Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Advanced polymer impregnation and pyrolysis (PIP) of SiOC-based ceramic matrix composites (CMCs)

Silicon carbide (SiC) ceramic matrix composites (CMCs) are valued for their high-temperature properties, making them ideal for harsh environments. However, conventional polymer impregnation and pyrolysis (C-PIP) often result in porous composites and require numerous cycles for densification. This study introduces the advanced PIP (A-PIP) method using a crosslinked polycarbosiloxane (PCS) precursor to enhance densification efficiency. Five SiC CMCs were fabricated using C-PIP and A-PIP, with variations in fiber reinforcement and fiber coatings. A-PIP achieved up to 19 % higher density and 78 % lower porosity in 79–86 % less processing time compared to C-PIP. Moreover, SiC-SiOC composites with boron nitride-coated fibers showed significant improvements in tensile strength (11 MPa to 134 MPa) and strain at maximum strength (0.01–0.11 %), underscoring the role of weak fiber-matrix interfaces. In conclusion, these results demonstrate A-PIP's potential to produce dense, low-porosity SiC CMCs more efficiently, significantly reducing manufacturing time and costs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High speed manufacturing of aluminum alloy 7075 tubing by Shear Assisted Processing and Extrusion (ShAPE)

Shear assisted processing and extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at speeds up to 12.2 m/min. This is in comparison to 2.0 m/min which is generally the limit for conventionally extruded 7075. The increased speed is primarily attributed to more extensive shear deformation, compared to conventional extrusion, which results in a high density of low angle grain boundaries that facilitate continued deformation and delay the onset of surface tearing. Mechanical testing after heat treating to the T6 condition gave an ultimate tensile strength of 565.3 ± 4.6 MPa, yield strength of 495.7 ± 8.7 MPa, and elongation of 16.8 ± 0.8%. Strength values exceed the ASTM minimum standard and are on par with ASM typical values, while elongation was substantially improved compared to 7 and 11% for the ASTM and ASM values respectively. Finally, it was observed that low temperature extrusion at 341 °C and 40 rpm gave superior material properties in the T6 condition compared to high temperature extrusion at 441 °C and 120 rpm due to variances in nanoscale second phase size and distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction extrusion of ODS copper rod made from powder

Meters-long oxide dispersion strengthened copper rods were manufactured directly from powder by a single-step process, called friction extrusion. The average grain size was 880 nm, which was refined 40 times from powder precursor due to extensive shear deformation. Meanwhile, the average size of alumina particles was 60 nm which retains a decent oxide dispersion strengthening. Here, mechanical properties, including hardness, tensile strength, and ductility, were tested and found to have better or similar values than conventional sintered-then-extruded oxide dispersion strengthened copper materials. The presented technique promises a convenient avenue for the fabrication of oxide dispersion strengthened copper from powder.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A process optimization framework for laser direct energy deposition: Densification, microstructure, and mechanical properties of an Fe-Cr alloy

Laser Direct Energy Deposition (DED) is a metal additive manufacturing technique with the ability to fabricate large and complex parts through deposition of metal powders. However, achieving high-density parts and targeted build heights using DED can be challenging due to the large number of highly sensitive process variables. This work proposes a robust fabrication parameter optimization framework to generate process maps for primary parameters in DED, including laser power, scan speed, mass flow rate, hatch spacing, and layer height. Simple single-track experiments were utilized to map out the parameter space, and a combination of geometric criteria for hatch spacing and layer height were proposed to determine parameter sets that achieve both targeted build heights and mitigate porosity formation. Using this framework, specimens with >99 % density and consistent mechanical properties were successfully fabricated over a wide range of process parameters for an Fe-9wt.%Cr (Fe9Cr) alloy, a surrogate for radiation damage-resistant reduced activation ferritic/martensitic (RAFM) steels. Processing these materials using DED is of particular interest in the development of plasma facing components for nuclear fusion applications. The microstructure and mechanical properties of as-printed Fe9Cr were characterized using optical and electron microscopy, X-ray diffraction, and uniaxial tensile tests. As-printed Fe9Cr displayed ~25 % elongation and ultimate tensile strengths of up to 475 MPa which is comparable to similar wrought alloys. Finally, the proposed framework will allow for accelerated DED parameter optimization for novel alloy systems, as well as open the possibility for local microstructure control while simultaneously mitigating defect formation.

42 ENGINEERING↗
DOE OSTI2023

Effect of printing parameters on 3D-printed carbon fiber-reinforced polymer composites under magnetic field control

Magnetic field controlled (MFC) 3D printing is a promising method for realizing the intelligent control of the structural performance of carbon fiber-reinforced plastic (CFRP) composites by adjusting the fiber orientation during the printing process. However, few studies have focused on the influence of the printing parameters on the magnetic control of the fiber direction. Therefore, in this study, the mechanical properties and internal fiber distributions of MFC 3D-printed samples of CFRP composites with 10 wt% fiber content, which were printed at different speeds and layer thicknesses, were investigated. Subsequently, the effects of the fiber content on the mechanical properties and fiber distribution of the MFC 3D-printed samples were studied. Furthermore, the origin of fiber fracture was evaluated through observation and analysis of the fracture section using scanning electron microscopy. The fiber orientation could be well adjusted under the action of a magnetic field and adjustment of printing parameters, thereby improving the tensile strength, young's modulus significantly with slightly decrease of fracture elongation. The recommended parameter combinations (printing speed and layer thickness) were 40 mm/s and 0.2 mm for 10 wt% fiber content CFRP composites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗
DOE OSTI2022

Quantitative assessment of particle dispersion in polymeric composites and its effect on mechanical properties

In this work, an automated image analysis tool is developed to establish quantitative correlations between the particle/cluster size distribution and the mechanical properties of particle reinforced polymer composites (PRPC).This automated image analysis tool is developed within python programming software to process and analyze the microstructural images of the polymerbased composite materials. The spent coffee bean powder (SCBP) reinforced poly-propylene carbonate (PPC) polymer composite with differing wt.% of the filler is selected for the analysis. Detailed statistical analysis of the microstructural images reveals that ‘clustering of clusters’ is also presented in addition to the most commonly reported ‘clustering of particles’, and the distribution of particle/clusters is bimodal. Based on these findings, an effective volume fraction for the filler material is proposed to mainly capture the agglomeration effect. With this effective volume fraction, the standard rule-of-mixture model correctly captures the experimentally measured tensile strength and modulus as a function of filler wt.%. Further, the applicability of this effective volume fraction for other theoretical models is also analyzed. The detailed statistical analysis of the microstructure and the proposed effective volume fraction helps to develop a deeper quantitative understanding of the PRPC than the conventional qualitative correlation of microstructural features with the properties and failure processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition using neutron diffraction and imaging techniques

In a directed energy deposition (DED) process, the energy density deposited into the materials drives the structure and properties. The energy density is influenced by several printing parameters, such as laser power, hatch spacing, scanning speed, etc. In this study, 316L stainless steels samples were fabricated with varying hatch spacing aiming to induce variations in sample microstructure and properties. A combination of techniques including engineering neutron diffraction, neutron computed tomography, and tensile testing, were employed to correlate the structure and macroscopic properties. Porosity was predominantly observed at the bottom of the deposited materials and was effectively reduced by decreased hatch spacing. Correlatively, compressive residual stress was observed at the bottom of the specimens, while internal stress is largely determined by the hatch spacing. The residual stress in general decreases as the hatch spacing decreases. The maximum ultimate tensile strength (UTS) was found to increase from 517.4 to 528.6 MPa with a strain increased from 0.847 to 0.897 as the hatch spacing decreased from 0.45 to 0.42 mm. However, further increase in energy density by reducing the hatch spacing resulted in a significant decrease in UTS (as low as 452 MPa). This work provides new insights from bulk non-destructive techniques into correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition.

316L stainless steel↗
DOE OSTI2021

Mechanistic verification of empirical UO 2 fuel fracture models

Standard UO 2 fuel pellets used in light-water reactors fracture during irradiation due to the large thermal gradient in the radial direction. Over the decades, numerous researchers have explored fuel cracking from experimental and modeling points of view. To date, there have been both empirical and mechanistic approaches to predict the number of fragments that form in UO 2 . The empirical models only consider maximum power and burnup as inputs. Existing mechanistic approaches for normal operation have not accounted for irradiation effects. Here, this work employs a mechanistic fuel cracking model using the extended finite element method to explore radial crack formation while including a sensitivity analysis that accounts for the randomization of tensile strength within the fuel, the strength randomization criteria (uniform or volume-weighted Weibull), power ramping rates, computational mesh density, maximum power level, and irradiation (burnup) effects. The results indicate that the uncertainty in this mechanistic modeling approach envelopes the predicted values from three different empirical correlations in almost all cases. This means that, for computationally intensive analyses involving UO 2 fragmentation, the empirical correlations can be used. However, since the mechanistic calculations bound those of the empirical correlations, there is confidence in the applicability of the mechanistic approach developed in this work to generate a correlation for fuel types where limited data exists (e.g., doped-UO 2 , U 3 Si 2 ).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Dynamic data-driven multiscale modeling for predicting the degradation of a 316L stainless steel nuclear cladding material

Here, we have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Gas tungsten arc welding and post weld heat treatment effects on microstructure and mechanical property of castable nanostructured alloy steel

Here, this paper details the first study of castable nanostructured alloy (CNA) steel gas tungsten arc weldability and the post-weld heat treatment (PWHT) effects. Effects of welding heat input, thermal cycles, and PWHT on microstructures, microhardness distributions, room temperature tensile properties, and fracture characteristics are discussed. Results show that CNA steel exhibits excellent weldability (i.e., no indication of welding defects and reasonable tensile properties). The welded joint exhibited heterogeneous microstructures with δ-ferrite as well as large microhardness variation and fluctuation. The welded joint yield and ultimate tensile strengths were similar to those of the base metal, but the elongations decreased by 30 %. However, with normalization and tempering PWHT, the δ-ferrite was eliminated, microstructure was modified, hardness was unified, and joint ductility was restored. The study indicated that the CNA reduced-activation ferritic-martensitic steel owns excellent weldability, and PWHT is needed for the industrial application of welded structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Wood-reinforced composites by stereolithography with the stress whitening behavior

In this study, poplar wood flour at various concentrations (1–10 wt%) is incorporated into a methacrylate-based resin via solution blending to fabricate wood-reinforced composites using stereolithography apparatus (SLA) 3D printing. Differential scanning calorimetry (DSC) along with Fourier transform infrared spectroscopy (FTIR) analysis shows the presence of a small amount of residual monomer in the printed samples. For the printed composites, the glass transition temperature (T g ) from dynamic mechanical analysis (DMA) decreases as more wood flour is incorporated, which indicates an increase in free volume occupied by polymer chains. The tensile strength is improved up to 17.3% from 21.1 MPa (no wood flour) to 24.7 MPa (1.0 wt% wood flour). The highest Young’s modulus reaches 323.8 MPa (2.0 wt% wood flour), which is 1.9-fold of that of the sample without wood flour. Moreover, the composites show “stress whitening” with the addition of wood flour during the uniaxial drawing. Morphology analysis of the tested samples show that the formation of microcraze and microvoids likely causing the stress whitening. This is the first study that demonstrates wood flour can be utilized in SLA 3D printed wood plastic composites (WPC) which can reinforce the printed products with a modest loading amount.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ultrasonic additive manufacturing of zirconium: Pilot results

Ultrasonic additive manufacturing (UAM) was successfully applied to the Zirconium material system to create a three-dimensional component prototype. The UAM process resulted in grain size refinement and significant localized deformation. Electron backscatter diffraction analysis revealed activated slip systems only applicable at high deformation temperatures, while texture analysis showed a decrease in measurable texture of the UAM build in comparison to the initial Zr-foil. Average tensile strengths in the X (sonotrode travel), Y (vibration), and Z (build) directions averaged 435 MPa, 458 MPa, and 359 MPa, respectively, demonstrating the viability of UAM for Zr-based materials. Furthermore, the delamination of some Z specimens along foil boundaries during loading suggests an interplay between interfacial Ti impurities introduced during welding and the spatial dependence of weld quality for this material system.

36 MATERIALS SCIENCE↗
DOE OSTI2020

3D-printing methacrylate/chitin nanowhiskers composites via stereolithography: Mechanical and thermal properties

We report on the mechanical and thermal properties of stereolithography (SLA) 3D-printed methacrylate (MA) resin reinforced by chitin nanowhiskers (CNWs). CNWs were synthesized by acid hydrolysis of crab shell chitin and nanocomposites with 0 wt%, 0.5 wt%, 1.0 wt%, and 1.5 wt% CNWs loading were prepared by slurry compounding method. The obtained CNWs (diameter = 23 ± 5 nm, length = 253 ± 100 nm, and aspect ratio = 11 ± 3) are well dispersed within the bulk of MA at 1.0 wt% loading, implying good interfacial adhesion between the nanofiller and the resin matrix possibly due to hydrogen bonding interactions. The addition of up to 1.0 wt% CNWs to neat MA enhances the tensile strength, strain at break, modulus, and maximum thermal degradation temperatures of the nanocomposites. Moreover, the incorporation of CNWs not only improves the mechanical and thermal properties, but also preserves the excellent resolution and accuracy of 3D-printed MA/CNWs nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

PBI nanofiber mat-reinforced anion exchange membranes with covalently linked interfaces for use in water electrolysers

Anion exchange membranes (AEM) are key components in anion exchange membrane water electrolysers. Recently developed materials are less susceptible to the alkaline degradation of the polymer backbone and quaternary ammonium groups. A remaining challenge is the mechanical stability in contact with hot water and dimensional stability when the temperature of the feed solution changes. One solution is to reinforce membranes with a porous support. Since support materials like PEEK or PTFE have a different swelling behavior than the matrix and no strong interactions with the matrix, voids can form, and gas crossover increases. In this work, we approach this issue by pore filling polybenzimidazole nanofiber mats with the bromomethylated precursor of mTPN, an ultra-stable AEM material. During drying, a covalent interaction between support (PBI amine groups) and matrix (-CH 2 Br) is established. After quaternization, the optimized PBI/mTPN-50.120 composite membrane still shows a high conductivity of 62 mS cm –1 , but 37% reduced length swelling in comparison to the non-reinforced membrane. Tensile strength and Young's modulus increase 17% and 56% to 49 MPa and 680 MPa, respectively. In an electrolyser, a stable voltage of 1.98V at 0.25 A cm –2 was achieved, and no change in membrane resistance was observed over the test time of 200 h (50°C, 1 M KOH, catalysts based on Ni/Fe and Mo).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗