Search NASA⌕ Search

SEARCH · Search NASA

Results for “VELOCITY, ANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1924

The Measurement of the Damping in Roll on a Jn4h in Flight

This investigation was carried out by the National Advisory Committee for Aeronautics for the purpose of measuring the value of L sub P in flight. The method consisted in flying with heavy weights on each wing tip, suddenly releasing one of them, and allowing the airplane to roll up to 90 degrees with controls held in neutral while a record was being taken of the airspeed, and angular velocity about the X axis. The results are of interest as they show that the damping found in the wind tunnel by the method of small oscillations is in general 40 per cent higher than the damping in flight. At 50 M. P. H. The flight curve of L sub P has a high peak, which is not indicated in the model results. It is also shown that at this speed the lateral maneuverability is low.

Norton, F H↗
NASA NTRS1924

The Effect of Airfoil Thickness and Plan Form on Lateral Control

This investigation was carried out for the purpose of determining the effectiveness of ailerons and tests were made on six model airfoils in the no. 1 wind tunnel of the National Advisory Committee for Aeronautics. The method consisted in measuring the rolling moments and aileron moments in the ordinary way. In addition to this the wing was allowed to spin freely about an axis in the direction of the air flow and the angular velocity measured. The results show that the thickness of the airfoil has very little effect on either the rolling moment or the hinge moment, although the resulting efficiency is somewhat higher for the tapered wings. The airfoil tapered in plan form, however, shows practically no falling off in the rolling moment at the critical angle of attack, whereas the wings of rectangular plan form show a marked dropping off in the rolling moment at this point. This indicates that it is possible to obtain good lateral control with small ailerons at low speed if the plan form is tapered. The rotational speed of the different airfoils is practically the same for all of the sections tested.

Hoot, H I↗
NASA NTRS1932

Maneuverability Investigation of the F6C-3 Airplane with Special Flight Instruments

This investigation was made for the purpose of obtaining information on the maneuverability of the F6C-3 airplane. It is the first of a series of similar investigations to be conducted on a number of military airplanes for the purpose of comparing the abilities of these airplanes to maneuver, and also to establish a fund of quantitative data which may be used in formulating standards of comparison for rating the maneuverability of any airplane. A large part of this initial investigation was necessarily devoted to the development and trial of methods suitable for use in subsequent investigations of this nature. Air speed, angular velocity, linear acceleration, and position of the control surfaces were measured by instruments in the airplane during loops, push-downs, pull-outs from dives, pull-ups from level flight, barrel rolls, and spins. The coordinates of flight paths were deduced from the data whenever possible, and were checked in some cases by the use of a camera obscura. The results are given in curves showing the variation of the measured quantities with respect to time, and maximum values are tabulated.

Dearborn, C H↗
NASA NTRS1934

Maneuverability Investigation of an O3U-1 Observation Airplane

This report presents the results of maneuverability tests of an O3U-1 observation airplane. This investigation is the third in a series of similar investigations requested by the Bureau of Aeronautics (Navy) for the purpose of comparing the maneuverability of different airplane types and to provide quantitative data for use in establishing a criterion or method for rating the maneuverability of an airplane. The two former investigations were conducted with the fighter types designated F6C-3 and F6C-4 and have been reported previously. Measurement of the air speed, the angular velocity, the linear acceleration, and positions of the controls were made during abrupt single-control maneuvers with three stop positions for each control, during steady horizontal turns for the determination of minimum radius, and during 180 degree turns by various methods. Flight-path coordinates in two dimensions were determined for the 180 degree turns by means of a special camera obscura designed for the previous investigation of the F6C-4 airplane. All maneuvers were performed at an altitude of approximately 3,000 feet.

Thompson, F L↗
NASA NTRS1937

Pressure-Distribution Measurements on O-2H Airplane in Flight

Results are given of pressure-distribution measurements made over two different horizontal tail surfaces and the right wing cellule, including the slipstream area, of an observation-type biplane. Measurements were also taken of air speed, control-surface positions, control-stick forces, angular velocities, and accelerations during various abrupt maneuvers. These maneuvers consisted of push-downs and pull-ups from level flight, dive pull-outs, and aileron rolls with various thrust conditions. The results from the pressure-distribution measurements over the wing cellule are given on charts showing the variation of individual rib coefficients with wing coefficients; the data from the tail-surface pressure-distribution measurements are given mainly as total loads and moments. These data are supplemented by time histories of the measured quantities and isometric views of the rib pressure distributions occurring in abrupt maneuvers.

Pearson, H A↗
NASA NTRS1954

A note on secondary flow in rotating radial channels

A general vector differential equation for the vorticity component parallel to a streamline is derived for steady, nonviscous, and incompressible flow in a rotating system. This equation is then simplified by restricting it to rotating radial channels and by making further simplifying assumptions. The simplified equation is used to solve for the secondary vorticity, the vorticity component parallel to the streamline, in three special cases involving different streamtube geometries; the results are presented in a series of figures. The secondary vorticity is shown to decrease with decreased absolute angular velocity of the fluid, decreased inlet total-pressure gradient, decreased length of relative flow path, and increased relative velocity.

Kramer, James J↗
NASA NTRS1957

The frequency content of the control input and airplane response obtained during service operations of fighter airplanes

The frequency content of the control input and resulting airplane motions is presented as power spectral densities for one operational flight of the fighter airplane (Republic F-84G). The frequency content, which is described by the shape of the spectrum, may be useful in providing inputs for the design of power control systems. For normal load factors, the results presented for the operational flight considered are in general agreement with the results of more complete data on three fighter airplanes (Republic F-84G, Republic F-84F, and North American F-86A) . The frequency content for the three control positions was similar and the frequency content for the three angular velocities was also similar when normalized by dividing the mean-square value.

Mayer, John P↗
NASA NTRS1955

Steady properly-banked turns of turbojet-propelled airplanes

The problem of a jet-propelled airplane held in a steady turn is treated both in the very general case and also in the particular case when the polar curve can be approximated by a parabola. Once the general solution has been obtained, some typical maneuvers are next studied such as, the turn of maximum bank, of maximum angular velocity, and of minimum radius of curvature. After a brief comparison is made between the turning characteristics of conventional airplanes and jet airplanes, and after the effect of compressibility upon the turn is examined, the effects of the salient aerodynamic and structural parameters upon the behavior of the plane in curvilinear flight are summarized in the conclusions.

AIRPLANES, JET↗
NASA NTRS1931

A study of curvilinear flight

When an airplane describes a curve it takes a certain time for it to turn from level to inclined position and then back to level again. In the following, we express the motion about the horizontal axis as "roll" or "bank" and the motion perpendicular to the vertical axis, i.e., the actual curve, as "turn." Equations and tables provide results on various aspects of turns, control settings, acceleration, inertia moments, and angular velocity.

Kruse, Helmuth↗
NASA NTRS1930

Contribution to the theory of propeller vibrations

This report presents a calculation of the torsional frequencies of revolving bars with allowance for the air forces. Calculation of the flexural or bonding frequencies of revolving straight or tapered bars in terms of the angular velocity of revolution. Calculation on the basis of Rayleigh's principle of variation. There is also a discussion of error estimation and the accuracy of results. The author then provides an application of the theory to screw propellers for airplanes and the discusses the liability of propellers to damage through vibrations due to lack of uniform loading.

Liebers, F↗
NASA NTRS1994

Sequential Design Of Rotation Control Of Flexible Structure

Improved procedure devised for designing and adjusting linear quadratic control system for somewhat flexible rotating structure like large radio antenna, large telescope, or robot arm. Basic purpose is making structure track desired rotation (for example, to rotate at specified rate to track celestial object or to slew to new observing direction) and suppressing vibrations, excited by wind or other external phenomena or by changes in angle and angular-velocity commands. Linear quadratic controllers for rotation tracking and suppressing vibrations designed separately.

Gawronski, Wodek↗
NASA NTRS1993

Flight testing and frequency domain analysis for rotorcraft handling qualities characteristics

A demonstration of frequency domain flight testing techniques and analyses was performed on a U.S. Army OH-58D helicopter in support of the OH-58D Airworthiness and Flight Characteristics Evaluation and the Army's development and ongoing review of Aeronautical Design Standard 33C, Handling Qualities Requirements for Military Rotorcraft. Hover and forward flight (60 knots) tests were conducted in 1 flight hour by Army experimental test pilots. Further processing of the hover data generated a complete database of velocity, angular rate, and acceleration frequency responses to control inputs. A joint effort was then undertaken by the Airworthiness Qualification Test Directorate (AQTD) and the U.S. Army Aeroflightdynamics Directorate (AFDD) to derive handling qualities information from the frequency response database. A significant amount of information could be extracted from the frequency domain database using a variety of approaches. This report documents numerous results that have been obtained from the simple frequency domain tests; in many areas, these results provide more insight into the aircraft dynamics that affect handling qualities than to traditional flight tests. The handling qualities results include ADS-33C bandwidth and phase delay calculations, vibration spectral determinations, transfer function models to examine single axis results, and a six degree of freedom fully coupled state space model. The ability of this model to accurately predict aircraft responses was verified using data from pulse inputs. This report also documents the frequency-sweep flight test technique and data analysis used to support the tests.

Ham, Johnnie A.↗
NASA NTRS1993

Physics of debris clouds from hypervelocity impacts

The protection scheme developed for long duration space platforms relies primarily upon placing thin metal plates or 'bumpers' around flight critical components. The effectiveness of this system is highly dependent upon its ability to break up and redistribute the momentum of any particle which might otherwise strike the outer surface of the spacecraft. Therefore it is of critical importance to design the bumpers such that maximum dispersion of momentum is achieved. This report is devoted to an in-depth study into the design and development of a laboratory instrument which would permit the in-situ monitoring of the momentum distribution as the impact event occurs. A series of four designs were developed, constructed and tested culminating with the working instrument which is currently in use. Each design was individually tested using the Space Environmental Effects Facility (SEEF) at the Marshall Space Flight Center in Huntsville, Alabama. Along with the development of the device, an experimental procedure was developed to assist in the investigation of various bumper materials and designs at the SEEF. Preliminary results were used to compute data which otherwise were not experimentally obtainable. These results were shown to be in relative agreement with previously obtained values derived through other methods. The results of this investigation indicated that momentum distribution could in fact be measured in-situ as the impact event occurred thus giving a more accurate determination of the effects of experimental parameters on the momentum spread. Data produced by the instrument indicated a Gaussian-type momentum distribution. A second apparatus was developed and it was placed before the shield in the line of travel utilized a plate to collect impact debris scattered backwards. This plate had a passage hole in the center to allow the particle to travel through it and impact the proposed shield material. Applying the law of conservation of angular momentum a backward momentum vector was determined from the angular velocity of the plate. The forward scattered and backward scattered momentum values were then analyzed to judge the distribution of debris. Loss of momentum was attributed to the inaccuracies of the means of measurement. Assumptions of symmetrical debris for the forward and backward scattered directions also contributed to this loss.

Zee, Ralph↗
NASA NTRS1994

Three-axis stabilization of spacecraft using parameter-independent nonlinear quaternion feedback

This paper considers the problem of rigid spacecraft. A nonlinear control law which uses the feedback of the unit quaternion and the measured angular velocities is proposed and is shown to provide global asymptotic stability. The control law does not require the knowledge of the system parameters, and is therefore robust to modeling errors. The significance of the control law is that it can be used for large-angle maneuvers with guaranteed stability.

Joshi, Suresh M.↗
NASA NTRS1991

Active localization of virtual sounds

We describe a virtual sound display built around a 12 MHz 80286 microcomputer and special purpose analog hardware. The display implements most of the primary cues for sound localization in the ear-level plane. Static information about direction is conveyed by interaural time differences and, for frequencies above 1800 Hz, by head sound shadow (interaural intensity differences) and pinna sound shadow. Static information about distance is conveyed by variation in sound pressure (first power law) for all frequencies, by additional attenuation in the higher frequencies (simulating atmospheric absorption), and by the proportion of direct to reverberant sound. When the user actively locomotes, the changing angular position of the source occasioned by head rotations provides further information about direction and the changing angular velocity produced by head translations (motion parallax) provides further information about distance. Judging both from informal observations by users and from objective data obtained in an experiment on homing to virtual and real sounds, we conclude that simple displays such as this are effective in creating the perception of external sounds to which subjects can home with accuracy and ease.

Loomis, Jack M.↗
NASA NTRS1994

Asteroseismology: Theory and phenomenology

Seismic studies of the Sun have succeeded in mapping the variation of sound speed with depth in the Sun, and variation of angular velocity with both depth and latitude. Many stars besides the Sun may also be amenable to asteroseismic analysis. Stars of roughly solar type should of course behave in ways similar to the sun, and stars of this sort form a large fraction of the potential targets for asteroseismology. But several other types of stars (delta scuti stars, roAP stars, and the pulsating white dwarfs) also have the desired pulsation characteristics. Pulsations in some of these stars are, for various reasons, much easier to observe than in the Sun-like stars. Virtually all unambiguous observations of multi-mode pulsators relate to these other categories of stars. Since oscillation mode frequencies are arguably the most precise measurement relating to a star that we can make, a few tens of such frequencies may still be of great importance to our understanding of the stellar structure and evolution.

Brown, Timothy M.↗
NASA NTRS1994

Anisotropic structure of homogeneous turbulence subjected to uniform rotation

Large-eddy simulation results are used to investigate the development of anisotropies and the possible transition towards a quasi two-dimensional state in rotating turbulence at high Reynolds number. The present study demonstrates the existence of two transitions that are identified by two Rossby numbers. The first transition marks the onset of anisotropic effects and corresponds to a macro Rossby number Ro(sup L) (based on a longitudinal integral length scale) near unity. A second transition can be defined in terms of a lower bound of micro-Rossby number Ro(sup w) also near unity (defined in this work as the ratio of the rms fluctuating vorticity to background vorticity) and corresponds to a continued development of anisotropy but with an increasing emergence of those indicators based on the pure two-dimensional component of the flow, e.g., integral length scales measured along the rotation axis. Investigation of the vorticity structure shows that the second transition is also characterized by an increasing tendency for alignment between the fluctuating vorticity vector and the basic angular velocity vector with a preference for corotative vorticity.

Cambon, C.↗
NASA NTRS1995

A NASTRAN-based computer program for structural dynamic analysis of Horizontal Axis Wind Turbines

This paper describes a computer program developed for structural dynamic analysis of horizontal axis wind turbines (HAWT's). It is based on the finite element method through its reliance on NASTRAN for the development of mass, stiffness, and damping matrices of the tower end rotor, which are treated in NASTRAN as separate structures. The tower is modeled in a stationary frame and the rotor in one rotating at a constant angular velocity. The two structures are subsequently joined together (external to NASTRAN) using a time-dependent transformation consistent with the hub configuration. Aerodynamic loads are computed with an established flow model based on strip theory. Aeroelastic effects are included by incorporating the local velocity and twisting deformation of the blade in the load computation. The turbulent nature of the wind, both in space and time, is modeled by adding in stochastic wind increments. The resulting equations of motion are solved in the time domain using the implicit Newmark-Beta integrator. Preliminary comparisons with data from the Boeing/NASA MOD2 HAWT indicate that the code is capable of accurately and efficiently predicting the response of HAWT's driven by turbulent winds.

Lobitz, Don W.↗