Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface elasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

The longitudinal stability of elastic swept wings at supersonic speed

The longitudinal stability characteristics of elastic swept wings of high aspect ratio experiencing bending and torsional deformations are calculated for supersonic speed by the application of linearized lifting-surface theory. A parabolic wing deflection curve is assumed and the analysis is simplified by a number of structural approximations. The method is thereby limited in application to wings of high aspect ratio for which the root effects are small. Expressions for the lift, pitching-moment, and span load distribution characteristics are derived in terms of the elastic properties of the wing; namely, the design stress, the modulus of elasticity, the shearing modulus, and the maximum design load factor. The analysis applies to wings with leading edges swept behind the Mach lines. In all cases, however, the trailing edge is sonic or supersonic. Application of the method of analysis to wings with leading edges swept ahead of the Mach lines is discussed.

Frick, C W↗
NASA NTRS1974

Improving impact resistance of ceramic materials by energy absorbing surface layers

Energy absorbing surface layers were used to improve the impact resistance of silicon nitride and silicon carbide ceramics. Low elastic modulus materials were used. In some cases, the low elastic modulus was achieved using materials that form localized microcracks as a result of thermal expansion anisotropy, thermal expansion differences between phases, or phase transformations. In other cases, semi-vitreous or vitreous materials were used. Substantial improvements in impact resistance were observed at room and elevated temperatures.

Kirchner, H. P.↗
NASA NTRS1979

Analytical and scale model research aimed at improved hangglider design

Research consisted of a theoretical analysis which attempts to predict aerodynamic characteristics using lifting surface theory and finite-element structural analysis as well as an experimental investigation using 1/5 scale elastically similar models in the NASA Ames 2m x 3m (7' x 10') wind tunnel. Experimental data were compared with theoretical results in the development of a computer program which may be used in the design and evaluation of ultralight gliders.

Kroo, I.↗
NASA NTRS1982

Ultrasonic input-output for transmitting and receiving longitudinal transducers coupled to same face of isotropic elastic plate

The quantitative understanding of ultrasonic nondestructive evaluation parameters such as the stress wave factor were studied. Ultrasonic input/output characteristics for an isotropic elastic plate with transmitting and receiving longitudinal transducers coupled to the same face were analyzed. The asymptotic normal stress is calculated for an isotropic elastic half space subjected to a uniform harmonic normal stress applied to a circular region at the surface. The radiated stress waves are traced within the plate by considering wave reflections at the top and bottom faces. The output voltage amplitude of the receiving transducer is estimated by considering only longitudinal waves. Agreement is found between the output voltage wave packet amplitudes and times of arrival due to multiple reflections of the longitudinal waves.

Williams, J. H., Jr.↗
NASA NTRS1981

A diurnal resonance in the ocean tide and in the earth's load response due to the resonant free 'core nutation'

The effects of the oceans, which are subject to a resonance due to a free rotational eigenmode of an elliptical, rotating earth with a fluid outer core having an eigenfrequency of (1 + 1/460) cycle/day, on the body tide and nutational response of the earth to the diurnal luni-tidal force are computed. The response of an elastic, rotating, elliptical, oceanless earth with a fluid outer core to a given load distribution on its surface is first considered, and the tidal sea level height for equilibrium and nonequilibrium oceans is examined. Computations of the effects of equilibrium and nonequilibrium oceans on the nutational and deformational responses of the earth are then presented which show small but significant perturbations to the retrograde 18.6-year and prograde six-month nutations, and more important effects on the earth body tide, which is also resonant at the free core notation eigenfrequency.

Wahr, J. M.↗
NASA NTRS1990

Heterogeneities in the thickness of the elastic lithosphere of Mars - Constraints on heat flow and internal dynamics

Estimates of the effective thickness of the Martian elastic lithosphere are reviewed, and these thickness values are converted to estimates of lithospheric thermal gradients and surface heat flow by means of temperature-dependent strength envelopes. The results of estimates of thermal gradients for various locations, together with the information on the geological epochs appropriate to each estimate of thermal gradient, were related to the global heat flux, the interior thermal evolution, the Martial lithospheric reheating mechanisms, and the evolution of major volcanic provinces on Mars.

Solomon, Sean C.↗
NASA NTRS2006

Multifunctional Characteristics of Carbon Nanotube (CNT) Yarn Composites

By forming composite structures with Carbon Nanotube (CNT) yarns we achieve materials capable of measuring strain and composite structures with increased mechanical strength. The CNT yarns used are of the 2-ply and 4-ply variety with the yarns having diameters of about 15-30 micrometers. The strain sensing characteristics of the yarns are investigated on test beams with the yarns arranged in a bridge configuration. Additionally, the strain sensing properties are also investigated on yarns embedded on the surface of a flexible membrane. Initial mechanical strength tests also show an increase in the modulus of elasticity of the composite materials while incurring a weight penalty of less than one-percent. Also presented are initial temperature characterizations of the yarns.

Hernandez, Corey D.↗
NASA NTRS1993

Possible flexural signatures around Olympus and Ascraeus Montes, Mars

The effective elastic thickness (h) of the lithosphere provides a measure of the thermal and mechanical state of a planet's shallow interior. An estimate of h in the vicinity of a feature that constitutes a load on a planetary surface can be determined from the flexural response of the lithosphere to the load. This approach has been applied to Mars by calculating radial stresses associated with lithospheric flexure associated with surface loads, and comparing the results to the positions of circumferential graben surrounding the major Martian shield volcanoes and mascon basins. However, many prominent surface loads on Mars, most notably the Olympus Mons volcano, do not exhibit flexural graben. In these instances application of the above method can provide only a lower limit of effective elastic thickness. An alternative method of determining h is to calculate the vertical displacements associated with the flexural loading and to compare the amplitude and shape of the flexural profile to observed topography. This method has not been applied to flexural problems on Mars because of the poor resolution of Martian topographic data. However, previous analyses have shown that the lithosphere around major volcanic shields should exhibit vertical deflections of order 1 km over horizontal baselines of order 100 km. We were thus motivated to search for the presence of flexural troughs in the existing Mars topography data.

Zuber, M. T.↗
NASA NTRS1984

The role of material properties in adhesion

When two solid surfaces are brought into contact strong adhesive bond forces can develop between the materials. The magnitude of the forces will depend upon the state of the surfaces, cleanliness and the fundamental properties of the two solids, both surface and bulk. Adhesion between solids is addressed from a theoretical consideration of the electronic nature of the surfaces and experimentally relating bond forces to the nature of the interface resulting from solid state contact. Surface properties correlated with adhesion include, atomic or molecular orientation, reconstruction and segregation as well as the chemistry of the surface specie. Where dissimilar solids are in contact the contribution of each is considered as is the role of their interactive chemistry on bond strength. Bulk properties examined include elastic and plastic behavior in the surficial regions, cohesive binding energies, crystal structure, crystallographic orientation and state. Materials examined with respect to interfacial adhesive interactions include metals, alloys, ceramics, polymers and diamond. They are reviewed both in single and polycrystalline form. The surfaces of the contacting solids are studied both in the atomic or molecularly clean state and in the presence of selected surface contaminants.

Buckley, D. H.↗
NASA NTRS2003

Elastic-Plastic Thermal Stress Analysis of a High-Pressure Cryogenic Storage Tank

The thermal stresses on a cryogenic storage tank contribute strongly to the state of stress of the tank material and its ability to withstand operational stresses. These thermal stresses also affect the growth of any surface damage that might occur in the tank walls. These stresses are particularly of concern during the initial cooldown period for a new tank placed into service, and during any subsequent thermal cycles. A previous preliminary elastic analysis showed that the thermal stress on the inner wall would reach approximately 1,000MPa (145,000 psi). This stress far exceeds the ASTM specified room temperature values for both yield (170MPa) and ultimate (485 MPa) strength for 304L stainless steel. The present analysis determines the thermal stresses using an elastic-plastic model. The commercial software application ANSYS was used to determine the transient spatial temperature profile and the associated spatial thermal stress profiles in a segment of a thick-walled vessel during a typical cooldown process. A strictly elastic analysis using standard material properties for 304L stainless steel showed that the maximum thermal stress on the inner and outer walls was approximately 960 MPa (tensile) and - 270 MPa (compressive) respectively. These values occurred early in the cooldown process, but at different times, An elastic-plastic analysis showed significantly reducing stress, as expected due to the plastic deformation of the material. The maximum stress for the inner wall was approximately 225 MPa (tensile), while the maximum stress for the outer wall was approximately - 130 MPa (compressive).

Barker, J. Mark↗
NASA NTRS1974

Analysis of complex elastic structures by a Rayleigh-Ritz component modes method using Lagrange multipliers

The free vibrations of elastic structures of arbitrary complexity were analyzed in terms of their component modes. The method was based upon the use of the normal unconstrained modes of the components in a Rayleigh-Ritz analysis. The continuity conditions were enforced by means of Lagrange Multipliers. Examples of the structures considered are: (1) beams with nonuniform properties; (2) airplane structures with high or low aspect ratio lifting surface components; (3) the oblique wing airplane; and (4) plate structures. The method was also applied to the analysis of modal damping of linear elastic structures. Convergence of the method versus the number of modes per component and/or the number of components is discussed and compared to more conventional approaches, ad-hoc methods, and experimental results.

Klein, L. R.↗
NASA NTRS1981

Application of the line-spring model to a cylindrical shell containing a circumferential or axial part-through crack

An approximate solution was obtained for a cylindrical shell containing a part-through surface crack. It was assumed that the shell contains a circumferential or axial semi-elliptic internal or external surface crack and was subjected to a uniform membrane loading or a uniform bending moment away from the crack region. A Reissner type theory was used to account for the effects of the transverse shear deformations. The stress intensity factor at the deepest penetration point of the crack was tabulated for bending and membrane loading by varying three dimensionless length parameters of the problem formed from the shell radius, the shell thickness, the crack length, and the crack depth. The upper bounds of the stress intensity factors are provided by the results of the elasticity solution obtained from the axisymmetric crack problem for the circumferential crack, and that found from the plane strain problem for a circular ring having a radial crack for the axial crack. The line-spring model gives the expected results in comparison with the elasticity solutions. Results also compare well with the existing finite element solution of the pressurized cylinder containing an internal semi-elliptic surface crack.

Delale, F.↗
NASA NTRS1972

Propagation of the transverse normal stress in a thick plate due to distributed lateral impulsive loadings

A theoretical study of the elastic stresses produced in an infinite plate when struck by a high-speed object is presented. The solution is obtained by means of linear elasticity. Laplace transformation techniques are employed to solve the axisymmetric problem. The plate is loaded normal to its surface with a uniform load over a circular area. The normal stress at the wave front of the unreflected dilatation wave along the axis and its variation with the radius of loading are determined. Various facets of the problem are discussed.

Oline, L. W.↗
NASA NTRS1974

A finite element analysis of fatigue crack closure

Experiments have shown that fatigue cracks close at positive loads during constant-amplitude load cycling. The crack-closure phenomenon is caused by residual plastic deformations remaining in the wake of an advancing crack tip. The present paper is concerned with the application of a two-dimensional, nonlinear, finite-element analysis for predicting crack-closure and crack-opening stresses during cyclic loading. A two-dimensional finite-element computer program, which accounts for both elastic-plastic material behavior and changing boundary conditions associated with crack extension and intermittent contact of the crack surfaces under cyclic loading, has been developed. An efficient technique to account for changing boundary conditions was also incorporated into the nonlinear analysis program. This program was subsequently used to study crack extension and crack closure under constant-amplitude and two-level block loading. The calculated crack-closure and crack-opening stresses were qualitatively consistent with experimental observations.

Newman, J. C., Jr.↗
NASA NTRS1976

A finite-element analysis of fatigue crack closure

The paper is concerned with the application of a two-dimensional, nonlinear, finite-element analysis using an incremental theory of plasticity to predict crack-closure and crack-opening stresses during the crack-growth process under cyclic loading. A two-dimensional finite-element computer program is developed, which accounts for both elastic-plastic material behavior and changing boundary conditions associated with crack extension and intermittent contact of the crack surfaces under cyclic loading. An efficient technique to account for changing boundary conditions under cyclic loading is also incorporated into the nonlinear analysis program. This program is used to study crack extension and crack closure behavior in a center-cracked panel under constant-amplitude and two-level block loading. The calculated crack-opening stresses are found to be quantitatively consistent with experimental measurements.

Newman, J. C., Jr.↗
NASA NTRS1976

Random vibration of compliant wall

The paper is concerned with the realistic case of two-dimensional random motion of a membrane with bending stiffness supported on a viscoelastic spring substrate and on an elastic base plate under both subsonic and supersonic boundary layer turbulence. The cross-power spectral density of surface displacements is solved in terms of design variables of the compliant wall - such as the dimensions and material properties of the membrane (Mylar), substrate (PVC foam), and panel (aluminum) - so that a sensitivity analysis can be made to examine the influence of each design variable on the surface response statistics. Three numerical examples typical of compliant wall design are worked out and their response statistics in relation to wave drag and roughness drag are assessed. The results can serve as a guideline for experimental investigation of the drag reduction concept through the use of a compliant wall.

Yang, J.-N.↗
NASA NTRS1981

Effects of geometric variables on rub characteristics of Ti-6Al-4V

Experiments simulating rub interactions between Ti-6Al-4V blade tips and various seal materials were conducted. The number of blade tips and the blade tip geometry were varied to determine their effects on rub forces and on wear phenomena. Contact was found to be quite unsteady for all blade tip geometries except for those incorporating deliberately rounded blade tips. The unsteady contact was characterized by long periods of rubbing contact and increasing blade tip that terminated in sudden rapid metal removal, sometimes accompanied by tearing and disruption of porous seal material under the rub surface. A model describing the blade tip loading is proposed and is based on the propagation of an elastic stress wave through the seal material as the seal material is dynamically compressed by the blade tip leading edge.

Bill, R. C.↗