Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEMPERATURE PROFILE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Heat Transfer in the Turbulent Incompressible Boundary Layer: Step Wall-Temperature Distribution - Part 2

Heat-transfer rates and temperature profiles for the turbulent incompressible flow of air over a flat plate with a stepwise temperature distribution (unheated starting length) were measured for a variety of step positions at Reynolds numbers up to 3.5 x 10(exp 6). Comparison of the data with existing heat-transfer analyses indicates that an improved analysis is needed. An integral analysis is made that agrees very well with the data and allows a simple correction for the unheated starting length. In addition, a differential analysis is made that allows prediction of the temperature profiles from the velocity profiles, and good agreement with experimental profiles is obtained.

Reynolds, W. C.↗

Temperature distribution in an aircraft tire at low ground speeds

An experimental study was conducted to define temperature profiles of 22 x 5.5, type 7, bias ply aircraft tires subjected to freely rolling, yawed rolling, and light braking conditions. Temperatures along the inner wall of freely rolling tires were greater than those near the outer surface. The effect of increasing tire deflection was to increase the temperature within the shoulder and sidewall areas of the tire carcass. The effect of cornering and braking was to increase the treat temperature. For taxi operations at fixed yaw angles, temperature profiles were not symmetric. Increasing the ground speed produced only moderate increases in tread temperature, whereas temperatures in the carcass shoulder and sidewall were essentially unaffected.

Mccarty, J. L.↗

Origins of the Solar Wind

This paper presented the differential emission measure analysis of SUMER observations of a coroner streamer. We found that: The coroner streamer is isothermal at all heights. This suggests that the loops comprising the streamer must have very flat temperature profiles. The coroner streamer is "overdense" relative to the predictions of hydrostatic equilibrium at most heights. At the lowest heights the streamer is actually "underdense". The SUMER temperature measurements are not consistent with those derived from simultaneous SXT observations. SXT indicates systematically higher temperatures as well as a strong temperature gradient. These SUMER measurements yield somewhat lower temperatures and no gradient in the temperature with height. Previous work has suggested that there may be a hot component to the streamer that is preferentially observed with SXT. Our analysis shows that high temperature emission lines would be observed with SUMER if this were true and thus discounts this possibility. We suggested that scattered light in SXT might produce spurious temperature measurements. The temperature and density structure of this coroner streamer are very similar to "TRACE" active region loops (flat temperature profiles, overdense relative to uniform heating, and relatively cool temperatures).

Warren, Harry↗

Analysis of the feasibility of an experiment to measure carbon monoxide in the atmosphere

The feasibility of measuring atmospheric carbon monoxide from a remote platform using the correlation interferometry technique was considered. It has been determined that CO data can be obtained with an accuracy of 10 percent using this technique on the first overtone band of CO at 2.3 mu. That band has been found to be much more suitable than the stronger fundamental band at 4.6 mu. Calculations for both wavelengths are presented which illustrate the effects of atmospheric temperature profiles, inversion layers, ground temperature and emissivity, CO profile, reflectivity, and atmospheric pressure. The applicable radiative transfer theory on which these calculations are based is described together with the principles of the technique.

Bortner, M. H.↗

Narrowband lidar technique for sodium temperature and Doppler wind observations of the upper atmosphere

A new two-frequency lidar for measuring mesospheric Na temperature profiles is described that uses a stabilized CW single-mode dye laser oscillator (rms frequency jitter less than 1 MHz) followed by a pulsed dye power amplifier (140 MHz FWHM linewidth) that is pumped by an injection-locked Nd:YAG laser. The laser oscillator is tuned to the two operating freqencies by observing the Doppler-free structure of the Na D2 fluorescence spectrum in a vapor cell. The lidar technique and initial observations of the temperature profile between 82 and 102 km at Ft. Collins, CO are described. Absolute temperature accuracies at the Na layer peak of better than + or - 3 K with a vertical resolution of 1 km and an integration period of approximately 5 min were achieved in this initial experiment. Finally, a multiple frequency technique for the simultaneous measurement of both temperature and Doppler wind profiles is discussed.

Bills, Richard E.↗

Displacement Compensation of Temperature Probe Data

Analysis of temperature data from a probe in a vertical Bridgman furnace growing germanium crystals revealed a displacement of the temperature profile due to conduction error. A theoretical analysis shows that the displacement compensation is independent of local temperature gradient. A displacement compensation value should become a standard characteristic of temperature probes used for temperature profile measurements.

Welch, Christopher S.↗

Is T/e/ equal to T/n/ at the heights of 100 to 120 km

Low and midlatitude lower E-region electron temperature profiles which were obtained by means of an in situ probe were collected. Profiles which are discussed here cover the heights of 90-120 km and measurement reliability at these heights is discussed mainly in terms of electrode contamination and aerodynamical heating. Although measurement errors might exist in some of the electron temperature profiles, it is conclusively shown that daytime electron temperature is very often much higher than the possible neutral temperature and T(e) is rarely equal to T(n).

Oyama, K. I.↗

The ill-posed nature of the satellite temperature retrieval problem and the limits of retrievability

The inverse problem of satellite temperature profile retrieval is well known to be ill-posed. This means that not only is a vertical temperature profile solution not unique, but that two solutions can be very different from each other. A set of atmosphere-like, and true atmospheric examples of significantly dissimilar inverse solutions, were sought and found, using an 11-channel simulated HIRS sounding radiometer. Using the Riemann-Lebesgue Lemma for guidance, it is shown that simultaneous, numerical solutions of an atmospheric character may differ by as much as 10 K between 10-1000 mb. However, an empirical search for dissimilar solutions in the natural atmosphere reveals an extremely low probability of finding two significantly different RAOBs which produce radiance measurements whose differences cannot be resolved by the satellite radiometer. The empirical results are used to derive a first estimate of the limits of retrievability, analogous to the limits of predictability derivable from the ill-posed nature of the numerical weather prediction problem.

Thompson, Owen E.↗

Two-frequency lidar technique for mesospheric Na temperature measurements

This paper describes a new two-frequency lidar for measuring Na temperature profiles. The laser oscillator is tuned to the two operating frequencies by observing the Doppler-free structure of the Na D2 fluorescence spectrum in a vapor cell. The lidar technique and initial observations of the temperature profile between 82 and 102 km are described. Absolute temperature accuracies at the Na layer peak of better than + or - 3 K with a vertical resolution of 1 km and an integration period of approximately 5 min were achieved.

She, C. Y.↗

Developing Dual Polarization Applications For 45th Weather Squadron's (45 WS) New Weather Radar: A Cooperative Project With The National Space Science and Technology Center (NSSTC)

A new weather radar is being acquired for use in support of America s space program at Cape Canaveral Air Force Station, NASA Kennedy Space Center, and Patrick AFB on the east coast of central Florida. This new radar includes dual polarization capability, which has not been available to 45 WS previously. The 45 WS has teamed with NSSTC with funding from NASA Marshall Spaceflight Flight Center to improve their use of this new dual polarization capability when it is implemented operationally. The project goals include developing a temperature profile adaptive scan strategy, developing training materials, and developing forecast techniques and tools using dual polarization products. The temperature profile adaptive scan strategy will provide the scan angles that provide the optimal compromise between volume scan rate, vertical resolution, phenomena detection, data quality, and reduced cone-of-silence for the 45 WS mission. The mission requirements include outstanding detection of low level boundaries for thunderstorm prediction, excellent vertical resolution in the atmosphere electrification layer between 0 C and -20 C for lightning forecasting and Lightning Launch Commit Criteria evaluation, good detection of anvil clouds for Lightning Launch Commit Criteria evaluation, reduced cone-of-silence, fast volume scans, and many samples per pulse for good data quality. The training materials will emphasize the appropriate applications most important to the 45 WS mission. These include forecasting the onset and cessation of lightning, forecasting convective winds, and hopefully the inference of electrical fields in clouds. The training materials will focus on annotated radar imagery based on products available to the 45 WS. Other examples will include time sequenced radar products without annotation to simulate radar operations. This will reinforce the forecast concepts and also allow testing of the forecasters. The new dual polarization techniques and tools will focus on the appropriate applications for the 45 WS mission. These include forecasting the onset of lightning, the cessation of lightning, convective winds, and hopefully the inference of electrical fields in clouds. This presentation will report on the results achieved so far in the project.

Roeder, W.P.↗

Elemental and charge state composition of the fast solar wind observed with SMS instruments on WIND

The elemental composition and charge state distributions of heavy ions of the solar wind provide essential information about: (1) atom-ion separation processes in the solar atmosphere leading to the 'FIP effect' (the overabundance of low First Ionization potential (FIP) elements in the solar wind compared to the photosphere); and (2) coronal temperature profiles, as well as mechanisms which heat the corona and accelerate the solar wind. This information is required for solar wind acceleration models. The SWICS instrument on Ulysses measures for all solar wind flow conditions the relative abundance of about 8 elements and 20 charge states of the solar wind. Furthermore, the Ulysses high-latitude orbit provides an unprecedented look at the solar wind from the polar coronal holes near solar minimum conditions. The MASS instrument on the WIND spacecraft is a high-mass resolution solar wind ion mass spectrometer that will provide routinely not only the abundances and charge state of all elements easily measured with SWICS, but also of N, Mg, S. The MASS sensor was fully operational at the end of 1994 and has sampled the in-ecliptic solar wind composition in both the slow and the corotating fast streams. This unique combination of SWICS on Ulysses and MASS on WIND allows us to view for the first time the solar wind from two regions of the large coronal hole. Observations with SWICS in the coronal hole wind: (1) indicate that the FIP effect is small; and (2) allow us determine the altitude of the maximum in the electron temperature profile, and indicate a maximum temperature of approximately 1.5 MK. New results from the SMS instruments on Wind will be compared with results from SWICS on Ulysses.

Gloeckler, G.↗

Electro-Thermal Simulation Studies of SiC Junction Diodes Containing Screw Dislocations Under High Reverse-Bias Operation

The objective of this work was to conduct a modeling study of SiC P-N junction diodes operating under high reverse biased conditions. Analytical models and numerical simulation capabilities were to be developed for self-consistent electro-thermal analysis of the diode current-voltage (I-V) characteristics. Data from GRC indicate that screw dislocations are unavoidable in large area SiC devices, and lead to changes in the SiC diode electrical response characteristics under high field conditions. For example, device instability and failures linked to internal current filamentation have been observed. The physical origin of these processes is not well understood, and quantitative projections of the electrical behavior under high field and temperature conditions are lacking. Thermal calculations for SiC devices have not been reported in the literature either. So estimates or projections of peak device temperatures and power limitations do not exist. This numerical study and simulation analysis was aimed at resolving some of the above issues. The following tasks were successfully accomplished: (1) Development of physically based models using one- and two-dimensional drift-diffusion theory for the transport behavior and I-V characteristics; (2) One- and two-dimensional heat flow to account for internal device heating. This led to calculations of the internal temperature profiles, which in turn, were used to update the electrical transport parameters for a self-consistent analysis. The temperature profiles and the peak values were thus obtainable for a given device operating condition; (3) Inclusion of traps assumed to model the presence of internal screw dislocations running along the longitudinal direction; (4) Predictions of the operating characteristics with and without heating as a function of applied bias with and without traps. Both one and two-dimensional cases were implemented; (5) Assessment of device stability based on the operating characteristics. The presence of internal non-uniformities, particularly filamentary structures, was probed and demonstrated; (6) Cause and physical origins of filamentary behavior and unstable I-V characteristics were made transparent; (7) It was demonstrated that diodes containing defects would be more prone to thermal breakdown associated with the temperature dependent decrease in the thermal conductivity; and (8) Finally, negative differential resistance (S-shaped NDR) which can potential lead to device instability and filamentary behavior was shown to occur for diodes containing a line of defects such as could be associated with a screw dislocation line.

Joshi, R. P.↗

In-situ two-dimensional temperature measurements using x-ray fluorescence spectroscopy in laminar flames with high silica particle concentrations

X-ray fluorescence spectroscopy (XRF) was used to measure temperatures and study mixing, for the first time in silica particle synthesis flames. Hexamethyldisiloxane (HMDSO) and trimethylsilanol (TMSO) were the particle precursors. A multi-element diffusion burner was used to produce a flat methane flame, and the precursors, dilute in inert gas, were injected via a central jet. Krypton was the fluorescent medium at 3.2 % concentration by volume. Scans with Kr in the central flow and not in the main flow were made to assess the mixing effects between the central and main gas flows. When HMDSO or TMSO were added, a secondary diffusion flame formed between the jet and the main methane flame. The results revealed a dramatic change in the centerline temperature profile of the jet gases when HMDSO or TMSO were added. The main methane flame stoichiometry also affected the temperature profiles. The results show HMDSO and TMSO reactions are initiated in a lowtemperature and low-oxygen concentration region of the jet where thermal decomposition is not expected to be significant. Reaction of the particle precursors is therefore attributed to radical transport from the main methane flame. In the current work, particle number densities of up to 270 g/m 3 locally are estimated. Thus, the study also demonstrates the capability of the XRF technique for high spatial fidelity measurements in flames with high concentrations of condensed-phase particles, leveraging the attribute that the XRF signal is generally not impacted by condensed-phase interferences. In conclusion, the observations and data obtained in this study inform likely reaction pathways for this important class of siloxane compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temperature-moisture biases in ECMWF analyses based on clear sky longwave simulations constrained by SSMI and MSU measurements and comparisons to ERBE estimates

Clear sky longwave radiation fluxes for the summer of 1988 and winter of 1989 have been simulated with a radiative transfer model that includes detailed treatment of atmospheric gas absorption. The input data to the model are humidity and temperature profiles from European Center for Medium-Range Weather Forecasts (ECMWF) analyses and surface temperature measurements from the International Satellite Cloud Climatology Project. To reduce the inherent uncertainties in humidity profiles, the ECMWF moisture fields have been adjusted, based on the climatological relationship between the moisture profile and total precipitable water (PW), so that the ECMWF PW is equal to that derived from Special Sensor Microwave Imager (SSMI) data. SSMI and ECMWF PW patterns are generally similar, but significant differences in magnitude are found in the low latitudes, particularly over the subtropical oceans in the Southern Hemisphere. At the same time the tropospheric brightness temperature (T(sub B)) at 53.74 GHz has been computed using a microwave transfer model with ECMWF temperature and humidity fields as inputs. The comparison of computed T(sub B) with the Microwave Sounding Unit (MSU) channel 2 T(sub B) revealed differences larger than 1.5 K over most of the oceans, suggesting that the ECMWF model atmosphere has a cold bias. Maximum biases greater than 3 K are found in low latitudes. After removing the bias from the ECMWF temperature field, a new set of temperature profiles yielding brightness temperature equal to MSU channel 2 T(sub B) has been obtained. Simulation results clearly demonstrate that inclusion of satellite estimates of PW and T(sub B) enhances the accuracy of the clear sky LW flux simulation, substantially reducing the differences from Earth Radiation Budget Experiment (ERBE) estimates. Global averages indicate that the model-derived top-of-atmosphere (TOA) clear sky fluxes from the adjusted moisture and temperature profiles are in very good agreement with satellite-measured ERBE values, differing by only 1.4 W/sq m. By contrast, the calculation using only ECMWF analyses without any adjustments gives a significant underestimation of TOA clear sky fluxes up to 10.7 W/sq m compared to the satellite measurements, suggesting that the constraint method can significantly improve the accuracy in the radiation budget simulation. The results also indicate that the ECMWF-based simulation errors are, at least for the two seasons studied, mainly attributed to the error in the temperature field rather than to errors in the moisture field.

Sohn, Byung-Ju↗

Stress studies in EFG

A computer code which can account for plastic deformation effects on stress generated in silicon sheet grown at high speeds is fully operative. Stress and strain rate distributions are presented for two different sheet temperature profiles. The calculations show that residual stress levels are very sensitive to details of the cooling profile in a sheet with creep. Experimental work has been started in several areas to improve understanding of ribbon temperature profiles and stress distributions associated with a 10 cm wide ribbon cartridge system.

Source record↗

An analytic solution of the radiative transfer equation for a gray scattering atmosphere in motion

We provide a formal analytic solution of the radiative transfer equation for a gray moving atmosphere in a plane parallel geometry. A formal solution in the diffusion and the free-streaming limit is also provided in the case of a spherically extended atmosphere. The formal solutions are written explicitly for scattering atmospheres in which the density and the velocity fields are given by a power law. A self-consistent temperature profile accurate to O(Beta = v/c) is provided for the case in which the absorption or the scattering are temperature independent. The gray extinction temperature profile is considerably simplified in the case of a scattering atmosphere. Steady state flow and homologous expansion are special cases that are considered in detail.

Pistinner, Shlomi↗

Development and Validation of MALAMUTE model for Electric Field Assisted Sintering of Structural Materials

Fusion power plant designs feature extreme material performance requirements for structural material candidates. In addition to conventional alloys, more advanced composites and oxide dispersion strengthened (ODS) alloys are being explored, however, achieving the desired microstructures to maximize performance using traditional manufacturing methods can be challenging. The advanced manufacturing (AM) electric field-assisted sintering (EFAS) technique offers improved control over the final microstructure through higher heating and cooling rates and moderate pressures. Modeling and simulation tools show promise in elucidating the process-structure-property-performance (PSPP) correlation for AM-produced parts, including the EFAS process. An inherently multiscale process, the EFAS technique aligns well with the multiscale modeling capability of the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE)[cite]. We present here an electro-thermo-mechanical approach to modeling the EFAS process using the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) code. Prediction of the field and gradient distributions across the EFAS tooling is required to accurately describe the conditions for the lower-scale microstructural evolution models. In this work we present the MALAMUTE model developed to predict the electrical potential, temperature, and mechanical stress distribution across the EFAS graphite tooling and part at the larger engineering-scale. Validation of the MALAMUTE engineering-scale model is completed using data from experimental densification and pre-densified runs of iron powder via EFAS at 1000oC. These runs were conducted using a Thermal Technology DCS-5 EFAS system. Data collected during the experiment runs include the direct current (DC) supplied to the graphite tooling, the temperature of the graphite tooling as measured with a pyrometer, and the force applied to the top of the graphite tooling stack, and the data were recorded every 10 seconds. Our validation approach used the current and force data from the EFAS run as boundary condition inputs to the MAMALUTE simulation; the temperature data were used to evaluate the MALAMUTE EFAS model prediction. Results of the MALAMUTE simulations are employed to connect the external pyrometer temperature measurement to the temperature profile across the part undergoing consolidation. We investigate the impact of material property variation and mesh deformation on the temperature profile as predicted by MALAMUTE. We conclude by highlighting projects where the MALAMUTE EFAS modeling and simulation capabilities will be used to assist experimental design.

36 - MATERIALS SCIENCE↗

Temperature determination of shock layer using spectroscopic techniques

Shock layer temperature profiles are obtained through analysis of radiation from shock layers produced by a blunt body inserted in an arc jet flow. Spectral measurements of N2(+) have been made at 0.5 inch, 1.0 inch, and 1.4 inches from the blunt body. A technique is developed to measure the vibrational and rotational temperatures of N2(+). Temperature profiles from the radiation layers show a high temperature near the shock front and decreasing temperature near the boundary layer. Precise temperature measurements could not be made using this technique due to the limited resolution. Use of a high resolution grating will help to make a more accurate temperature determination. Laser induced fluorescence technique is much better since it gives the scope for selective excitation and a better spacial resolution.

Akundi, Murty A.↗