Search NASA⌕ Search

SEARCH · Search NASA

Results for “Predictive analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Three-dimensional stability of an elliptical vortex in a straining field

The three-dimensional linear stability of a rectilinear vortex of elliptical cross-section existing as a steady state in an irrotational straining field is studied numerically in the case of finite strain. It is shown that the instability predicted analytically for weak strain persists for finite strain and that the weak-strain results continue to be quantitatively valid for finite strain. The dependence of the growth rates of the unstable modes on the strain and the axial-disturbance wavelength is discussed. It is also shown that a three-dimensional instability is always more unstable than a two-dimensional instability in the range of parameters of most interest.

Robinson, A. C.↗
NASA NTRS1984

Demonstration of transparent solar array module design

This report discusses the design, development, fabrication and testing of IR transparent solar array modules. Three modules, consisting of a baseline design using back surface reflector cells, and two modules using gridded back contact, IR transparent cells, were subjected to vacuum thermal balance testing to verify analytical predictions of lower operating emperature and increased efficiency. As a result of this test program, LMSC has verified that a significant degree of IR transparency can be designed into a flexible solar array. Test data correlates with both steady state and transient thermal analysis.

Pack, G. J.↗
NASA NTRS1985

A method for estimating the rolling moment due to spin rate for arbitrary planform wings

The application of aerodynamic theory for estimating the force and moments acting upon spinning airplanes is of interest. For example, strip theory has been used to generate estimates of the aerodynamic characteristics as a function of spin rate for wing-dominated configurations for angles of attack up to 90 degrees. This work, which had been limited to constant chord wings, is extended here to wings comprised of tapered segments. Comparison of the analytical predictions with rotary balance wind tunnel results shows that large discrepancies remain, particularly for those angles-of-attack greater than 40 degrees.

Poppen, W. A., Jr.↗
NASA NTRS1985

Fatigue life analysis of a turboprop reduction gearbox

A fatigue life analysis of the Allison T56/501 turboprop reduction gearbox was developed. The life and reliability of the gearbox was based on the lives and reliabilities of the main power train bearings and gears. The bearing and gear lives were determined using the Lundberg-Palmgren theory and a mission profile. The five planet bearing set had the shortest calculated life among the various gearbox components, which agreed with field experience where the planet bearing had the greatest incidences of failure. The analytical predictions of relative lives among the various bearings were in reasonable agreement with field experience. The predicted gearbox life was in excellent agreement with field data when the material life adjustment factors alone were used. The gearbox had a lower predicted life in comparison with field data when no life adjustment factors were used or when lubrication life adjustment factors were used either alone or in combination with the material factors.

Lewicki, D. G.↗
NASA NTRS1985

Hypersonic characteristics of an advanced aerospace plane

A series of hypersonic wind-tunnel tests have been conducted in the NASA Langley Hypersonic Facilities Complex to obtain the static longitudinal and lateral-directional aerodynamic characteristics of an advanced aerospace plane. Data were obtained at 0 to 20 deg angles of attack and -3 to 3 deg angles of sideslip at Mach numbers of 6 and 10 in air and 20 in helium. Results show that stable trim capability exists at angles of attack near maximum lift-drag ratio (L/D). Both performance and stability exhibited some Mach number dependency. The vehicle was longitudinally unstable at low angles of attack but stable at angles of attack near and above maximum L/D. It was directionally unstable with positive dihedral effect. The rudder showed an inability to provide lateral-directional control, and removing the vertical tail resulted in increased directional instability. Analytical predictions of the static longitudinal aerodynamic coefficients gave relatively good comparisons with the experimental data.

Mccandless, R. S.↗
NASA NTRS1985

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗
NASA NTRS1985

Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading

Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.

Kelkar, A.↗
NASA NTRS1985

Sensitivity of optimized control systems to minor structural modifications

A procedure for checking whether small changes in a structure have the potential for significant enhancements of its optimized vibration control system is described. The first step in the procedure consists of the calculation of the sensitivity of the parameters of the optimized control system to small changes in the structural parameters. Theh second step consists of the optimization of the structural parameters to produce maximal increase in the performance of the control system with minimal change in the structure. The procedure has been demonstrated for a flexible laboratory structure controlled by several rate-feedback colocated force-actuator velocity-sensor pairs. Significant improvements in the performance of the control system were obtained with small structural modifications. Analytical predictions of such effects have also been validated experimentally.

Haftka, R. T.↗
NASA NTRS1984

Composite material technology requirements for large precision space structures

The development of dimensionally stable, precision composite structures has been recognized as a high risk technology driver in NASA's continuing large space structures research. Attempts are being made to understand the influences controlling thermal performance in such composites, and specifically in composite sandwich panels. The necessary tools for such composite panels' deployment, the experimental verification of analytical predictions, and the demonstration of technology in small scale hardware, are presently addressed.

Mcelroy, P. M.↗
NASA NTRS1985

Performance degradation of helicopter rotor in forward flight due to ice

This study addresses the analytical assessment of the degradation in the forward flight performance of the front rotor Boeing Vertol CH47D helicopter in a rime ice natural icing encounter. The front rotor disk was divided into 24 15-deg sections and the local Mach number and angle of attack were evaluated as a function of azimuthal and radial location for a specified flight condition. Profile drag increments were then calculated as a function of azimuthal and radial position for different times of exposure to icing, and the rotor performance was re-evaluated including these drag increments. The results of the analytical prediction method, such as horsepower required to maintain a specific flight condition, as a function of icing time have been generated. The method to illustrate the value of such an approach in assessing performance changes experienced by a helicopter rotor as a result of rime ice accretion is described.

Korkan, K. D.↗
NASA NTRS1985

Turbine blade and vane heat flux sensor development, phase 2

The development of heat flux sensors for gas turbine blades and vanes and the demonstration of heat transfer measurement methods are reported. The performance of the heat flux sensors was evaluated in a cylinder in cross flow experiment and compared with two other heat flux measurement methods, the slug calorimeter and a dynamic method based on fluctuating gas and surface temperature. Two cylinders, each instrumented with an embedded thermocouple sensor, a Gardon gauge, and a slug calorimeter, were fabricated. Each sensor type was calibrated using a quartz lamp bank facility. The instrumented cylinders were then tested in an atmospheric pressure combustor rig at conditions up to gas stream temperatures of 1700K and velocities to Mach 0.74. The test data are compared to other measurements and analytical prediction.

Atkinson, W. H.↗
NASA NTRS1986

Application of a linearized unsteady aerodynamic analysis to standard cascade configurations

A linearized potential flow analysis, which accounts for the effects of nonuniform steady flow phenomena on the linearized unsteady aerodynamic response to prescribed blade motions, has been applied to five cascade configurations. These include the first, fifth, eighth and ninth standard configurations proposed as a result of the Second International Symposium on Aeroelasticity in Turbomachines and a NASA Lewis flutter cascade. Selected results from this study, including comparisons between analytical predictions and the experimental measurements submitted for three of the foregoing configurations, are described. The correlation between theory and experiment for the first standard configuration (a compressor cascade operating at low Mach number and frequency) is quite good. Moreover, the predictions and measurements for the NASA Lewis cascade of symmetric biconvex airfoils show good qualitative agreement. However, wide discrepancies exist between the theoretical predictions and the experimental measurements for the fifth standard configuration (a subsonic transonic fan tip cascade). These can be partially attributed to conditions being imposed in the experiment which differ from those commonly used in unsteady aerodynamic analyses.

Verdon, J. M.↗
NASA NTRS1986

Helicopter rotor noise due to ingestion of atmospheric turbulence

A theoretical study was conducted to develop an analytical prediction method for helicopter main rotor noise due to the ingestion of atmospheric turbulence. This study incorporates an atmospheric turbulence model, a rotor mean flow contraction model and a rapid distortion turbulence model which together determine the statistics of the non-isotropic turbulence at the rotor plane. Inputs to the combined mean inflow and turbulence models are controlled by atmospheric wind characteristics and helicopter operating conditions. A generalized acoustic source model was used to predict the far field noise generated by the non-isotropic flow incident on the rotor. Absolute levels for acoustic spectra and directivity patterns were calculated for full scale helicopters, without the use of empirical or adjustable constants. Comparisons between isotropic and non-isotropic turbulence at the rotor face demonstrated pronounced differences in acoustic spectra. Turning and contraction of the flow for hover and low speed vertical ascent cases result in a 3 dB increase in the acoustic spectrum energy and a 10 dB increase in tone levels. Compared to trailing edge noise, turbulence ingestion noise is the dominant noise mechanism below approximately 30 rotor harmonics, while above 100 harmonics, trailing edge noise levels exceed turbulence ingestion noise by 25 dB.

Simonich, J. C.↗
NASA NTRS1986

Shuttle Tethered Aerothermodynamics Research Facility (STARFAC)

The Earth's atmosphere from 90 km to 200 km provides the last aerothermodynamics frontier. Present NASA programs which require but also can provide an understanding of the aerodynamics and aerothermodynamics of the free molecule and transition flows that exist at these altitudes are the Aeroassisted OTV, Entry Research Vehicle and the Tethered Satellite. Each of these programs provides a unique opportunity to do flight research in the rarefied upper atmosphere. However, the Tethered Satellite Program provides, because of its capability to obtain global, in-situ, steady state data, the greatest potential to: (1)define the performance of aerodynamic shapes as a function of environmental characteristics (free molecule, transition, slip flow regimes); (2)define the characteristics of the upper atmosphere and the global variability of properties such as composition temperature, pressure and density. Such data are required to accomplish the systematic development and verification of analytical prediction techniques required to support advance configuration designs.

Siemers, P. M.↗
NASA NTRS1985

Full load shop testing of 18,000-hp gas turbine driven centrifugal compressor for offshore platform service: Evaluation of rotor dynamics performance

The results for in-plant full load testing of a 13.4 MW (18000 HP) gas turbine driven centrifugal compressor are presented and compared to analytical predictions of compressor rotor stability. Unique problems from both oil seals and labyrinth gas seals were encountered during the testing. The successful resolution of these problems are summarized.

Kirk, R. G.↗
NASA NTRS1986

Condensation heat transfer under a microgravity environment

A description of the condensation heat transfer process in microgravity is given. A review of the literature is also reported. The most essential element of condensation heat transfer in microgravity is the condensate removal mechanism. Two mechanisms for condensate removal are analyzed by looking into two problems. The first problem is concerned with film condensation on a flat porous plate with the condensate being removed by suction at the wall. The second problem is an analytical prediction of the heat transfer coefficient for condensing annular flows with the condensate film driven by the vapor shear. It is concluded that both suction and vapor shear can effectively drain the condensate to ensure continuous operation of the condensers operated under a microgravity environment. It is recommended that zero-g flight experiments be carried out to verify the prediction made in the present report. The results contained in this report should also aid in the design of future space condensers.

Chow, L. C.↗
NASA NTRS1986

Proven, long-life hydrogen/oxygen thrust chambers for space station propulsion

The development of the manned space station has necessitated the development of technology related to an onboard auxiliary propulsion system (APS) required to provide for various space station attitude control, orbit positioning, and docking maneuvers. A key component of this onboard APS is the thrust chamber design. To develop the required thrust chamber technology to support the Space Station Program, the NASA Lewis Research Center has sponsored development programs under contracts with Aerojet TechSystems Company and with Bell Aerospace Textron Division of Textron, Inc. During the NASA Lewis sponsored program with Aerojet TechSystems, a 25 lb sub f hydrogen/oxygen thruster has been developed and proven as a viable candidate to meet the needs of the Space Station Program. Likewise, during the development program with Bell Aerospace, a 50 lb sub f hydrogen/oxygen Thrust Chamber has been developed and has demonstrated reliable, long-life expectancy at anticipated space station operating conditions. Both these thrust chambers were based on design criteria developed in previous thruster programs and successfully verified in experimental test programs. Extensive thermal analyses and models were used to design the thrusters to achieve total impulse goals of 2 x 10 to the 6th power lb sub f-sec. Test data for each thruster will be compared to the analytical predictions for the performance and heat transfer characteristics. Also, the results of thrust chamber life verification tests will be presented.

Richter, G. P.↗
NASA NTRS1986

Condensation heat transfer in a microgravity environment

In the present treatment of the condensation heat transfer process in a microgravity environment, two mechanisms for condensate removal are analyzed in light of two problems: (1) film condensation on a flat, porous plate, with condensate being removed by wall suction; and (2) the analytical prediction of the heat transfer coefficient of condensing annular flows, where the condensate film is driven by vapor shear. Both suction and vapor shear can effectively drain the condensate, ensuring continuous operation in microgravity.

Chow, L. C.↗