Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mars systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Trade Study of Five In-Situ Propellant Production System for a Mars Sample Return Mission

One of the goals of NASA''s HEDS enterprise is to establish a long-term human presence on Mars at a fraction of the cost of employing today''s technology. The most direct method of reducing mission cost is to reduce the launch mass of the spacecraft. If the propellants for the return phase of the mission are produced on Mars, the total spacecraft mass could be reduced significantly. An interim goal is a Mars Sample Return (MSR) mission, which is proposed to demonstrate the feasibility of in-situ propellant production (ISPP). Five candidate ISPP systems for producing two fuels and oxygen from the Martian atmosphere are considered in this design trade-off study:(1) Zirconia cell with methanol synthesis, (2) Reverse water gas shift (RWGS) with water electrolysis and methanol synthesis, (3) Sabatier process for methane production with water electrolysis, (4) Sabatier process with water electrolysis and partial methane pyrolysis, and (5) Sabatier/RWGS combination with water electrolysis. These systems have been the subject of numerous previous analytical studies and laboratory demonstrations. In this investigation, the systems are objectively compared on the basis of thermochemical performance models using a commonly used chemical plant analysis software package. The realistic effects of incomplete chemical conversion and gas phase separator performance are included in these models. This study focuses on the chemical processing and product separation subsystems. The CO2 compression upstream of the chemical plane and the liquefaction/storage components are not included here.

Green, S. T.↗
NASA NTRS2020

An MBSE-based Approach to Architecting a Robotic Sample Capture System Concept for Potential Mars Sample Return

A model-based systems engineering (MBSE) approach was applied to architecting an orbiting sample Capture and Orient Module (COM) system concept for a Capture, Contain, and Return System (CCRS) payload concept for the notional Mars Sample Return (MSR) campaign at the NASA Jet Propulsion Laboratory. An architecture framework was established, covering multiple organizational layers of the system, along with structural, behavioral, data, and requirements perspectives. A workflow process to implement the architecting activities within the COM engineering team was established. The approach helped maintain consistency in terminology, helped ensure alignment of structural, behavioral, data, and requirements elements within each organization layer, and guided the engineering team through an architecting process that helped develop the architecture for a Capture and Orient Module system concept.

Younse, Paulo↗
NASA NTRS1992

Nuclear propulsion system options for Mars missions

This paper focuses on the use of a nuclear thermal rocket to accomplish a variety of space missions with emphasis on the manned Mars mission. The particle-bed-reactor type nuclear engine was chosen as the baseline engine because of its perceived versatility over other nuclear propulsion systems in conducting a wide variety of tasks. This study indicates that the particle-bed-reactor engine with its high engine thrust-to-weight ratio (about 20) and high specific impulse (about 950 to 1050 sec) offers distinct advantages over the larger and heavier NERVA-type nuclear engines.

Emrich, William J., Jr.↗
NASA NTRS1993

Drill/borescope System for the Mars Polar Pathfinder

The primary goals of the Mars Polar Pathfinder (MPP) Discovery Mission are to characterize the composition and structure of Mars' north polar ice cap, and to determine whether a climate record may be preserved in layers of ice and dust. The MPP would land as close as possible to the geographic north pole of Mars and use a set of instruments similar to those used by glaciologists to study polar ice caps on Earth: a radar sounder, a drill/borescope system, and a thermal probe. The drill/borescope system will drill approximately 50 cm into the surface and image the sides of the hole at 10 micron resolution for compositional and stratigraphic analysis. Several uncertainties have guided the development of this instrument, and they are discussed.

Paige, D. A.↗
NASA NTRS2013

A Mission Concept: Re-Entry Hopper-Aero-Space-Craft System on-Mars (REARM-Mars)

Future missions to Mars that would need a sophisticated lander, hopper, or rover could benefit from the REARM Architecture. The mission concept REARM Architecture is designed to provide unprecedented capabilities for future Mars exploration missions, including human exploration and possible sample-return missions, as a reusable lander, ascend/descend vehicle, refuelable hopper, multiple-location sample-return collector, laboratory, and a cargo system for assets and humans. These could all be possible by adding just a single customized Re-Entry-Hopper-Aero-Space-Craft System, called REARM-spacecraft, and a docking station at the Martian orbit, called REARM-dock. REARM could dramatically decrease the time and the expense required to launch new exploratory missions on Mars by making them less dependent on Earth and by reusing the assets already designed, built, and sent to Mars. REARM would introduce a new class of Mars exploration missions, which could explore much larger expanses of Mars in a much faster fashion and with much more sophisticated lab instruments. The proposed REARM architecture consists of the following subsystems: REARM-dock, REARM-spacecraft, sky-crane, secure-attached-compartment, sample-return container, agile rover, scalable orbital lab, and on-the-road robotic handymen.

Davoodi, Faranak↗
NASA NTRSDate not supplied

Improved Aerothermal Reliability Analysis Enabled by the Mars Sample Return Earth Entry System Aerothermal Database

The Mars Sample Return (MSR) campaign is a series of missions designed to retrieve Martian rock and soil samples for detailed study on Earth. The campaign is split into three primary phases: sample collection with the Mars2020 rover, retrieval with the Sample Return Lander (SRL) and Mars Ascent Vehicle (MAV), and then return to Earth with the Earth Return Orbiter (ERO) and Capture, Containment, and Return System (CCRS) [1]. The final sequence in the Earth return phase is the delivery and entry of the Earth Entry System (EES) sample return capsule. Due to unprecedented planetary protection concerns, the sample return capsule is subject to strict reliability requirements. To this end, the MSR-EES aerothermal team has implemented a flexible aerothermal database architecture capable of integration with state-of-the-art trajectory codes to provide a more rigorous aerothermal reliability analysis. The EES database enables the generation of environments at any location on the heatshield and can incorporate trajectory uncertainties to both statistically quantify aerothermal environments for arcjet testing and produce material response boundary conditions to rigorously select thermal protection system (TPS) sizing environments. This poster will not discuss the fundamental modeling assumptions included in the database, and will instead focus on the downstream reliability analyses that can be performed with a database of this architecture.

MSR-EES↗
NASA NTRS2013

Mars Science Laboratory Entry, Descent and Landing System Overview

The Mars Science Laboratory project recently places the Curiosity rove on the surface of Mars. With the success of the landing system, the performance envelope of entry, descent and landing capabilities has been extended over the previous state of the art. This paper will present an overview to the MSL entry, descent and landing system design and preliminary flight performance results.

MSL↗
NASA NTRS2002

Modeling Reaction Control System Effects on Mars Odyssey

During the Mars 2001 Odyssey aerobraking mission, NASA Langley Research Center performed 6 degree of freedom (6-DOF) simulations to determine rotational motion of the spacecraft. The main objective of this study was to assess the reaction control system models and their effects on the atmospheric flight of Odyssey. Based on these models, a comparison was made between data derived from flight measurements to simulated rotational motion of the spacecraft during aerobraking at Mars. The differences between the simulation and flight derived Odyssey data were then used to adjust the aerodynamic parameters to achieve a better correlation.

Hanna, Jill L.↗
NASA NTRSDate not supplied

Aeroheating Testing of the Mars Sample Return Earth Entry System with Surface Roughness

The Mars Sample Return Earth Entry System is a mission concept which would be the first NASA entry vehicle to utilize a woven thermal protection system as well as a 52.5 degree sphere-cone forebody geometry. Due to its novel design, historic experimental data sets were insufficient to validate the models used to characterize the expected aerothermal environment. A wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project in the NASA Langley 20-Inch Mach 6 Air Tunnel in order to obtain validation data. The December 2023 test entry of this campaign sought to obtain thermographic data to capture the impact of supersonic flow near woven surface roughness elements on convective heating augmentation, which was the largest remaining uncertainty in aerothermal design of the Earth Entry System. Data obtained were in family with prior results obtained on identical woven patterns without supersonic flow present at roughness elements, and it was found that this presence of supersonic flow did not have a noticeable effect on surface convective heating augmentation. Data were directly leveraged to support the NASA Mars Sample Return flight program and this data set is valuable for validating computational solutions on roughness-resolved grids.

Mars Sample Return↗
NASA NTRSDate not supplied

Aeroheating Testing of the Mars Sample Return Earth Entry System with Surface Roughness

The Mars Sample Return Earth Entry System is a mission concept which would be the first NASA entry vehicle to utilize a woven thermal protection system as well as a 52.5 degree sphere-cone forebody geometry. Due to its novel design, historic experimental data sets were insufficient to validate the models used to characterize the expected aerothermal environment. A wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project in the NASA Langley 20-Inch Mach 6 Air Tunnel in order to obtain validation data. The December 2023 test entry of this campaign sought to obtain thermographic data to capture the impact of supersonic flow near woven surface roughness elements on convective heating augmentation, which was the largest remaining uncertainty in aerothermal design of the Earth Entry System. Data obtained were in family with prior results obtained on identical woven patterns without supersonic flow present at roughness elements, and it was found that this presence of supersonic flow did not have a noticeable effect on surface convective heating augmentation. Data were directly leveraged to support the NASA Mars Sample Return flight program and this data set is valuable for validating computational solutions on roughness-resolved grids.

Mars Sample Return↗
NASA NTRS1984

Fluvial drainage systems: Margaritifer Sinus and Agyre (NC, NE) quadrangles, Mars

Fluvial drainage systems, delineated by mapping on stereo pairs of Viking Orbiter images, have developed in various-sized basins in the Margaritifer Sinus (MC-19) and Agyre (MC-26) Quadrangles, Mars. The Ladon Valles system is the largest, draining into and through two multi-ringed impact basins. Smaller fluvial basins to the southeast of the Ladon structural basin appear to have internal drainage. An intermediate-scale fluvial basin containing Himera Vallis extends along a north-south axis at 22 W and opens northward toward outflow channels south of Margaritifer Chaos. Stereo-pair mapping was extended furhter to the east, in MC-19 Ne, Se, and MC-26 NE, to investigate sources of outflow to the Ares Vallis system. The direction of flow in the channel at the northeast quadrant of the Ladon Basin is unresolved at present because of the poor quality of images available to form stereo pairs. However, an easterly drainage basin boundary running north-south along longitude 9 W, and extending westward at latitude 32-35 S, encloses a series of longitudinal drainage systems. Both the Parana Valles-Loire Vallis system and the Samara Valles system appear to drain in a northwesterly direction. The Samara flows to the Himera drainage basin, and the Parana-Loire to the northeast Ladon channel area.

Boothroyd, J. C.↗
NASA NTRS1990

Systems analysis of Mars solar electric propulsion vehicles

Mission performance, mass, initial power, and cost are determined for solar electric propulsion vehicles across a range of payload masses, reference powers, and mission trajectories. Thick radiation shielding is added to arrays using indium phosphide or III-V multijunction solar cells to reduce the damage incurred through the radiation belts. Special assessments of power management and distribution systems, atmospheric drag, and energy storage are made. It is determined that atmospheric drag is of no great concern and that the energy storage used in countering drag is unnecessary. A scheme to package the arrays, masts, and ion thrusters into a single fairing is presented.

Hickman, J. M.↗
NASA NTRSDate not supplied

Parametric Studies of Human Mars Entry, Descent, and Landing Systems

This paper will present a parametric analysis for entry, descent, and landing (EDL) concepts, enabling rapid systems assessment and tradespace exploration. The entry system uses a hypersonic inflatable aerodynamic decelerator (HIAD) technology. The baseline system includes elements for Mars aerocapture (AC) and EDL segments of the mission. The mission concept of operations (ConOps) begins at Mars arrival in a polar inclination. After performing an aerocapture (AC) maneuver into a pre-defined Mars parking orbit, the AC HIAD is jettisoned. The rest of thevehicle stays in the parking orbit for up to one year. The EDL sequence starts with a deorbit burn at the apoapsis of the parking orbit. After hypersonic entry with the EDL HIAD, the entry system uses a supersonic retropropulsion maneuver to slow the vehicle for the descent and landing segments of the mission. The vehicle will maintain a constant velocity of 2.5 m/s for 5 seconds prior to landing.The system includes a Mars Ascent Vehicle (MAV), Mars Descent Module (MDM), and two HIADs. The MDM includes a primary structure, tanks, engines, and radiators. The primary structure is an aluminum-lithium (Al-Li)cruciform design similar to the structural design of the Apollo Lunar Module. The cruciform planform layout results in four outer bays, with adequate volume in the corners between outer bays to package four landing gears. The central bay is reserved for packaging the MAV and the recessed MAV engines. Two of the outer bays accommodate main propellant tanks, with one LOX and one CH4 tank in each bay. The two remaining outer bays each house four rocket engine systems and associated support structure. Each HIAD comprises an inflatable structure, flexible thermal protection system, gas, and gas generators. The HIAD design used in this study is a stacked-toroid concept with pairing loop straps and radial/chevron straps. The baseline system lands a 20-t payload on the Mars surface. It is assumed the vehicle arrives at 6.2 km/s relative velocity at 90° inclination and is captured to a 1-Sol parking orbit.The baseline design includes many assumptions such as margins, arrival state, ConOps options, parking orbit, physical dimensions, propellant options, and technology concepts. The impact of these parameters are quantified through systems-level sensitivity analyses, which capture the global impact—not at a component level—but at the systems level. The systems-level sensitivities expose major design drivers and importance of each assumption for a design.Through tradespace exploration, a wide range of systems parameters are examined and compared for several feasible design options. Studies have been completed for the following input parameters: payload mass, propellant options, AC/EDL ballistic coefficient, lander thrust to weight ratio (T/W) (surrogate for the maximum EDL g’s),engine specific impulse (Isp), parking orbit, and inclination.The final paper will present and discuss the parametric approach used in the study. It will also include the results of recent systems analyses, sensitivity analyses, and tradespace exploration

Jamshid Samareh↗
NASA NTRS2017

Technology Development and Design of an Electrically Driven Pump Fed (EDPF) Bi-Propellant Propulsion System for a Mars Ascent Vehicle (MAV)

A Mars Ascent Vehicle (MAV), as part of a potential Mars Sample Return (MSR) campaign, is a very unique challenge and has been the focus of technology development and design efforts at JPL (Jet Propulsion Lab.) for several decades. Recent trajectory studies, for the current range of notional MAV payloads (6-25 kilograms), evaluated performance using propulsion systems in the 2.5 kiloNewton to 4.5 kiloNewton (600-1000 pounds-force) thrust range. The study examined several propulsion system approaches - solid rocket, bi-propellant and hybrid propulsion systems - and developed a ranking based on several key figures of merit. This paper focuses on the evaluations conducted for the two bi-propellant propulsion system options considered for a potential MAV. Historically, bi-propellant propulsion systems have been considered for this application; this study took a fresh look at both a conventional State of the Art (SOA) pressure fed bi-propellant propulsion system and recent developments using small EDPF (Electrically-Driven Pump-Fed) bi-propellant propulsion systems.

Vaughan, David↗
NASA NTRS2010

Implementation of a Relay Coordination System for the Mars Network

Mars network relay operations involve the coordination of lander and orbiter teams through long-term and short-term planning, tactical changes and post-pass analysis. Much of this coordination is managed through email traffic and point-to-point file data exchanges. It is often difficult to construct a complete and accurate picture of the relay situation at any given moment, as there is no centralized store of correlated relay data. The Mars Relay Operations Service (MaROS) is being implemented to address the problem of relay coordination for current and next-generation relay missions. The service is provided for the purpose of coordinating communications sessions between landed spacecraft assets and orbiting spacecraft assets at Mars. The service centralizes a set of functions previously distributed across multiple spacecraft operations teams, and as such greatly improves visibility into the end-to-end strategic coordination process. Most of the process revolves around the scheduling of communications sessions between the spacecraft during periods of time when a landed asset on Mars is geometrically visible by an orbiting spacecraft. These "relay" sessions are used to transfer data both to and from the landed asset via the orbiting asset on behalf of Earth-based spacecraft operators. This paper will discuss the relay coordination problem space, overview the architecture and design selected to meet system requirements, and describe the first phase of system implementation

Allard, Daniel A.↗