Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar Array Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

The study of coronal plasma structures and fluctuations with Faraday rotation measurements

We report dual-frequency, polarimetric measurements of Faraday rotation of extragalactic radio sources viewed through the solar corona. The observations were made at the Very Large Array in 1990 during solar maximum. Of the nine observed, an excess rotation measure of -12.6 rad/sq m was detected for one source (0010+005), which was observed at an elongation of about 9 solar radii. This measurement is in fair agreement with an a priori model rotation measure of -8.6 rad/sq m estimated from coronal potential field models and the electron density model of Paetzold et al. (1992). Our measurement provides a value for the coronal magnetic field strength at 9 solar radii given a knowledge of the magnetic field sector structure, of 12.5 +/- 2.3 mG. Rotation measurements of 0010+005 were made approximately once per hour over an 11 hr period. During this interval, a slow change of about 1 rad/sq m/hr in rotation measure was detected. Although we are not absolutely certain that this drift is not unremoved ionospheric Faraday rotation, extensive analysis of data from the other sources suggests that this is not the case (Sakurai & Spangler 1994). The very long timescale for this variation argues against the agency of magnetohydrodynamics (MHD) waves, and we suggest occultation of 0010+005 by relatively static plasma structures in the corona. We filtered our rotation measure time series to search for variations on an hourly timescale, such as those reported by Hollweg et al. (1992), which could be attributed to coronal MHD waves. We were unable to detect such fluctuations and can report only an upper limit to the rms variation of 1.6 rad/sq m. This upper limit is of the same order, but slightly larger than the values typically reported by Hollweg et al. (1982). This upper limit to the rotation measure fluctuations limits the dimensionless wave amplitude (delta B)/B in the corona to be less than 0.7. Using the number, we estimate the MHD wave flux at the coronal base to be less than 1.6 x 10(exp 5) ergs/sq cm/s. This is less than the amount of wave energy flux required by wave-driven models of the solar wind. Finally, we discuss a number of ways in which such observations could be improved in the future.

Sakurai, Takayuki↗
NASA NTRS1999

Progress of the Mars Array Technology Experiment (MATE) on the '01 Lander

Future missions to Mars will rely heavily on solar power from the sun, various solar cell types and structures must be evaluated to find the optimum. Sunlight on the surface of Mars is altered by air-borne dust that fluctuates in density from day to day. The dust affects both the intensity and spectral content of the sunlight. The MATE flight experiment was designed for this purpose and will fly on the Mars 2001 Surveyor Lander as part of the Mars In-Situ Propellant Production Precursor (MIP) package. MATE will measure the performance of several solar cell technologies and characterize the Martian environment in terms of solar power. This will be done by measuring full IV curves on solar cells, direct and global insolation, temperature, and spectral content. The Lander is is scheduled to launch in April 2001 and arrive on Mars in January of 2002. The site location has not been identified but will be near the equator and last from 100 to 300 days. The intent of this of this paper is to describe and update the progress on MATE. MATE has four main objectives for its mission to Mars. First is to measure the performance of solar cells daily on the surface of Mars, this will determine the day to day fluctuations in sunlight and temperature and provide a nominal power output. Second, in addition to measuring solar cell performance, it will allow for an intercomparison of different solar cell technologies. Third, It will study the long term effects of dust on the solar cells. Fourth and last, it will characterize the mars environment as viewed by the solar cell, measuring spectrum, insolation, and temperature. Additional information is contained in the original extended abstract.

Scheiman, D. A.↗
NASA NTRS1977

SAMICS support study. Volume 1: Cost account catalog

The Jet Propulsion Laboratory (JPL) is examining the feasibility of a new industry to produce photovoltaic solar energy collectors similar to those used on spacecraft. To do this, a standardized costing procedure was developed. The Solar Array Manufacturing Industry Costing Standards (SAMICS) support study supplies the following information: (1) SAMICS critique; (2) Standard data base--cost account structure, expense item costs, inflation rates, indirect requirements relationships, and standard financial parameter values; (3) Facilities capital cost estimating relationships; (4) Conceptual plant designs; (5) Construction lead times; (6) Production start-up times; (7) Manufacturing price estimates.

Source record↗
NASA NTRS1984

Solar-array-materials passive LDEF experiment (A0171)

The objective of this experiment is to evaluate the synergistic effects of the space environment on various solar-array materials, including solar cells, cover slips with various antireflectance coatings, adhesive, encapsulants, reflector materials, substrate strength materials, mast and harness materials, structural composites, and thermal control treatments. The experiment is passive and consists of an arrangement of material specimens mounted in a 3-in.-deep peripheral tray. The effects of the space environment on the specimens will be determined by comparison of preflight and postflight measurements of mechanical, electrical, and optical properties.

Whitaker, A. F.↗
NASA NTRS1992

Construction and development of a human base on Mars

Ways in which various construction-oriented activities might be carried out on the surface of Mars are addressed, with emphasis on determining the power, mass, and manpower requirements for these activities. Attention is given to the soil mechanics of Mars, a series of guidelines and fundamental calculations for building various structures such as inflatables, foundations, and in situ material buildings, construction procedures such as laying pipe or cables and setting up solar arrays, and equipment needs and uses for a nominal base on Mars. Under the assumption of some types of construction machines, the construction time is estimated. Most of the work is shown to be completable within a reasonable time scale (10 yr or more), although some work requires impractical construction time. This work includes the covering of both rigid and inflatable habitat modules. It is suggested that alternative types of construction machines are required for this type of work.

Gwynne, Owen↗
NASA NTRS1999

Miniature Heat Transport System for Nanosatellite Technology

The scientific understanding of key physical processes between the Sun and the Earth require simultaneous measurements from many vantage points in space. Nano-satellite technologies will enable a class of constellation missions for the NASA Space Science Sun-Earth Connections. This recent emphasis on the implementation of smaller satellites leads to a requirement for development of smaller subsystems in several areas. Key technologies under development include: advanced miniaturized chemical propulsion; miniaturized sensors; highly integrated, compact electronics; autonomous onboard and ground operations; miniatures low power tracking techniques for orbit determination; onboard RF communications capable of transmitting data to the ground from far distances; lightweight efficient solar array panels; lightweight, high output battery cells; lightweight yet strong composite materials for the nano-spacecraft and deployer-ship structures. These newer smaller systems may have higher power densities and higher thermal transport requirements than seen on previous small satellites. Furthermore, the small satellites may also have a requirement to maintain thermal control through extended earth shadows, possibly up to 8 hours long. Older thermal control technology, such as heaters, thermostats, and heat pipes, may not be sufficient to meet the requirements of these new systems. Conversely, a miniature two-phase heat transport system (Mini-HTS) such as a Capillary Pumped Loop (CPL) or Loop Heat Pipe (LBP) is a viable alternative. A Mini-HTS can provide fine temperature control, thermal diode action, and a highly efficient means of heat transfer. The Mini-HTS would have power capabilities in the range of tens of watts or less and provide thermal control over typical spacecraft ranges. The Mini-HTS would allow the internal portion of the spacecraft to be thermally isolated from the external radiator, thus protecting the internal components from extreme cold temperatures during an eclipse. The Mini-HTS would transport the beat from these components to a radiator during their operational modes, and it would be shutdown during non-operational or eclipse modes. Shutdown of the Mini-HTS would be accomplished with small heaters and has been successfully demonstrated on numerous occasions, both in the lab and on flight experiments. Efforts are now underway to miniaturize two-phase heat transport systems for the Nanosatellite project, with potential application to other small satellite programs. 'ne goal of this project is to design, build, and test miniature heat transport systems (MHTS) that would demonstrate the feasibility of a small Capillary Pumped Loop (CPL) or Loop Heat Pipe (LBP).

Douglas, Donya M,↗
NASA NTRS2013

ISS-based Development of Elements and Operations for Robotic Assembly of A Space Solar Power Collector

We present a concept for an ISS-based optical system assembly demonstration designed to advance technologies related to future large in-space optical facilities deployment, including space solar power collectors and large-aperture astronomy telescopes. The large solar power collector problem is not unlike the large astronomical telescope problem, but at least conceptually it should be easier in principle, given the tolerances involved. We strive in this application to leverage heavily the work done on the NASA Optical Testbed Integration on ISS Experiment (OpTIIX) effort to erect a 1.5 m imaging telescope on the International Space Station (ISS). Specifically, we examine a robotic assembly sequence for constructing a large (meter diameter) slightly aspheric or spherical primary reflector, comprised of hexagonal mirror segments affixed to a lightweight rigidizing backplane structure. This approach, together with a structured robot assembler, will be shown to be scalable to the area and areal densities required for large-scale solar concentrator arrays.

astronomy↗
NASA NTRS1980

Multi-hundred kW solar arrays for space

A system-level approach has been applied in designing a cost-effective 300-1000 kW solar array for Low Earth Orbit (LEO) application with a mission time frame of mid-1980's. Technology investigations and performance and cost prognoses in the area of solar cells and reflector material form a key influence on array design and performance. Major tradeoffs were conducted between planar and concentrator concepts and between silicon and GaAs solar cells. Three baseline design concepts emerged: planar, low-CR concentrator (CR = 5), and high-CR concentrator (CR = 125). Combinations of these concepts with silicon and GaAs solar cells were analyzed in terms of electrical performance, thermal behavior, structural configuration, weight, stowed and deployed volume, and installation/deployment method. To identify the most cost-effective designs, a cost analysis of the candidate arrays was performed. The low-CR/GaAs array and the planar/silicon array demonstrate the greatest cost-effectiveness of the candidate arrays in terms of dollars/watt and energy life-cycle cost. Due to the high uncertainty of GaAs cell-cost prognoses, the sensitivity of the results to the GaAs cell cost is discussed.

Woodcock, W. G., III↗
NASA NTRS1986

Energetic Phenomena on the Sun: The Solar Maximum Mission Flare Workshop. Proceedings

The general objectives of the conference were as follows: (1) Synthesize flare studies after three years of Solar Maximum Mission (SSM) data analysis. Encourage a broader participation in the SMM data analysis and combine this more fully with theory and other data sources-data obtained with other spacecraft such as the HINOTORI, p78-1, and ISEE-3 spacecrafts, and with the Very Large Array (VLA) and many other ground-based instruments. Many coordinated data sets, unprecedented in their breadth of coverage and multiplicity of sources, had been obtained within the structure of the Solar Maximum Year (SMY). (2) Stimulate joint studies, and publication in the general scientific literature. The intended primary benefit was for informal collaborations to be started or broadened at the Workshops with subsequent publications. (3) Provide a special publication resulting from the Workshop.

Kundu, Mukul↗
NASA NTRS1967

Deployable solar array

Development, fabrication, and testing of deployable solar cell array for spin-oriented spacecraft applications

SPACECRAFT↗
NASA NTRS1989

Advanced Photovoltaic Solar Array program status

The Advanced Photolvoltaic Solar Array (APSA) Program is discussed. The objective of the program is to demonstrate a producible array system by the end of this decade with a beginning-of-life (BOL) specific power of 130 W/kg at 10 kW as an intermediate milestone toward the ultimate goal of 300 W/kg at 25 kW by the year 2000. The near-term goal represents a significant improvement over existing rigid panel flight arrays (25 to 45 W/kg) and the first-generation flexible blanket NASA/OAST SAFE I array of the early 1980s, which was projected to provide about 60 W/kg BOL. The prototype wing hardware is in the last stages of fabrication and integration. The current status of the program is reported. The array configuration and key design details are shown. Projections are shown for future performance enhancements that may be expected through the use of advanced structural components and solar cells.

Kurland, Richard M.↗
NASA NTRS1982

NASA space photovoltaic research and technology programs

The NASA programs for increasing conversion efficiency, reduced mass and cost, and extending operating life of photovoltaic converters and arrays and for evaluating advanced solar array concepts are outlined. Research into radiation resistance and annealing, development of thin blankets, high-power low-cost arrays, and lightweight structures for near-Earth and planetary applications are discussed.

Mullin, J. P.↗
NASA NTRS1985

Using a life-cycle-cost criterion for multi-disciplinary design studies for the Manned Space Station

A life-cycle-cost measure for the Manned Space Station is suggested which considers the mass, initial cost, aerodynamic drag, electrical power, moment, required ground support, and expected life of subsystems or components. It is proposed that this life-cycle-cost measure be considered as a criterion for design trade-off studies involving controls and structures. Calculating the related sensitivities in the optimization process is discussed and then applied to specific examples. In the first example, the reaction control system is analyzed with regard to the design of its supporting structure and selection of rocket type. Values of support beam length, structural material selection, and rocket propellant selection are determined which minimize life-cycle-cost. In the second example, the alignment of solar arrays are analyzed for efficiency with regard to generating power, their drag, and their aerodynamic moment. Alignment angles are determined which again minimize life cycle cost. It seems clear from these and other examples that the proposed criterion has value for multi-disciplinary design studies for the Manned Space Station.

Taylor, L. W.↗
NASA NTRS1985

Measurement of orbital dynamics of the OAST-1 Solar Array using recorded video images

The OAST-1 Solar Array Experiment was flown on Shuttle mission STS-41D on August 31, 1984 for NASA's Office of Aeronautics and Space Technology. It is pointed out that this was the first flight demonstration of the operation of a large solar array which was designed for multiple deployments and retractions. The array represents also a new class of very lightweight, flexible, low-frequency structures. A program was, therefore, implemented with the aim to study the structural dynamics of the array on the basis of a photogrammetric analysis of data obtained with the existing Shuttle closed circuit television (CCTV) system. The present paper has the objective to describe the experiment and its implementation, taking into account the unique process of analyzing the video data.

Miller, J. B.↗
NASA NTRS1996

Was the MSSTA 2 mission successful?

The Multi-Spectral Solar Telescope Array (MSSTA) is a rocket borne solar observatory designed to address a wide range of scientific questions relating to two aspects of the structure and dynamics of the solar atmosphere: (1) The heating and dynamics of chromospheric and coronal structures including spicules, coronal loops, bright points, and planes; and the role of the fine scale structure of the chromospheric network in the transport of mass and energy between these structures, and (2) The large scale structures of the corona, including the interface of prominences and filaments with material at coronal temperatures, the transition region structure of coronal holes and plumes, and their relationship to the solar wind. In order to address these fundamental scientific problems, the observational objective of the MSSTA is to obtain a set of high resolution spectroheliograms with the following properties: (1) Sufficiently broad spectral coverage and accurate photometry to allow modeling of structures covering the full range of temperatures observed in non-flaring chromosphere/corona, 10(exp 4) K to 10(exp 7) K; (2) Sufficient spectral resolution (lambda / delta lambda approx. 30-100) in each spectroheliogram to allow isolation of the emission from lines excited over a narrow range of temperatures; (3) To address objective (a), spatial resolution sufficient to resolve structures on the sun on a scale of 100-200 km (0.1-0.3 arc seconds); to address objective (b), images of the full disk and inner corona with resolution at least 1.0 arc second, and high sensitivity images of the extended corona (to approx. 3-4 solar radii above the limb) with resolution of approx. 3 arc seconds; for both objectives (c), direct measurements of the coronal magnetic field. (4) To access the role of non-thermal phenomena in the heating and dynamics of the chromosphere/corona interface, high resolution (lambda / delta lambda greater than 1000) spectroheliograms with spatial resolution of 1-3 arc seconds.

Spencer, Dwight C.↗
NASA NTRS1996

Plasma Properties and Magnetic Field Structure of the Solar Corona, Based on Coordinated Max '91 Observations from SERTS, the VLA, and Magnetographs

The plasma properties and magnetic field structure of the solar corona were determined using coordinated observations obtained with NASA/GSFC's Solar EUV Rocket Telescope and Spectrograph (SERTS), the Very Large Array (VLA), and Kitt Peak photospheric longitudinal magnetograms. A problem was identified with the SERTS calibration as determined from laboratory measurements. A revised calibration curve was derived by requiring that the numerous available measured line intensity ratios agreed with their respective theoretical values. Densities were derived from line intensity ratios, and active region densities were found to typically exceed quiet Sun densities by factors of only about 2. The active region density was found to remain constant across the SERTS slit, despite the fact that the emission line intensities vary significantly. This indicates that the product of the path length and the volume filling factor must vary significantly from the active region outskirts to the central core. Filling factors were derived and found to range from much less than one to nearly unity. Wavelength shifts were examined along the SERTS slit in the spatially resolved spectra, but no evidence was found for significant Doppler shifts in active region 7563 or in the quiet Sun. The numerical procedure developed by Monsignori-Fossi and Landini was used to derive the active region and quiet sun differential emission measure (DEM) from the spatially averaged spectra. A DEM was estimated for each spatial pixel in the two dimensional active region images by scaling the averaged active region DEM based upon corresponding pixel intensities of SERTS Mg IX, Fe XV, and Fe XVI images. These results, along with density measurements, were used in an IDL computer code which calculated the temperature dependence of the coronal magnetic field in each spatial pixel by minimizing the difference between the observed and calculated 20 and 6 cm microwave brightness temperatures.

Brosius, Jeffrey W.↗
NASA NTRS2011

Forward Modeling of a Coronal Cavity

We apply a forward model of emission from a coronal cavity in an effort to determine the temperature and density distribution in the cavity. Coronal cavities are long, low-density structures located over filament neutral lines and are often seen as dark elliptical features at the solar limb in white light, EUV and X-rays. When these structures erupt they form the cavity portions of CMEs The model consists of a coronal streamer model with a tunnel-like cavity with elliptical cross-section and a Gaussian variation of height along the tunnel length. Temperature and density can be varied as a function of altitude both in the cavity and streamer. We apply this model to a cavity observed in Aug. 2007 by a wide array of instruments including Hinode/EIS, STEREO/EUVI and SOHO/EIT. Studies such as these will ultimately help us understand the the original structures which erupt to become CMEs and ICMES, one of the prime Solar Orbiter objectives.

Kucera, T. A.↗