Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase slips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

The role of cobalt on the creep of Waspaloy

Cobalt was systematically replaced with nickel in Waspaloy (which normally contains 13% Co) to determine the effects of cobalt on the creep behavior of this alloy. Effects of cobalt were found to be minimal on tensile strengths and microstructure. The creep resistance and the stress rupture resistance determined in the range from 704 to 760 C (1300 to 1400 C) were found to decrease as cobalt was removed from the standard alloy at all stresses and temperatures. Roughly a ten-fold drop in rupture life and a corresponding increase in minimum creep rate were found under all test conditions. Both the apparent creep activation energy and the matrix contribution to creep resistance were found to increase with cobalt. These creep effects are attributed to cobalt lowering the stacking fault energy of the alloy matrix. The creep resistance loss due to the removal of cobalt is shown to be restored by slightly increasing the gamma' volume fraction. Results are compared to a previous study on Udimet 700, a higher strength, higher gamma' volume fraction alloy with similar phase chemistry, in which cobalt did not affect creep resistance. An explanation for this difference in behavior based on interparticle spacing and cross-slip is presented.

Jarrett, R. N.↗

Managing Small Spacecraft Projects: Less is Not Easier

Managing small, low cost missions (class C or D) is not necessarily easier than managing a full flagship mission. Yet, small missions are typically considered easier to manage and used as a training ground for developing the next generation of project managers. While limited resources can be a problem for small missions, in reality most of the issues inherent in managing small projects are not the direct result of limited resources. Instead, problems encountered by managers of small spacecraft missions often derive from 1) the perception that managing small projects is easier if something is easier it needs less rigor and formality in execution, 2) the perception that limited resources necessitate or validate omitting standard management practices, 3) less stringent or unclear guidelines or policies for small projects, and 4) stakeholder expectations that are not consistent with the size and nature of the project. For example, the size of a project is sometimes used to justify not building a full, detailed integrated master schedule. However, while a small schedule slip may not be a problem for a large mission, it can indicate a serious problem for a small mission with a short development phase, highlighting the importance of the schedule for early identification of potential issues. Likewise, stakeholders may accept a higher risk posture early in the definition of a low-cost mission, but as launch approaches this acceptance may change. This presentation discusses these common misconceptions about managing small, low cost missions, the problems that can result, and possible solutions.

Barley, Bryan↗

Coupled phase field damage and crystal plasticity analysis of intragranular fracture: The role of crystallographic orientation and voids

Damage evolution in engineering metal alloys at the grain scale exhibits significant microstructural heterogeneity and anisotropy. These heterogeneities create local hotspots for stress and strain localization, leading to void nucleation. Crystal orientation influences the active slip systems around voids, affecting lattice rotation and potentially forming discontinuities. At low triaxiality, voids may change shape due to lower stress, rotation, elongation, and coalescence. At high triaxiality, the correlation between crystal orientation and void growth rate becomes stronger, resembling the behavior observed in isolated single crystals. Therefore, understanding the effects of crystal orientation, heterogeneous strain, and defect evolution is crucial for single crystal fracture characterization. Here, in this work, a coupled phase-field damage (PFD) and crystal plasticity (CP) model is implemented within a finite element framework to analyze crystal deformation and failure. The CP method employs a dislocation density-based constitutive model, while intragranular failure is modeled using an anisotropic PFD method. The PFD model considers both the stored energy due to elastic stretching and the energy release due to defect formation and crack formation. A single crystal Al2219 with an intracrystalline spherical void is chosen to analyze fracture. The study finds that fracture propagation is strongly correlated with crystal orientations. This coupled CP-PFD model provides accurate failure prediction in crystalline materials by incorporating the effects of crystal orientations and existing voids. This study demonstrates how the local microstructure and defects influence plastic deformation and failure mechanisms in metal alloys.

Aluminum alloy↗

Widmannstätten laths in Ti48Al2Cr2Nb alloy by undercooled solidification

Widmannstätten laths in Ti48Al2Cr2Nb alloy were obtained by containerless electromagnetic levitation during undercooled solidification rather than heat treatments in most cases. The nucleation of γ{sub Widmannstätten} is confirmed by the thermal history of the second recalescence behaviour. High dislocation density, stacking faults and dislocation slip are observed by transmission electron microscopy. By quantitative analysis of the transformation energy, the driving force for γ{sub Widmannstätten} in the solid state phase transformation is calculated, compared with that of heat treatments. Meanwhile, the proper undercoolings (ΔT = 257–300 K), post-solidification cooling rates (11.1–29.1 K/s), the fine lamellar colony sizes (306–467 μm) and proper undercoolings in the solid state phase transformation are in favour of promoting the formation of Widmannstätten laths at moderate undercoolings. - Graphical abstract: Display Omitted - Highlights: • Widmannstätten laths were observed in undercooled TiAl alloy. • The influencing factors were discussed in undercooled TiAl alloy. • An analysis of the nucleation of γ{sub Widmannstätten} is carried out.

36 MATERIALS SCIENCE↗

Influence of Sn on Martensitic Beta Ti Alloys

The influence of Sn composition in Ti-17 at.% Nb alloys is studied by cyclic tension and in-situ synchrotron X-ray diffraction. It is essentially found that Sn stabilizes β-phase and effectively suppresses the formation of ω-phase. Along with β-phase stability, we detect lowering of the austenite and martensite transformation temperature by ~ 100 K/at.% and 88 K/at.%, respectively. Increasing Sn decreases the martensitic transformation strain in Ti-Nb alloys by ~ 1.4%/at.%, larger than that in Ti-Zr-Nb-Sn systems. The influence of Sn in martensitic Ti is anisotropic: causing larger reduction in lattice parameter b and higher decreases in elastic moduli of grain families that are aligned close to the b -axis. Lastly, a {013} α'' , {031} α'' ,{122} α'' and {211} α'' quadruple texture was observed in martensitic Ti wire. At the early stage of deformation, detwinning quickly rotated {013} α'' and (211} α'' , towards {031} α'' and {122} α'' components. After that, the strength of {031} α'' continued to increase, while the strength of {122} α'' texture was gradually decreased by dislocation slip as deformation continued.

36 MATERIALS SCIENCE↗

Charges on a suspended silicon nitride membrane under a high-energy electron beam

Thin silicon nitride (SiN x ) membranes are widely used in gas and liquid phase transmission electron microscopy (TEM) and as phase plates to enhance imaging contrast. SiN x contains trap sites for both positive and negative charges, which can be manipulated by high-energy electron irradiation, external potential biasing, or light exposure. Charge accumulation on the membrane can significantly affect in situ TEM processes, including chemical and electrochemical reactions, nanoparticle dynamics, and catalytic activity, or introduce unwanted phase shifts when used as a phase plate. Here, in this study, charge accumulation on suspended SiN x membranes was investigated using off-axis electron holography combined with model-free charge analysis, supported by custom finite element analysis (FEA) simulations. An average residual positive charge density of approximately 2.8 × 10 −4 C m −2 was measured. Localized and stable regions of both positive and negative charges were identified on the membrane. The global positive and localized positive/negative charges give rise to strong electric fields and electroosmotic slip velocities at the membrane surface, which are sufficient to induce non-Brownian particle behavior and directional fluid flow, offering a physical explanation for previously observed anomalies in particle dynamics, nucleation, and growth during gas and liquid phase TEM experiments. These results provide a benchmark for understanding charge behavior at SiNx interfaces in gas and liquid phase TEM. Furthermore, the FEA simulations establish a framework for future investigations into charge distribution, electrostatic potentials, and electrical double layers at solid–liquid interfaces, particularly in complex geometries and chemically dynamic environments.

Suspended silicon↗

Suppression of Twinning and Phase Transformation in an Ultrafine Grained 2 GPa Strong Metastable Austenitic Steel: Experiment and Simulation

An ultrafine-grained 304 austenitic 18 wt.%Cr-8 wt.%Ni stainless steel with a grain size of ~270 nm was synthesized by accumulative rolling (67 % total reduction) and annealing (550 °C, 150s). Uniaxial tensile testing at room temperature reveals an extremely high yield strength of 1890 ± 50MPa and a tensile strength of 2050 ± 30MPa, while the elongation reaches 6 ± 1%. Experimental characterization on samples with different grain sizes between 270 nm and 35 μm indicates that both, deformation twinning and martensitic phase transformation are significantly retarded with increasing grain refinement. A crystal plasticity finite element model incorporating a constitutive law reflecting the grain size-controlled dislocation slip and deformation twinning captures the micromechanical behavior of the steels with different grain sizes. Comparison of simulation and experiment shows that the deformation of ultrafine-grained 304 steels is dominated by the slip of partial dislocations, whereas for coarse-grained steels dislocation slip, twinning and martensite formation jointly contribute to the shape change.

Shen, Yongfeng↗

Multiscale formulation of frictional contact mechanics at the pore scale

Direct numerical simulation (DNS) yields the highest fidelity predictions of mechanical deformation at the pore scale, but is prohibitively expensive for analyzing large or many samples. Discrete element methods (DEM) are an efficient alternative, but are limited to granular media and incapable of estimating or controlling prediction errors. We present a pore-level multiscale method (PLMM) that approximates DNS efficiently and with controllable accuracy. We focus on the linear elastic response of a consolidated geologic porous medium with arbitrary microstructure, heterogeneous mineralogy, containing cracks or defects. PLMM decomposes the solid phase into non-overlapping subdomains, on which local basis functions are constructed. The bases are then coupled with a global interface problem that accounts for slip or stick contact conditions between the subdomains. PLMM produces an initial, but accurate, approximation to DNS that can be iteratively improved. It is amenable to parallelism and allows for different mesh, models, and physics in each subdomain. An algebraic interpretation of PLMM as a preconditioner is also presented to allow non-intrusive implementation into existing solvers. Lastly, this work extends previous developments of PLMM in fluid dynamics to solid mechanics and enables future extensions towards modeling coupled flow and mechanics problems.

42 ENGINEERING↗

Two-phase turbine staging

Two-phase turbines would be useful in Rankine cycles using low-quality or saturated-liquid working fluids. The chief problem is low efficiency due to slip losses in nozzles and due to liquid impact and friction losses in rotors. To raise efficiency, a staging method was tested in which the first stage operated at high speed with low relative liquid velocity, and the second stage recovered the first-stage exit energy. The theoretical efficiency for an experimental turbine operating with Refrigerant-22 was raised from 55 percent to 66 percent, and the measured efficiency was raised from 52 percent to 57 percent.

Elliott, D. G.↗

Strengthening mechanisms, hardening/softening behavior, and microstructure evolution in an LPSO magnesium alloy at elevated temperatures

Here, rapid degradation of the mechanical properties of conventional Mg alloys with temperature precludes their wide application in industry. The LPSO (long period stacking ordered) Mg alloys, on the other hand, show considerable potential to achieve excellent high-temperature mechanical performance. In this study, a Mg-5.1Y-2.4Zn (wt.%) extrusion alloy with the microstructure comprising of α-Mg matrix and LPSO phase was prepared. It is shown that the yield strength of the alloy at 200 °C retained ~83% of the yield strength of 198 MPa at room temperature (RT). Importantly, the ductility also improved, owing to the increased non-basal slip activities at elevated temperatures. In contrast to RT and 200 °C, the alloy exhibited softening tensile behavior with an apparent loss of yield strength at 300 °C. In-situ lattice strain analysis revealed that load transfer from α-Mg to LPSO remains effective at temperatures up to 200 °C, governing the high yield strength of the alloy. The post-mortem analysis by means of electron microscopy confirmed that the LPSO phase is structurally stable at 200 °C. In particular, the high strain hardenability is rationalized by the sandwiched LPSO structures together with stacking faults serving as effective obstacles to the motion of non-basal dislocations. The load transfer effect disappears at the temperature of 300 °C, resulting in the fast deterioration of strength of the alloy. The cracking of the LPSO phase along with the recrystallizing of α-Mg grains were found to be the main causes for the softening behavior of the alloy at 300 °C.

36 MATERIALS SCIENCE↗

DENSITY EFFECT OF SOLIDIFIED HYDROGEN ISOTOPE PARTICLES ON PARTICLE IMAGE VELOCIMETRY MEASUREMENTS OF HE II FLOW

Solid H{sub 2}, D{sub 2} and H{sub 2}/D{sub 2} particles can be generated in He II by solidifying directly from the gas phase. Here we compare these three different particles as tracers for tracking He II forced flow in a horizontal channel using the Particle Image Velocimetry (PIV) technique. Slip velocity measurements show that all generated particles are in the micron size range. Steady state velocity fields of the forced flow of He II within a square cross-section channel are measured. By comparing the results obtained from different tracers, we show that the slip velocity caused by non-neutral buoyancy of these particles does not affect the measured velocity profiles of He II forced flow.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. 3: Tension-compression anisotropy

Single crystal superalloy specimens with various crystallographic directions along their axes were tested in compression at room temperature, 650, 760, 870, and 980 deg C. These results are compared with the tensile behavior studied previously. The alloy, Rene N4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo 9 Cr. 7.5 Co, balance Ni, in weight percent. Slip trace analysis showed that primary cube slip occurred even at room temperature for the 111 specimens. With increasing test temperature more orientations exhibited primary cube slip, until at 870 deg C only the 100 and 011 specimens exhibited normal octahedral slip. The yield strength for octahedral slip was numerically analysed using a model proposed by Lall, Chin, and Pope to explain deviations from Schmid's Law in the yielding behavior of a single phase Gamma prime alloy, Ni3(Al, Nb). The Schmid's Law deviations in Rene N4 were found to be largely due to a tension-compression anisotropy. A second effect, which increases trength for orientations away from 001, was found to be small in Rene N4. Analysis of recently published data on the single crystal superalloy PWA 1480 yielded the same result.

Miner, R. V.↗

Shape-driven, emergent behavior in active particle mixtures

Abstract Active particle systems can vary greatly from one-component systems of spheres to mixtures of particle shapes at different composition ratios. We investigate computationally the combined effect of anisotropy and stoichiometry on the collective behavior of two-dimensional active colloidal mixtures of polygons. We uncover three emergent phenomena not yet reported in active Brownian particle systems. First, we find that mixtures containing hexagons exhibit micro-phase separation with large grains of hexagonal symmetry. We quantify a measurable, implicit ‘steric attraction’ between the active particles as a result of shape anisotropy and activity. This calculation provides further evidence that implicit interactions in active systems, even without explicit attraction, can lead to an effective preferential attraction between particles. Next, we report stable fluid clusters in mixtures containing one triangle or square component. We attribute the fluidization of the dense cluster to the interplay of cluster destabilizing particles, which introduce grain boundaries and slip planes into the system, causing solid-like clusters to break up into fluid clusters. Third, we show that fluid clusters can coexist with solid clusters within a sparse gas of particles in a steady state of three coexisting phases. Our results highlight the potential for a wide variety of behavior to be accessible to active matter systems and establish a route to control active colloidal systems through simple parameter designs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A novel multistage estimation of signal parameters

A multistage estimation scheme is presented for estimating the parameters of a received carrier signal possibly phase-modulated by unknown data and experiencing very high Doppler, Doppler rate, etc. Such a situation arises, for example, in the case of the Global Positioning Systems (GPS). In the proposed scheme, the first-stage estimator operates as a coarse estimator of the frequency and its derivatives, resulting in higher rms estimation errors but with a relatively small probability of the frequency estimation error exceeding one-half of the sampling frequency (an event termed cycle slip). The second stage of the estimator operates on the error signal available from the first stage, refining the overall estimates, and in the process also reduces the number of cycle slips. The first-stage algorithm is a modified least-squares algorithm operating on the differential signal model and referred to as differential least squares (DLS). The second-stage algorithm is an extended Kalman filter, which yields the estimate of the phase as well as refining the frequency estimate. A major advantage of the is a reduction in the threshold for the received carrier power-to-noise power spectral density ratio (CNR) as compared with the threshold achievable by either of the algorithms alone.

Kumar, Rajendra↗

Nevada Great Basin Play Fairway Analysis Regional Data

This project focused on defining geothermal play fairways and development of a detailed geothermal potential map of a large transect across the Great Basin region (96,000 km2), with the primary objective of facilitating discovery of commercial-grade, blind geothermal fields (i.e. systems with no surface hot springs or fumaroles) and thereby accelerating geothermal development in this promising region. Data included in this submission consists of: structural settings (target areas, recency of faulting, slip and dilation potential, slip rates, quality), regional-scale strain rates, earthquake density and magnitude, gravity data, temperature at 3 km depth, permeability models, favorability models, degree of exploration and exploration opportunities, data from springs and wells, transmission lines and wilderness areas, and published maps and theses for the Nevada Play Fairway area.

130C↗

Space Cryogenics Workshop, University of Wisconsin, Madison, June 22, 23, 1987

Papers are presented on liquid helium servicing from the Space Station, performance estimates in the Superfluid Helium On-Orbit Transfer Flight Experiment, an analytical study of He II flow characteristics in the SHOOT transfer line, a Dewar to Dewar model for superfluid helium transfer, and mechanical pumps for superfluid helium transfer in space. Attention is also given to the cavitation characteristics of a small centrifugal pump in He I and He II, turbulent flow pressure drop in various He II transfer system components, slip effects associated with Knudsen transport phenomena in porous media, and an integrated fountain effect pump device for fluid management at low gravity. Other papers are on liquid/vapor phase separation in He-4 using electric fields, an enclosed capillary device for low-gravity management of He II, cavitation in flowing superfluid helium, the long-term performance of the passive thermal control systems of the IRAS spacecraft, and a novel approach to supercritical helium flight cryostat support structures.

Source record↗

An automatic editing algorithm for GPS data

An algorithm has been developed to edit automatically Global Positioning System data such that outlier deletion, cycle slip identification, and correction are independent of clock instability, selective availability, receiver-satellite kinematics, and tropospheric conditions. This algorithm, called TurboEdit, operates on undifferenced, dual frequency carrier phase data, and requires the use of P code pseudorange data and a smoothly varying ionospheric electron content. TurboEdit was tested on the large data set from the CASA Uno experiment, which contained over 2500 cycle slips.Analyst intervention was required on 1 percent of the station-satellite passes, almost all of these problems being due to difficulties in extrapolating variations in the ionospheric delay. The algorithm is presently being adapted for real time data editing in the Rogue receiver for continuous monitoring applications.

Blewitt, Geoffrey↗

The Parable of the Boiled Safety Professional

Common and unique issues contribute to system failures. This paper touches on the concept of drift to failure as a cautionary message. Managers and leaders, design team members, fabricators and assemblers, analysis and assurance personnel, and others associated with operating and maintaining systems, need to pay attention to identify the manifestation of individual and collective behaviors that might indicate slips in rigor or focus or decisions that might eat away at safety margins as our system drifts to failure. Corrections to drift made during design and development phases may efficiently prevent or mitigate drift problems occurring in the operational phase.

Shivers, Charles H.↗