Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural engineering.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

An Energy Based Fatigue Life Prediction Framework for In-Service Structural Components

An energy based fatigue life prediction framework has been developed for calculation of remaining fatigue life of in service gas turbine materials. The purpose of the life prediction framework is to account aging effect caused by cyclic loadings on fatigue strength of gas turbine engines structural components which are usually designed for very long life. Previous studies indicate the total strain energy dissipated during a monotonic fracture process and a cyclic process is a material property that can be determined by measuring the area underneath the monotonic true stress-strain curve and the sum of the area within each hysteresis loop in the cyclic process, respectively. The energy-based fatigue life prediction framework consists of the following entities: (1) development of a testing procedure to achieve plastic energy dissipation per life cycle and (2) incorporation of an energy-based fatigue life calculation scheme to determine the remaining fatigue life of in-service gas turbine materials. The accuracy of the remaining fatigue life prediction method was verified by comparison between model approximation and experimental results of Aluminum 6061-T6. The comparison shows promising agreement, thus validating the capability of the framework to produce accurate fatigue life prediction.

33 ADVANCED PROPULSION SYSTEMS↗

Nonlinear dynamics induced in a structure by seismic and environmental loading

In this study,we show that under very weak dynamic and quasi-static deformation, that is orders of magnitude below the yield deformation of the equivalent stress strain curve (around 10 -3 ), the elastic parameters of a civil engineering structure (resonance frequency and damping) exhibit nonlinear softening and recovery. These observations bridge the gap between laboratory and seismic scales where elastic nonlinear behavior has been previously observed. Under weak seismic or atmospheric loading, modal frequencies are modified by around 1% and damping by more than 100% for strain levels between 10 -7 and 10 -4 . These observations support the concept of universal behavior of nonlinear elastic behavior in diverse systems, including granular materials and damaged solids that scale from millimeter dimensions to the scale of structures to fault dimensions in the Earth.

58 GEOSCIENCES↗

Phenyl Functionalization of Atomically Precise Graphene Nanoribbons for Engineering Inter-ribbon Interactions and Graphene Nanopores

Graphene nanoribbons (GNRs) attract a great attention from researchers due to their tunable physical properties and potential for becoming nanoscale building blocks of electronic devices. GNRs can be synthesized with atomic precision by on-surface approaches from specially designed molecular precursors. While a considerable number of ribbons with very diverse structures and properties have been demonstrated in recent years, there have been only limited examples of on-surface synthesized GNRs modified with functional groups. In this study, we designed a nanoribbon, in which the chevron GNR backbone is decorated with phenyl functionalities, and demonstrate the on-surface synthesis of these GNRs on Au(111). We show that the phenyl modification affects the assembly of the GNR polymer precursors through π-π interactions. Scanning tunneling spectroscopy of the modified GNRs on Au(111) revealed that they have a band gap of 2.50±0.02 eV, which is comparable to that of the parent chevron GNR. The phenyl functionalization leads to a shift of the band edges to lower energies, suggesting that it could be a useful tool for the GNR band structure engineering. We also investigated lateral fusion of the phenyl-modified GNRs and demonstrate that it could be used to engineer different kinds of atomically precise graphene nanopores. A similar functionalization approach could be potentially applied to other GNRs to affect their on-surface assembly, modify their electronic properties, and realize graphene nanopores with a variety of structures.

47 OTHER INSTRUMENTATION↗

Towards a Robust Sampling Approach: A Computational Review and Design

As pointed out in several other works, the estimation of the reliability of the electrical grid can not be conducted without the estimation of the stochastic phenomena of electicity demand and electricity production by variable renewable sources. Therefore, sampling procedures have become integral in the design of engineering structures and analysis. Commonly referred to as Monte Carlo uncertainty analysis or integration, the general objective of these procedures is to establish specifics about the uncertainty of an output characteristic of such an engineering system, given uncertainty about its input characteristics. These sampling procedures are applied in a context in which establishing such specifics cannot be performed through other means. Variance-reduction techniques are designed to lessen the variability among estimators to estimate statistics of those output uncertainties. Importance-sampling techniques, on the other hand, are designed to reduce the number of samples needed to estimate a particular statistic—e.g., a tail probability. The combination of these approaches can reduce the computational burden considerably for a particular estimator and statistic. Importance sampling—geared and designed as it is toward improving a particular estimator—suffers, unfortunately, from the unintended consequence of reducing the performance of other estimators in terms of their variance. The objective of this paper is to offer an alternative sampling procedure where this variance does not grow unacceptably large for a suite of estimators. Moreover, it is anticipated that, with additional knowledge of how an engineering output characteristic responds to its input characteristics, tuning parameters of the input’s sampling procedure can be set to improve the output characteristic’s estimation. This work proves the effectiveness of the suggested alternative approach. Such positive outcome will lead to a decrease of the computational burden of performing stochastic optimization of integrated energy systems (e.g., components dispatch, and portfolio composition). In particular, capturing the contribution to the overall system cost of rare and unlikely events and patterns of the electricity demand and production will become less computationally expensive. This is due to the fact that the approach demonstrated here will allow the sampling of those rare occurrences more frequently without misrepresenting their probabilistic impacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing

The Non-Metallic Gas Turbine Engine project, funded by NASA Aeronautics Research Institute, represents the first comprehensive evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. This will be achieved by assessing the feasibility of using additive manufacturing technologies to fabricate polymer matrix composite and ceramic matrix composite turbine engine components. The benefits include: 50 weight reduction compared to metallic parts, reduced manufacturing costs, reduced part count and rapid design iterations. Two high payoff metallic components have been identified for replacement with PMCs and will be fabricated using fused deposition modeling (FDM) with high temperature polymer filaments. The CMC effort uses a binder jet process to fabricate silicon carbide test coupons and demonstration articles. Microstructural analysis and mechanical testing will be conducted on the PMC and CMC materials. System studies will assess the benefits of fully nonmetallic gas turbine engine in terms of fuel burn, emissions, reduction of part count, and cost. The research project includes a multidisciplinary, multiorganization NASA - industry team that includes experts in ceramic materials and CMCs, polymers and PMCs, structural engineering, additive manufacturing, engine design and analysis, and system analysis.

Ceramics↗

Human Factors Interface with Systems Engineering for NASA Human Spaceflights

This paper summarizes the past and present successes of the Habitability and Human Factors Branch (HHFB) at NASA Johnson Space Center s Space Life Sciences Directorate (SLSD) in including the Human-As-A-System (HAAS) model in many NASA programs and what steps to be taken to integrate the Human-Centered Design Philosophy (HCDP) into NASA s Systems Engineering (SE) process. The HAAS model stresses systems are ultimately designed for the humans; the humans should therefore be considered as a system within the systems. Therefore, the model places strong emphasis on human factors engineering. Since 1987, the HHFB has been engaging with many major NASA programs with much success. The HHFB helped create the NASA Standard 3000 (a human factors engineering practice guide) and the Human Systems Integration Requirements document. These efforts resulted in the HAAS model being included in many NASA programs. As an example, the HAAS model has been successfully introduced into the programmatic and systems engineering structures of the International Space Station Program (ISSP). Success in the ISSP caused other NASA programs to recognize the importance of the HAAS concept. Also due to this success, the HHFB helped update NASA s Systems Engineering Handbook in December 2007 to include HAAS as a recommended practice. Nonetheless, the HAAS model has yet to become an integral part of the NASA SE process. Besides continuing in integrating HAAS into current and future NASA programs, the HHFB will investigate incorporating the Human-Centered Design Philosophy (HCDP) into the NASA SE Handbook. The HCDP goes further than the HAAS model by emphasizing a holistic and iterative human-centered systems design concept.

Wong, Douglas T.↗

Tackling Disorder in γ‐Ga 2 O 3

Abstract Ga 2 O 3 and its polymorphs are attracting increasing attention. The rich structural space of polymorphic oxide systems such as Ga 2 O 3 offers potential for electronic structure engineering, which is of particular interest for a range of applications, such as power electronics. γ‐Ga 2 O 3 presents a particular challenge across synthesis, characterization, and theory due to its inherent disorder and resulting complex structure–electronic‐structure relationship. Here, density functional theory is used in combination with a machine‐learning approach to screen nearly one million potential structures, thereby developing a robust atomistic model of the γ‐phase. Theoretical results are compared with surface and bulk sensitive soft and hard X‐ray photoelectron spectroscopy, X‐ray absorption spectroscopy, spectroscopic ellipsometry, and photoluminescence excitation spectroscopy experiments representative of the occupied and unoccupied states of γ‐Ga 2 O 3 . The first onset of strong absorption at room temperature is found at 5.1 eV from spectroscopic ellipsometry, which agrees well with the excitation maximum at 5.17 eV obtained by photoluminescence excitation spectroscopy, where the latter shifts to 5.33 eV at 5 K. This work presents a leap forward in the treatment of complex, disordered oxides and is a crucial step toward exploring how their electronic structure can be understood in terms of local coordination and overall structure.

36 MATERIALS SCIENCE↗

Mechanically Tunable Radiative Cooling for Adaptive Thermal Control

Passive radiative cooling is currently thefrontier technology in renewable-energy research. Interms of extraterrestrial applications, radiative cooling is a critical component to the thermalmanagement system of a spacecraft, where the extreme environment of space can cause largetemperature variations that can break and damage equipment. For terrestrial applications,nocturnal or daytime radiative cooling is expected to lead to cost-effective passive heatmanagement without the need of inefficient and costly artificial refrigeration technologies.However, most currently available radiative cooling systems cannot be changed dynamically andradiate a constant static amount of thermal power. Dynamically tunable adaptive radiativecooling systems will be a critical development to prolong the lifetime of spacecraft or improvethe efficiency of terrestrial cooling systems. Here we propose stretchable radiative coolingdesigns that can be substantially tuned by using the simple physical mechanism of mechanical strain. When their structure is stretched, the radiated power is significantly reduced. We developa modeling method that can simulate mechanical stretching combined with electromagnetic response to compute the tunable thermal emission of these new adaptive radiative coolingsystems. The presented photonically engineered structures can be used as coatings to achieveefficient adaptive thermal control of various objects in a cost-effective and environmentallyfriendly way. The proposed designs are much simpler to be realized than others found in theliterature and the best design achieves a high thermal emission power with a tunable range on theorder of 132 W/m2.

Andrew Butler↗

Indium Preferential Distribution Enables Electronic Engineering of Magnetism in FeSb 2– x In x Se 4 p-Type High-Tc Ferromagnetic Semiconductors

In this work, single-phase samples of the solid-solution series FeSb 2– x In x Se 4 (0 ≤ x ≤ 0.25) were synthesized using solid-state reaction of the elements to probe the effect of electronic structure engineering on the magnetic behavior of the p-type semiconductor, FeSb 2 Se 4 . Powder X-ray diffraction data suggest that all samples are isostructural with FeSb 2 Se 4 . Rietveld refinements of the distribution of In atoms at various metal positions indicate a preferential substitution of Sb at the M1( 4i ) position within the magnetic layer A for In concentration up to x = 0.1. FeSb 2– x In x Se 4 compositions with higher In content show the distribution of In atoms at all metal positions, except for the M3( 2d ), which is fully occupied by Fe atoms. Interestingly, the ordering of Fe atoms within the crystal structure of FeSb 2– x In x Se 4 remains essentially unaffected by the degree of substitution ( x values) and is comparable to the distribution of Fe atoms reported in FeSb 2 Se 4 . X-ray photoelectron spectroscopy confirms the oxidation states of various metal atoms In(+3), Sb(+3), Fe(+2) in the structure. Electronic transport properties indicate p-type semiconducting behavior for all samples. The electrical conductivity above 300 K first increases with In content, reaches the maximum value for x = 0.1, then decreases with further increase in In content. A reverse trend is observed for the thermopower. All samples show drastically low thermal conductivity with room temperature values ranging from 0.45 Wm –1 K –1 for x = 0 to 0.27 Wm –1 K –1 for the sample with x = 0.25. Magnetic susceptibility data suggest ferromagnetic-like behavior from 2–300 K for all samples. The magnitude of the magnetic susceptibility rapidly increases with In content, reaches a maximum for x = 0.1, and marginally decreases with further increase in In concentration. The observed surprising change in the magnetic and electronic behavior of samples with high In content ( x > 0.1) is rationalized using the concept of antiferromagnetic scattering of charge carriers at the interfaces between overlapping bound magnetic polarons from adjacent layers A and B.

36 MATERIALS SCIENCE↗

Nanostructural engineering of nitride nucleation layers for GaN substrate dislocation reduction.

With no lattice matched substrate available, sapphire continues as the substrate of choice for GaN growth, because of its reasonable cost and the extensive prior experience using it as a substrate for GaN. Surprisingly, the high dislocation density does not appear to limit UV and blue LED light intensity. However, dislocations may limit green LED light intensity and LED lifetime, especially as LEDs are pushed to higher current density for high end solid state lighting sources. To improve the performance for these higher current density LEDs, simple growth-enabled reductions in dislocation density would be highly prized. GaN nucleation layers (NLs) are not commonly thought of as an application of nano-structural engineering; yet, these layers evolve during the growth process to produce self-assembled, nanometer-scale structures. Continued growth on these nuclei ultimately leads to a fully coalesced film, and we show in this research program that their initial density is correlated to the GaN dislocation density. In this 18 month program, we developed MOCVD growth methods to reduce GaN dislocation densities on sapphire from 5 x 10{sup 8} cm{sup -2} using our standard delay recovery growth technique to 1 x 10{sup 8} cm{sup -2} using an ultra-low nucleation density technique. For this research, we firmly established a correlation between the GaN nucleation thickness, the resulting nucleation density after annealing, and dislocation density of full GaN films grown on these nucleation layers. We developed methods to reduce the nuclei density while still maintaining the ability to fully coalesce the GaN films. Ways were sought to improve the GaN nuclei orientation by improving the sapphire surface smoothness by annealing prior to the NL growth. Methods to eliminate the formation of additional nuclei once the majority of GaN nuclei were developed using a silicon nitride treatment prior to the deposition of the nucleation layer. Nucleation layer thickness was determined using optical reflectance and the nucleation density was determined using atomic force microscopy (AFM) and Nomarski microscopy. Dislocation density was measured using X-ray diffraction and AFM after coating the surface with silicon nitride to delineate all dislocation types. The program milestone of producing GaN films with dislocation densities of 1 x 10{sup 8} cm{sup -2} was met by silicon nitride treatment of annealed sapphire followed by the multiple deposition of a low density of GaN nuclei followed by high temperature GaN growth. Details of this growth process and the underlying science are presented in this final report along with problems encountered in this research and recommendations for future work.

36 MATERIALS SCIENCE↗

Robust Decision-making Applied to Model Selection

The scientific and engineering communities are relying more and more on numerical models to simulate ever-increasingly complex phenomena. Selecting a model, from among a family of models that meets the simulation requirements, presents a challenge to modern-day analysts. To address this concern, a framework is adopted anchored in info-gap decision theory. The framework proposes to select models by examining the trade-offs between prediction accuracy and sensitivity to epistemic uncertainty. The framework is demonstrated on two structural engineering applications by asking the following question: Which model, of several numerical models, approximates the behavior of a structure when parameters that define each of those models are unknown? One observation is that models that are nominally more accurate are not necessarily more robust, and their accuracy can deteriorate greatly depending upon the assumptions made. It is posited that, as reliance on numerical models increases, establishing robustness will become as important as demonstrating accuracy.

17 WIND ENERGY↗

A General Interface Method for Aeroelastic Analysis of Aircraft

The aeroelastic analysis of an aircraft requires an accurate and efficient procedure to couple aerodynamics and structures. The procedure needs an interface method to bridge the gap between the aerodynamic and structural models in order to transform loads and displacements. Such an interface method is described in this report. This interface method transforms loads computed by any aerodynamic code to a structural finite element (FE) model and converts the displacements from the FE model to the aerodynamic model. The approach is based on FE technology in which virtual work is employed to transform the aerodynamic pressures into FE nodal forces. The displacements at the FE nodes are then converted back to aerodynamic grid points on the aircraft surface through the reciprocal theorem in structural engineering. The method allows both high and crude fidelities of both models and does not require an intermediate modeling. In addition, the method performs the conversion of loads and displacements directly between individual aerodynamic grid point and its corresponding structural finite element and, hence, is very efficient for large aircraft models. This report also describes the application of this aero-structure interface method to a simple wing and an MD-90 wing. The results show that the aeroelastic effect is very important. For the simple wing, both linear and nonlinear approaches are used. In the linear approach, the deformation of the structural model is considered small, and the loads from the deformed aerodynamic model are applied to the original geometry of the structure. In the nonlinear approach, the geometry of the structure and its stiffness matrix are updated in every iteration and the increments of loads from the previous iteration are applied to the new structural geometry in order to compute the displacement increments. Additional studies to apply the aero-structure interaction procedure to more complicated geometry will be conducted in the second phase of the present contract.

Tzong, T.↗

Effects of Structural Flexibility on Aircraft-Engine Mounts

Analysis extends technique for design of widely used type of vibration-isolating mounts for aircraft engines, in which rubber mounting pads located in plane behind center of gravity of enginepropeller combination. New analysis treats problem in statics. Results of simple approach useful in providing equations for design of vibrationisolating mounts. Equations applicable in usual situation in which engine-mount structure itself relatively light and placed between large mass of engine and other heavy components of airplane.

Phillips, W. H.↗

Aeropropulsion structures

The structural engineer is faced with unique problems when dealing with aeropropulsion systems. He is faced with extremes in operating temperatures, rotational effects, and behaviors of advanced material systems which combine into complexities that require advances in many scientific disciplines involved in structural analysis and design procedures. This presentation provides an overview of the complexities of aeropropulsion structures and the theoretical, computational, and experimental research conducted to achieve the needed advances.

Nichols, Lester D.↗

System requirements specification for SMART structures mode

Specified here are the functional and informational requirements for software modules which address the geometric and data modeling needs of the aerospace structural engineer. The modules are to be included as part of the Solid Modeling Aerospace Research Tool (SMART) package developed for the Vehicle Analysis Branch (VAB) at the NASA Langley Research Center (LaRC). The purpose is to precisely state what the SMART Structures modules will do, without consideration of how it will be done. Each requirement is numbered for reference in development and testing.

Source record↗

Improving stability and strength characteristics of framed structures with nonlinear behavior

In this paper an optimal design procedure is introduced to improve the overall performance of nonlinear framed structures. The design methodology presented here is a multiple-objective optimization procedure whose objective functions involve the buckling eigenvalues and eigenvectors of the structure. A constant volume with bounds on the design variables is used in conjunction with an optimality criterion approach. The method provides a general tool for solving complex design problems and generally leads to structures with better limit strength and stability. Many algorithms have been developed to improve the limit strength of structures. In most applications geometrically linear analysis is employed with the consequence that overall strength of the design is overestimated. Directly optimizing the limit load of the structure would require a full nonlinear analysis at each iteration which would be prohibitively expensive. The objective of this paper is to develop an algorithm that can improve the limit-load of geometrically nonlinear framed structures while avoiding the nonlinear analysis. One of the novelties of the new design methodology is its ability to efficiently model and design structures under multiple loading conditions. These loading conditions can be different factored loads or any kind of loads that can be applied to the structure simultaneously or independently. Attention is focused on optimal design of space framed structures. Three-dimensional design problems are more complicated to carry out, but they yield insight into real behavior of the structure and can help avoiding some of the problems that might appear in planar design procedure such as the need for out-of-plane buckling constraint. Although researchers in the field of structural engineering generally agree that optimum design of three-dimension building frames especially in the seismic regions would be beneficial, methods have been slow to emerge. Most of the research in this area has dealt with the optimization of truss and plane frame structures.

Pezeshk, Shahram↗

Structural Health Monitoring of Composite Wound Pressure Vessels

The increasing use of advanced composite materials in the wide range of applications including Space Structures is a great impetus to the development of smart materials. Incorporating these FBG sensors for monitoring the integrity of structures during their life cycle will provide valuable information about viability of the usage of such material. The use of these sensors by surface bonding or embedding in this composite will measure internal strain and temperature, and hence the integrity of the assembled engineering structures. This paper focuses on such a structure, called a composite wound pressure vessel. This vessel was fabricated from the composite material: TRH50 (a Mitsubishi carbon fiber with a 710-ksi tensile strength and a 37 Msi modulus) impregnated with an epoxy resin from NEWPORT composites (WDE-3D-1). This epoxy resin in water dispersed system without any solvents and it cures in the 240-310 degrees F range. This is a toughened resin system specifically designed for pressure applications. These materials are a natural fit for fiber sensors since the polyimide outer buffer coating of fiber can be integrated into the polymer matrix of the composite material with negligible residual stress. The tank was wound with two helical patterns and 4 hoop wraps. The order of winding is: two hoops, two helical and two hoops. The wall thickness of the composite should be about 80 mil or less. The tank should burst near 3,000 psi or less. We can measure the actual wall thickness by ultrasonic or we can burst the tank and measure the pieces. Figure 1 shows a cylinder fabricated out of carbon-epoxy composite material. The strain in different directions is measured with a surface bonded fiber Bragg gratings and with embedded fiber Bragg gratings as the cylinder is pressurized to burst pressures. Figure 2 shows the strain as a function of pressure of carbon-epoxy cylinder as it is pressurized with water. Strain is measured in different directions by multiple gratings oriented in both axial and hoops directions.

Joseph Grant↗