Search NASA⌕ Search

SEARCH · Search NASA

Results for “VELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Development of Hydroxyl Tagging Velocimetry for Low Velocity Flows

Hydroxyl tagging velocimetry (HTV) is a molecular tagging technique that relies on the photo-dissociation of water vapor into OH radicals and their subsequent tracking using laser induced fluorescence. Velocities are then obtained from time-of-flight calculations. At ambient temperature in air, the OH species lifetime is relatively short (<50 μs), making it suited for high speed flows. Lifetime and radicals formation increases with temperature, which allows HTV to also probe low-velocity, high-temperature flows or reacting flows such as flames. The present work aims at extending the domain of applicability of HTV, particularly towards low-speed (<10 m/s) and moderate (<500 K) temperature flows. Results are compared to particle image velocimetry (PIV) measurements recorded in identical conditions. Single shot and averaged velocity profiles are obtained in an air jet at room temperature. By modestly raising the temperature (100-200 degC) the OH production increases, resulting in an improvement of the signal-to-noise ratio (SNR). Use of nitrogen - a non-reactive gas with minimal collisional quenching - extends the OH species lifetime (to over 500 μs), which allows probing of slower flows or, alternately, increases the measurement precision at the expense of spatial resolution. Instantaneous velocity profiles are resolved in a 100degC nitrogen jet (maximum jet-center velocity of 6.5 m/s) with an uncertainty down to 0.10 m/s (1.5%) at 68% confidence level. MTV measurements are compared with particle image velocimetry and show agreement within 2%.

Andre, Matthieu A.↗
NASA NTRS2020

Determining the Shallow Surface Velocity at the Apollo 17 Landing Site

Many studies have been performed to determine the shallow surface velocity model at the Apollo 17 landing site. The Lunar Seismic Profiling Experiment (LSPE) had both an active component with eight explosive packages (EPs) and a passive experiment collecting data at various time intervals. Using the eight EPs, the initial shallow surface velocity model was determined to be 250 m/s in the first layer of depth 248 m, 1200 m/s with a depth of 927 m in the second layer, and 4000 m/s down to a depth of 2 km in the third layer. Have performed variations on this study to produce new velocity models shown. Recent studies have also been reanalyzing the passive LSPE data and have found three different thermal moonquake event types occurring at different times within the lunar day. The current goal of the project is to collocate the thermal moonquakes to physical surface features to determine the breakdown of lunar rocks. However, to locate shallow surface events, an accurate velocity model is needed. Presented a thermal moonquake location algorithm using first order approximation, including surface events only. To improve these approximations, a shallow surface velocity is needed.

Phillips, D.↗
NASA NTRSDate not supplied

Analysis of Nitrogen Shockwave Radiation at Velocity Around 7km/s

In the last decade, the Electric Arc Shock Tube (EAST) facility has been widely used to provide experimental data aiming to validate radiative heating models used for atmospheric entry, mostly at velocities above 9km/s in air. In more recent years, another experimental campaign aimed to look at velocity below 9 km/s and its analysis resulted in a significant improvement of the air kinetic model using new rates found in the literature but discrepancies were still observed, especially for the N2 second positive system. Despite these previous studies, the overall uncertainties related to surface heating for lunar return remain around 50% To reduce these uncertainties, the last experimental campaign at EAST, named test 62, was conducted in pure nitrogen at velocity ranging from 6 to 11 km/s at a freestream pressure of 0.2 Torr to provide more fundamental data on nitrogen. A previous study analyzed the data obtained at a velocity of 10.3 km/s, where atomic radiation is dominant, and provided spatially resolved density measurements of different states of nitrogen. This study will focus on experimental data obtained at shock velocity of 6.88 and 7.15 km/s where molecular nitrogen is expected to be the dominant source of radiation.

Augustin Tibere-Inglesse↗
NASA NTRSDate not supplied

Velocity and Temperature Measurements in High-speed Flows with Naturally Present Dust Particles Using Rayleigh and Mie Scattering

Dust particles and occasional moisture condensations are unavoidable reality of all wind tunnels. On the path to pursue a goal of velocity and temperature measurements in high-speed wind tunnels we have created a tabletop, spectrally resolved, Rayleigh-Mie scattering setup around a small jet fed by ambient and air with different particle concentration to determine the accuracy of the technique. The other reality of a wind tunnel setup is the spurious reflection and scattering of the incident laser beam by solid surfaces (flare light), which contaminates the Rayleigh-Mie scattered light. This is simulated by backgrounds with different reflectivity towards the collection optics. Light from a CW laser is delivered via an optical fiber and the scattered light from a point on the laser path is spectrally resolved using a stabilized Fabry-Perot interferometer, followed by imaging on an EMCCD camera. A model of the combined background glare, Mie scattering, and the Rayleigh spectrum was fitted to the camera image using maximum likelihood estimation. It was observed that the present modeling approach can extract velocity and temperature with reasonable accuracy when the intensity of the Mie scattered light is less than or comparable to that of the Rayleigh scattered light; beyond that error in velocity measurement remains reasonable ±12m/s but the temperature measurement becomes progressively more inaccurate. Increasingly the flare light is found to cause a bias error in velocity. Similar trend is observed in the presence of both the flare light and the Mie scattered light. The setup has provided a set of data for the future improvement of the modeling procedure, and demonstrated that even in the case of large amount of dust particles and large flare light the present technique can provide measurement of velocity with reasonable accuracy.

Rayleigh scattering↗
NASA NTRS2026

Electron Velocity Moments in the Solar Wind. I. Calibration of the Wind 3DP EESA Low Detector

Calibrated measurements of electron velocity distribution functions (VDFs) are necessary to characterize fluid and kinetic processes in weakly collisional and nearly collisionless plasmas such as the solar wind. Therefore, we analyzed 3,996,051 electron VDFs observed by the Wind 3DP thermal electron detector near 1 astronomical unit (au) between January 1, 2005 and November 25, 2017. The data were calibrated for each electron VDF to produce accurate velocity moments in the solar wind. This is the first full solar cycle coverage electron velocity moment dataset in the near-Earth solar wind. Herein (Paper I) we discuss the calibration process/algorithms and the velocity moment constraints, uncertainties, and resulting public dataset. In the second paper (Paper II), we statistically analyze the electron velocity moment dataset.

plasmas↗
DOE OSTI2025

The DESI DR1 Peculiar Velocity Survey: Fundamental Plane Catalogue

Measurements of peculiar velocities in the local Universe are a powerful tool to study the nature of dark energy at low ($z < 0.1$) redshifts. Here we present the largest single set of $z<0.1$ peculiar velocity measurements to date, obtained using the Fundamental Plane (FP) of galaxies in the first data release (DR1) of the Dark Energy Spectroscopic Instrument (DESI). We describe the photometric and spectroscopic selection criteria used to define the sample, as well as extensive quality control checks on the photometry and velocity dispersion measurements. Additionally, we perform detailed systematics checks for the many analysis parameters in our pipeline. Our DESI DR1 catalogue contains FP-based distances and peculiar velocities for $98,292$ unique early-type galaxies, increasing the total number of $z < 0.1$ FP distances ever measured by a factor of $\sim2$. We achieve a precision of $26\%$ random error in our distance measurements which is comparable to previous surveys. A series of companion DESI papers use the distances and peculiar velocities presented in this paper to measure cosmological parameters.

Ross, C. E. [Queensland U.]↗
DOE OSTI2025

A novel ignition model for low velocity impact of heterogeneous explosives based on interacting hot spots

While numerous studies have focused on the ignition of explosives occurring in high velocity impact and the associated shock-to-detonation transition, there has been growing interest in developing computational models focused on low-velocity impact regimes. A predictive low-velocity impact ignition model will be important for analyzing high explosive safety and potential accident scenarios. This work introduces a novel ignition model based on the concept of thermally interacting hot spots to simulate low velocity impacted heterogeneous explosives where observed ignition times are on the order of milliseconds. The model asserts that relevant hot spots are micron-sized, the typical separation between neighboring hot spots is on the order of a hundred microns, and that neighbors interact thermally through heat conduction across the interstitial region between them. To achieve tractable numerical solutions, hot spots are assumed to form a periodic array as opposed to the highly irregular positioning in an actual explosive. This idealization allows a single two hotspot system to characterize the ignition process. Consequently, the model is referred to as the two hot spot Frank-Kamenetskii ignition model. In the present study, hot spots are modeled as constant heat sources terms, but this can be extended to include grain-scale phenomena like frictional heating of micron-sized growing cracks that are confined under high pressure. Because the micron-sized features are below the scale that can be efficiently resolved at a systems level, an efficient subscale scheme based on the Method of Weighted Residuals (MWR) is used to efficiently solve the equations. In conclusion, we carry out numerical examples and analytic predictions illustrating the accuracy and the functioning of the model.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Comparative study between experimental measurements and model predictions of bubble rise velocity in molten LiCl-KCl

This research investigated the shape and rise velocities of gas bubbles (helium, nitrogen, argon, and krypton) in molten LiCl-KCl at 500 °C using a specialized optical visualization apparatus. The apparatus features a custom quartz rectangular prism cell housed in a furnace, enabling the application of the shadowgraph measurement technique. Bubbles with diameters between 0.45 and 3.2 mm were produced via a capillary, and their equivalent diameters and rise velocities were analyzed using high-resolution imaging and centroid tracking algorithms. Important non-dimensional parameters were calculated to characterize behavior. Bubbles with 0.03 < Eo < 1.32, 17 < Re < 718, and Mo order of 10 -11 were generated in the molten LiCl-KCl, revealing that bubbles with diameters less than 1.46 mm remain spherical, whereas those with larger diameters are ellipsoidal. The transition and oscillation onset for bubble shape occurred at larger diameters than those previously observed in air–water systems. Comparative analysis of the gas-molten salt data against existing air–water bubble rise velocity correlations highlighted inaccuracies in predictions, particularly across the different bubble regimes. An existing correlation was calibrated to the molten salt data to improve the bubble velocity predictions. In conclusion, this study contributes essential experimental data for the design and safety evaluation of molten salt reactors and offers insights for the optimization of sparge systems for fission product removal.

Bubble rise velocity↗
DOE OSTI2024

Ion velocity effect governs damage annealing process in defective KTaO 3

Effects of electronic to nuclear energy losses (S e /S n ) ratio on damage evolution in defective KTaO 3 have been investigated by irradiating pre-damaged single crystal KTaO 3 with intermediate energy O ions (6 MeV, 8 MeV and 12 MeV) at 300 K. By exploring these processes in pre-damaged KTaO 3 containing a fractional disorder level of 0.35, the results demonstrate the occurrence of a precursory stage of damage production before the onset of damage annealing process in defective KTaO 3 that decreases with O ion energy. The observed ionization-induced annealing process by ion channeling analysis has been further mirrored by high resolution transmission electron microscopy analysis. In addition, the reduction of disorder level is accompanied by the broadening of the disorder profiles to greater depth with increasing ion fluence, and enhanced migration is observed with decreasing O ion energy. Since S e (~3.0 keV nm –1 ) is nearly constant for all 3 ion energies across the pre-damaged depth, the difference in behavior is due to the so-called 'velocity effect': the lower ion velocity below the Bragg peak yields a confined spread of the electron cascade and hence an increased energy deposition density. Here, the inelastic thermal spike calculation has further confirmed the existence of a velocity effect, not previously reported in KTaO 3 or very scarcely reported in other materials for which the existence of ionization-induced annealing has been reported. In other words, understanding of ionization-induced annealing has been advanced by pointing out that ion velocity effect governs the healing of pre-existing defects, which may have significant implication for the creation of new functionalities in KTaO 3 through atomic-level control of microstructural modifications, but may not be limited to KTaO 3 .

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Numerical modeling and experimental validation of low velocity impact of woven GFRP/CFRP composites

Low-velocity impact of 2D woven glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) composite laminates was studied experimentally and numerically. Hybrid laminates containing blocked layers of GFRP/CFRP/GFRP with all plies oriented at 0° were investigated. Relatively high impact energies were used to obtain full perforation of the laminate in a low-velocity impact setup. Numerical simulations were carried out using the in-house transient dynamics finite element code, Sierra/SM, developed at Sandia National Laboratories. A three-dimensional continuum damage model was used to describe the response of a woven composite ply. Two methods for handling delamination were considered and compared: (1) cohesive zone modeling and (2) continuum damage mechanics. The reduced model size achieved by omission of the cohesive zone elements produced acceptable results at reduced computational cost. Further, the comparison between different modeling techniques can be used to inform modeling decisions relevant to low velocity impact scenarios. The modeling was validated by comparing with the experimental results and showed good agreement in terms of predicted damage mechanisms and impactor velocity and force histories.

36 MATERIALS SCIENCE↗
NASA NTRS1962

VELOCITY REQUIREMENTS FOR THE CORRECTION OF A 24-HOUR ORBIT

An investigation of the amount of velocity or energy required to correct an orbit to a near-perfect, circular, equatorial orbit with a period of one sidereal day. The required velocity is shown to be a function of the satellite position and velocity errors at the time correction is to be performed, as well as certain parameters inherent in the "guidance law." The results in their final form permit computation of the corrective velocity as a function of initial injection cut-off errors and errors arising from perturbative accelerations.

ORBIT↗
NASA NTRS1996

Interferometric Estimation of theThree-Dimensional Ice-Flow Velocity Vector Using Ascending and Descending Passes

Satellite radar interferometry provides an importatn new tool for determining ice-flow velocity. Interferometric measurements made from a single track direction are sensitive only to a single component of the three-dimensional velocity vector. Observations from along thre different track directions would allow the full velocity vector to be determined. A north/south-looking SAR could provide these observations over large portions of the globe but not over large areas of the polar ice sheets. We develop and demonstrate a technique that allows the full three-component velocity vector to be determined from data acquired along two track directions (ascending and descending) under a surface-parallel flow assumption.

interferometry satellite radar interferometry ice-↗
NASA NTRS2011

Safe Maritime Navigation with COLREGS Using Velocity Obstacles

This paper presents a motion planning algorithm for Unmanned Surface Vehicles (USVs) to navigate safely in dynamic, cluttered environments. The proposed algorithm not only addresses Hazard Avoidance (HA) for stationary and moving hazards but also applies the International Regulations for Preventing Collisions at Sea (known as COLREGs). The COLREG rules specify, for example, which vessel is responsible for giving way to the other and to which side of the "stand-on" vessel to maneuver. The three primary COLREG rules were considered in this paper: crossing, overtaking, and head-on situations. For USVs to be safely deployed in environments with other traffic boats, it is imperative that the USV's navigation algorithm obey COLREGs. Note also that if other boats disregard their responsibility under COLREGs, the USV will still apply its HA algorithms to avoid a collision. The proposed approach is based on Velocity Obstacles, which generates a cone-shaped obstacle in the velocity space. Because Velocity Obstacles also specify which side of the obstacle the vehicle will pass during the avoidance maneuver, COLREGs are encoded in the velocity space in a natural way. The algorithm is demonstrated via both simulation and on-water tests.

velocity obstacles↗
NASA NTRS2015

Fuselage-Induced Velocity Model for LRTA, RTA, and HART Fuselages

In order to make the aerodynamic fuselage-rotor interference effects available to comprehensive rotor codes, a simple analytical model of the fuselage-induced velocities within the volume of rotor blade operation above the fuselage is developed here for the following bodies used in wind tunnel experiments: the Large Rotor Test Apparatus (LRTA), the Rotor Test Apparatus (RTA), and the Higher Harmonic Control Aeroacoustic Rotor Test (HART).While the first two are used in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames, California, the third one is used by DLR in the large low-speed facility of the German-Dutch wind tunnel in the Netherlands. The fuselage-induced velocity model is based on parameter identification of isolated fuselage-induced velocity data (computed by means of computational fluid dynamics, CFD) and is intended to be generic enough to be used for real helicopter fuselages as well. The accuracies obtained in reproducing the CFD data show a remaining average error of less or equal 5 of the peak-to-peak induced velocity range, which is considered sufficient for comprehensive code analysis.

HART↗
NASA NTRS2020

Evaluation of a Method to Retrieve Temperature and Wind Velocity Profiles of the Venusian Nightside Mesosphere from Mid-Infrared CO2 Absorption Line Observed by Heterodyne Spectroscopy

We evaluated a method for retrieving vertical temperature and Doppler wind velocity profiles of the Venusian nightside mesosphere from the CO2 absorption line resolved by mid-infrared heterodyne spectroscopy. The achievable sensitive altitude and retrieval accuracy were derived with multiple model spectra generated from various temperature and wind velocity profiles with several noise levels. The temperature profiles were retrieved at altitudes of 70–100 km with a vertical resolution of 5 km and a retrieval accuracy of ±15 K. The wind velocity was also retrieved at an altitude of approximately 85 km with a vertical resolution of 10 km and a retrieval accuracy of ± 25–50 m/s. In addition, we studied an event and applied our method to spectra obtained by the HIPWAC instrument attached to the NASA/IRTF 3-m telescope on May 19–22, 2012. Retrieved wind velocities in a latitude of 33° S at 3:00 LT were interpreted as subsolar-to-antisolar (SS-AS) flows at altitudes of 84 ±6 km and 94 ±7 km, and they were stronger than expected. This result suggested that the transition between the retrograde super rotational zonal (RSZ) wind and SS-AS flow may occur at altitudes below 90 km which previously was predicted to be the transition region. This work provides a basis for our analysis of further observations obtained by a mid-infrared heterodyne spectrometer MILAHI attached to the Tohoku University 60-cm telescope at Haleakalā, Hawaii.

Venus↗
DOE OSTI2025

Comparison of interlaminar damage modeling strategies for hybrid composite/aluminum laminates subjected to low-velocity impact

Low-velocity impact of hybrid metal-composite structures was investigated experimentally and computationally. Composite laminates consisting of 2D woven glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) were joined with a 6061-T6 aluminum plate using an epoxy adhesive. Two variations of the structure were studied; one consisting of all plies oriented at 0° and one consisting of all plies oriented at 45°. A drop tower was used to impact structures at a range of energies, including energies above and below the threshold at which the aluminum layer was perforated. Numerical simulations were implemented using Sierra/SM, an in-house transient dynamics finite element code developed at Sandia National Laboratories. A Hosford plasticity model was used to describe the response of the aluminum layer. A newly implemented orthotropic continuum damage mechanics (CDM) constitutive model was used to represent the composite laminate. This 3D-CDM model was compared to a cohesive zone model (2D-CDM/CZM) to investigate efficacy of aluminum perforation energy prediction, delamination prediction, and computational cost. Accuracy of each model was evaluated using the experimental results. Each showed good agreement with the tests for both the force and velocity histories, as well as the observed damage mechanisms. The 2D-CDM/CZM model was marginally more accurate in capturing both the composite and aluminum behavior — this model averaged error percentages of -11.2% and 10.8% for residual velocity and peak force, respectively. Meanwhile, the 3D-CDM model predictions yielded average error percentages of -35.5% (velocity) and 22.6% (force). However, the 3D-CDM model generally resulted in a decreased computational cost; the average run time was 14% shorter than the 2D-CDM/CZM model and 3x as many timesteps per hour were computed using the same computational resources. In conclusion, new experimental data on the impact and perforation resistance of metal-composite laminates is presented in addition to numerical predictions of the impact behavior.

Carbon fiber↗
DOE OSTI2026

Conservative velocity mappings for discontinuous Galerkin kinetics

Continuum computational kinetic plasma models evolve the distribution function of a plasma species f s on a phase-space grid over time. In many problems of interest the distribution function has limited extent in velocity space; hence, using a uniform, highly refined mesh would be costly and slow. Nonuniform velocity grids can reduce the computational cost by placing more degrees of freedom where f s is appreciable and fewer where it is not. In this work we introduce a first-of-its kind discontinuous Galerkin approach to nonuniform velocity-space discretization using mapped velocity coordinates. This new method is presented in the context of a gyrokinetic model used to study magnetized plasmas. We create discretizations of collisionless and collisional terms using mappings in a way that exactly conserves particles and energy. Numerical tests of such properties are presented, and we show that this new discretization can reproduce earlier gyrokinetic simulations using grids with up to 6–60 times fewer cells and 22X-60X speed-ups depending on dimensionality, geometry and plasma parameters.

Discontinuous Galerkin↗
DOE OSTI2025

Multi-objective automatic discovery of optimized metamaterials for varying velocity impact protection

Mechanical metamaterials have demonstrated exceptional impact performance while remaining lightweight. Impact resistance has traditionally been investigated using quasi-static simulations, often with the assumption that performance will translate to high-velocity impact scenarios. However, critical crash protection parameters—such as peak stress and absorbed energy—are highly sensitive to impact velocity, leading to inconsistent performance under dynamic loading. To address this, we introduce a strain-rate-aware, active deep learning framework that enables multi-objective optimization of impact protection metrics across a wide range of impact velocities. Our framework captures the strain-rate sensitivity of architected lattices by learning to control spatial gradation in cellular metamaterials, resulting in over 200 % enhancement in impact protection relative to state-of-the-art designs such as Voronoi and re-entrant lattices. We demonstrate its practical utility by designing next-generation lattice structures for automotive bumper systems that satisfy multiple, velocity-specific safety criteria—capabilities beyond those of conventional designs. More than just a predictive tool, this framework marks the first step towards enabling adaptable impact-resistant structures across dynamic regimes.

Deep learning↗