SEARCH · Search NASA

Results for “Positioning Navigation Timing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

GPS Multipath Emulation using Software Generated Signals

Depending on the environment, multipath can be one of the largest error sources contributing to degradation in Global Navigation Satellite System (GNSS) (e.g., GPS) performance. Currently, open-source tools for simulating GPS signals are available and can be used in the testing and evaluation of GPS receiver equipment. These tools can generate GPS signals that, when used by a GPS receiver, result in computation of a position solution that was pre-determined at the time of signal generation. This work utilizes a custom version of the open-source GPS-SDR-SIM to produce emulated multipath GPS signals. A proof of concept was prototyped and demonstrated using this modified version of GPS-SDR-SIM to produce GPS as well as multipath signals. The generated data was processed using a software defined GPS receiver (GNSS-SDR) and it was found that the introduction of simulated multipath signals successfully produced the expected characteristics of a composite multipath signal in simulation.

GPS↗

NASA NTRSDate not supplied

GPS Multipath Emulation using Software Generated Signals

GPS↗

NASA NTRS2008

A Performance Assessment of an Airborne Separation Assistance System Using Realistic Complex Traffic Flows

This paper presents the results from a study that investigates the performance of a tactical Airborne Separation Assistance System (ASAS) in en route airspace, under varying demand levels, with realistic traffic flows. The ASAS concept studied here allows flight crews of equipped aircraft to perform separation from other air traffic autonomously. This study addresses the tactical aspects of an ASAS using aircraft state data (i.e. position and velocity) to detect and resolve projected conflicts. In addition, use of a conflict prevention system helps ASAS-equipped aircraft avoid maneuvers that may cause new conflicts. ASAS-capable aircraft are equipped with satellite-based navigation and Automatic Dependent Surveillance Broadcast (ADS-B) for transmission and receipt of aircraft state data. In addition to tactical conflict detection and resolution (CD&R), a complete, integrated ASAS is likely to incorporate a strategic CD&R component with a longer look-ahead time, using trajectory intent information. A system-wide traffic flow management (TFM) component, located at the FAA command center helps aircraft to avoid regions of excessive traffic density and complexity. A Traffic Alert and Collision Avoidance System (TCAS), as used today is the system of last resort. This integrated approach avoids sole reliance on the use of the tactical CD&R studied here, but the tactical component remains a critical element of the complete ASAS. The focus of this paper is to determine to what extent the proposed tactical component of ASAS alone can maintain aircraft separation at demand levels up to three times that of current traffic. The study also investigates the effect of mixing ASAS-equipped aircraft with unequipped aircraft (i.e. current day) that do not have the capability to self-separate. Position and velocity data for unequipped aircraft needs to be available to ASASequipped. Most likely, for this future concept, state data would be available from instrument flight rules (IFR) aircraft, equipped with at least ADS-B transmission capability. The objective is to reduce the number of losses of separation to a minimum and investigate the limits of tactical-only CD&R. Thus, the objective is not, expressly, to achieve zero losses of separation with tactical ASAS because this is one component of an integrated ASAS.

Smith, Jeremy C.↗

NASA NTRS2000

Ionosphere Delay Calibration and Calibration Errors for Satellite Navigation of Aircraft

The Federal Aviation Administration (FAA) is implementing a satellite-based navigation system for aircraft using the Global Positioning System (GPS). Positioning accuracy of a few meters will be achieved by broadcasting corrections to the direct GPS signal. These corrections are derived using the wide-area augmentation system (WAAS), which includes a ground network of at least 24 GPS receivers across the Continental US (CONUS). WAAS will provide real-time total electron content (TEC) measurements that can be mapped to fixed grid points using a real-time mapping algorithm. These TECs will be converted into vertical delay corrections for the GPS L1 frequency and broadcast to users every five minutes via geosynchronous satellite. Users will convert these delays to slant calibrations along their own lines-of-sight (LOS) to GPS satellites. Uncertainties in the delay calibrations will also be broadcast, allowing users to estimate the uncertainty of their position. To maintain user safety without reverting to excessive safety margins an empirical model of user calibration errors has been developed. WAAS performance depends on factors that include geographic location (errors increase near WAAS borders), and ionospheric conditions, such as the enhanced spatial electron density gradients found during ionospheric storms.

Harris, Ian↗

NASA NTRS1996

Off-the-shelf real-time monitoring of satellite constellations in a visual 3-D environment

The multimission spacecraft analysis system (MSAS) data monitor is a generic software product for future real-time data monitoring and analysis. The system represents the status of a satellite constellation through the shape, color, motion and position of graphical objects floating in a three dimensional virtual reality environment. It may be used for the monitoring of large volumes of data, for viewing results in configurable displays, and for providing high level and detailed views of a constellation of monitored satellites. It is considered that the data monitor is an improvement on conventional graphic and text-based displays as it increases the amount of data that the operator can absorb in a given period, and can be installed and configured without the requirement for software development by the end user. The functionality of the system is described, including: the navigation abilities; the representation of alarms in the cybergrid; limit violation; real-time trend analysis, and alarm status indication.

Schwuttke, Ursula M.↗

NASA NTRS1973

Recent results from satellite beacon measurements

The techniques are reviewed for measuring ionospheric electron content, the most important parameter in the study of transionospheric propagation. Data collected since 1964 have yielded a synoptic description of the behavior of the electron content in midlatitudes. Empirical relationships between the level of solar activity and the electron content were developed permitting the prognostication of the electron content values. Construction of such prognostication schemes was stimulated by current efforts to create accurate satellite borne navigation systems. Gravity waves propagating in the thermosphere leave a signature in the electron content records. Studies of such records have allowed the identification of the position of the gravity wave source, and its radiation pattern. A one-to-one relationship between these waves and polar substorms was revealed. Electron content measurements were used to monitor the protonosphere with good time resolution. Protonospheric storms were observed with this technique. Slab thickness data obtained from content measurements were used to determine the neutral air temperature in the thermosphere.

Darosa, A. V.↗

NASA NTRS2018

Onboard Stereo Vision for Drone Pursuit or Sense and Avoid

Wedescribeanew,on-board,shortrangeperceptionsystem that enables micro aerial vehicles (MAVs) to detect, track, and follow or avoid nearby drones (within 2-20 meters) in GPS-denied environments. Each vehicle is able to sense its neighborhood and adapt its motion accordingly without use of centralized reasoning or inter-vehicle communication. To enable a lightweight, low power solution, on-board stereo cameras are used for detection and tracking with depth images, while a downward-looking camera and an inertial measurement unit are used to estimate the position of the observer without use of GPS. We illustrate the robustness and accuracy of this approach through real-time, outdoor leader-follower experiments with three quadrotors. Our experiments show that state-of-art trackers are far less robust in detection against cluttered background. This demonstrates that stereo vision is a highly effective approach to perception for safe navigation of multiple MAVs in close proximity.

Matthies, Larry↗

NASA NTRS2012

Longitudinal Differences of Ionospheric Vertical Density Distribution and Equatorial Electrodynamics

Accurate estimation of global vertical distribution of ionospheric and plasmaspheric density as a function of local time, season, and magnetic activity is required to improve the operation of space-based navigation and communication systems. The vertical density distribution, especially at low and equatorial latitudes, is governed by the equatorial electrodynamics that produces a vertical driving force. The vertical structure of the equatorial density distribution can be observed by using tomographic reconstruction techniques on ground-based global positioning system (GPS) total electron content (TEC). Similarly, the vertical drift, which is one of the driving mechanisms that govern equatorial electrodynamics and strongly affect the structure and dynamics of the ionosphere in the low/midlatitude region, can be estimated using ground magnetometer observations. We present tomographically reconstructed density distribution and the corresponding vertical drifts at two different longitudes: the East African and west South American sectors. Chains of GPS stations in the east African and west South American longitudinal sectors, covering the equatorial anomaly region of meridian approx. 37 deg and 290 deg E, respectively, are used to reconstruct the vertical density distribution. Similarly, magnetometer sites of African Meridian B-field Education and Research (AMBER) and INTERMAGNET for the east African sector and South American Meridional B-field Array (SAMBA) and Low Latitude Ionospheric Sensor Network (LISN) are used to estimate the vertical drift velocity at two distinct longitudes. The comparison between the reconstructed and Jicamarca Incoherent Scatter Radar (ISR) measured density profiles shows excellent agreement, demonstrating the usefulness of tomographic reconstruction technique in providing the vertical density distribution at different longitudes. Similarly, the comparison between magnetometer estimated vertical drift and other independent drift observation, such as from VEFI onboard Communication/Navigation Outage Forecasting System (C/NOFS) satellite and JULIA radar, is equally promising. The observations at different longitudes suggest that the vertical drift velocities and the vertical density distribution have significant longitudinal differences; especially the equatorial anomaly peaks expand to higher latitudes more in American sector than the African sector, indicating that the vertical drift in the American sector is stronger than the African sector.

total electron content↗

DOE OSTI2025

Governance and resilience as entry points for transforming food systems in the countdown to 2030

Due to complex interactions, changes in any one area of food systems are likely to impact—and possibly depend on—changes in other areas. Here we present the first annual monitoring update of the indicator framework proposed by the Food Systems Countdown Initiative, with new qualitative analysis elucidating interactions across indicators. Since 2000, we find that 20 of 42 indicators with time series have been trending in a desirable direction, indicating modest positive change. Qualitative expert elicitation assessed governance and resilience indicators to be most connected to other indicators across themes, highlighting entry points for action—particularly governance action. Literature review and country case studies add context to the assessed interactions across diets, environment, livelihoods, governance and resilience indicators, helping different actors understand and navigate food systems towards desirable change.

Schneider, Kate R. [Johns Hopkins Univ., Washingto↗

NASA NTRS1995

Wakeshield WSF-02 GPS Experiment

Shuttle mission STS-69 was launched on September 7, 1995, 10:09 CDT, carrying the Wake Shield Facility (WSF-02). The WSF-02 spacecraft included a set of payloads provided by the Texas Space Grant Consortium, known as TexasSat. One of the TexasSat payloads was a GPS TurboRogue receiver loaned by the University Corporation for Atmospheric Research. On September 11, the WSF-02 was unberthed from the Endeavour payload bay using the remote manipulator system. The GPS receiver was powered on prior to release and the WSF-02 remained in free-flight for three days before being retrieved on September 14. All WSF-02 GPS data, which includes dual frequency pseudorange and carrier phase, were stored in an on-board recorder for post-flight analysis, but "snap- shots" of data were transmitted for 2-3 minutes at intervals of several hours, when permitted by the telemetry band- widdl The GPS experiment goals were: (1) an evaluation of precision orbit determination in a low altitude environment (400 km) where perturbations due to atmospheric drag and the Earth's gravity field are more pronounced than for higher altitude satellites with high precision orbit requirements, such as TOPEX/POSEIDON; (2) an assessment of relative positioning using the WSF GPS receiver and the Endeavour Collins receiver; and (3) determination of atmospheric temperature profiles using GPS signals passing through the atmosphere. Analysis of snap-shot telemetry data indicate that 24 hours of continuous data were stored on board, which includes high rate (50 Hz) data for atmosphere temperature profiles. Examination of the limited number of real-time navigation solutions show that at least 7 GPS satellites were tracked simultaneously and the on-board clock corrections were at the microsec level, as expected. Furthermore, a dynamical consistency test provided a further validation of the on-board navigation solutions. Complete analysis will be conducted in post-flight using the data recorded on-board.

Schutz, B. E.↗

NASA NTRSDate not supplied

Lunar Pathfinder Laser Retroreflector Array

ESA’s Lunar Pathfinder mission is scheduled to launch and orbit the Moon at the end of 2024 in an elliptical lunar frozen orbit. The mission will provide lunar communication services and host a Navigation In-Orbit-Demonstration payload that will use Global Navigational Satellite System (GNSS) signals from the moon for positioning. NASA is providing a laser retroreflector array (LRA) for this mission to validate the GNSS-based positioning and demonstrate two-way laser ranging in support of precision orbit determination for lunar missions. The LRA consists of 48 x 4.06 cm diameter uncoated cube corners that will provide an optical cross section around 10 times larger than LRA on the Lunar Reconnaissance Orbiter (LRO). This increased cross section along with regular dedicated periods where the LRA is pointed towards Earth should significantly reduce the challenges encountered during laser ranging to LRO. An overview of the Lunar Pathfinder mission will be presented along with results from optical measurements of the Lunar Pathfinder LRA.

Stephen M Merkowitz↗

NASA NTRS2023

Testing the Gravitational Redshift With an Inner Solar System Probe: the Veritas Case

The NASA Discovery-class mission VERITAS, selected in June 2021, will be launched towards Venus after 2027. In addition to the science instrumentation that will build global foundational geophysical datasets, VERITAS proposed to conduct a technology demonstration for the Deep Space Atomic Clock (DSAC-2). A first DSAC successfully operated in low-Earth orbit for more than two years, demonstrated the trapped ion atomic clock technology, and established a new level of performance for clocks in space. DSAC-2 would have further improvements in size, power, and performance. It would host a 1× 10 -13 grade USO to produce a frequency output with short-term stability of less than 2× 10 -13 /√ τ (where τ is the averaging time).However, due to funding shortfalls, DSAC-2, had to be canceled. The initially foreseen presence of an atomic clock on board the probe, however, raised the question whether this kind of instrumentation could be useful not only for navigation and time transfer but also for fundamental physics tests. In this work, we consider the DSAC-2 atomic clock and VERITAS mission as a specific example to measure possible discrepancies in the redshift predicted by General Relativity by using an atomic clock onboard an interplanetary spacecraft. In particular we investigate the possibility of measuring possible violations of the Local Lorentz Invariance and Local Position Invariance principles. We perform accurate simulations of the experiment during the VERITAS cruise phase. We consider different parametrizations of the possible violations of the General Relativity, different operational conditions, and several different assumptions on the expected measurement performance. We show that DSAC-2 onboard VERITAS would provide new and improved constraints with respect to the current knowledge. Our analysis shows the scientific value of atomic clocks like DSAC-2 hosted onboard interplanetary spacecraft.

Fabrizio De Marchi↗

NASA NTRS1976

Possible methods for USSR-VLF navigation receivers

The U.S.S.R. has a VLF navigation system similar to OMEGA. Beukers has reported some information on the signal format, frequencies used, and the probable radiated power levels. From this data it appears possible to derive receiver operation modes and some implied reasons for the unique choice of the time-multiplexed frequency time base used. Of interest are receiver methods requiring processor gate complexity similar to a digital wristwatch including the use of mass-produced low frequency quartz crystal reference oscillators. The stability required of the local reference oscillator is probably much less critical than for other VLF receivers because of the signal format. One conclusion is that U.S.S.R.-VLF receivers might be fabricated at quite low cost making it possible for all persons in remote areas each to have his own private positioning aid. Further study of the actual transmitted signal format is warranted. While the nature of this memorandum is speculative because of the lack of confirming data, the receiver method proposed has evolved from related principles which have been applied to the operating OMEGA-VLF navigation system.

Burhans, R. W.↗

NASA NTRS2017

UAV Inspection of Electrical Transmission Infrastructure with Path Conformance Autonomy and Lidar-Based Geofences NASA Report on UTM Reference Mission Flights at Southern Company Flights November 2016

Flights at low altitudes in close proximity to electrical transmission infrastructure present serious navigational challenges: GPS and radio communication quality is variable and yet tight position control is needed to measure defects while avoiding collisions with ground structures. To advance unmanned aerial vehicle (UAV) navigation technology while accomplishing a task with economic and societal benefit, a high voltage electrical infrastructure inspection reference mission was designed. An integrated air-ground platform was developed for this mission and tested in two days of experimental flights to determine whether navigational augmentation was needed to successfully conduct a controlled inspection experiment. The airborne component of the platform was a multirotor UAV built from commercial off-the-shelf hardware and software, and the ground component was a commercial laptop running open source software. A compact ultraviolet sensor mounted on the UAV can locate 'hot spots' (potential failure points in the electric grid), so long as the UAV flight path adequately samples the airspace near the power grid structures. To improve navigation, the platform was supplemented with two navigation technologies: lidar-to-polyhedron preflight processing for obstacle demarcation and inspection distance planning, and trajectory management software to enforce inspection standoff distance. Both navigation technologies were essential to obtaining useful results from the hot spot sensor in this obstacle-rich, low-altitude airspace. Because the electrical grid extends into crowded airspaces, the UAV position was tracked with NASA unmanned aerial system traffic management (UTM) technology. The following results were obtained: (1) Inspection of high-voltage electrical transmission infrastructure to locate 'hot spots' of ultraviolet emission requires navigation methods that are not broadly available and are not needed at higher altitude flights above ground structures. (2) The sensing capability of a novel airborne UV detector was verified with a standard ground-based instrument. Flights with this sensor showed that UAV measurement operations and recording methods are viable. With improved sensor range, UAVs equipped with compact UV sensors could serve as the detection elements in a self-diagnosing power grid. (3) Simplification of rich lidar maps to polyhedral obstacle maps reduces data volume by orders of magnitude, so that computation with the resultant maps in real time is possible. This enables real-time obstacle avoidance autonomy. Stable navigation may be feasible in the GPS-deprived environment near transmission lines by a UAV that senses ground structures and compares them to these simplified maps. (4) A new, formally verified path conformance software system that runs onboard a UAV was demonstrated in flight for the first time. It successfully maneuvered the aircraft after a sudden lateral perturbation that models a gust of wind, and processed lidar-derived polyhedral obstacle maps in real time. (5) Tracking of the UAV in the national airspace using the NASA UTM technology was a key safety component of this reference mission, since the flights were conducted beneath the landing approach to a heavily used runway. Comparison to autopilot tracking showed that UTM tracking accurately records the UAV position throughout the flight path.

Moore, Andrew J.↗

NASA NTRS1990

Error analysis for earth orientation recovery from GPS data

The use of GPS navigation satellites to study earth-orientation parameters in real-time is examined analytically with simulations of network geometries. The Orbit Analysis covariance-analysis program is employed to simulate the block-II constellation of 18 GPS satellites, and attention is given to the budget for tracking errors. Simultaneous solutions are derived for earth orientation given specific satellite orbits, ground clocks, and station positions with tropospheric scaling at each station. Media effects and measurement noise are found to be the main causes of uncertainty in earth-orientation determination. A program similar to the Polaris network using single-difference carrier-phase observations can provide earth-orientation parameters with accuracies similar to those for the VLBI program. The GPS concept offers faster data turnaround and lower costs in addition to more accurate determinations of UT1 and pole position.

Zelensky, N.↗

NASA NTRS1995

Fault detection and exclusion in multisensor navigation systems

In order for a multisensor navigation system to meet integrity requirements, there must be a way of detecting erroneous measurements, using only data from those measurements. This can be accomplished using a parity space estimation algorithm. Erroneous measurements must then be removed from the position solution; the entire process is called fault detection and exclusion (FDE). A baseline FDE algorithm has been determined, and is capable of working in real time on present affordable hardware.

Bernath, Gregory N.↗

NASA NTRS2010

CCSDS - Advancing Spaceflight Technology for International Collaboration

The Consultative Committee for Space Data Systems (CCSDS) has been developing data and communications standards since 1982, with the objective of providing interoperability for enabling international collaboration for spaceflight missions. As data and communications technology has advanced, CCSDS has progressed to capitalize on existing products when available and suitable for spaceflight, and to develop innovative new approaches when available products fail. The current scope of the CCSDS architecture spans the end-to-end data architecture of a spaceflight mission, with ongoing efforts to develop and standardize cutting-edge technology. This manuscript describes the overall architecture, the position of CCSDS in the standards and international mission community, and some CCSDS processes. It then highlights in detail several of the most interesting and critical technical areas in work right now, and how they support collaborative missions. Special topics include: Delay/Disruption Tolerant Networking (DTN), Asynchronous Message Service (AMS), Multispectral/Hyperspectral Data Compression (MHDC), Coding and Synchronization, Onboard Wireless, Spacecraft Monitor and Control, Navigation, Security, and Time Synchronization/Correlation. Broad international participation in development of CCSDS standards is encouraged.

Kearney, Mike↗

NASA NTRS1972

The Global Rescue Alarm Net (GRAN) experiment

The OMEGA Position Location Experiment (OPLE) was performed in 1967 by the Goddard Space Flight Center in order to demonstrate a position location and data collection system. OMEGA navigation signals were received at a remote site and retransmitted via a synchronous satellite to a ground processing center where data collecting and position determination were performed. Recent technological advances have made it possible to develop an Advanced OPLE System towards a global search and rescue application. This application generated some new problem areas such as the OMEGA lane ambiguity, random access, location accuracy, real-time processing, and size and weight of the Search and Rescue Communications (SARCOM). This experiment demonstrates the feasibility of instantaneous alarm and position location by using a relatively inexpensive, battery operated, three-pound package.

Morakis, J. C.↗