Search NASA⌕ Search

SEARCH · Search NASA

Results for “LANDING SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Impact tests on fibrous composite sandwich structures

The effect of low velocity impact on the strength of laminates fabricated from graphite/epoxy and Kevlar 49/epoxy composite materials was studied. The test laminates were loaded statically either in uniaxial tension or compression when impact occurred to evaluate the effect of loading on the initiation of damage and/or failure. Typical aircraft service conditions such as runway debris encountered during landing were simulated by impacting 1.27-cm-diameter projectiles normal to the plane of the test laminates at velocities between 5.2 and 48.8 m/s.

Rhodes, M. D.↗
NASA NTRS1977

Airline pilot scanning behavior during approaches and landing in a Boeing 737 simulator

A series of approaches using airline-rated Boeing 737 pilots in an FAA qualified simulator has been conducted. The test matrices include both manual and coupled approaches for VFR, Category I and Category II conditions. A nonintrusive oculometer system was used to track the pilot's eye-point-of-regard throughout the approach. The results indicate that, in general, the pilots use a different scan technique for the manual and coupled (auto-pilot with manual throttle) conditions. For the manual approach 73 percent of the time was spent on the Flight Director and 13 percent on airspeed as opposed to 50 percent on Flight Director and 23 percent on airspeed for the coupled approaches. For the visual portion of approach from less than 100 m (300 ft) to touchdown or when the touchdown point came into view, the pilots tend to fixate on their aim or touchdown area until the flare initiation, at which time they let their eye-point-of-regard move up the runway to use the centerline lights for rollout guidance.

Spady, A. A., Jr.↗
NASA NTRS1981

Airframe noise of a small model transport aircraft and scaling effects

Airframe noise of a 0.01 scale model Boeing 747 wide-body transport was measured in the Langley Anechoic Noise Facility. The model geometry simulated the landing and cruise configurations. The model noise was found to be similar in noise characteristics to that possessed by a 0.03 scale model 747. The 0.01 scale model noise data scaled to within 3 dB of full scale data using the same scaling relationships as that used to scale the 0.03 scale model noise data. The model noise data are compared with full scale noise data, where the full scale data are calculated using the NASA aircraft noise prediction program.

Shearin, J. G.↗
NASA NTRS1983

Flexible Aircraft Takeoff and Landing Analysis

Flexible Aircraft Takeoff and Landing Analysis Program, FATOLA, simulates aircraft takeoff and landing dynamics. Program includes maneuver logic and autopilots for glide slope, flare, landing, and takeoff and is modular so performance of aircraft in flight and during landing and ground maneuvers can be studied separately or in combination.

Carden, H. D.↗
NASA NTRS1987

The ballistic Mars hopper - An alternative Mars mobility concept

The ballistic Mars hopper is proposed as an alternative mobility concept for unmanned exploration of the Martian surface. In the concept, oxygen and carbon monoxide produced from the Martian atmosphere are used as propellants in a rocket propulsion system for an unmanned vehicle on suborbital trajectories between landing sites separated by distances of up to 1000 km. This mobility concept is seen as uniquely capable of allowing both intensive and extensive exploration of the planet using only a single landed vehicle of mass approximately 2000 kg. The technical challenges associated with in-situ propellant production on the surface of Mars are reviewed. A rocket propulsion subsystem capable of using oxygen and carbon monoxide as propellants is described. Finally, results of mission analysis and a hopper landing hazard simulation are reported. It is concluded that an attractive Mars hopper can be developed based on relatively near-term technology.

Sercel, Joel C.↗
NASA NTRS1990

A strategy to study regional hydrology and terrestrial ecosystem processes using satellite remote sensing, ground-based data and computer modeling

A strategy is presented for integrating scanning multichannel microwave radiometer data from the Nimbus-7 satellite with meteorological station records and computer simulations of land surface hydrology, terrestrial nutrient cycling, and trace gas emission. Analysis of the observations together with radiative transfer analysis shows that in the tropics the temporal and spatial variations of the polarization difference are determined primarily by the structure and phenology of vegetation and seasonal inundations of major rivers and wetlands. It is concluded that the proposed surface hydrology model, along with climatological records, and, potentially, 37-GHz data for phenology, will provide inputs to a terrestrial ecosystem model that predicts regional net primary production and CO2 gas exchange.

Vorosmarty, C.↗
NASA NTRS1994

Sensitivity properties of a biosphere model based on BATS and a statistical-dynamical climate model

A biosphere model based on the Biosphere-Atmosphere Transfer Scheme (BATS) and the Saltzman-Vernekar (SV) statistical-dynamical climate model is developed. Some equations of BATS are adopted either intact or with modifications, some are conceptually modified, and still others are replaced with equations of the SV model. The model is designed so that it can be run independently as long as the parameters related to the physiology and physiognomy of the vegetation, the atmospheric conditions, solar radiation, and soil conditions are given. With this stand-alone biosphere model, a series of sensitivity investigations, particularly the model sensitivity to fractional area of vegetation cover, soil surface water availability, and solar radiation for different types of vegetation, were conducted as a first step. These numerical experiments indicate that the presence of a vegetation cover greatly enhances the exchanges of momentum, water vapor, and energy between the atmosphere and the surface of the earth. An interesting result is that a dense and thick vegetation cover tends to serve as an environment conditioner or, more specifically, a thermostat and a humidistat, since the soil surface temperature, foliage temperature, and temperature and vapor pressure of air within the foliage are practically insensitive to variation of soil surface water availability and even solar radiation within a wide range. An attempt is also made to simulate the gradual deterioration of environment accompanying gradual degradation of a tropical forest to grasslands. Comparison with field data shows that this model can realistically simulate the land surface processes involving biospheric variations.

Zhang, Taiping↗
NASA NTRS1960

An Examination of Handling Qualities Criteria for V/STOL Aircraft

A study has been undertaken to define hand-ling qualities criteria for V/STOL aircraft. With the current military requirements for helicopters and airplanes as a framework, modifications and additions were made for conversion to a preliminary set of V/STOL requirements using a broad background of flight experience and pilots' comments from VTOL and STOL aircraft, BLC (boundary-layer-control) equipped aircraft, variable stability aircraft, flight simulators and landing approach studies. The report contains a discussion of the reasoning behind and the sources of information leading to suggested requirements. The results of the study indicate that the majority of V/STOL requirements can be defined by modifications to the helicopter and/or airplane requirements by appropriate definition of reference speeds. Areas where a requirement is included but where the information is felt to be inadequate to establish a firm quantitative requirement include the following: Control power and damping relationships about all axes for various sizes and types of aircraft; control power, sensitivity, d-amping and response for height control; dynamic longitudinal and dynamic lateral- directional stability in the transition region, including emergency operation; hovering steadiness; acceleration and deceleration in transition; descent rates and flight-path angles in steep approaches, and thrust margin for approach.

Anderson, Seth B.↗
NASA NTRS1998

An Atmospheric Guidance Algorithm Testbed for the Mars Surveyor Program 2001 Orbiter and Lander

An Atmospheric Flight Team was formed by the Mars Surveyor Program '01 mission office to develop aerocapture and precision landing testbed simulations and candidate guidance algorithms. Three- and six-degree-of-freedom Mars atmospheric flight simulations have been developed for testing, evaluation, and analysis of candidate guidance algorithms for the Mars Surveyor Program 2001 Orbiter and Lander. These simulations are built around the Program to Optimize Simulated Trajectories. Subroutines were supplied by Atmospheric Flight Team members for modeling the Mars atmosphere, spacecraft control system, aeroshell aerodynamic characteristics, and other Mars 2001 mission specific models. This paper describes these models and their perturbations applied during Monte Carlo analyses to develop, test, and characterize candidate guidance algorithms.

Striepe, Scott A.↗
NASA NTRS1948

Ditching Tests of Two Models of the Army B-36 Airplane

The ditching characteristics of the Army B-36 airplane were determined by testing 1/20- and 1/30-scale dynamic models in calm water in Langley tank no. 2 and at the outdoor catapult. The scope of the tests consisted of ditching the models at various conditions of simulated damage, landing attitudes, and speeds, with various flap settings using several degrees of restraint of the flap hinges. The ditching behavior was evaluated from recordings of deceleration, length of run, and motions of the models. The results showed that the airplane should be ditched at an attitude of about 9 deg with flaps full down. The probable ditching behavior will be a smooth run with a maximum longitudinal deceleration of 3g to 4g and a landing run of 4 to 5 fuselage lengths. Structural failure of the underside of the fuselage will not seriously affect the behavior of the airplane.

Fisher, Lloyd J.↗
NASA NTRS2004

Neural network tracking and extension of positive tracking periods

Feature detectors have been considered for the role of supplying additional information to a neural network tracker. The feature detector focuses on areas of the image with significant information. Basically, if a picture says a thousand words, the feature detectors are looking for the key phrases (keypoints). These keypoints are rotationally invariant and may be matched across frames. Application of these advanced feature detectors to the neural network tracking system at JPL has promising potential. As part of an ongoing program, an advanced feature detector was tested for augmentation of a neural network based tracker. The advance feature detector extended tracking periods in test sequences including aircraft tracking, rover tracking, and simulated Martian landing. Future directions of research are also discussed.

feature extraction↗
NASA NTRS2008

Constitutive Soil Properties for Unwashed Sand and Kennedy Space Center

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle. This report provides constitutive material models for one soil, unwashed sand, from NASA Langley's gantry drop test facility and three soils from Kennedy Space Center (KSC). The four soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LS-DYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The four soil models are intended to be specific to the soil conditions discussed in the report. The unwashed sand model represents clayey sand at high density. The KSC models represent three distinct coastal sand conditions: low density dry sand, high density in-situ moisture sand, and high density flooded sand. It is possible to approximate other sands with these models, but the results would be unverified without geotechnical tests to confirm similar soil behavior.

Thomas, Michael A.↗
NASA NTRS2008

Constitutive Soil Properties for Cuddeback Lake, California and Carson Sink, Nevada

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle. This report provides constitutive material modeling properties for four soil models from two dry lakebeds in the western United States. The four soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples from the lakebeds. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LS-DYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The four soil models are intended to be specific only to the two lakebeds discussed in the report. The Cuddeback A and B models represent the softest and hardest soils at Cuddeback Lake. The Carson Sink Wet and Dry models represent different seasonal conditions. It is possible to approximate other clay soils with these models, but the results would be unverified without geotechnical tests to confirm similar soil behavior.

Thomas, Michael A.↗
NASA NTRS2011

Constitutive Soil Properties for Mason Sand and Kennedy Space Center

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle (CEV). This report provides constitutive material models for two soil conditions at Kennedy Space Center (KSC) and four conditions of Mason Sand. The Mason Sand is the test sand for LaRC s drop tests and swing tests of the Orion. The soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LSDYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The soil models are intended to be specific to the soil conditions they were tested at. The two KSC models represent two conditions at KSC: low density dry sand and high density in-situ moisture sand. The Mason Sand model was tested at four conditions which encompass measured conditions at LaRC s drop test site.

Thomas, Michael A.↗
NASA NTRS2013

Automated Loads Analysis System (ATLAS)

ATLAS is a generalized solution that can be used for launch vehicles. ATLAS is used to produce modal transient analysis and quasi-static analysis results (i.e., accelerations, displacements, and forces) for the payload math models on a specific Shuttle Transport System (STS) flight using the shuttle math model and associated forcing functions. This innovation solves the problem of coupling of payload math models into a shuttle math model. It performs a transient loads analysis simulating liftoff, landing, and all flight events between liftoff and landing. ATLAS utilizes efficient and numerically stable algorithms available in MSC/NASTRAN.

Gardner, Stephen↗
NASA NTRS2013

Hydroclimatic Controls on the Means and Variability of Vegetation Phenology and Carbon Uptake

Long-term, global offline (land-only) simulations with a dynamic vegetation phenology model are used to examine the control of hydroclimate over vegetation-related quantities. First, with a control simulation, the model is shown to capture successfully (though with some bias) key observed relationships between hydroclimate and the spatial and temporal variations of phenological expression. In subsequent simulations, the model shows that: (i) the global spatial variation of seasonal phenological maxima is controlled mostly by hydroclimate, irrespective of distributions in vegetation type, (ii) the occurrence of high interannual moisture-related phenological variability in grassland areas is determined by hydroclimate rather than by the specific properties of grassland, and (iii) hydroclimatic means and variability have a corresponding impact on the spatial and temporal distributions of gross primary productivity (GPP).

GPP↗
NASA NTRS2011

ATHLETE: Low Gravity Testbed

The All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) is a vehicle concept developed at Jet Propulsion Laboratory as a multipurpose robot for exploration. Currently, the ATHLETE team is working on creating a low gravity testbed to physically simulate ATHLETE landing on an asteroid. Several projects were worked on this summer to support the low gravity testbed.

rotary drill tool↗
NASA NTRS2012

Joint Chance-Constrained Dynamic Programming

This paper presents a novel dynamic programming algorithm with a joint chance constraint, which explicitly bounds the risk of failure in order to maintain the state within a specified feasible region. A joint chance constraint cannot be handled by existing constrained dynamic programming approaches since their application is limited to constraints in the same form as the cost function, that is, an expectation over a sum of one-stage costs. We overcome this challenge by reformulating the joint chance constraint into a constraint on an expectation over a sum of indicator functions, which can be incorporated into the cost function by dualizing the optimization problem. As a result, the primal variables can be optimized by a standard dynamic programming, while the dual variable is optimized by a root-finding algorithm that converges exponentially. Error bounds on the primal and dual objective values are rigorously derived. We demonstrate the algorithm on a path planning problem, as well as an optimal control problem for Mars entry, descent and landing. The simulations are conducted using a real terrain data of Mars, with four million discrete states at each time step.

Ono, Masahiro↗