SEARCH · Search NASA

Results for “Primary Structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Mars Science Laboratory Drill

This drill (see Figure 1) is the primary sample acquisition element of the Mars Science Laboratory (MSL) that collects powdered samples from various types of rock (from clays to massive basalts) at depths up to 50 mm below the surface. A rotary-percussive sample acquisition device was developed with an emphasis on toughness and robustness to handle the harsh environment on Mars. It is the first rover-based sample acquisition device to be flight-qualified (see Figure 2). This drill features an autonomous tool change-out on a mobile robot, and novel voice-coil-based percussion. The drill comprises seven subelements. Starting at the end of the drill, there is a bit assembly that cuts the rock and collects the sample. Supporting the bit is a subassembly comprising a chuck mechanism to engage and release the new and worn bits, respectively, and a spindle mechanism to rotate the bit. Just aft of that is a percussion mechanism, which generates hammer blows to break the rock and create the dynamic environment used to flow the powdered sample. These components are mounted to a translation mechanism, which provides linear motion and senses weight-on-bit with a force sensor. There is a passive-contact sensor/stabilizer mechanism that secures the drill fs position on the rock surface, and flex harness management hardware to provide the power and signals to the translating components. The drill housing serves as the primary structure of the turret, to which the additional tools and instruments are attached. The drill bit assembly (DBA) is a passive device that is rotated and hammered in order to cut rock (i.e. science targets) and collect the cuttings (powder) in a sample chamber until ready for transfer to the CHIMRA (Collection and Handling for Interior Martian Rock Analysis). The DBA consists of a 5/8-in. (.1.6- cm) commercial hammer drill bit whose shank has been turned down and machined with deep flutes designed for aggressive cutting removal. Surrounding the shank of the bit is a thick-walled maraging steel collection tube allowing the powdered sample to be augured up the hole into the sample chamber. For robustness, the wall thickness of the DBA was maximized while still ensuring effective sample collection. There are four recesses in the bit tube that are used to retain the fresh bits in their bit box. The rotating bit is supported by a back-to-back duplex bearing pair within a housing that is connected to the outer DBA housing by two titanium diaphragms. The only bearings on the drill in the sample flow are protected by a spring-energized seal, and an integrated shield that diverts the ingested powdered sample from the moving interface. The DBA diaphragms provide radial constraint of the rotating bit and form the sample chambers. Between the diaphragms there is a sample exit tube from which the sample is transferred to the CHIMRA. To ensure that the entire collected sample is retained, no matter the orientation of the drill with respect to gravity during sampling, the pass-through from the forward to the aft chamber resides opposite to the exit tube.

Okon, Avi B.↗

NASA NTRS2013

Composite Crew Module (CCM) Permeability Characterization

In January 2007, the NASA Administrator chartered the NASA Engineering and Safety Center (NESC) to form an Agency team to design and build a composite crew module in 18 months in order to gain hands-on experience in anticipation that future exploration systems may be made of composite materials. One of the conclusions from this Composite Crew Module Primary Structure assessment was that there was a lack of understanding regarding the ability for composite pressure shells to contain consumable gases, which posed a technical risk relative to the use of a metallic design. After the completion of the Composite Crew Module test program, the test article was used in a new program to assess the overall leakage/permeability and identify specific features associated with high leak rates. This document contains the outcome of the leakage assessment.

Kirsch, Michael T.↗

NASA NTRS2014

Space Launch System Upper Stage Technology Assessment

The Space Launch System (SLS) is envisioned as a heavy-lift vehicle that will provide the foundation for future beyond low-Earth orbit (LEO) exploration missions. Previous studies have been performed to determine the optimal configuration for the SLS and the applicability of commercial off-the-shelf in-space stages for Earth departure. Currently NASA is analyzing the concept of a Dual Use Upper Stage (DUUS) that will provide LEO insertion and Earth departure burns. This paper will explore candidate in-space stages based on the DUUS design for a wide range of beyond LEO missions. Mission payloads will range from small robotic systems up to human systems with deep space habitats and landers. Mission destinations will include cislunar space, Mars, Jupiter, and Saturn. Given these wide-ranging mission objectives, a vehicle-sizing tool has been developed to determine the size of an Earth departure stage based on the mission objectives. The tool calculates masses for all the major subsystems of the vehicle including propellant loads, avionics, power, engines, main propulsion system components, tanks, pressurization system and gases, primary structural elements, and secondary structural elements. The tool uses an iterative sizing algorithm to determine the resulting mass of the stage. Any input into one of the subsystem sizing routines or the mission parameters can be treated as a parametric sweep or as a distribution for use in Monte Carlo analysis. Taking these factors together allows for multi-variable, coupled analysis runs. To increase confidence in the tool, the results have been verified against two point-of-departure designs of the DUUS. The tool has also been verified against Apollo moon mission elements and other manned space systems. This paper will focus on trading key propulsion technologies including chemical, Nuclear Thermal Propulsion (NTP), and Solar Electric Propulsion (SEP). All of the key performance inputs and relationships will be presented and discussed in light of the various missions. For each mission there are several trajectory options and each will be discussed in terms of delta-v required and transit duration. Each propulsion system will be modeled, sized, and judged based on their applicability to the whole range of beyond LEO missions. Criteria for scoring will include the resulting dry mass of the stage, resulting propellant required, time to destination, and an assessment of key enabling technologies. In addition to the larger metrics, this paper will present the results of several coupled sensitivity studies. The ultimate goals of these tools and studies are to provide NASA with the most mass-, technology-, and cost-effective in-space stage for its future exploration missions.

Holladay, Jon↗

NASA NTRS2014

The Living With a Star Space Environment Testbed Experiments

The focus of the Living With a Star (LWS) Space Environment Testbed (SET) program is to improve the performance of hardware in the space radiation environment. The program has developed a payload for the Air Force Research Laboratory (AFRL) Demonstration and Science Experiments (DSX) spacecraft that is scheduled for launch in August 2015 on the SpaceX Falcon Heavy rocket. The primary structure of DSX is an Evolved Expendable Launch Vehicle (EELV) Secondary Payload Adapter (ESPA) ring. DSX will be in a Medium Earth Orbit (MEO). This oral presentation will describe the SET payload.

Demonstration and Science Experiments (DSX) spacec↗

NASA NTRS2014

Further Investigation Into the Use of Laser Surface Preparation of Ti-6Al-4V Alloy for Adhesive Bonding

Adhesive bonding offers many advantages over mechanical fastening, but requires robust materials and processing methodologies before it can be incorporated in primary structures for aerospace applications. Surface preparation is widely recognized as one of the key steps to producing robust and predictable bonds. This report documents an ongoing investigation of a surface preparation technique based on Nd:YAG laser ablation as a replacement for the chemical etch and/or abrasive processes currently applied to Ti-6Al-4V alloys. Laser ablation imparts both topographical and chemical changes to a surface that can lead to increased bond durability. A laser based process provides an alternative to chemical-immersion, manual abrasion, and grit blast process steps which are expensive, hazardous, environmentally unfriendly, and less precise. In addition, laser ablation is amenable to process automation, which can improve reproducibility to meet quality standards for surface preparation. An update on work involving adhesive property testing, surface characterization, surface stability, and the effect of laser surface treatment on fatigue behavior is presented. Based on the tests conducted, laser surface treatment is a viable replacement for the immersion chemical surface treatment processes. Testing also showed that the fatigue behavior of the Ti-6Al-4V alloy is comparable for surfaces treated with either laser ablation or chemical surface treatment.

Palmieri, Frank L.↗

NASA NTRS2013

30-kW SEP Spacecraft as Secondary Payloads for Low-Cost Deep Space Science Missions

The Solar Array System contracts awarded by NASA's Space Technology Mission Directorate are developing solar arrays in the 30 kW to 50 kW power range (beginning of life at 1 AU) that have significantly higher specific powers (W/kg) and much smaller stowed volumes than conventional rigid-panel arrays. The successful development of these solar array technologies has the potential to enable new types of solar electric propulsion (SEP) vehicles and missions. This paper describes a 30-kW electric propulsion vehicle built into an EELV Secondary Payload Adapter (ESPA) ring. The system uses an ESPA ring as the primary structure and packages two 15-kW Megaflex solar array wings, two 14-kW Hall thrusters, a hydrazine Reaction Control Subsystem (RCS), 220 kg of xenon, 26 kg of hydrazine, and an avionics module that contains all of the rest of the spacecraft bus functions and the instrument suite. Direct-drive is used to maximize the propulsion subsystem efficiency and minimize the resulting waste heat and required radiator area. This is critical for packaging a high-power spacecraft into a very small volume. The fully-margined system dry mass would be approximately 1120 kg. This is not a small dry mass for a Discovery-class spacecraft, for example, the Dawn spacecraft dry mass was only about 750 kg. But the Dawn electric propulsion subsystem could process a maximum input power of 2.5 kW, and this spacecraft would process 28 kW, an increase of more than a factor of ten. With direct-drive the specific impulse would be limited to about 2,000 s assuming a nominal solar array output voltage of 300 V. The resulting spacecraft would have a beginning of life acceleration that is more than an order of magnitude greater than the Dawn spacecraft. Since the spacecraft would be built into an ESPA ring it could be launched as a secondary payload to a geosynchronous transfer orbit significantly reducing the launch costs for a planetary spacecraft. The SEP system would perform the escape from Earth and then the heliocentric transfer to the science target.

Dawn spacecraft↗

NASA NTRS2015

Ames Infusion Stories for NASA Annual Technology Report: Nano Entry System for CubeSat-Class Payloads

The Nano Entry System for CubeSat-Class Payloads led to the development of the Nano-Adaptable Deployable Entry and Placement Technology ("Nano-ADEPT"). Nano-ADEPT is a mechanically deployed entry, descent, and landing (EDL) system that stows during launch and cruise (like an umbrella) and serves as both heat shield and primary structure during EDL. It is especially designed for small spacecraft where volume is a limiting constraint.

Smith, Brandon↗

NASA NTRS2014

Adaptable Deployable Entry & Placement Technology (ADEPT) for Cubesat Delivery to Mars Surface

The Adaptable, Deployable Entry and Placement Technology (ADEPT), uses a mechanical skeleton to deploy a revolutionary carbon fabric system that serves as both heat shield and primary structure during atmospheric entry. The NASA ADEPT project, currently funded by the Game Changing Development Program in STMD is currently focused on 1m class hypersonic decelerators for the delivery of very small payloads ( 5 kg) to locations of interest in an effort to leverage low-cost platforms to rapidly mature the technology while simultaneously delivering high-value science. Preliminary mission design and aerothermal performance testing in arcjets have shown the ADEPT system is quite capable of safe delivery of cubesats to Mars surface. The ability of the ADEPT to transit to Mars in a stowed configuration (similar to an umbrella) provides options for integration with the Mars 2020 cruise stage, even to consider multiple ADEPTs. System-level test campaigns are underway for FY15 execution or planning for FY16. These include deployment testing, wind tunnel testing, system-level arc jet testing, and a sounding rocket flight test. The goal is system level maturation (TRL 6) at a 1m class Mars design reference mission configuration.

3D Woven↗

NASA NTRS2015

Characterization of Hybrid CNT Polymer Matrix Composites

Carbon nanotubes (CNTs) have been studied extensively since their discovery and demonstrated at the nanoscale superior mechanical, electrical and thermal properties in comparison to micro and macro scale properties of conventional engineering materials. This combination of properties suggests their potential to enhance multi-functionality of composites in regions of primary structures on aerospace vehicles where lightweight materials with improved thermal and electrical conductivity are desirable. In this study, hybrid multifunctional polymer matrix composites were fabricated by interleaving layers of CNT sheets into Hexcel® IM7/8552 prepreg, a well-characterized toughened epoxy carbon fiber reinforced polymer (CFRP) composite. The resin content of these interleaved CNT sheets, as well as ply stacking location were varied to determine the effects on the electrical, thermal, and mechanical performance of the composites. The direct-current electrical conductivity of the hybrid CNT composites was characterized by in-line and Montgomery four-probe methods. For [0](sub 20) laminates containing a single layer of CNT sheet between each ply of IM7/8552, in-plane electrical conductivity of the hybrid laminate increased significantly, while in-plane thermal conductivity increased only slightly in comparison to the control IM7/8552 laminates. Photo-microscopy and short beam shear (SBS) strength tests were used to characterize the consolidation quality of the fabricated laminates. Hybrid panels fabricated without any pretreatment of the CNT sheets resulted in a SBS strength reduction of 70 percent. Aligning the tubes and pre-infusing the CNT sheets with resin significantly improved the SBS strength of the hybrid composite To determine the cause of this performance reduction, Mode I and Mode II fracture toughness of the CNT sheet to CFRP interface was characterized by double cantilever beam (DCB) and end notch flexure (ENF) testing, respectively. Results are compared to the control IM7/8552 laminate.

Grimsley, Brian W.↗

NASA NTRS2016

Properties of Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Matrix Composites

For aircraft primary structures, carbon fiber reinforced polymer (CFRP) composites possess many advantages over conventional aluminum alloys due to their light weight, higher strength- and stiffness-to-weight ratios, and low life-cycle maintenance costs. However, the relatively low electrical and thermal conductivities of CFRP composites fail to provide structural safety in certain operational conditions such as lightning strikes. Carbon nanotubes (CNT) offer the potential to enhance the multi-functionality of composites with improved thermal and electrical conductivity. In this study, hybrid CNT/carbon fiber (CF) polymer composites were fabricated by interleaving layers of CNT sheets with Hexcel® IM7/8852 prepreg. Resin concentrations from 1 wt% to 50 wt% were used to infuse the CNT sheets prior to composite fabrication. The interlaminar properties of the resulting hybrid composites were characterized by mode I and II fracture toughness testing. Fractographical analysis was performed to study the effect of resin concentration. In addition, multi-directional physical properties like thermal conductivity of the orthotropic hybrid polymer composite were evaluated.

Cano, Roberto J.↗

NASA NTRS2016

Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Composites

For aircraft primary structures, carbon fiber reinforced polymer (CFRP) composites possess many advantages over conventional aluminum alloys due to their light weight, higher strengthand stiffness-to-weight ratio, and low life-cycle maintenance costs. However, the relatively low electrical and thermal conductivities of CFRP composites fail to provide structural safety in certain operational conditions such as lightning strikes. Despite several attempts to solve these issues with the addition of carbon nanotubes (CNT) into polymer matrices, and/or by interleaving CNT sheets between conventional carbon fiber (CF) composite layers, there are still interfacial problems that exist between CNTs (or CF) and the resin. In this study, hybrid CNT/CF polymer composites were fabricated by interleaving layers of CNT sheets with Hexcel® IM7/8852 prepreg. Resin concentrations from 1 wt% to 50 wt% were used to infuse the CNT sheets prior to composite fabrication. The interlaminar properties of the resulting hybrid composites were characterized by mode I and II fracture toughness testing (double cantilever beam and end-notched flexure test). Fractographical analysis was performed to study the effect of resin concentration. In addition, multi-directional physical properties like thermal conductivity of the orthotropic hybrid polymer composite were evaluated. Interleaving CNT sheets significantly improved the in-plane (axial and perpendicular direction of CF alignment) thermal conductivity of the hybrid composite laminates by 50 - 400%.

Kang, Jin Ho↗

NASA NTRS2016

Tuned Chamber Core Panel Acoustic Test Results

This report documents acoustic testing of tuned chamber core panels, which can be used to supplement the low-frequency performance of conventional acoustic treatment. The tuned chamber core concept incorporates low-frequency noise control directly within the primary structure and is applicable to sandwich constructions with a directional core, including corrugated-, truss-, and fluted-core designs. These types of sandwich structures have long, hollow channels (or chambers) in the core. By adding small holes through one of the facesheets, the hollow chambers can be utilized as an array of low-frequency acoustic resonators. These resonators can then be used to attenuate low-frequency noise (below 400 Hz) inside a vehicle compartment without increasing the weight or size of the structure. The results of this test program demonstrate that the tuned chamber core concept is effective when used in isolation or combined with acoustic foam treatments. Specifically, an array of acoustic resonators integrated within the core of the panels was shown to improve both the low-frequency absorption and transmission loss of the structure in targeted one-third octave bands.

Schiller, Noah H.↗

NASA NTRS2017

New Stagnation Arc Jet Model Design for Testing ADEPT 3-D Carbon Cloth

The ADEPT concept has been considered as an entry, descent and landing system to enable Human Mars class missions. Ground rules for the Mars studies required aerocapture, orbit, and then entry. The design utilizes a 3-D woven carbon cloth fabric as both heatshield and primary structure and design guidelines required 6 layers remaining after all entry events. The peak heating predicted for the ADEPT carbon cloth was 35 Wcm2 and resulting temperatures were predicted to be 1400K. Predictions for carbon mass loss were performed using equilibrium thermochemistry, which is only accurate for T2000K. Carbon oxidation is kinetically controlled at T2000K, and mass loss drops off considerably from equilibrium values. Design of the cloth thickness and mass would be significantly reduced if kinetics were considered. This effort was to design a stagnation test article design that could be used in the AHF with varying levels of oxygen where the results could be used to develop an engineering model to describe the recession rate of the carbon as a function of the partial pressure of monotomic oxygen.

carbon cloth↗

NASA NTRS2018

Pterodactyl: Integrated Control Design for Precision Targeting of Deployable Entry Vehicles

Deployable Entry Vehicles (DEVs) enable in-situ scientific exploration at destinations with atmospheres across the solar system. Because they stow in a compact form and deploy only when ready to enter the atmosphere, DEVs relax the volume constraint imposed by rigid aeroshells. This work seeks to do for a DEV what the Wright Brothers did to propel modern day aviation: develop the guidance and control (G&C) methods that will make maneuvering and precision landing of DEV a reality. The Pterodactyl project objective is to deliver an integrated G&C methodology for a DEV, based on a detailed analysis that utilizes a Multi-disciplinary, Design, Analysis and Optimization (MDAO) framework. The current state-of-the-art for blunt body entry, G&C is rooted in the precision landing of vehicles such as Mars Science Laboratory (MSL) and Apollo, which used a propulsive reaction control system (RCS) to steer. Recent research has taken a particular interest in non-propulsive control for DEVs, including direct force control (angle of attack modulation via control surfaces or mass movement) and drag modulation (discrete change in ballistic coefficient). Using the MDAO framework that includes a guidance and control model to explore multiple control concepts for a DEV will shed light on the best design approach for these vehicles. In Pterodactyl, we will complete this study for a novel DEV concept, and then we will fabricate a functional prototype to help validate the design. The project is expected to down-select to a final control architecture by the end of 2018, and complete fabrication of the prototype by the end of 2019.The DEV chosen for detailed study in this project is the Adaptable Deployable Entry and Placement Technology (ADEPT). ADEPT uses a revolutionary 3D-woven carbon fabric that is foldable, can serve as primary structure, and can survive the extreme heating environment of atmospheric entry. The specific configuration of ADEPT under investigation is called Lifting Nano-ADEPT (LNA). LNA is designed for secondary payloads missions that require precision landing either for scientific objectives at a target destination or for payload recovery at Earth.The MDAO framework being created through this research, called COBRA-Pt (Composite Beam Roll-Up Solar Array-Prototype), will combine three critical elements of the system design: a guidance algorithm with Monte Carlo, a parametric control model, and vehicle geometry details. Novel control models being studied are deployable aerodynamic surfaces as well as shape morphing. These concepts will be compared at the system level with a more traditional propulsive RCS by comparing several key performance parameters. Upon completion of the design study, a functional prototype of LNA will be fabricated that will include the integration of guidance software and relevant control actuators. We expect this study will provide critical data that could feed into the development of an Earth-based flight test of LNA. The COBRA-Pt framework will provide a modular system by which to study any DEV concept in any atmosphere.

Smith, Brandon↗

NASA NTRS2017

Device for Temporal Measurement of Loads in Parachute Suspension Systems

In order to understand the distribution of loads in parachutes, the NASA Low Density Supersonic Decelerators (LDSD) project developed a wireless instrument to measure loads in the parachute suspension lines. The load cells are titanium links that are connected in the primary structural load path of the parachute system. Strain gages measure the elongation of the links and an onboard data acquisition system records the data to ash memory. The load cells have onboard power, and include a radio transceiver that is used to receive timing information. The load cells are designed to be interfaced with cordage, packed in a parachute bag, and deployed with a standard parachute deployment. The devices are triggered passively during the deployment of the parachute. Prototype devices with a mass of 100 grams and a load capability of 16,000 lbs were built as a proof of concept.

Brandeau, Erich J.↗

NASA NTRS2019

Common Habitat for Long Duration Transit and Surface Operations

This concept is based on the Skylab II concept, which proposes using a SLS propellant tank as the primary structure of a habitat. Common Habitat takes this a step further, proposing an interior architecture that is equally viable as a lunar surface hab, transit hab, and Mars surface hab, thus enabling a single development to support all three long duration habitat roles. Common Habitat has been pursued by the PI and co-investigators at MSFC and other centers in a spare time / funding available basis, often with heavy student intern support. Student resources have developed preliminary concepts, but these models must be refined to reflect accurate vehicle subsystems, utilities, stowage, workstations, and other crew systems. This investigation applies NASA civil servant and contractor expertise to correct errors in the most recent student concepts in order to prepare them for future human-in-the-loop evaluations to determine the most viable configuration for a Common Habitat. In prior studies there was never an opportunity to trade both crew size and internal orientation. Prior work has been a series of point designs with inconsistent design constraints, making apples to apples comparisons impossible. The most recent student work produced CAD models of four habitat variants for future use in a trade study, but the student products contain model construction and geometry errors, inaccurate subsystems design and placement, and unrealistic structural elements and outfitting. These must be corrected before the models can be moved into a VR environment for humanin- the-loop testing. Through consultation with SMEs throughout the Agency, the fidelity of these designs will be upgraded to a level of quality sufficient to make a comparative analysis of crew size sensitivity and internal orientation. The product of this activity is four upgraded CAD models, each reflecting a different configuration of the Common Habitat. One is a horizontal configuration using the full length of the SLS LOX tank. One is a vertical configuration using the same tank dimensions. The third is a horizontal configuration using a truncated SLS LOX tank (half the barrel length). The fourth is a vertical configuration of the half-length SLS LOX tank.

Howard, Robert L.↗

NASA NTRS2019

Common Habitat for Long Duration Transit and Surface Operations

Howard, Robert L.↗

NASA NTRS2020

Development of an Aeroservoelastic Model for Gust Load Alleviation of the NASA Common Research Model Wind Tunnel Experiment

As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Cramer, Nick↗