Results for “Vehicle modeling and simulation” — Page 22

NASA NTRS2011

Gain Scheduling for the Orion Launch Abort Vehicle Controller

One of NASAs challenges for the Orion vehicle is the control system design for the Launch Abort Vehicle (LAV), which is required to abort safely at any time during the atmospheric ascent portion of ight. The focus of this paper is the gain design and scheduling process for a controller that covers the wide range of vehicle configurations and flight conditions experienced during the full envelope of potential abort trajectories from the pad to exo-atmospheric flight. Several factors are taken into account in the automation process for tuning the gains including the abort effectors, the environmental changes and the autopilot modes. Gain scheduling is accomplished using a linear quadratic regulator (LQR) approach for the decoupled, simplified linear model throughout the operational envelope in time, altitude and Mach number. The derived gains are then implemented into the full linear model for controller requirement validation. Finally, the gains are tested and evaluated in a non-linear simulation using the vehicles ight software to ensure performance requirements are met. An overview of the LAV controller design and a description of the linear plant models are presented. Examples of the most significant challenges with the automation of the gain tuning process are then discussed. In conclusion, the paper will consider the lessons learned through out the process, especially in regards to automation, and examine the usefulness of the gain scheduling tool and process developed as applicable to non-Orion vehicles.

McNamara, Sara J.↗

NASA NTRS1995

Using the HARV simulation aerodynamic model to determine forebody strake aerodynamic coefficients from flight data

The method described in this report is intended to present an overview of a process developed to extract the forebody aerodynamic increments from flight tests. The process to determine the aerodynamic increments (rolling pitching, and yawing moments, Cl, Cm, Cn, respectively) for the forebody strake controllers added to the F/A - 18 High Alpha Research Vehicle (HARV) aircraft was developed to validate the forebody strake aerodynamic model used in simulation.

Messina, Michael D.↗

NASA NTRSDate not supplied

Unsteady CFD Simulations of a Compression Corner Geometry Using Wall-Modeled LES Methods in Loci/CHEM

As computing technology continues to improve, simulating unsteady aerodynamic environments on launch vehicle geometries becomes more viable. For NASA’s Space Launch System, the flowfield is characterized by large regions of unsteady turbulent wall-bounded flow. Simulating these unsteady wall-bounded environments is of interest to the SLS Aerodynamics team. Wall-modeled LES methods are currently the best approach for simulating these environments in engineering applications. Less-expensive computationally than fully-resolved methods while maintaining many of the benefits in simulating unsteady environments. Before applying these methods blindly to large geometries, best practices can first be applied and understood on smaller canonical problems.

Bryson Frank↗

NASA NTRS2002

Prediction of Aerodynamic Coefficient using Genetic Algorithm Optimized Neural Network for Sparse Data

Wind tunnels use scale models to characterize aerodynamic coefficients, Wind tunnel testing can be slow and costly due to high personnel overhead and intensive power utilization. Although manual curve fitting can be done, it is highly efficient to use a neural network to define the complex relationship between variables. Numerical simulation of complex vehicles on the wide range of conditions required for flight simulation requires static and dynamic data. Static data at low Mach numbers and angles of attack may be obtained with simpler Euler codes. Static data of stalled vehicles where zones of flow separation are usually present at higher angles of attack require Navier-Stokes simulations which are costly due to the large processing time required to attain convergence. Preliminary dynamic data may be obtained with simpler methods based on correlations and vortex methods; however, accurate prediction of the dynamic coefficients requires complex and costly numerical simulations. A reliable and fast method of predicting complex aerodynamic coefficients for flight simulation I'S presented using a neural network. The training data for the neural network are derived from numerical simulations and wind-tunnel experiments. The aerodynamic coefficients are modeled as functions of the flow characteristics and the control surfaces of the vehicle. The basic coefficients of lift, drag and pitching moment are expressed as functions of angles of attack and Mach number. The modeled and training aerodynamic coefficients show good agreement. This method shows excellent potential for rapid development of aerodynamic models for flight simulation. Genetic Algorithms (GA) are used to optimize a previously built Artificial Neural Network (ANN) that reliably predicts aerodynamic coefficients. Results indicate that the GA provided an efficient method of optimizing the ANN model to predict aerodynamic coefficients. The reliability of the ANN using the GA includes prediction of aerodynamic coefficients to an accuracy of 110% . In our problem, we would like to get an optimized neural network architecture and minimum data set. This has been accomplished within 500 training cycles of a neural network. After removing training pairs (outliers), the GA has produced much better results. The neural network constructed is a feed forward neural network with a back propagation learning mechanism. The main goal has been to free the network design process from constraints of human biases, and to discover better forms of neural network architectures. The automation of the network architecture search by genetic algorithms seems to have been the best way to achieve this goal.

Rajkumar, T.↗

NASA NTRS2008

Tests and Techniques for Characterizing and Modeling X-43A Electromechanical Actuators

A series of tests were conducted on the electromechanical actuators of the X-43A research vehicle in preparation for the Mach 7 and 10 hypersonic flights. The tests were required to help validate the actuator models in the simulation and acquire a better understanding of the installed system characteristics. Static and dynamic threshold, multichannel crosstalk, command-to-surface timing, free play, voltage regeneration, calibration, frequency response, compliance, hysteretic damping, and aircraft-in-the-loop tests were performed as part of this effort. This report describes the objectives, configurations, and methods for those tests, as well as the techniques used for developing second-order actuator models from the test results. When the first flight attempt failed because of actuator problems with the launch vehicle, further analysis and model enhancements were performed as part of the return-to-flight activities. High-fidelity models are described, along with the modifications that were required to match measurements taken from the research vehicle. Problems involving the implementation of these models into the X-43A simulation are also discussed. This report emphasizes lessons learned from the actuator testing, simulation modeling, and integration efforts for the X-43A hypersonic research vehicle.

Lin, Yohan↗

NASA NTRSDate not supplied

A Simulation Architecture for Air Traffic Over Urban Environments Supporting Autonomy Research in Advanced Air Mobility

As part of its research, NASA investigates concepts, aircraft, and operations related to Advanced Air Mobility (AAM). One of the most challenging scenarios for AAM will be enabling safe routine access near densely populated urban centers. AAM flight operations over a regional area require a moderately high-fidelity simulation capability to develop and evaluate autonomy technologies in the urban environment. This paper aims to describe a system to simulate flight operations around regions such as the San Francisco-Oakland Bay area at a moderately-high scale (tens to hundreds of flights) that incorporates detailed vehicle models and control necessary to support research in airborne autonomy. The flight vehicle utilizes NASA AAM concept vehicle dynamics integrated with a custom flight management system and flight control system to simulate all flight phases accurately. The simulation incorporates a detailed simulated urban environment and includes glass cockpit displays to monitor aircraft operations. Simulation models integrate to simulate air and ground-based sensors, such as Radar and LiDAR. As a commercially available rendering engine, X-Plane 11 is used as the renderer to simulate vision-based sensors (such as onboard and ground-based cameras) with a detailed graphical model of a city at different times of the day and weather conditions. This paper presents the simulation and software architecture used for simulating AAM traffic over this urban region. This system enables the evaluation of NASA research concepts in autonomy for urban AAM operations on the path toward flight test evaluation.

distributed sensing↗

NASA NTRSDate not supplied

A Simulation Architecture for Air Traffic Over Urban Environments Supporting Autonomy Research in Advanced Air Mobility

As part of its research, NASA investigates concepts, aircraft, and operations related to Advanced Air Mobility (AAM). One of the most challenging scenarios for AAM will be enabling safe routine access near densely populated urban centers. AAM flight operations over a regional area require a moderately high-fidelity simulation capability to develop and evaluate autonomy technologies in the urban environment. This paper aims to describe a system to simulate flight operations around regions such as the San Francisco-Oakland Bay area at a moderately-high scale (tens to hundreds of flights) that incorporates detailed vehicle models and control necessary to support research in airborne autonomy. The flight vehicle utilizes NASA AAM concept vehicle dynamics integrated with a custom flight management system and flight control system to simulate all flight phases accurately. The simulation incorporates a detailed simulated urban environment and includes glass cockpit displays to monitor aircraft operations. Simulation models integrate to simulate air and ground-based sensors, such as Radar and LiDAR. As a commercially available rendering engine, X-Plane 11 is used as the renderer to simulate vision-based sensors (such as onboard and ground-based cameras) with a detailed graphical model of a city at different times of the day and weather conditions. This paper presents the simulation and software architecture used for simulating AAM traffic over this urban region. This system enables the evaluation of NASA research concepts in autonomy for urban AAM operations on the path toward flight test evaluation.

Distributed sensing↗

NASA NTRSDate not supplied

Numerical Simulation of No-Vent Chill and Fill of a Large Liquid Hydrogen Tank

To enable the design of future in-space cryogenic propellant transfer vehicles, high accuracy models of the cryogenic propellant transfer process are desired. For in-space refueling applications, accurate simulations are desired of the propellant tank chilldown and no-vent fill (NVF) process in order to estimate the amount of propellant required, to determine the maximum sustainable flow rate to fill the tank, and to establish a timeline for the filling process. NVF is a complex process that involves numerous two-phase heat and mass transfer phenomena, such as boiling at the wall and evaporation and condensation at the liquid/vapor interface. In recent years, progress has been made in developing a numerical modeling technique using the Generalized Fluid System Simulation Program (GFSSP) that has been validated against several small-scale liquid nitrogen NVF tests. This paper presents GFSSP numerical model validation against three liquid hydrogen NVF tests on a large-scale propellant tank. Comparing the GFSSP model to the data for pressure, fill level, and wall temperature, the mean absolute percentage error is below 20% across the range of simulated conditions, indicating very good predictive agreement for this large-scale hydrogen NVF test series.

Alok Majumdar↗

NASA NTRSDate not supplied

Numerical Simulation of No-Vent Chill and Fill of a Large Liquid Hydrogen Tank

To enable the design of future in-space cryogenic propellant transfer vehicles, high accuracy models of the cryogenic propellant transfer process are desired. For in-space refueling applications, accurate simulations are desired of the propellant tank chilldown and no-vent fill (NVF) process in order to estimate the amount of propellant required, to determine the maximum sustainable flow rate to fill the tank, and to establish a timeline for the filling process. NVF is a complex process that involves numerous two-phase heat and mass transfer phenomena, such as boiling at the wall and evaporation and condensation at the liquid/vapor interface. In recent years, progress has been made in developing a numerical modeling technique using the Generalized Fluid System Simulation Program (GFSSP) that has been validated against several small-scale liquid nitrogen NVF tests. This paper presents GFSSP numerical model validation against three liquid hydrogen NVF tests on a large-scale propellant tank. Comparing the GFSSP model to the data for pressure, fill level, and wall temperature, the mean absolute percentage error is below 20% across the range of simulated conditions, indicating very good predictive agreement for this large-scale hydrogen NVF test series.

Alok Majumdar↗

NASA NTRS1975

Stochastic simulation of vertically nonhomogeneous gusts

The small-scale horizontal gust structure of detailed wind profiles along the vertical in the first 20 km of the atmosphere is a vertically nonhomogeneous process. A linear stochastic model was developed based on the process covariance function. This model was formulated through the use of a scaling hypothesis which transforms the nonhomogeneous gust process into a nondimensional gust process which is homogeneous in a nondimensional gust height coordinate. The velocity scaling parameter for the gust process is the gust standard deviation, and the length scale used to nondimensionalize the altitude is the vertical space lag associated with the first zero of the gust covariance function. State space theory was used to derive a digital filter from the model, which can be readily used to simulate gusts for space vehicle design applications.

Fichtl, G. H.↗

NASA NTRS1976

Stochastic simulation of vertically nonhomogeneous gusts

The small-scale horizontal gust structure of detailed wind profiles along the vertical in the first 20 km of the atmosphere is a vertically nonhomogeneous process. A linear stochastic model is developed for the process based on the process covariance function. This model is formulated through the use of a scaling hypothesis that transforms the nonhomogeneous gust process into a nondimensional gust process which is homogeneous in a nondimensional height coordinate. The velocity scaling parameter for the gust process is the gust standard deviation, and the length scale used to nondimensionalize the altitude is the vertical space lag associated with the first zero of the gust covariance function. State space theory is used to derive a digital filter from the model, which can be readily used to simulate gusts for space vehicle design applications.

Fichtl, G. H.↗

NASA NTRS1980

Space shuttle simulation model

The effects of atmospheric turbulence in both horizontal and near horizontal flight, during the return of the space shuttle, are important for determining design, control, and 'pilot-in-the-loop' effects. A nonrecursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gust gradients. Based on this model, the time series for both gusts and gust gradients were generated and stored on a series of magnetic tapes which are entitled shuttle simulation turbulence tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 10,000 meters. The turbulence generation procedure is described as well as the results of validating the simulated turbulence. Conclusions and recommendations are presented and references cited. The tabulated one dimensional von Karman spectra and the results of spectral and statistical analyses of the SSTT are contained in the appendix.

Tatom, F. B.↗

NASA NTRS1981

Advanced Shuttle Simulation Turbulence Tapes (SSTT) users guide

A nonrecursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity and also for simulation of instantaneous gust gradients. Based on this model, the time series for both gusts and gust gradients was generated and stored on a series of magnetic tapes which are entitled shuttle simulation turbulence tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 120,000 meters. An appropriate description of the characteristics of the simulated turbulence stored on the tapes, as well as instructions regarding their proper use are provided. The characteristics of the turbulence series, including the spectral shape, cutoff frequencies, and variation of turbulence parameters with altitude, are discussed. Information regarding the tapes and their use is presented. Appendices provide results of spectral and statistical analyses of the SSTT and examples of how the SSTT should be used.

Tatom, F. B.↗

NASA NTRS1982

Advanced Space Shuttle simulation model

A non-recursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed. It provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gusts gradients. Based on this model the time series for both gusts and gust gradients were generated and stored on a series of magnetic tapes, entitled Shuttle Simulation Turbulence Tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 120,000 meters. A description of the turbulence generation procedure is provided. The results of validating the simulated turbulence are described. Conclusions and recommendations are presented. One-dimensional von Karman spectra are tabulated, while a discussion of the minimum frequency simulated is provided. The results of spectral and statistical analyses of the SSTT are presented.

Tatom, F. B.↗

NASA NTRS1982

Advanced Space Shuttle simulation model

The effects of atmospheric turbulence in horizontal and near-horizontal flight during the return of the Space Shuttle are important for determining design, control, and pilot-in-the-loop effects. A nonrecursive model (based on vonKarman spectra) for atmospheric turbulence along the flight path of the Shuttle Orbiter has been developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity and also for simulation of instantaneous gust gradients. Based on this model the time series for gusts and gust gradients have been generated and stored on a series of magnetic tapes which are entitled Shuttle Simulation Turbulence Tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 120,000 meters. A description of the turbulence generation procedure is provided, the results of validating the simulated turbulence are described, and conclusions and recommendations are presented. Appendices provide tabulated one-dimensional vonKarman spectra, a discussion of the minimum frequency simulated, and the results of spectral and statistical analyses of the SSTT.

Tatom, F. B.↗

NASA NTRS1992

Thrust vectoring characteristics of the F-18 high alpha research vehicle at angles of attack from 0 to 70 deg

An investigation was conducted to determine the multiaxis thrust-vectoring characteristics of the F-18 High Alpha Research Vehicle (HARV). A 0.10-scale model was modified with hardware to simulate the three-vane thrust vectoring system of the F-18/HARV. This investigation was conducted at Mach numbers ranging from 0.30 to 0.70, at angles of attack from 0 to 70 deg, and nozzle-pressure ratios from 2.0 to approximately 5.0. Results indicate that the thrust vectoring system of F-18/HARV can successfully generate multiaxis thrust vectoring. During vectoring, resultant thrust-vector angles were always less than the corresponding geometric vane deflection angle and were accompanied by large thrust losses.

Asbury, Scott C.↗

NASA NTRS2000

NASA's Aero-Space Technology

This presentation reviews the three pillars and the associated goals of NASA's Aero-Space Technology Enterprise. The three pillars for success are: (1) Global Civil Aviation, (2) Revolutionary Technology Leaps, (3) Advanced Space Transportation. The associated goals of the first pillar are to reduce accidents, emissions, and cost, and to increase the aviation system capacity. The goals of the second pillar are to reduce transoceanic travel time, revolutionize general aviation aircraft, and improve development capacity. The goals associated with the third pillar are to reduce the launch cost for low earth orbit and to reduce travel time for planetary missions. In order to meet these goals NASA must provide next-generation design capability for new and or experimental craft which enable a balance between reducing components of the design cycle by up to 50% and or increasing the confidence in design by 50%. These next-generation design tools, concepts, and processes will revolutionize vehicle development. The presentation finally reviews the importance of modeling and simulation in achieving the goals.

Milstead, Phil↗

NASA NTRS2008

Building on 50 Years of Systems Engineering Experience for a New Era of Space Exploration

Over the past 50 years, the National Aeronautics and Space Administration (NASA) has delivered space transportation solutions for America's complex missions, ranging from scientific payloads that expand knowledge, such as the Hubble Space Telescope, to astronauts and lunar rovers destined for voyages to the Moon. Currently, the venerable Space Shuttle, which has been in service since 1981, provides the United States (US) capability for both crew and heavy cargo to low-Earth orbit to construct the International Space Station, before the Shuttle is retired in 2010. In the next decade, NASA will replace this system with a duo of launch vehicles: the Ares I crew launch vehicle and the Ares V cargo launch vehicle. The goals for this new system include increased safety and reliability coupled with lower operations costs that promote sustainable space exploration for decades to come. The Ares I will loft the Orion crew exploration vehicle, while the heavy-lift Ares V will carry the Altair lunar lander, as well as the equipment and supplies needed to construct a lunar outpost for a new generation of human and robotic space pioneers. NASA's Marshall Space Flight Center manages the Shuttle's propulsion elements and is managing the design and development of the Ares rockets, along with a host of other engineering assignments in the field of scientific space exploration. Specifically, the Marshall Center's Engineering Directorate houses the skilled workforce and unique facilities needed to build capable systems upon the foundation laid by the Mercury, Gemini, Apollo, and Shuttle programs. This paper will provide details of the in-house systems engineering and vehicle integration work now being performed for the Ares I and planned for the Ares V. It will give an overview of the Ares I system-level testing activities, such as the ground vibration testing that will be conducted in the Marshall Center's Dynamic Test Stand to verify the integrated vehicle stack's structural integrity and to validate computer modeling and simulation, as well as the main propulsion test article analysis to be conducted in the Static Test Stand. Ultimately, fielding a robust space transportation solution that will carry international explorers and essential payloads will pave the way for a new era of scientific discovery now dawning beyond planet Earth.

Dumbacher, Daniel L.↗