Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Stress concentration around circular hole in a composite material specimen representative of the X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite material was used to manufacture the X-29A forward swept wing. Observe that the usual isotropic material stress concentration factor is three. However, for composite material, it was found that the anisotropic stress concentration factor is no longer constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be drastically reduced, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor. The results predicted by the mixture rule approach were about 20 percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗

Temperature effect on stress concentration around circular hole in a composite material specimen representative of X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite was used to manufacture the X-29A forward-swept wing. It was found for composite material, that the anisotropic stress concentration is no longer a constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be reduced drastically, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor of room temperature. The results predicted by the mixture rule approach were about twenty percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of the stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗

Characterization and Modeling of Hot Deformation Behavior of a Copper-Bearing High-Strength Low-Carbon Steel Microalloyed with Nb

This study investigates hot deformation behavior of a newly developed Cu-bearing high-strength low-carbon steel microalloyed with Nb (Nb-HSLC). A computational method based on experimental data was employed to design the chemical composition of the alloy. Compression tests were carried out in the temperature range of 850-1100 °C as well as strain rates of 0.001-10 s{sup −1} using BAHR Dil 805 A/D thermo-analyzer equipment. The Arrhenius-type constitutive equations were used to model the hot working behavior of the designed steel. Effects of friction and temperature rise during deformation were corrected to obtain the actual stresses. The results showed that the peak flow stress was increased with increasing Zener–Hollomon parameter. The obtained flow curves at strain rates lower than 0.1 s{sup −1} and temperatures above 950 °C represented the typical dynamic recrystallization (DRX) behavior, while the flow curves at temperatures lower than 950 °C at all strain rates were associated with continuous strain hardening. This feature is in good agreement with the precipitation temperature range of Nb(C, N) particles, i.e., 800-1000 °C. Moreover, the flow curves showed the serrations during hot deformation at strain rates of 0.001 and 0.01 s{sup −1}, indicating that the dynamic strain aging (DSA) phenomenon occurred at low strain rates. The best fit between “peak stress” and “deformation conditions” was obtained by a hyperbolic sine-type equation (R{sup 2} = 0.993). Therefore, the average activation energy was determined as 348 kJ mol{sup −1}. The agreement between the achieved model and experimental flow data was verified using the results of additional tests at a strain rate of 5 s{sup −1}. The maximum difference between the measured and predicted “peak stresses” was calculated as 5 Mpa.

36 MATERIALS SCIENCE↗

Stress decay in an orthotropic half-plane under self-equilibrating sinusoidal loading

An elastic orthotropic half-plane subjected to sinusoidal normal loading along an entire straight edge is analyzed. Stresses are calculated for material property combinations which are representative of some unidirectional fiber reinforced composites and of (+ or - 45) (subs) laminates made from the same unidirectional materials. Plots of the stresses as functions of the distance from the loaded boundary show that they can differ greatly from their counterparts in the isotropic half-plane under the same loading. How the results impact the question of the applicability of St. Venant's principle to orthotropic materials is briefly discussed.

Fichter, W. B.↗

Water Model Tests for Semirigid Airships

The design of complicated structures often presents problems of extreme difficulty which are frequently insoluble. In many cases, however, the solution can be obtained by tests on suitable models. These model tests are becoming so important a part of the design of new engineering structures that their theory has become a necessary part of an engineer's knowledge. For balloons and airships water models are used. These are models about 1/30 the size of the airship hung upside down and filled with water under pressure. The theory shows that the stresses in such a model are the same as in the actual airship. In the design of the Army Semirigid Airship RS-1 no satisfactory way was found to calculate the stresses in the keel due to the changing shape of the bag. For this purpose a water model with a flexible keel was built and tested. This report gives the theory of the design, construction, and testing of such a water model.

Tuckerman, L.B.↗

Aircraft stress sequence development: A complex engineering process made simple

Development of stress sequences for critical aircraft structure requires flight measured usage data, known aircraft loads, and established relationships between aircraft flight loads and structural stresses. Resulting cycle-by-cycle stress sequences can be directly usable for crack growth analysis and coupon spectra tests. Often, an expert in loads and spectra development manipulates the usage data into a typical sequence of representative flight conditions for which loads and stresses are calculated. For a fighter/trainer type aircraft, this effort is repeated many times for each of the fatigue critical locations (FCL) resulting in expenditure of numerous engineering hours. The Aircraft Stress Sequence Computer Program (ACSTRSEQ), developed by Southwest Research Institute under contract to San Antonio Air Logistics Center, presents a unique approach for making complex technical computations in a simple, easy to use method. The program is written in Microsoft Visual Basic for the Microsoft Windows environment.

Schrader, K. H.↗

Pressure and tension effects on mechanical properties of ZrAl{sub 2}

Structural, elastic, thermodynamic of ZrAl{sub 2} under pressure, ideal strength and deformation mode under tension are investigated by the first-principles method. The calculated structural parameters at zero pressure are in consistent with experiments. Under pressure, elastic constants and their pressure dependence are obtained using the static finite strain technique. ZrAl{sub 2} exhibits lower elastic anisotropy. The linear thermal expansion coefficient shows greater effects of temperature at lower pressure. The ideal tensile have been investigated by stress–strain calculations. Finally, the microscopic mechanism that determines the structural stability is studied using the results of electronic structure calculations. We propose that the weakening of Zr-Zr leads to the significant change of stress–strain curve at strain ∼0.27, and the breaking of Zr{sub 2}-Zr{sub 3} leads to the structural instability of ZrAl{sub 2} under large tensile strains.

36 MATERIALS SCIENCE↗

Core stress distribution of phase shifting multimode polymer optical fiber

Poly-(methyl methacrylate-co-benzyl methacrylate) polarization-maintaining optical fibers are known for their high response to normal stress. In this report, responses to higher stress levels up to 0.45 MPa were investigated. The stress amplitude and direction in the fiber cross section were calculated and analyzed with a coincident mode-field obtained from the near-field pattern. The stress amplitude varies significantly in the horizontal direction and is considered to create multiple phases, explaining the measurement results. To investigate possible permanent deformation, the core yield point profile was analyzed. Although it largely exceeds the average applied stress, the calculated stress distribution indicates that the core could partially experience stress that exceeds the yield point.

36 MATERIALS SCIENCE↗

Geomechanical simulation of the stress tensor rotation caused by injection of cold water in a deep geothermal reservoir

We present a three-dimensional thermohydromechanical numerical study of the evolution and distribution of the stress tensor within the northwest part of The Geysers geothermal reservoir (in California), including a detailed study of the region around one injection well from 2003 to 2012. Initially, after imposing a normal faulting stress regime, we calculated local changes in the stress regime around injection wells. Our results were compared with previously published studies in which the stress state was inferred from inverting the focal plane mechanism of seismic events. Our main finding is that changes in stress tensor orientation are caused by injection-induced progressive cooling of the reservoir, as well as by the seasonal variations in injection rate. Because of the gravity flow and cooling around a liquid zone formed by the injection, the vertical stress reduction is larger and propagates far below the injection well. At the same time, the horizontal stress increases, mostly because of stress redistribution below and above the cooling area. These two phenomena cause the rotation of the stress tensor and the appearance of a strike-slip regime above, inside, and below the cooling area. The cooling and the associated rotation of the stress regime can play a significant role in the observed long-term deepening of the microseismicity below active injection wells.

58 GEOSCIENCES↗

Effects of edge-seal design on the mechanical and thermal performance of vacuum-insulated glazing

Although vacuum-insulated glazing (VIG) has been proposed as a promising solution towards developing energy-efficient buildings, VIGs have not become popular in the market due to several technical challenges including the complexity of the fabrication process. In particular, the edge-seal is a key component that significantly affects the thermal insulation and mechanical performance, and the development of edge-seal with adequate thermal insulation, mechanical strength, and reasonable processing cost is essential to overcome such technical issues in VIG. For this purpose, effects of edge-seal design parameters on the VIG performance should be identified. In this research, we analyzed the edge-seal for thermal transport as well as structural stresses to study the effects, and then identified and evaluated the material mixes for the edge-seal requirements. Here, the finite element simulations showed the significance of VIG corner calculation on overall thermal transmittance and the importance of seal conductivity below 1 W/m.K. The experiments with the flexible seals with different ratios of fine glass powder demonstrated that the measured shear strength values for the seal with less than 30% glass powder were more than 10 times larger than the calculated shear stress values. Based on these simulation and experimental results, a flexible sealant was developed using a proprietary mix of ceramic materials that meets the requirements of the designed VIG edge-seal, including structural as well as thermal stress resistance and a low conductivity. Moreover, the sealant is self-curing under atmospheric conditions, and thus it does not require costly inline process of laser curing or oven baking.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Complete Status Report Documenting the Development of Friction Stir Welding for Producing a Butt Joint in Thin Wall Tubing of ODS Alloys

A challenging attempt using friction stir welding to produce a butt joint between two 1.0 mm thick plates of 14YWT was nearly successful. The modified tool pin mostly penetrated the thickness of the adjoined thin plate samples resulting in a small blunt notch on the bottom surface of the butt joint. A bend occurred in the thin plate sample due to formation of stresses from clamping the thin plate sample during FSW. The peak displacement of the bend occurred along the center line of the butt joint. The weld zone showed good microstructure mixing with some flashing mostly on the retreating side that suggested excess heat input by friction between the traveling and spinning tool pin and thin plates of 14YWT. Neutron diffraction experiments were performed on the bent sample of 14YWT to measure the residual stresses in the butt joint on the HB-2B beam line at the Neutron Residual Stress Facility at HFIR. However, the neutron scattering to background noise ratio was very low during data acquisition. Measurements of lattice strains were obtained in the rolling (RD) and normal (ND) directions but not in the extrusion direction (ED) of the thin plate sample. Unfortunately, the quality of the data was not sufficient for determining the residual stresses in the butt joint. From the previous neutron scattering experiments conducted on four hot rolled plates (R1, R2, R3 and R4) of 14YWT, the residual stresses were calculated from lattice strain data and plotted in 2-D color contour maps for ED, RD and ND. The results showed variations in the magnitude and spatial position of residual stresses in the microstructure of the four plates. The magnitude in residual stresses in ED and RD increased gradually with increasing rolling deformation for R1 (50%) to R2 (76%), followed by larger increases in R3 (89%) and R4 (95%). The maximum peaks in residual stresses for R4 was ~710-730 MPa in ED and RD. The residual stresses in ND were below ~300 MPa for each of the 4 rolled plates, with a maximum residual stress in R4 (95%) of ~400 MPa. These results indicated that significant residual stresses representing ~57% of the yield stress of 14YWT (SM13) had accumulated in the 14YWT plate after hot rolling to the 1 mm thickness, which was used in the FSW experiments. The microstructure analysis of the 1.0 mm thick plate of 14YWT containing the butt joint produced by FSW revealed significant changes in the grain structure and texture between the unaffected zone (UZ) of the rolled plate and the butt joint weld. In the UZ, the grains were severely elongated after 95% deformation and mainly possessed the {101} texture component in the ED. Two predominant grain misorientation angles were observed: one consisting of small misorientations of <5º between highly elongated grains and the other consisting of large misorientations of >15º in pockets of small grains that might have formed by dynamic recrystallization processes during rolling of the plate at 1000ºC. The morphology and texture of grains in the heat affected zone (HAZ) were similar to those in UZ, except the grains had coarsened due to excess heat input during FSZ. A population of pores formed and the grains both coarsened and changed to isotropic morphology in the microstructure of the butt joint on both the advancing and retreating sides. The texture of grains in both regions were randomly orientated between the 3 poles {001}, {101} and {111}. The main difference in texture of grains between the advancing side and retreating side was with the misorientation angles of neighboring grains. Most of the grains in the advancing side had misorientation angles of >5º indicating that these grains experienced recrystallization. On the retreating side, areas containing larger grains showed high misorientation angles of >15º compared to areas appearing as bands of grains with misorientation angles of <5º and between 5º-15º. Numerous small pockets of grains with low misorientation angles of <5º were distributed in the microstructure among the grains showing high misorientation angles of >15º. It was determined that the grains associated with low misorientation angles contained sub-grain structures, which was consistent with both recrystallization and recovery mechanisms for grains located on the retreating side of the butt joint. These results demonstrate the complex microstructure that evolves in the microstructure of 14YWT resulting from the input of high temperatures and severe deformations during FSW.

36 MATERIALS SCIENCE↗

Variational mechanics analysis of the stresses in microdrop debond specimens

A recently derived variational mechanics analysis of stresses in single-fiber model composites has been applied to the analysis of the stresses in the microdrop debond specimen. The new analysis is more accurate than the commonly applied shear-lag or elastic-plastic analyses. The results from a sample stress state calculation suggest that interfacial failure between the fiber and the microdrop is by mode I or opening mode failure at the beginning of the microdrop. The opening mode failure is caused by a large tensile radial stress at the fiber/matrix interface. Previous analyses of microdrop debond data have been in terms of a shear strength. It is suggested that these analyses misrepresent microdrop debond results and recommend instead a failure analysis based on energy release rate and interfacial fracture toughness. A procedure for calculating the energy release rate for the growth of an interfacial crack is described.

Scheer, Robert J.↗

Probing the properties and mechanisms of failure waves in soda-lime glass

Soda-lime glass (SLG) and other silica glasses exhibit the failure wave phenomenon under shock compression. The mechanism responsible for this peculiar behavior of glasses is still unresolved. In this study, a series of plate impact experiments was performed at three different impact stresses of 6.4, 8.3, and 10.8 GPa to better understand the mechanisms underlying the failure wave phenomenon. Specifically, spall experiments were conducted to probe the speed and existence of failure waves at different stresses in SLG. A layered glass target was used to probe the possibility of a “renucleation” of the wave at the SLG–SLG interface. When it existed, the failure wave was inferred to propagate at a speed of 1.3 km/s. However, it was observed that the failure wave phenomenon ceases to exist for impact stresses higher than 10 GPa. In experiments with a 6.4 GPa impact stress, the peak free surface velocity was significantly less than what is predicted by stress-Hugoniot calculations. This velocity deficit and other important features of the measured free surface velocity profiles were simulated using finite element analysis by incorporating an abrupt densification of SLG at a critical stress in the equation of state. Furthermore, this densification feature is similar to what would be expected of a phase transition. Although unable to unambiguously reveal the mechanism causing the failure wave phenomenon, the results of the present work clearly indicate that the failure wave causes a secondary compression and densification in SLG.

36 MATERIALS SCIENCE↗

Prediction of continuous porosity gradients in ceramics using ZnO as a model material

Materials with gradient microstructures have a wide range of applications such as cutting tools, armor, and electronic devices. However, it is difficult to predict and control the gradient microstructure during processing. In the present work, a continuous porosity gradient was successfully achieved in ZnO material via spark plasma sintering with a large induced thermal gradient. The porosity is overestimated if isothermal prediction is applied. The current work proposed a more accurate prediction of the porosity by considering the stress-shielding effect caused by the thermal gradient. The shielding effect results from different stress states in the sample due to differential sintering: the hotter side of the specimen experiences a higher strain rate and more shrinkage while the colder side experiences a lower strain rate and less shrinkage simultaneously. Therefore, the axial strains are varied throughout the sample thickness. Using the constituent equations in advanced sintering analysis, the shield stress was calculated to be approximately 13 MPa for the viscoelastic assumption of sintering. To improve the accuracy of predicting porosity gradient, it is necessary to add a load to overcome the shield stress when the materials are sintered with a thermal gradient.

36 MATERIALS SCIENCE↗

Stress analysis of 27% scale model of AH-64 main rotor hub

Stress analysis of an AH-64 27% scale model rotor hub was performed. Component loads and stresses were calculated based upon blade root loads and motions. The static and fatigue analysis indicates positive margins of safety in all components checked. Using the format developed here, the hub can be stress checked for future application.

Hodges, R. V.↗

Stress Relaxation Related to Spontaneous Thin Film Buckling: Correlation between Finite Element Calculations and Micro Diffraction Analysis

Compressive residual stresses generated during thin film deposition may lead to undesirable film damage, such as delamination, buckling, and flaking, ultimately leading to the failure of the device employing the film. Understanding the residual stress generation and role in these damage mechanisms is necessary to preserve thin film integrity and optimize its functional properties. Thin shell theory has been used for decades to predict buckling but the results have not yet been correlated with experimental data since the techniques used to measure stress in metallic films were not able to do so at the required micron scale until recently. Micro scanning X-ray diffraction now enables the direct mapping of the local stress of metallic films. In this paper, finite element method based on thin shell theory and synchrotron X-ray micro diffraction have been used to determine stress maps of thin film buckling patterns. Calculations of the stress distribution in the metallic films have been performed taking into account the buckling geometry determined from optical measurements. Stress distributions over gold blisters and tungsten wrinkles obtained with the two techniques are in fair agreement and allow for the accurate determination of the stress relaxation profile from the bottom to the top of the buckling, validating the thin shell theory model.

36 MATERIALS SCIENCE↗

Non-uniform Stress-free Strains in a Spherically Symmetrical Nano-sized Particle and Its Applications to Lithium-ion Batteries

The stress-free strain originated from local chemical composition and phase transformation can significantly alter the microstructures of materials; and then affect their properties. In this paper, we developed an analytical method to calculate stress-strain field due to the non-uniform stress-free strain in a spherically symmetrical particle. Applying the method to a lithium ion (Li-ion) battery electrode, the evolution of Li-ion concentration and strain field during the lithiation process is studied. Our studies reveal that the maximum strain in the electrode generally occurs on surface of sample, and is mainly dependent on the difference of Li-ion concentration of surface and of center in sample. Decreasing the difference of Li-ion concentration can efficiently decrease the maximum strain so that cracks of electrodes can been prevented. Our analytical results provide a useful guidance for practical applications of energy storage materials.

36 MATERIALS SCIENCE↗

Dyna-Soar Bioastronautics

Dyna-Soar is a manned boost-orbit-glide vehicle. Conventional booster and guidance systems will place the glider on a course at the proper altitude and velocity with the resultant energy to accomplish the planned mission. After boost termination, the pilot verifies the course during orbit and controls the flight path during reentry, approach, and landing. The flight profiles and over-all flight regime for the Dyna-Soar's single-orbit mission will impose no new or extreme environmental hazards on the pilot. '!he environmental parameters of a normal space flight will not expose the pilot to stress magnitudes as great as pilots have experienced in the Mercury flights. Under presently planned flights, the pilot should be in an environment that is well within known human tolerances. We will present the calculated environmental stress to be imposed on the pilot in both normal and emergency conditions and the design techniques .developed to provide a cockpit that will keep the pilot well within his tolerance limits. The various primary environmental parameters will be discussed separately. The solution for each parameter will be discussed in a concurrent manner. No significance is attached to the order in which the specific parameters of the environment are considered.

Spacecraft↗