SEARCH · Search NASA

Results for “Temperature Impact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Optimizing the Orientation of Solar Photovoltaic Systems Considering the Effects of Irradiation and Cell Temperature Models with Dust Accumulation

To cope with the growing installation capacities of solar photovoltaic (PV) systems in desert areas, it is necessary to revisit the energy production models and the optimal angles of PV panels given the significant impacts of ambient temperature, wind speed, dust accumulation, and cleaning frequency. In this study, these four factors are examined for four PV technologies (polycrystalline, microcrystalline, monocrystalline, and thin-film) at three cities in Jordan, Egypt, and Tunisia using precise ground-level meteo-solar measurements. Different models are compared to estimate the diffuse irradiance, as well as account for the effects of operating temperature, wind speed, and dust accumulation on energy production and optimal tilt and azimuth angles of the panels. The results reveal 1.5 % higher energy production estimates using the isotropic model, compared to the anisotropic model in the summer months. Considering the cooling effect of wind speed decreases the operating cell temperature drops by up to 7.05 % for thin film panels. The annually produced energy decreases by 24 % when the panels are cleaned bi-monthly. When the dust accumulation rate doubles, the energy production decreases by ~10 % for all studied cases. Also, the variations in optimal tilt and azimuth angles with dust accumulation rate are within ~3.0 degrees .

14 SOLAR ENERGY↗

NASA NTRS2018

Impact Study of the Assimilation of Surface Sensitive Microwave Radiances in the GEOS

The aim of this study is to investigate the feasibility of assimilating low frequency microwave observations from different satellite Microwave radiometers such as the Advanced Microwave Sounding Unit-A (AMSU-A). These observations are relevant to the description of air temperature, humidity, and surface parameters such as ocean surface temperature. Their assimilation into Goddard Earth Observing System (GEOS) modeling and assimilation system helps better constrain models in regions where very few observations are assimilated. In recent years, Channels 1â€“4 and 15 have not been assimilated in GEOS because of their large sensitivities to uncertain surface parameters such as emissivity and skin temperature. Here, the impact of using different channels will be discussed. Also we investigate the validity of the emissivity model in these channels over ocean and sea ice.Radiative transfer calculations necessary for the assimilation of satellite radiances are performed using the Community Radiative Transfer Model (CRTM). The CRTM performs forward radiative transfer calculations of brightness temperature from atmospheric profiles (temperature, moisture, and ozone) and surface characteristics. Additionally, the CRTM calculates the Jacobians of brightness temperature with respect to the input . The Jacobians are for the inversion of these radiances within the Gridpoint Statistical Interpolation (GSI) analysis system. Here, For direct assimilation of the radiance observations, the interface between GSI and CRTM, is slightly modified. Finally, we validate the assimilation results, and discuss the impact of each channels in detail.

Ebrahimi, Hamideh↗

DOE OSTI2022

Assessment of SCALE and MELCOR for a generic pebble bed fluoride high-temperature reactor

This paper presents the development and application of SCALE and MELCOR models for a fluoride salt-cooled high-temperature reactor (FHR) based on publicly available specifications. SCALE version 6.3beta15 was used to generate power distributions and decay heat curves, and MELCOR version 2.2.18019 was used to calculate the thermal hydraulic response of an assumed FHR primary system. Here, an approach was developed for determining the equilibrium state of the core using depletion of a core slice model and blending of fuel compositions at different burnups to provide three-dimensional fuel composition in the core. Results compared between a core with entirely fresh fuel and one with an equilibrium fuel composition revealed that the equilibrium core led to lower steady-state temperatures but slower cooldown during a loss of flow accident (LOFA). A sensitivity study was then conducted to explore the transient response of our FHR system to variations in thermal hydraulic parameters of the system using the equilibrium core. The inlet temperature, graphite thermal conductivity, and SCRAM time all provided significant control over peak fuel and coolant temperatures. Uncertainties in radionuclide decay data in SCALE were used to perform a decay heat sensitivity study, and we found that uncertainties in decay heat led to negligible impact on peak temperatures during the course of the transient. In all cases evaluated, the observed peak fuel temperatures remained approximately 700 K below anticipated failure limits for the LOFA.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS2012

Detection Thresholds of Falling Snow from Satellite-Borne Active and Passive Sensors

Precipitation, including rain and snow, is a critical part of the Earth's energy and hydrology cycles. Precipitation impacts latent heating profiles locally while global circulation patterns distribute precipitation and energy from the equator to the poles. For the hydrological cycle, falling snow is a primary contributor in northern latitudes during the winter seasons. Falling snow is the source of snow pack accumulations that provide fresh water resources for many communities in the world. Furthermore, falling snow impacts society by causing transportation disruptions during severe snow events. In order to collect information on the complete global precipitation cycle, both liquid and frozen precipitation must be collected. The challenges of estimating falling snow from space still exist though progress is being made. These challenges include weak falling snow signatures with respect to background (surface, water vapor) signatures for passive sensors over land surfaces, unknowns about the spherical and non-spherical shapes of the snowflakes, their particle size distributions (PSDs) and how the assumptions about the unknowns impact observed brightness temperatures or radar reflectivities, differences in near surface snowfall and total column snow amounts, and limited ground truth to validate against. While these challenges remain, knowledge of their impact on expected retrieval results is an important key for understanding falling snow retrieval estimations. Since falling snow from space is the next precipitation measurement challenge from space, information must be determined in order to guide retrieval algorithm development for these current and future missions. This information includes thresholds of detection for various sensor channel configurations, snow event system characteristics, snowflake particle assumptions, and surface types. For example, can a lake effect snow system with low (approx 2.5 km) cloud tops having an ice water content (IWC) at the surface of 0.25 g / cubic m and dendrite snowflakes be detected? If this information is known, we can focus retrieval efforts on detectable storms and concentrate advances on achievable results. Here, the focus is to determine thresholds of detection for falling snow for various snow conditions over land and lake surfaces. The results rely on simulated Weather Research Forecasting (WRF) simulations of falling snow cases since simulations provide all the information to determine the measurements from space and the ground truth. Sensitivity analyses were performed to better ascertain the relationships between multifrequency microwave and millimeter-wave sensor observations and the falling snow/underlying field of view. In addition, thresholds of detection for various sensor channel configurations, snow event system characteristics, snowflake particle assumptions, and surface types were studied. Results will be presented for active radar at Ku, Ka, and W-band and for passive radiometer channels from 10 to 183 GHz.

Gail Skofronick-Jackson↗

NASA NTRS2012

Structural Health Monitoring with Fiber Bragg Grating and Piezo Arrays

Structural health monitoring (SHM) is one of the most important tools available for the maintenance, safety, and integrity of aerospace structural systems. Lightweight, electromagnetic-interference- immune, fiber-optic sensor-based SHM will play an increasing role in more secure air transportation systems. Manufacturers and maintenance personnel have pressing needs for significantly improving safety and reliability while providing for lower inspection and maintenance costs. Undetected or untreated damage may grow and lead to catastrophic structural failure. Damage can originate from the strain/stress history of the material, imperfections of domain boundaries in metals, delamination in multi-layer materials, or the impact of machine tools in the manufacturing process. Damage can likewise develop during service life from wear and tear, or under extraordinary circumstances such as with unusual forces, temperature cycling, or impact of flying objects. Monitoring and early detection are key to preventing a catastrophic failure of structures, especially when these are expected to perform near their limit conditions.

Black, Richard J.↗

NASA NTRSDate not supplied

Assessment of Using Ideal Gas for Predicting Boattail Flow at Cryogenic Temperatures

The applicability of using ideal gas assumptions to simulate high Reynolds number experimental data that was obtained at cryogenic temperatures is examined. Flow over an axisymmetric nozzle boattail model was calculated using reference temperatures of 117 K and 300 K and at Reynolds numbers from 50 to 200 million per meter. From the testing perspective, pressure, compression factor, and isentropic coefficients calculated using one-dimensional real gas equations are used to examine the departure of cryogenic flow from ideal gas flow across the range of temperatures and potential impacts on measured aerodynamic data. Solutions developed using ideal gas assumptions in a three-dimensional Navier-Stokes code are compared with experimental data obtained at cryogenic temperatures at two unit Reynolds numbers at freestream Mach numbers of 0.6 and 0.9. Results for several one- and two-equation turbulence models are shown. Predicted pressure coefficient distributions along the nozzle boattail differed from experimental data between 8% to less than 0.5% depending on the turbulence model and Mach number. The greatest discrepancy occurred in the level of static pressure recovery in the recompression region where the flow was separated. Solutions using warm and cryogenic freestream temperatures predicted similar boattail pressure distributions at the same unit Reynolds number.

Nozzle↗

NASA NTRSDate not supplied

Assessment of Using Ideal Gas for Predicting Boattail Flow at Cryogenic Temperatures

Nozzle↗

NASA NTRS2007

Impact of MODIS High-Resolution Sea-Surface Temperatures on WRF Forecasts at NWS Miami, FL

Over the past few years,studies at the Short-term Prediction Research and Transition (SPoRT) Center have suggested that the use of Moderate Resolution Imaging Spectroradiometer (MODIS) composite sea-surface temperature (SST) products in regional weather forecast models can have a significant positive impact on short-term numerical weather prediction in coastal regions. The recent paper by LaCasse et al. (2007, Monthly Weather Review) highlights lower atmospheric differences in regional numerical simulations over the Florida offshore waters using 2-km SST composites derived from the MODIS instrument aboard the polar-orbiting Aqua and Terra Earth Observing System satellites. To help quantify the value of this impact on NWS Weather Forecast Offices (WFOs), the SPoRT Center and the NWS WFO at Miami, FL (MIA) are collaborating on a project to investigate the impact of using the high-resolution MODIS SST fields within the Weather Research and Forecasting (WRF) prediction system. The scientific hypothesis being tested is: More accurate specification of the lower-boundary forcing within WRF will result in improved land/sea fluxes and hence, more accurate evolution of coastal mesoscale circulations and the associated sensible weather elements. The NWS MIA is currently running the WRF system in real-time to support daily forecast operations, using the National Centers for Environmental Prediction Nonhydrostatic Mesoscale Model dynamical core within the NWS Science and Training Resource Center's Environmental Modeling System (EMS) software; The EMS is a standalone modeling system capable of downloading the necessary daily datasets, and initializing, running and displaying WRF forecasts in the NWS Advanced Weather Interactive Processing System (AWIPS) with little intervention required by forecasters. Twenty-seven hour forecasts are run daily with start times of 0300,0900, 1500, and 2100 UTC on a domain with 4-km grid spacing covering the southern half of Florida and the far western portions of the Bahamas, the Florida Keys, the Straights of Florida, and adjacent waters of the Gulf of Mexico and Atlantic Ocean. Each model run is initialized using the Local Analysis and Prediction System (LAPS) analyses available in AWIPS, invoking the diabatic. "hot-start" capability. In this WRF model "hot-start", the LAPS-analyzed cloud and precipitation features are converted into model microphysics fields with enhanced vertical velocity profiles, effectively reducing the model spin-up time required to predict precipitation systems. The SSTs are initialized with the NCEP Real-Time Global (RTG) analyses at l/12 degree resolution (approx. 9 km); however, the RTG product does not exhibit fine-scale details consistent with its grid resolution. SPoRT is conducting parallel WRF EMS runs identical to the operational runs at NWS MIA in every respect except for the use of MODIS SST composites in place of the RTG product as the initial and boundary conditions over water. The MODIS SST composites for initializing the SPoRT WRF runs are generated on a 2-km grid four times daily at 0400, 0700, 1600, and 1900 UTC, based on the times of the overhead passes of the Aqua and Terra satellites. The incorporation of the MODIS SST composites into the SPoRTWRF runs is staggered such that the 0400UTC composite initializes the 0900 UTC WRF, the 0700 UTC composite initializes the 1500 UTC WRF, the 1600 UTC composite initializes the 2100 UTC WRF, and the 1900 UTC composite initializes the 0300 UTC WRF. A comparison of the SPoRT and Miami forecasts is underway in 2007, and includes quantitative verification of near-surface temperature, dewpoint, and wind forecasts at surface observation locations. In addition, particular days of interest are being analyzed to determine the impact of the MODIS SST data on the development and evolution of predicted sea/land-breeze circulations, clouds, and precipitation. This paper will present verification results comparing the NWS MIA forecasts the SPoRT experimental WRF forecasts, and highlight any substantial differences noted in the predicted mesoscale phenomena.

Case, Jonathan L.↗

DOE OSTI2024

Accelerating CO2 Storage Site Characterization through a New Understanding of Favorable Formation Properties and the Impact of Core-Scale Heterogeneities

CO2 sequestration in deep geologic formations can permanently reduce atmospheric CO2 emissions and help to abate climate change. Target formations must undergo a time- and resource-intensive site evaluation process, assessing storage capacity, environmental safety, and suitability for CO2 trapping via reactive transport models based on data from a limited number of core samples. As such, simulations are often simplified and omit heterogeneities in formation properties that may be significant but are not well understood. To facilitate more rapid site assessment, this work first defines the aquifer properties of favorable storage formations through the analysis of promising and active storage sites. Data show quartz is the most prevalent formation mineral with carbonate minerals, highly reactive with injected CO2, present in over 75% of formations. Porosity and permeability data are highly clustered at 10–30% and 10–1000 mD. Field-scale reactive transport simulations are then constructed and used to analyze CO2 trapping efficiency. The models consider porosity and carbonate mineral heterogeneity as well as the impacts of typical temperature gradients. Simulated sequestration efficiencies are compared to results from a comparable homogenous model to understand the implications of aquifer non-uniformities. The results show a lower sequestration efficiency in the homogeneous model during the injection phase. During the post-injection phase, the homogenization of porosity and carbonate mineralogy results in a higher sequestration efficiency. Incorporating the temperature gradient also increases the sequestration efficiency. Importantly, the maximum deviation between the homogeneous and heterogeneous simulations at the end of the 50-year study period is only ~10%. Larger impacts may be incurred for properties outside the defined, promising ranges suggested here.

Environmental Sciences & Ecology↗

NASA NTRS1987

A VAS-numerical model impact study using the Gal-Chen variational approach

Numerical experiments to assess the impact of incorporating temperature data from the VISSR Atmospheric Sounder (VAS) using the assimilation technique developed by Gal-Chen (1986) modified for use in the Mesoscale Atmospheric Simulation System (MASS) model were conducted. The scheme is designed to utilize the high temporal and horizontal resolution of satellite retrievals while maintaining the fine vertical structure generated by the model. This is accomplished by adjusting the model lapse rates to reflect thicknesses retrieved from VAS and applying a three-dimensional variational that preserves the distribution of the geopotential fields in the model. A nudging technique whereby the model temperature fields are gradually adjusted toward the updated temperature fields during model integration is also tested. An adiabatic version of MASS is used in all experiments to better isolate mass-momentum imbalances. The method has a sustained impact over an 18 hr model simulation.

Aune, Robert M.↗

NASA NTRS1992

Post impact compressive strength in composites

Presented in this paper are the plan, equipment, procedures, and findings of an experimental investigation of the tolerance to low velocity impact of a graphite epoxy (AS4/3501-6) and graphite bismaleimide (M6/CYCOM3100) advanced composites. The applied impacts were governed by the Air Force Guide Specification 87221. Specimens of each material system having a common nominal layup (10% 0 deg; 80% +/-45 deg; 10% 90 deg), a common 7 inch (17.78 cm) by 10 inch (25.40 cm) size, five different thicknesses (9, 26, 48, 74, and 96 plies), and ambient moisture content were impacted and strength tested at room temperature. Damaged areas and post impact compression strengths (PICS) were among the most significant findings obtained. While the undamaged per ply compression strength of both materials is a strong function of laminate thickness, the per ply PICS is not. The average difference in per ply PICS between the two material systems is about seven percent. Although a smaller percentage of the applied kinetic energy was absorbed by the Gr/BMI than by the Gr/Epoxy composites, larger damaged areas were produced in the Gr/BMI than in Gr/Epoxy. Within the limitations of this investigation, the Gr/BMI system seems to offer no advantage in damage tolerance over the Gr/Epoxy system examined.

Demuts, Edvins↗

NASA NTRS2012

Collisional Processing of Comet and Asteroid Surfaces: Velocity Effects on Absorption Spectra

A new paradigm has emerged where 3.9 Gyr ago, a violent reshuffling reshaped the placement of small bodies in the solar system (the Nice model). Surface properties of these objects may have been affected by collisions caused by this event, and by collisions with other small bodies since their emplacement. These impacts affect the spectrographic observations of these bodies today. Shock effects (e.g., planar dislocations) manifest in minerals allowing astronomers to better understand geophysical impact processing that has occurred on small bodies. At the Experimental Impact Laboratory at NASA Johnson Space Center, we have impacted forsterite and enstatite across a range of velocities. We find that the amount of spectral variation, absorption wavelength, and full width half maximum of the absorbance peaks vary non-linearly with the velocity of the impact. We also find that the spectral variation increases with decreasing crystal size (single solid rock versus granular). Future analyses include quantification of the spectral changes with different impactor densities, temperature, and additional impact velocities. Results on diopside, fayalite, and magnesite can be found in Lederer et al., this meeting.

Lederer, S. M.↗

NASA NTRS2012

Improved Wide Operating Temperature Range of LiNiCoAiO2-based Li-ion Cells with Methyl Propionate-based Electrolytes

Demonstration of wide operating temperature range Li-ion electrolytes Methyl propionate-based wide operating temperature range electrolytes were demonstrated to provide dramatic improvement of the low temperature capability of Quallion prototype Li-ion cells (MCMB-LiNiCoAlO2). Some formulations were observed to deliver over 60% of the room temperature capacity using a 5C rate at - 40oC !! Represents over a 4-fold improvement over the baseline electrolyte system. Demonstrated operational capability of a number of systems over a wide temperature range (-40 to +70 C) Demonstrated reasonably good long term cycle life performance at high temperature (i.e., at +40deg and +50 C) A number of formulations containing electrolytes additives (i.e., FEC, VC, LiBOB, and lithium oxalate) have been shown to have enhanced lithium kinetics at low temperature and promising high temperature resilience. Demonstrated good performance in larger capacity (12 Ah) Quallion Li-ion cells with methyl propionate-based electrolytes. Current efforts focused upon performing life studies and the impact upon low temperature capability.

Li-ion electrolytes↗

DOE OSTI2022

Real-time sensor measurements to evaluate impacts of load cycling on high-temperature fire-side corrosion in a PC boiler

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

NASA NTRS1980

Effect of temperature on composite sandwich structures subjected to low velocity impact

The effect of low velocity projectile impact on sandwich-type structural components was investigated. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, the dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failure in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension-and compression-loaded laminates. The specific-strengths and -modulii for the various laminates tested are also given.

Sharma, A. V.↗

DOE OSTI2025

Expanding Parameter Space to Enable Low-Temperature Synthesis of Crystalline Indium Phosphide Quantum Dots

Established methods to synthesize indium phosphide quantum dots (QDs) require high temperatures (>180 °C) to make high-quality material for optoelectronic applications. Nonpolar solvent environments are overwhelmingly used in InP QD synthesis to reach the necessary high temperatures and for compatibility with the reactive precursors. In this study, we explored InP QD synthesis in polar aprotic solvent environments to dramatically decrease the temperature required for InP crystallization by imparting ionicity to the precursors and stabilizing charged reaction intermediates. A custom air-free 96- well plate setup was employed to identify key factors impacting low-temperature QD formation, including an increased percentage of polar solvent, carboxylic acid choice, and inclusion of polar additives. Guided by these insights, we developed a synthesis of crystalline, green-emitting InP QDs at 60 °C in a toluene-dimethylformamide mixture. Here's, the QDs withstood established Zn 2+ and HF surface treatments, which increased the photoluminescence quantum yield to 25%. Additionally, we demonstrated the rapid synthesis of quasi-wurtzite InP QDs at room temperature in a polar solvent environment using an acid-free indium myristate precursor.

absorption↗

NASA NTRS2013

Arcjet Testing of Micro-Meteoroid Impacted Thermal Protection Materials

There are several harsh space environments that could affect thermal protection systems and in turn pose risks to the atmospheric entry vehicles. These environments include micrometeoroid impact, extreme cold temperatures, and ionizing radiation during deep space cruise, all followed by atmospheric entry heating. To mitigate these risks, different thermal protection material samples were subjected to multiple tests, including hyper velocity impact, cold soak, irradiation, and arcjet testing, at various NASA facilities that simulated these environments. The materials included a variety of honeycomb packed ablative materials as well as carbon-based non-ablative thermal protection systems. The present paper describes the results of the multiple test campaign with a focus on arcjet testing of thermal protection materials. The tests showed promising results for ablative materials. However, the carbon-based non-ablative system presented some concerns regarding the potential risks to an entry vehicle. This study provides valuable information regarding the capability of various thermal protection materials to withstand harsh space environments, which is critical to sample return and planetary entry missions.

Agrawal, Parul↗

DOE OSTI2023

An Active and Resilient Bilayer Oxygen Electrode for Intermediate Temperature Reversible Solid Oxide Cells

High temperature solid oxide cells (SOCs) have intrinsic advantage in efficiency over conventional internal combustion engines for power generation and low-temperature electrolysis cells for H2 production. This efficiency advantage could potentially lead to cost saving and emission reduction. However, commercialization of the current SOCs technology is hindered by its poor durability. One major component with the durability issue is oxygen electrode (OE). For example, the durability of OEs can be negatively affected by the gaseous Cr-species originated from the air oxidation of high-temperature alloy interconnect. For electrolysis operation, on the other hand, delamination of OE from electrolyte, particularly at high current densities, has been identified as a major cause for the performance degradation. Therefore, developing robust and active OEs is of critical importance to SOC technology. WE have previously demonstrated a new bilayer OE with strong activity and stability. Here in this presentation, we present recent results of electrochemical characterization on bilayer OE operating under both fuel cell and electrolysis modes. We will first show the optimization of bilayer OE in terms of thickness, morphology, and calcination temperature and their impacts on cell area specific resistance (ASR). With three-electrode symmetric cell configuration, we also show the results of charge transfer ASR of bilayer OE as a function of current density, temperature, and time in different atmospheres. The results are further compared with the baseline OE (LSCF+GDC) to demonstrate the advantage of bilayer OE.

Huang, Kevin↗