Search NASA⌕ Search

SEARCH · Search NASA

Results for “SIDESLIPPING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

An analytical study of the response of a constant-attitude aircraft to atmospheric turbulence

A light airplane equipped with an automatic control system which drives large wing flaps and the stabilator so as to produce a constant pitch attitude in all flight modes was analyzed for its response to a specific gust. The aircraft was also equipped with a bank-angle steering, zero sideslip automatic control system which was studied for its effectiveness in suppressing a specific lateral gust. The gusts were assumed to be comprised of 200 lateral and 400 vertical sinusoids. Each was used to excite the controlled aircraft and the time response to the sum of all sinusoids was plotted. The assumption was that the gust may be treated as stationary in space but variable in time rather than the reverse. Results indicate that such a control system can suppress vertical gusts up to the limit of control authority. Either the lateral accelerations or the yawing velocity response to lateral gusts can be suppressed with this system but not both simultaneously.

Smetana, F. O.↗
NASA NTRS1973

Aircraft control system

An aircraft control system is described which is particularly suited to rotary wing aircraft. Longitudinal acceleration and course rate commands are derived from a manual control stick to control translational velocity of the aircraft along a flight path. In the collective channel the manual controls provide vertical velocity commands. In the yaw channel the manual controls provide sideslip or heading rate commands at high or low airspeeds, respectively. The control system permits pilots to fly along prescribed flight paths in a precise manner with relatively low work load.

Rempfer, P. S.↗
NASA NTRS1973

Space shuttle: Preliminary pressure distributions on the 049 orbiter, orbiter in presence of H/O tank and orbiter in launch configuration

The 049 orbiter and launch configurations were tested in a trisonic wind tunnel to obtain preliminary loads information on the orbiter alone, orbiter in presence of the H/O tank and orbiter in the full launch configuration. The orbiter consisted of the baseline 049 double-delta wing, twin vertical stabilizers, seven degrees of dihedral and included abort rockets. The orbiter was mounted at minus 1.50 degree of incidence (fuselage centerline relative to H/O tank centerline) in the launch configuration. The solid rocket motors were mounted at a radial location of 21 degrees from the horizontal centerline of the H/O tank. The test was conducted over a Mach number range of 0.6 to 4.96. Nominal angle of attack and angle of sideslip ranges of minus 6 to plus 6 degrees were tested. In addition, the orbiter alone was tested over an angle of attack range of minus 6 to plus 26 degrees.

Hamilton, J. T.↗
NASA NTRS1973

Space shuttle: Pressure investigation of a space shuttle launch configuration consisting of a delta-wing orbiter and a swept-wing booster with canard and tip fans (M equals 0.6 to 1.3). Volume 1, part A: Booster data

Wind tunnel tests to determine the pressure distribution on a space shuttle launch configuration consisting of a delta wing orbiter and a swept wing booster with canard and tip fins were conducted. Pressure data were obtained for the combined orbiter and booster and for the booster alone at Mach numbers from 0.6 to 1.3, angles of attack from minus 8 degrees to plus 10 degrees, and sideslip angles from minus 6 degrees to plus 6 degrees. Pressure data were also obtained for the booster alone without canard at Mach numbers of 0.9 and 1.1. The pressure taps were distributed primarily over the booster upper surface and the orbiter lower surface.

Rampy, J. M.↗
NASA NTRS1972

Rocket ascent G-limited moment-balanced optimization program (RAGMOP)

This document describes the RAGMOP (Rocket Ascent G-limited Momentbalanced Optimization Program) computer program for parametric ascent trajectory optimization. RAGMOP computes optimum polynomial-form attitude control histories, launch azimuth, engine burn-time, and gross liftoff weight for space shuttle type vehicles using a search-accelerated, gradient projection parameter optimization technique. The trajectory model available in RAGMOP includes a rotating oblate earth model, the option of input wind tables, discrete and/or continuous throttling for the purposes of limiting the thrust acceleration and/or the maximum dynamic pressure, limitation of the structural load indicators (the product of dynamic pressure with angle-of-attack and sideslip angle), and a wide selection of intermediate and terminal equality constraints.

Lyons, J. T.↗
NASA NTRS1973

Results of investigations on a 0.0405 scale model PRR version of the NR-SSV orbiter in the North American Aeronautical Laboratory low speed wind tunnel

Experimental aerodynamic investigations were conducted in a low speed wind tunnel on a scale model space shuttle vehicle (SSV) orbiter. The purpose of the test was to investigate the longitudinal and lateral-directional aerodynamic characteristics of the space shuttle orbiter. Emphasis was placed on model component, wing-glove, and wing-body fairing effects, as well as elevon, aileron, and rudder control effectiveness. Angles of attack from - 5 deg to + 30 deg and angles of sideslip of - 5 deg, 0 deg, and + 5 deg were tested. Static pressures were recorded on base, fuselage, and wing surfaces. Tufts and talc-kerosene flow visualization techniques were also utilized. The aerodynamic force balance results are presented in plotted and tabular form.

Kingsland, R. B.↗
NASA NTRS1973

Results of investigations on a 0.0405 scale model ATP version of the NR-SSV orbiter in the North American Aeronautical Laboratory low speed wind tunnel

Experimental aerodynamic investigations were conducted on a scale model space shuttle vehicle (SSV) orbiter. The purpose of the test was to investigate the longitudinal and lateral-directional aerodynamic characteristics. Emphasis was placed on model component, wing-glove, and wing-body fairing effects, as well as elevon, aileron, and rudder control effectiveness. Angles of attack from - 5 deg to + 30 deg and angles of sideslip from - 5 deg to + 10 deg were tested. Static pressures were recorded on base, fuselage, and wing surfaces. Tufts and talc-kerosene flow visualization techniques were also utilized. The aerodynamic force balance results are presented in plotted and tabular form.

Mennell, R.↗
NASA NTRS1973

Space shuttle: An investigation of the load distribution over the SRB and external tank of a 0.004 scale model of the 049 space shuttle launch configuration

A study was conducted in a trisonic wind tunnel to determine the load distribution over the external tank and solid rocket boosters of the space shuttle launch configuration. The external tank was sting-supported and the solid rocket boosters and orbiter were mounted directly on the external tank. The external tank was, instrumented with 152 pressure orifices and the solid rocket boosters contained 78 orifices. The pressure data were obtained for various combinations of the three geometric components as the gap size between the external tank and the solid rocket boosters, angle of attack, and angle of sideslip were varied. Mach numbers ranged from 0.8 to 1.96.

Lott, R. A.↗
NASA NTRS1973

Aerodynamic effects of five lift-fan pod arrangements on an unpowered V/STOL transport model

An investigation was conducted in the Langley V/STOL tunnel to determine the effect of longitudinally oriented wing-mounted pods on the longitudinal and lateral aerodynamic characteristics in the cruise flight condition of a high-wing V/STOL transport model. Five pod arrangements were tested - three configurations with in-line pods at 20, 40, or 60 percent semispan and two split pod configurations with rear pods at 20 percent semispan and front pods at 40 or 60 percent semispan. In general, addition of the pods to the model decreased the stability, increased the lift-curve slope, and alleviated the abrupt stall of the basic model. The configuration with pods at 20 percent semispan had an abrupt instability at 10 deg angle of attack, All the configurations had lateral stability at sideslip angles from 5 to -5 deg. Very little difference in results existed between the configurations with pods at 40 and 60 percent semispan. Of the split pod configurations, the configuration with front pods at 40 percent semispan offered the best trimmed lift and lift-induced drag characteristics at high angles of attack. The configuration with in-line pods at 40 or 60 percent semispan provided the best cruise characteristics of all the pod configurations.

Thomas, J. L.↗
NASA NTRS1973

Local flow measurements at the inlet spike tip of a Mach 3 supersonic cruise airplane

The flow field at the left inlet spike tip of a YF-12A airplane was examined using at 26 deg included angle conical flow sensor to obtain measurements at free-stream Mach numbers from 1.6 to 3.0. Local flow angularity, Mach number, impact pressure, and mass flow were determined and compared with free-stream values. Local flow changes occurred at the same time as free-stream changes. The local flow usually approached the spike centerline from the upper outboard side because of spike cant and toe-in. Free-stream Mach number influenced the local flow angularity; as Mach number increased above 2.2, local angle of attack increased and local sideslip angle decreased. Local Mach number was generally 3 percent less than free-stream Mach number. Impact-pressure ratio and mass flow ratio increased as free-stream Mach number increased above 2.2, indicating a beneficial forebody compression effect. No degradation of the spike tip instrumentation was observed after more than 40 flights in the high-speed thermal environment encountered by the airplane. The sensor is rugged, simple, and sensitive to small flow changes. It can provide accurate imputs necessary to control an inlet.

Johnson, H. J.↗
NASA NTRS1973

Aerodynamic characteristics of a 55 deg clipped-delta-wing orbiter model at Mach numbers from 1.60 to 4.63

Wind tunnel tests to determine the supersonic aerodynamic characteristics of a delta wing space shuttle orbiter model were conducted. The model was tested at Mach numbers from 1.60 to 4.63, at nominal angles of attack from minus 2 degrees to plus 30 degrees, nominal sideslip angles of minus 4 degrees to plus 10 degrees, and Reynolds numbers from 1.8 to 2.5 times one million per foot.

Blair, A. B., Jr.↗
NASA NTRS1973

Flight-measured X-24A lifting body control surface hinge moments and correlation with wind tunnel predictions

Control-surface hinge-moment measurements obtained in the X-24A lifting body flight-test program are compared with results from wind-tunnel tests. The effects of variations in angle of attack, angle of sideslip, rudder bias, rudder deflection, upper-flap deflection, lower-flap deflection, Mach number, and rocket-engine operation on the control-surface hinge moments are presented. In-flight motion pictures of tufts attached to the inboard side of the right fin and the rudder and upper-flap surfaces are discussed.

Tang, M. H.↗
NASA NTRS1973

Wind tunnel investigation of static longitudinal and lateral characteristics of a full scale mockup of a light single engine high wing airplane

The model was a full-scale mockup of a light single-engine high-wing monoplane. Tests were made over an angle-of-attack range of -4 deg to 24 deg and over a sideslip range of plus or minus 8 deg at thrust coefficients of 0, 0.14, and 0.30. Control effectiveness and hinge moments were taken on the aileron, elevator, and rudder for a full range of deflections. Downwash measurements at the tail were obtained for the range of thrust coefficient and flap deflection.

Greer, H. D.↗
NASA NTRS1973

Subsonic aerodynamic characteristics of a space shuttle orbiter

A space shuttle orbiter has been studied in a low turbulence pressure tunnel at a Mach number of 0.25 and Reynolds numbers from 4.17 x 1 million to 29. 17 x 1 million, based model length. The angle of attack range was about -4 to 24 deg at angles of sideslip of 0 and 5 deg. Static longitudinal and lateral directional aerodynamic characteristics were obtained for elevon deflections from 0 to -20 deg. The model was longitudinally stable at all test conditions; however, depending on Reynolds number and eleven deflection angle, the model was directionally unstable for angles of attack between 9 and 17 deg. The model had a maximum trimmed lift drag ratio of about 6.25 which occured at an angle of attack of about 9 deg with an elevon deflection of -10 deg.

Ellison, J. C.↗
NASA NTRS1973

Low-subsonic aerodynamic characteristics of a 60 deg swept delta wing space shuttle orbiter

An investigation was conducted in the Langley low-turbulence pressure tunnel to determine Reynolds number effects on the low-subsonic areodynamic characteristics and longitudinal control effectiveness of a North American Rockwell phase B delta-wing orbiter concept designated 134D. The model was tested over a range of Reynolds numbers, based on body length, from 5.25 million to 29.4 million, at Mach numbers less than 0.35, at angles of attack from approximately -2 to 28, and at angles of sideslip of 0 and -6.

Freeman, D. C., Jr.↗
NASA NTRS1973

Overall fluctuating pressure levels on prospective space shuttle launch configurations at Mach numbers from 0.8 to 2.2

Overall fluctuating pressure levels of seven space shuttle launch configurations are presented. The model was a 4-percent-scale space shuttle vehicle, tested in both a 11- by 11-foot transonic wind tunnel and a 9- by 7-foot supersonic wind tunnel. Mach numbers varied from 0.8 to 2.2, and the angle of attack range was from -8 deg to 8 deg at angles of sideslip of -5 deg, and 5 deg. The model configurations included both series-burn and parallel-burn configurations, two canopy configurations, two positions of the orbiter nose relative to the HO tank nose and two HO tank nose-cone angles (15 deg and 20 deg). The fluctuating pressure levels are presented in three forms.

Dods, J. B., Jr.↗
NASA NTRS1973

Supersonic aerodynamic characteristics of hypersonic low-wave-drag elliptical body-tail combinations as affected by changes in stabilizer configuration

An investigation has been made at Mach numbers from 1.50 to 4.63 to determine systematically the effects of the addition and position of outboard stabilizers and vertical- and vee-tail configurations on the performance and stability characteristics of a low-wave-drag elliptical body. The basic body shape was a zero-lift hypersonic minimum-wave-drag body as determined for the geometric constraints of length and volume. The elliptical cross section had an axis ratio of 2 (major axis horizontal) and an equivalent fineness ratio of 6.14. Base-mounted outboard stabilizers were at various dihedral angles from 90 deg to minus 90 deg with and without a single center-line vertical tail or a vee-tail. The angle of attack was varied from about minus 6 to 27 deg at sideslip angles of 0 and 5 deg and a constant Reynolds number of 4.58 x one million (based on body length).

Spencer, B., Jr.↗
NASA NTRS1973

Effect of fin planform on the aerodynamic characteristics of a wingless missile with AFT cruciform controls at Mach 1.60, 2.36, and 2.86

An investigation was made in the Langley Unitary Plan wind tunnel to determine the effects of fin planform on the static longitudinal aerodynamic characteristics of a wingless maneuvering missile configuration having cruciform, all-movable, aft control surfaces. The tests were made at Mach numbers of 1.60, 2.36, and 2.86 through an angle of attack range from about -4 to 22 deg, at an angle of sideslip of 0 deg, and at a Reynolds number of 8.2 million based on model length. The pitch-control data were obtained at model roll angles of 0 and 45 deg. Control-surface forces and moments were also measured. Four alternate fin planforms were investigated.

Trescot, C. D., Jr.↗