Search NASA⌕ Search

SEARCH · Search NASA

Results for “SiO2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Kinetics of low pressure CVD growth of SiO2 on InP and Si

The kinetics of low pressure CVD growth of SiO2 from SiH4 and O2 has been investigated for the case of an indirect (remote) plasma process. Homogeneous (gas phase) and heterogeneous operating ranges have been experimentally identified. The process was shown to be consistent within the heterogeneous surface-reaction dominated range of operation. A kinetic rate equation is given for growth at 14 W RF power input and 400 mtorr total pressure on both InP and Si substrates. The process exhibits an activation energy of 8.4 + or - 0.6 kcal/mol.

Iyer, R.↗

Molecular dynamics of liquid SiO2 under high pressure

The molecular dynamics of pure SiO2 liquids was investigated up to pressures of 20 GPa at 4000 K using 252, 498, 864, and 1371 particles. The results obtained suggest that the pressure-induced maxima in the self-diffusion coefficients of both oxygen and silicon are dependent on the system size. In the case of larger systems, the maximum decreases and shifts to lower pressures. Changes in the velocity autocorrelation function with increasing pressure are described. The populations of anomalously coordinated silicon and oxygen are then discussed as a function of pressure and system size.

Rustad, James R.↗

Tribological evaluation of an Al2O3-SiO2 ceramic fiber candidate for high temperature sliding seals

A test program to determine the relative sliding durability of an alumina-silica candidate ceramic fiber for high temperature sliding seal applications as described. This work represents the first reporting of the sliding durability of this material system. Pin-on-disk tests were used to evaluate the potential seal material by sliding a tow or bundle of the candidate ceramic fiber against a superalloy test disk. Friction was measured during the tests and fiber wear, indicated by the extent of fibers broken in the tow or bundle, was measured at the end of each test. Test variables studied included ambient temperatures from 25 C to 900 C, loads from 1.3 to 21.2 Newtons, and sliding velocities from 0.025 to 0.25 m/sec. In addition, the effects of fiber diameter, elastic modulus, and a pretest fiber heat treatment on friction and wear were measured. In most cases, wear increased with temperature. Friction ranged from about 0.36 at 500 C and low velocity (0.025 m/s) to over 1.1 at 900 C and high velocity (0.25 m/s). The pretest fiber heat treatment, which caused significant durability reductions for alumina-boria-silica ceramic fibers tested previously, had little effect on the alumina-silica fibers tested here. These results indicate that the alumina-silica (Al2O3-SiO2) fiber is a good candidate material system for high temperature sliding seal applications.

Dellacorte, Christopher↗

Shock-induced transformations in the system NaAlSiO4-SiO2 - A new interpretation

New internally consistent interpretations of the phases represented by the high pressure phase shock wave data for an albite-rich rock, jadeite, and nepheline in the system NaAlSiO4-SiO2, are obtained using the results of static high pressure investigations, and the recent discovery of the hollandite phase in a shocked meteorite. We conclude that nepheline transforms directly to the calcium ferrite structure, whereas albite transforms possibly to the hollandite structure. Shock Hugoniots for the other plagioclase and alkali feldspars also indicate that these transform to hollandite structures. The pressure-volume data at high pressure could alternatively represent the compression of an amorphous phase. Moreover, the shock Hugoniot data are expected to reflect the properties of the melt above shock stresses of 60-80 GPa. The third order Birch-Murnaghan equation of state parameters are given for the calcium ferrite type NaAlSiO4 and for albite-rich, orthoclase-rich, and anorthite-rich hollandites.

Sekine, Toshimori↗

Application of high-quality SiO2 grown by multipolar ECR source to Si/SiGe MISFET

A 5 nm-thick SiO2 gate was grown on an Si(p+)/Si(0.8)Ge(0.2) modulation-doped heterostructure at 26 C with an oxygen plasma generated by a multipolar electron cyclotron resonance source. The ultrathin oxide has breakdown field above 12 MV/cm and fixed charge density about 3 x 10 exp 10/sq cm. Leakage current as low as 1/micro-A was obtained with the gate biased at 4 V. The MISFET with 0.25 x 25 sq m gate shows maximum drain current of 41.6 mA/mm and peak transconductance of 21 mS/mm.

Sung, K. T.↗

Tribological evaluation of an Al2O3-SiO2 ceramic fiber candidate for high temperature sliding seals

A test program to determine the relative sliding durability of an alumina-silica candidate ceramic fiber for high temperature sliding seal applications is described. Pin-on-disk tests were used to evaluate the potential seal material by sliding a tow or bundle of the candidate ceramic fiber against a superalloy test disk. Friction was measured during the tests and fiber wear, indicated by the extent of fibers broken in the tow or bundle, was measured at the end of each test. Test variables studied included ambient temperatures from 25 to 900 C, loads from 1.3 to 21.2 N, and sliding velocities from 0.025 to 0.25 m/sec. In addition, the effects of fiber diameter and elastic modulus on friction and wear were measured. Thin gold films deposited on the superalloy disk surface were evaluated in an effort to reduce friction and wear of the fibers. In most cases, wear increased with test temperature. Friction ranged from 0.36 at 500 C and low velocity (0.025 m/sec) to over 1.1 at 900 C and high velocity (0.25 m/sec). The gold films resulted in satisfactory lubrication of the fibers at 25 C. At elevated temperatures diffusion of substrate elements degraded the films. These results indicate that the alumina-silica (Al2O3-SiO2) fiber is a good candidate material system for high temperature sliding seal applications. More work is needed to reduce friction.

Dellacorte, Christopher↗

Luminescence of Eu(3+) doped SiO2 Thin Films and Glass Prepared by Sol-gel Technology

Trivalent europium ions are an important luminophore for lighting and display. The emission of (5)D0 to (7)F2 transition exhibits a red color at about 610 nm, which is very attractive and fulfills the requirement for most red-emitting phosphors including lamp and cathode ray phosphorescence materials. Various EU(3+) doped phosphors have been developed, and luminescence properties have been extensively studied. On the other hand, sol-gel technology has been well developed by chemists. In recent years, applications of this technology to optical materials have drawn a great attention. Sol-gel technology provides a unique way to obtain homogeneous composition distribution and uniform doping, and the processing temperature can be very low. In this work, EU(3+) doped SiO2 thin films and glasses were prepared by sol-gel technology and their spectroscopic properties were investigated.

Castro, Lymari↗

Feature Profile Evolution of SiO2 Trenches In Fluorocarbon Plasmas

Etching of silicon microstructures for semiconductor manufacturing in chlorine plasmas has been well characterized. The etching proceeds in a two-part process, where the chlorine neutrals passivate the Si surface and then the ions etch away SiClx. However, etching in more complicated gas mixtures and materials, such as etching of SiO2 in Ar/C4F8, requires knowledge of the ion and neutral distribution functions as a function of angle and velocity, in addition to modeling the gas surface reactions. In order to address these needs, we have developed and integrated a suite of models to simulate the etching process from the plasma reactor level to the feature profile evolution level. This arrangement allows for a better understanding, control, and prediction of the influence of equipment level process parameters on feature profile evolution. We are currently using the HPEM (Hybrid Plasma Equipment Model) and PCMCM (Plasma Chemistry Monte Carlo Model) to generate plasma properties and ion and neutral distribution functions for argon/fluorocarbon discharges in a GEC Reference Cell. These quantities are then input to the feature scale model, Simulation of Profile Evolution by Level Sets (SPELS). A surface chemistry model is used to determine the interaction of the incoming species with the substrate material and simulate the evolution of the trench profile. The impact of change of gas pressure and inductive power on the relative flux of CFx and F to the wafer, the etch and polymerization rates, and feature profiles will be examined. Comparisons to experimental profiles will also be presented.

Hwang, Helen↗

Low-Power RIE of SiO2 in CHF3 To Obtain Steep Sidewalls

A reactive-ion etching (RIE) process has been developed to enable the formation of holes with steep sidewalls in a layer of silicon dioxide that covers a silicon substrate. The holes in question are through the thickness of the SiO2 and are used to define silicon substrate areas to be etched or to be built upon through epitaxial deposition of silicon. The sidewalls of these holes are required to be vertical in order to ensure that the sidewalls of the holes to be etched in the substrate or the sidewalls of the epitaxial deposits, respectively, also turn out to be vertical.

Turner, Tasha↗

Electron Beam Induced Luminescence of SiO2 Optical Coatings

Optical coatings of disordered thin film SiO,/SiO, samples undergoing electron beam bombardment exhibited a cathodoluminescence effect. Measurements were made of the absolute illuminance and emission spectra as functions of incident electron energy (0.2 keV to 30 keV). flux (approx. 0.1 nA/sq cm to > 100 nA/sq cm) and power (<50 nW/sq cm to > 3mW/sq cm) for coatings (approx.60 nm to approx.200 nm thick) on reflective metal substrates over a range of sample temperatures (approx.40 K to approx.400 K) and emission wavelengths (approx.260 nm to approx.5000 nm). Illuminance reached a plateau saturation intensity I(sub sat) approx. 10(exp -4)W/sq cm. scaling as [I(sub mc)/(I + I(sub mc)/I(sub sat)] as incident power I(sub mc) approached I(sub sat). Well below I(sub sat), illuminance scaled linearly with incident power for lower-energy non-penetrating radiation that deposited all of its energy in the dielectric film. At higher incident energies (> 1-5 keV) electrons penetrate the dielectric, depositing only a fraction of their energy in the dielectric film, where deposited energy scales as the ratio of film thickness to penetration range. Since electron range exhibits a peak below approx. 1 keV, the illuminance decreased with increasing energy for penetrating radiation. The temperature dependence of the illuminance. in general, increased with decreasing temperature. Changes in apparent color with temperature were also observed. Four bands in the UV/VIS/NIR range from 300 nm to 1000 nm were observed in spectral measurements; no significant luminescence was detected in a range from approx. 1000 nm to approx. 5000 nm. These different bands either increased or decreased in intensity and shifted slightly in energy with decreasing temperature. Our measurements are explained in terms of simple disordered band theory models based on atomic-scale stochastic transport of electrons in highly disordered insulating materials. The theoretical models provide a fundamental basis for understanding the dependence of cathodoluminescence on irradiation time, incident flux and energy. and sample thickness and temperature. The observed luminescence occurs when an incident high energy electron excites a valence band electron into the conduction band. Following the excitation. a complex series of transitions take place between the extended conduction states and the long-lived localized trapped states (or chromophores) associated with structural or compositional defects in the dielectric materials. Thc transport equations and models of thc spatial and energy distribution of the trapped states below the mobility edge, their occupancy, and transitions provide microscopic scale insights into this macroscopic phenomenon. Our observations and theoretical models are also compared with similar previous room temperature studies of similar SiO2 films.

Dennison, J. R.↗

Acid-Sulfate Alteration at Gusev Crater and Across Mars: High-SiO2 Residues and Ferric Sulfate Precipitates

The Mars Exploration Rover Spirit ended its mission in Gusev crater on sol 2210 after it had become stuck in a deposit of fined-grained and sulfate rich soil with dust covered solar panels unfavorably pointed toward the sun. Final analysis of remaining data from Spirit's Moessbauer spectrometer (Fe redox and mineralogy) for sols 1529 through 2071 is now complete. We focus here on chemical (APXS) and MB data for targets having high-SiO2 or high-SO3 and process link the targets through mixing and geochemical modelling to an acid-sulfate system centered at Home Plate, which is considered to be a hydrovolcanic complex.

Morris, R. V.↗

Thermochemistry of CaO-MgO-Al2O3-SiO2 (CMAS) and Advanced Thermal and Environmental Barrier Coating Systems

CaO-MgO-Al2O3-SiO2 (CMAS) oxides are constituents in a broad number of materials and minerals which have recently inferred to discussions in materials science, planetary science, geochemistry and cosmochemistry communities. In materials science, there is increasing interest in the degradation studies of thermal (TBC) and environmental (EBC) barrier coatings of gas turbines by molten CMAS. CMAS minerals usually are carried by the intake air into gas turbines, e.g. in aircraft engines, and their deposits react at high temperatures (1000C) with the coating materials. This causes degradation and accelerated failure of the static and rotating components of the turbine engines. We discuss some preliminary results of the reactions between CMAS and Rare-Earth (RE Y, Yb, Dy, Gd, Nd and Sm) oxide stabilized ZrO2 or HfO2 systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples ( 2.2 mm and 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat treated at 1310 C for 5h. Samples were characterized by differential scanning calorimetry, X-ray diffraction and cross section electron microscopy analysis.

degradation↗

High Temperature Degradation of Advanced Thermal and Environmental Barrier Coatings (TEBCs) by CaO-MgO-Al2O3-SiO2 (CMAS)

There is increasing interest in the degradation studies of thermal and environmental barrier coatings (TEBCs) of gas turbines by molten CaO-MgO-Al2O3-SiO2 (CMAS). CMAS minerals are usually referred as silica-containing sand dust and volcano ash materials that are carried by the intake air into gas turbines, e.g. aircraft engines. The low-melting deposits react at high temperatures (1000C) with the coating materials. This causes degradation and accelerated coating failure of the static and rotating components of the turbine engines. We discuss some preliminary results of the reactions between CMAS and Rare-Earth (RE Y, Yb, Dy, Gd, Nd and Sm) oxide stabilized ZrO2 or HfO2 systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples (outer diameter 4.7 mm, wall thickness 0.76 mm and 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat- treated at 1310 C for 5h. Samples were characterized by differential scanning calorimetry, X-ray diffraction and cross section electron microscopy analysis.

Thermal and environmental barrier coatings↗

IR Imaging Using Arrays of SiO2 Micromechanical Detectors

In this letter, we describe the fabrication of an array of bimaterial detectors for infrared (IR) imaging that utilize SiO2 as a structural material. All the substrate material underneath the active area of each detector element was removed. Each detector element incorporates an optical resonant cavity layer in the IR absorbing region of the sensing element. The simplified microfabrication process requires only four photolithographic steps with no wet etching or sacrificial layers. The thermomechanical deflection sensitivity was 7.9 10-3 rad/K which corresponds to a noise equivalent temperature difference (NETD) of 2.9 mK. In the present work the array was used to capture IR images while operating at room temperature and atmospheric pressure and no need for vacuum packaging. The average measured NETD of our IR detector system was approximately 200 mK but some sensing elements exhibited an NETD of 50 mK.

Grbovic, Dragoslav↗

Influence of Temperature on CaO-MgO-Al2O3-SiO2 (CMAS) Corrosion on Thermal Barrier Coatings

Higher operating temperature improves the energy efficiency in gas turbine engines and thermal barrier coatings are applied to protect the blades from high temperature and dust corrosion. Dust composed by CaO-MgO-Al2O3-SiO2 (CMAS) can melt and react with pyrochlore zirconates thermal barrier materials and degrade the performance or cause failure of the coatings. This paper discusses the relationship of the reaction product and corrosion temperature.

20 FOSSIL-FUELED POWER PLANTS↗

Textural properties determined CO 2 capture of tetraethylenepentamine loaded SiO 2 nanowires from α-sepiolite

To understand the effect of porous parameters and chemical components on CO 2 capturing performance of solid state amine absorbents and their kinetic parameters, a clay mineral-based CO 2 absorbent was prepared by impregnating five different liquid amines onto SiO 2 nanowire clusters from fibrous sepiolite (Sep). Characterization was conducted by XRD, SEM, FTIR, and N 2 adsorption–desorption isotherm, CO 2 adsorption performances were measured by TGA. After acid treatment, the raw Sep mineral changed into amorphous silica nanowires, and the largest S BET of the obtained SiO 2 nanowires reached 320 m 2 /g, which was 8 times larger than the pristine mineral. Amongst the adapted amines, tetraethylenepentamine (TEPA) showed superiority in the CO 2 adsorption capacity. The optimized adsorption capacity reached 3.7 mmol/g at 75 °C from a CO 2 + N 2 mixture on a ~50 wt% TEPA loaded SiO 2 sample, and the capacity remained 3.6 mmol/g after ten circles of adsorption/desorption tests. The pore size and pore structure of the matrix, rather than the surface area, will obviously affect the adsorption ability of the product. Kinetic parameters for the CO 2 adsorption process fitted well with a fractional-order model, confirming that the CO 2 adsorption process by the solid absorbent should be a combination of both physical and chemical reactions. Results in this article provide detailed parameters for preparing and understanding these clay mineral based solid state CO 2 absorbents.

36 MATERIALS SCIENCE↗

Materials Data on SiO2 by Materials Project

Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

36 MATERIALS SCIENCE↗

Materials Data on MgFe(SiO2)2 by Materials Project

MgSiO2FeOSiO crystallizes in the orthorhombic Pmc2_1 space group. The structure is two-dimensional and consists of one FeOSiO sheet oriented in the (0, 0, 1) direction and one MgSiO2 sheet oriented in the (0, 0, 1) direction. In the FeOSiO sheet, Fe is bonded in a 3-coordinate geometry to three O atoms. There are two shorter (2.03 Å) and one longer (2.08 Å) Fe–O bond lengths. Si is bonded in a distorted trigonal non-coplanar geometry to three O atoms. There is one shorter (1.65 Å) and two longer (1.79 Å) Si–O bond length. There are two inequivalent O sites. In the first O site, O is bonded in a distorted T-shaped geometry to two equivalent Fe and one Si atom. In the second O site, O is bonded in a trigonal planar geometry to one Fe and two equivalent Si atoms. In the MgSiO2 sheet, Mg is bonded in a 3-coordinate geometry to three O atoms. There are two shorter (1.94 Å) and one longer (2.07 Å) Mg–O bond lengths. Si is bonded in a distorted trigonal non-coplanar geometry to three O atoms. There is one shorter (1.65 Å) and two longer (1.78 Å) Si–O bond length. There are two inequivalent O sites. In the first O site, O is bonded in a distorted trigonal planar geometry to two equivalent Mg and one Si atom. In the second O site, O is bonded in a trigonal planar geometry to one Mg and two equivalent Si atoms.

36 MATERIALS SCIENCE↗