfire sources. In addition to source variability, temporal variation in wildfire particle phase state was observed from single particle analyses. Despite this, single particle elemental compositions were homogenous over time (=87% carbonaceous) with no significant temporal variation in organic functional group abundances within individual particles either (e.g., 4% relative standard deviation in alkene contributions). While particle composition is indeed known to affect phase state, water uptake appeared to be the most significant contributor to phase state variability amongst single particles here, as particle aspect ratios (related to phase state) linearly correlated with ambient relative humidity during sampling (R2 = 0.65). Therefore, while limited to a case study, meteorological considerations are found to convey greater comparative importance than particle composition for aged particle phase state predictions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗