Search NASA⌕ Search

SEARCH · Search NASA

Results for “Survival Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Simple analyses of paths through windshears and downdrafts

Quasi-steady analysis and energy-state approximation are employed to study flight paths through windshears and downdrafts. Takeoff flight is mainly considerd while landing flight is briefly discussed. The relation between angle of attack and airspeed is found to be almost independent of horizontal wind and slightly dependent on vertical wind. In slowly-varying windshears and/or downdrafts, quasi-steady flight can be achieved by flying an aircraft at a lower than nominal climb rate; this will avoid stall. In severe windshears and/or downdrafts, energy-state approximation indicates that descending paths save more energy and provide higher survival capability.

Zhao, Yiyuan↗
NASA NTRS2004

High Temperature Propulsion System Structural Seals for Future Space Launch Vehicles

Durable, flexible sliding seals are required in advanced hypersonic engines to seal the perimeters of movable engine ramps for efficient, safe operation in high heat flux environments at temperatures of 2000 to 2500 F. Current seal designs do not meet the demanding requirements for future engines, so NASA s Glenn Research Center is developing advanced seals and preloading devices to overcome these shortfalls. An advanced ceramic wafer seal design and two types of seal preloading devices were evaluated in a series of compression, scrub, and flow tests. Silicon nitride wafer seals survived 2000 in. 1000 cycles) of scrubbing at 1600 F against an Inconel 625 rub surface with no chips or signs of damage. Flow rates measured for the wafers before and after scrubbing were almost identical and were up to 32 times lower than those recorded for the best braided rope seal flow blockers. Canted coil springs and silicon nitride compression springs showed promise conceptually as potential seal preloading devices to help maintain seal resiliency. A finite element model of the canted coil spring revealed that it should be possible to produce a spring out of high temperature materials for applications at 2000+ F.

Dunlap, Patrick H., Jr.↗
NASA NTRS2003

High Temperature Propulsion System Structural Seals for Future Space Launch Vehicles

Durable, flexible sliding seals are required in advanced hypersonic engines to seal the perimeters of movable engine ramps for efficient, safe operation in high heat flux environments at temperatures of 2000 to 2500 F. Current seal designs do not meet the demanding requirements for future engines, so NASA's Glenn Research Center is developing advanced seals and preloading devices to overcome these shortfalls. An advanced ceramic wafer seal design and two types of seal preloading devices were evaluated in a series of compression, scrub, and flow tests. Silicon nitride wafer seals survived 2000 in. (1000 cycles) of scrubbing at room temperature against an Inconel 625 rub surface with no chips or signs of damage. Flow rates measured for the wafers before and after scrubbing were almost identical and were much lower than those recorded for the best braided rope seal flow blockers. Canted coil springs and silicon nitride compression springs showed promise conceptually as potential seal preloading devices to help maintain seal resiliency. A finite element model of the canted coil spring revealed that it should be possible to produce a spring out of high temperature materials for applications at 2000+ F.

Dunlap, Patrick H., Jr.↗
NASA NTRS2004

Further Investigations of Hypersonic Engine Seals

Durable, flexible sliding seals are required in advanced hypersonic engines to seal the perimeters of movable engine ramps for efficient, safe operation in high heat flux environments at temperatures of 2000 to 2500 F. Current seal designs do not meet the demanding requirements for future engines, so NASA's Glenn Research Center is developing advanced seals and preloading devices to overcome these shortfalls. An advanced ceramic wafer seal design and two silicon nitride compression spring designs were evaluated in a series of compression, scrub, and flow tests. Silicon nitride wafer seals survived 2000 in. (50.8 m) of scrubbing at 2000 F against a silicon carbide rub surface with no chips or signs of damage. Flow rates measured for the wafers before and after scrubbing were almost identical and were up to 32 times lower than those recorded for the best braided rope seal flow blockers. Silicon nitride compression springs showed promise conceptually as potential seal preload devices to help maintain seal resiliency.

Dunlap, Patrick H., Jr.↗
NASA NTRS1999

Critical target and dose and dose-rate responses for the induction of chromosomal instability by ionizing radiation

To investigate the critical target, dose response and dose-rate response for the induction of chromosomal instability by ionizing radiation, bromodeoxyuridine (BrdU)-substituted and unsubstituted GM10115 cells were exposed to a range of doses (0.1-10 Gy) and different dose rates (0.092-17.45 Gy min(-1)). The status of chromosomal stability was determined by fluorescence in situ hybridization approximately 20 generations after irradiation in clonal populations derived from single progenitor cells surviving acute exposure. Overall, nearly 700 individual clones representing over 140,000 metaphases were analyzed. In cells unsubstituted with BrdU, a dose response was found, where the probability of observing delayed chromosomal instability in any given clone was 3% per gray of X rays. For cells substituted with 25-66% BrdU, however, a dose response was observed only at low doses (<1.0 Gy); at higher doses (>1.0 Gy), the incidence of chromosomal instability leveled off. There was an increase in the frequency and complexity of chromosomal instability per unit dose compared to cells unsubstituted with BrdU. The frequency of chromosomal instability appeared to saturate around approximately 30%, an effect which occurred at much lower doses in the presence of BrdU. Changing the gamma-ray dose rate by a factor of 190 (0.092 to 17.45 Gy min(-1)) produced no significant differences in the frequency of chromosomal instability. The enhancement of chromosomal instability promoted by the presence of the BrdU argues that DNA comprises at least one of the critical targets important for the induction of this end point of genomic instability.

NASA Discipline Radiation Health↗
NASA NTRS1993

Application of a hybrid digital-optical cross-correlator as a semi-autonomous vision system

We describe a complex optical system consisting of a 4f optical correlator with programmable filters under control of a digital on-board computer that operates at video rates for filter generation, storage, and management. It gives intelligent vision to a semi-autonomous vehicle, with ability to recognize immediate danger to its survival in the near term and ability to pursue navigational goals on the basis of tracking the previously identified features.

Scholl, Marija S.↗
NASA NTRS2001

Further Investigations of Control Surface Seals for the X-38 Re-Entry Vehicle

NASA is currently developing the X-38 vehicle that will be used to demonstrate the technologies required for a potential crew return vehicle (CRV) for the International Space Station. This vehicle would serve both as an ambulance for medical emergencies and as an evacuation vehicle for the Space Station. Control surfaces on the X-38 (body flaps and rudder/fin assemblies) require high temperature seals to limit hot gas ingestion and transfer of heat to underlying low-temperature structures to prevent over-temperature of these structures and possible loss of the vehicle. NASAs Johnson Space Center (JSC) and Glenn Research Center (GRC) are working together to develop and evaluate seals for these control surfaces. This paper presents results for compression. flow, scrub, and arc jet tests conducted on the baseline X-38 rudder/fin seal design. Room temperature seal compression tests were performed at low compression levels to determine load versus linear compression, preload. contact area, stiffness. and resiliency characteristics under low load conditions. For all compression levels that were tested, unit loads and contact pressures for the seals were below the 5 lb/in. and 10 psi limits required to limit the loads on the adjoining Shuttle thermal tiles that the seals will contact. Flow rates through an unloaded (i.e. 0% compression) double arrangement were twice those of a double seal compressed to the 20% design compression level. The seals survived an ambient temperature 1000 cycle scrub test over relatively rough Shuttle tile surfaces. The seals were able to disengage and re-engage the edges of the rub surface tiles while being scrubbed over them. Arc jet tests were performed to experimentally determine anticipated seal temperatures for representative flow boundary conditions (pressures and temperatures) under simulated vehicle re-entry conditions. Installation of a single seat in the gap of the test fixture caused a large temperature drop (1710 F) across the seal location as compared to an open gap condition (140 F) confirming the need for seals in the rudder/fin gap location. The seal acted as an effective thermal barrier limiting heat convection through the seal gap and minimizing temperature increases downstream of the seal during maximum heating conditions.

Dunlap, Patrick H., Jr.↗
NASA NTRS2000

Erosion Coatings for High-Temperature Polymer Composites: A Collaborative Project With Allison Advanced Development Company

The advantages of replacing metals in aircraft turbine engines with high-temperature polymer matrix composites (PMC's) include weight savings accompanied by strength improvements, reduced part count, and lower manufacturing costs. Successfully integrating high-temperature PMC's into turbine engines requires several long-term characteristics. Resistance to surface erosion is one rarely reported property of PMC's in engine applications because PMC's are generally softer than metals and their erosion resistance suffers. Airflow rates in stationary turbine engine components typically exceed 2.3 kg/sec at elevated temperatures and pressures. In engine applications, as shown in the following photos, the survivability of PMC components is clearly a concern, especially when engine and component life-cycle requirements become longer. Although very few publications regarding the performance of erosion coatings on PMC's are available particularly in high-temperature applications the use of erosion-resistant coatings to significantly reduce wear on metallic substrates is well documented. In this study initiated by the NASA Glenn Research Center at Lewis Field, a low-cost (less than $140/kg) graphite-fiber-reinforced T650 35/PMR 15 sheet-molding compound was investigated with various coatings. This sheet-molding compound has been compression molded into many structurally complicated components, such as shrouds for gas turbine inlet housings and gearboxes. Erosion coatings developed for PMC s in this study consisted of a two-layered system: a bondcoat sprayed onto a cleaned PMC surface, followed by an erosion-resistant, hard topcoat sprayed onto the bondcoat as shown in following photomicrograph. Six erosion coating systems were evaluated for their ability to withstand harsh thermal cycles, erosion resistance (ASTM G76 83 "Standard Practice for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets") using Al2O3, and adhesion to the graphite fiber polyimide composite (ASTM D 4541 95 "Pull Off Strength of Coatings"). Glenn and Allison Advanced Development Company collaborated to optimize erosion coatings for gas turbine fan and compressor applications. All the coating systems survived aggressive thermal cycling without spalling. During erosion tests (see the final photo), the most promising coating systems tested had Cr3C2-NiCr and WC-Co as the hard topcoats. In all cases, these coating systems performed significantly better than that with a TiN hard topcoat. When material depth (thickness) loss is considered, the Cr3C2-NiCr and WC-Co coating systems provided, on average, an erosion resistance 8.5 times greater than that for the uncoated PMR 15/T650 35 composite. Similarly, Cr3C2-NiCr and WC-Co coating systems adhered to the PMC substrate during tensile tests significantly better than systems containing a TiN topcoat. Differences in topcoats of Cr3C2-NiCr and WC-Co were determined by considering issues such as cost and environmental impact. The preferred erosion-resistant coating system for PMR 15/T650 35 has WC-Co as the hard topcoat. This system provides the following benefits in comparison to the coating system with Cr3C2-NiCr topcoat: lower powder material cost (15 to 20 percent), environmentally friendly materials (Cr3C2-NiCr is hazardous), and higher deposition yield (10 to 15 percent), which results in less waste.

Sutter, James K.↗
NASA NTRS2017

Stratosphere Conditions Inactivate Bacterial Endospores from a Mars Spacecraft Assembly Facility

Every spacecraft sent to Mars is allowed to land viable microbial bioburden, including hardy endospore-forming bacteria resistant to environmental extremes. Earth's stratosphere is severely cold, dry, irradiated, and oligotrophic; it can be used as a stand-in location for predicting how stowaway microbes might respond to the Martian surface. We launched E-MIST, a high-altitude NASA balloon payload on 10 October 2015 carrying known quantities of viable Bacillus pumilus SAFR-032 (4.07?×?10(7) spores per sample), a radiation-tolerant strain collected from a spacecraft assembly facility. The payload spent 8?h at ~31?km above sea level, exposing bacterial spores to the stratosphere. We found that within 120 and 240?min, spore viability was significantly reduced by 2 and 4 orders of magnitude, respectively. By 480?min, <0.001% of spores carried to the stratosphere remained viable. Our balloon flight results predict that most terrestrial bacteria would be inactivated within the first sol on Mars if contaminated spacecraft surfaces receive direct sunlight. Unfortunately, an instrument malfunction prevented the acquisition of UV light measurements during our balloon mission. To make up for the absence of radiometer data, we calculated a stratosphere UV model and conducted ground tests with a 271.1?nm UVC light source (0.5 W/m(2)), observing a similarly rapid inactivation rate when using a lower number of contaminants (640 spores per sample). The starting concentration of spores and microconfiguration on hardware surfaces appeared to influence survivability outcomes in both experiments. With the relatively few spores that survived the stratosphere, we performed a resequencing analysis and identified three single nucleotide polymorphisms compared to unexposed controls. It is therefore plausible that bacteria enduring radiation-rich environments (e.g., Earth's upper atmosphere, interplanetary space, or the surface of Mars) may be pushed in evolutionarily consequential directions.

Planetary protection↗
NASA NTRS1991

The relative importance of prebiotic synthesis on the Earth and input from comets and meteorites

The prebiotic synthesis of hydrogen cyanide and formaldehyde was studied by the action of electric discharges on various model primitive atmospheres containing CH4, CO, and CO2. Photochemical production rates would also have been important and were calculated for HCN and H2CO. A reasonable rate of synthesis of amino acids from these sources is about 10 n moles/(sq cm yr) or 0.10 moles/sq cm in 10(exp 7) yrs. This would give a concentration of 3 x 10(exp -4) M in an ocean of the present size (300 liters/sq cm). The amino acids cannot accumulate over a longer period because the entire ocean passes through the 350 C submarine vents in 10(exp 7) yrs, which decomposes all the organic compounds. A number of workers have calculated the influx of comets and meteorites on the primitive earth, both as a destructive process for organic compounds and for any life that was present, as well as a source of organic compounds. Some of the amino acids from the meteorite proposed to have hit the earth 65 x 10(exp 6) yrs ago were detected at the Cretaceous/Tertiary boundary sediments. The problem with proposing a large scale input of organic compounds from meteorites and comets is that they must survive passage through the atmosphere and impact. There are some processes that would allow survival such as showers of centimeter to meter sized meteorites and various aerodynamic braking processes for larger objects. Even if a significant amount of the organic material survived impact, the destructive processes in the hydrothermal vents would remove these compounds on the average in 10(exp 7) yrs or less. If it is assumed that the input rate was sufficient to overcome these destructive processes, then too much carbon and water, especially from comets, would have been added to the surface of the earth. It was concluded that while some organic material was added to the earth from comets and meteorites, the amount available from these sources at a given time was only a few percent of that from earth based syntheses.

Miller, S. L.↗
DOE OSTI2022

Complex decay dynamics of HIV virions, intact and defective proviruses, and 2LTR circles following initiation of antiretroviral therapy

In persons living with HIV-1 (PLWH) who start antiretroviral therapy (ART), plasma virus decays in a biphasic fashion to below the detection limit. The first phase reflects the short half-life (<1 d) of cells that produce most of the plasma virus. The second phase represents the slower turnover (t 1/2 = 14 d) of another infected cell population, whose identity is unclear. Using the intact proviral DNA assay (IPDA) to distinguish intact and defective proviruses, we analyzed viral decay in 17 PLWH initiating ART. Circulating CD4 + T cells with intact proviruses include few of the rapidly decaying first-phase cells. Instead, this population initially decays more slowly (t 1/2 = 12.9 d) in a process that largely represents death or exit from the circulation rather than transition to latency. This more protracted decay potentially allows for immune selection. After ~3 mo, the decay slope changes, and CD4 + T cells with intact proviruses decay with a half-life of 19 mo, which is still shorter than that of the latently infected cells that persist on long-term ART. Two-long-terminal repeat (2LTR) circles decay with fast and slow phases paralleling intact proviruses, a finding that precludes their use as a simple marker of ongoing viral replication. Proviruses with defects at the 5' or 3' end of the genome show equivalent monophasic decay at rates that vary among individuals. Understanding these complex early decay processes is important for correct use of reservoir assays and may provide insights into properties of surviving cells that can constitute the stable latent reservoir.

2LTR circles↗
NASA NTRS1994

Estimates of cellular mutagenesis from cosmic rays

A parametric track structure model is used to estimate the cross section as a function of particle velocity and charge for mutations at the hypoxanthine guanine phosphoribosyl transferase (HGPRT) locus in human fibroblast cell cultures. Experiments that report the fraction of mutations per surviving cell for human lung and skin fibroblast cells indicate small differences in the mutation cross section for these two cell lines when differences in inactivation rates between these cell lines are considered. Using models of cosmic ray transport, the mutation rate at the HGPRT locus is estimated for cell cultures in space flight and rates of about 2 to 10 x 10(exp -6) per year are found for typical spacecraft shielding. A discussion of how model assumptions may alter the predictions is also presented.

Cucinotta, Francis A.↗
NASA NTRS1999

The Role of Boundary Layer Aerosol in the Vertical Development of Precipitation and Electrification: Another Look at the Contrast Between Lightning over Land and Over Ocean

Comparisons are made between the cloud condensation nuclei (CCN) concentration in the boundary layer and radar/electrical observations of the vertical development of precipitation and lightning in both the 'break period' and 'monsoon' regimes in tropical Brazil. The initial radar echoes and the maximum flash rates are found to be higher when the CCN concentration is higher, characteristic of the 'break period' conditions. One possible explanation for both observations is the survival of cloud droplets against coalescence and their attainment of the mixed phase region aloft.

Williams, E.↗
NASA NTRS2002

Comparative Fatigue Lives of Rubber and PVC Wiper Cylindrical Coatings

Three coating materials for rotating cylindrical-coated wiping rollers were fatigue tested in 2 Intaglio printing presses. The coatings were a hard, cross-linked, plasticized PVC thermoset (P-series); a plasticized PVC (A-series); and a hard, nitryl rubber (R-series). Both 2- and 3-parameter Weibull analyses as well as a cost-benefit analysis were performed. The mean value of life for the R-series coating is 24 and 9 times longer than the P- and A-series coatings, respectively. Both the cost and replacement rate for the R-series coating was significantly less than those for the P- and A-series coatings. At a very high probability of survival the R-series coating is approximately 2 and 6 times the lives of the P- and A-series, respectively, before the first failure occurs. Where all coatings are run to failure, using the mean (life) time between removal (MTBR) for each coating to calculate the number of replacements and costs provides qualitatively similar results to those using a Weibull analysis.

Vlcek, Brian L.↗
DOE OSTI2019

Endovascular Extra-Anatomic Femoro-Popliteal Bypass for Limb Salvage in Chronic Critical Limb Ischemia

Purpose: To report the initial clinical experience with fully endovascular extra-anatomic femoro-popliteal bypass (FPB) for limb salvage in patients with critical limb ischemia (CLI) and no traditional endovascular or surgical revascularization options. Methods: Between June 2013 and May 2018, endovascular procedure was proposed for limb salvage during multidisciplinary team meeting in fifteen hospitalized patients (median age 67 years; 73% men) with CLI and a high risk of major amputation. Primary outcome was amputation-free survival at 1 year. Secondary outcomes included mortality, cardiovascular (CV) events and major limb amputation at 1 year, primary/secondary bypass patency and wound healing at the last follow-up visit. Procedure-related complications (deaths, CV events, hemorrhages) were recorded through 30 days. Results: Technical procedure success rate was 100%. Major peri-procedural outcomes occurred in two patients (13%): One patient died secondary to cardiogenic shock; one patient suffered acute coronary syndrome associated with iliopsoas bleeding. No major amputation occurred through 30 days. Median follow-up period was 21.5 (18.25–45.5) months (last follow-up visits on April 2019). Amputation-free survival at 1-year and at the last follow-up visit was 80% and 53%, respectively. Cumulative mortality at 1-year and at the last follow-up visit was 13% and 33%, respectively. Primary and secondary bypass patency was 27% and 60%, respectively. Complete wound healing was achieved in 11 patients (73%). Conclusion: Endovascular extra-anatomic FPB represents an innovative approach for limb salvage in CLI with no traditional endovascular or surgical revascularization options. Our clinical experience highlights that this technique remains challenging because of frequent comorbidities and fragility of this patient population. Level of Evidence: Level 4, Case series.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2020

Measurement and Simulation of Vacancy Formation in 2-MeV Self-irradiated Pure Fe

Positron annihilation spectroscopy is a powerful tool to quantify the amount of vacancies and vacancy clusters in materials. The technique has been utilized to study the induced defects in materials after ion beam and neutron irradiations. Here we make the case for how the technique can and should be utilized to quantify the defects created by irradiation in situ during irradiation to foster a more thorough understanding of the surviving defects after initial collision cascades. This paper outlines a future experimental approach and its meaning for the nuclear materials community, being able to benchmark commonly used rate theory models of damage evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Post-Mastectomy Radiotherapy After Neoadjuvant Chemotherapy in Breast Cancer: A Pooled Retrospective Analysis of Three Prospective Randomized Trials

Background: The impact of locoregional radiotherapy (RT) after neoadjuvant chemotherapy (NACT) and mastectomy in breast cancer patients is currently unclear. Several publications have suggested that patients with a favorable response to NACT might not benefit from RT after mastectomy. Methods: A retrospective analysis of three prospective randomized NACT trials was performed. Information on the use of RT was available for 817 breast cancer patients with non-inflammatory breast cancer who underwent mastectomy after NACT within the GeparTrio, GeparQuattro, and GeparQuinto-trials. RT was administered to 676 of these patients (82.7%). Results: The 5-year cumulative incidence of locoregional recurrence (LRR) was 15.2% (95% confidence interval [CI] 9.0–22.8%) in patients treated without RT and 11.3% in patients treated with RT (95% CI 8.7–14.3%). In the multivariate analysis, RT was associated with a lower risk of LRR (hazard ratio 0.51, 95% CI 0.27–1.0; p = 0.05). This effect was shown especially in patients with cT3/4 tumors, as well as in patients who were cN+ before neoadjuvant therapy, including those who converted to ypN0 after neoadjuvant therapy. In the bivariate analysis, disease-free survival was significantly worse in patients who received RT, however this was not confirmed in the multivariate analysis. Conclusions: Our results suggest that RT reduces the LRR rates in breast cancer patients who receive a mastectomy after NACT without an improvement in DFS. Prospective randomized controlled trials such as the National Surgical Adjuvant Breast and Bowel Project B-51/RTOG 1304 trial will analyze whether RT has any benefit in patients who have a favorable response after NACT.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2025

Aggressively Dissipative Dark Dwarfs: The Effects of Atomic Dark Matter on the Inner Densities of Isolated Dwarf Galaxies

We present the first suite of cosmological hydrodynamical zoom-in simulations of isolated dwarf galaxies for a dark sector that consists of cold dark matter and a strongly dissipative subcomponent. The simulations are implemented in GIZMO and include standard baryons following the FIRE-2 galaxy formation physics model. The dissipative dark matter is modeled as atomic dark matter (aDM), which forms a dark hydrogen gas that cools in direct analogy to the Standard Model. Our suite includes seven different simulations of ∼10 10 M ⊙ systems that vary over the aDM microphysics and the dwarf’s evolutionary history. We identify a region of aDM parameter space where the cooling rate is aggressive and the resulting halo density profile is universal. In this regime, the aDM gas cools rapidly at high redshifts, and only a small fraction survives in the form of a central dark gas disk; the majority collapses centrally into collisionless dark “clumps,” which are clusters of subresolution dark compact objects. These dark clumps rapidly equilibrate in the inner galaxy, resulting in an approximately isothermal distribution that can be modeled with a simple fitting function. Even when only a small fraction (∼5%) of the total dark matter is strongly dissipative, the central densities of classical dwarf galaxies can be enhanced by over an order of magnitude, providing a sharp prediction for observations.

cold dark matter↗