Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

PEROXIDE DESTRUCTION TESTING FOR THE 200 AREA EFFLUENT TREATMENT FACILITY

The hydrogen peroxide decomposer columns at the 200 Area Effluent Treatment Facility (ETF) have been taken out of service due to ongoing problems with particulate fines and poor destruction performance from the granular activated carbon (GAC) used in the columns. An alternative search was initiated and led to bench scale testing and then pilot scale testing. Based on the bench scale testing three manganese dioxide based catalysts were evaluated in the peroxide destruction pilot column installed at the 300 Area Treated Effluent Disposal Facility. The ten inch diameter, nine foot tall, clear polyvinyl chloride (PVC) column allowed for the same six foot catalyst bed depth as is in the existing ETF system. The flow rate to the column was controlled to evaluate the performance at the same superficial velocity (gpm/ft{sup 2}) as the full scale design flow and normal process flow. Each catalyst was evaluated on peroxide destruction performance and particulate fines capacity and carryover. Peroxide destruction was measured by hydrogen peroxide concentration analysis of samples taken before and after the column. The presence of fines in the column headspace and the discharge from carryover was generally assessed by visual observation. All three catalysts met the peroxide destruction criteria by achieving hydrogen peroxide discharge concentrations of less than 0.5 mg/L at the design flow with inlet peroxide concentrations greater than 100 mg/L. The Sud-Chemie T-2525 catalyst was markedly better in the minimization of fines and particle carryover. It is anticipated the T-2525 can be installed as a direct replacement for the GAC in the peroxide decomposer columns. Based on the results of the peroxide method development work the recommendation is to purchase the T-2525 catalyst and initially load one of the ETF decomposer columns for full scale testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DIRECT SIMULTANEOUS MEASUREMENT OF PARTICULATE MATTER AND AMMONIA STORAGE ON COMBINED SELECTIVE CATALYTIC REDUCTION FILTER SYSTEMS USING RADIO FREQUENCY SENSORS

Tightening global emissions regulations are motivating interest in the development and implementation of Selective Catalytic Reduction + Filtration (SCRF) systems, which are designed to reduce the concentration of tailpipe particulate matter (PM) and NO x emissions. These systems allow designers to combine the NO x reduction capability of an SCR with the filtration capability of a particulate filter on a single unit. Practical implementation of these systems requires reliable measurement and diagnosis of their state – both with respect to trapped particulate matter as well as adsorbed ammonia. Currently, these systems rely on a variety of gas sensors, mounted upstream or downstream of the system, that only provide an indirect inference of the operation state. In this study, a single radio frequency (RF) sensor was used to perform simultaneous measurements of soot loading and ammonia inventory on an SCRF. Several SCRF core samples were tested at varying soot and ash loads in a catalyst reactor bench. Soot levels were measured by monitoring changes in the bulk dielectric properties within the catalyst using the sensor, while ammonia levels were determined by feeding selected regions of the RF spectrum into a pretrained generalized regression neural network model. Results show the RF sensor is able to directly measure the instantaneous ammonia inventory, while simultaneously providing soot loading measurements within 0.5 g/L. These results confirm that simultaneous measurements of both the PM and ammonia loading state of an SCRF are possible using a single RF sensor via analysis of specific features in the full RF spectrum. The results indicate significant potential to remove the control barriers typically associated with the implementation of advanced SCRF systems.

Ragaller, Paul↗

Hydrogen production via reforming of biogas over nanostructured Ni/Y catalyst: Effect of ultrasound irradiation and Ni-content on catalyst properties and performance

Highlights: • Synthesis of nanostructured Ni/Y catalyst by sonochemical and impregnation methods. • Enhancement of size distribution and active phase dispersion by employing sonochemical method. • Evaluation of biogas reforming over Ni/Y catalyst with different Ni-loadings. • Preparation of highly active and stable catalyst with low Ni content for biogas reforming. • Getting H{sub 2}/CO very close to equilibrium ratio by employing sonochemical method. - Abstract: The effect of ultrasound irradiation and various Ni-loadings on dispersion of active phase over zeolite Y were evaluated in biogas reforming for hydrogen production. X-ray diffraction, field emission scanning electron microscopy, energy dispersive X-ray, Brunauer–Emmett–Teller, Fourier transform infrared analysis and TEM analysis were employed to observe the characteristics of nanostructured catalysts. The characterizations implied that utilization of ultrasound irradiation enhanced catalyst physicochemical properties including high dispersion of Ni on support, smallest particles size and high catalyst surface area. The reforming reactions were carried out at GHSV = 24 l/g.h, P = 1 atm, CH{sub 4}/CO{sub 2} = 1 and temperature range of 550–850 °C. Activity test displayed that ultrasound irradiated Ni(5 wt.%)/Y had the best performance and the activity remained stable during 600 min. Furthermore, the proposed reaction mechanism showed that there are three major reaction channels in biogas reforming.

36 MATERIALS SCIENCE↗

Ball Milling Modified SAPO‐11 Based Catalysts for n ‐Decane Hydroisomerization

Abstract Bifunctional Pt/SAPO‐11 catalysts were prepared using as acid matrix the microporous silico‐aluminophosphate, SAPO‐11, synthesized under microwave radiation. After synthesis, the material was physically modified using a ball mill, changing the grinding time but keeping frequency constant. The metal function (0.5 wt.% Pt) was introduced through mechanical mixture with commercial Pt loaded alumina. The catalysts were characterized by several techniques: powder X‐Ray Diffraction, pyridine adsorption followed by infrared spectroscopy, low temperature N 2 adsorption, Hg intrusion porosimetry and electronic microscopy (SEM). The characterization data show modifications of structural and textural properties of the samples as the milling time increases. The catalytic behaviour of Pt/SAPO‐11 materials was studied for hydroisomerization of long chain n ‐alkanes, using n ‐decane as model molecule, aiming to increase the production of mono‐branched isomers. The catalytic results show that, under optimized milling conditions (60 min; 50 Hz) the selectivity into mono‐branched isomers increased when compared with parent catalyst.

Ferreira, Luisa↗

Stepwise impregnation of bimetallic catalysts for carbon nanotube synthesis

Supported bimetallic catalysts are widely used for carbon nanotube (CNT) synthesis, yet the effects of impregnation procedure remain underexplored. Here, we investigated how the sequence of metal impregnation affects CNT synthesis. We prepared cobalt-molybdenum (Co-Mo) bimetallic catalysts on alumina supports via co- and stepwise impregnation, then compared their CNT synthesis performance under identical conditions. Stepwise-impregnated catalysts exhibited higher carbon yields than those prepared by co-impregnation. Notably, impregnating Mo after Co achieved the highest yield despite the lowest BET surface area. Synchrotron X-ray diffraction and visible/UV-Raman spectroscopy revealed that only this catalyst contained Al 2 (MoO 4 ) 3 with a MoO 4 structure. X-ray photoelectron spectroscopy clarified the surface chemistry: the catalyst with the highest CNT productivity exposed Mo entirely as Mo 6+ in Al 2 (MoO 4 ) 3 and CoMoO 4 , whereas the others contained both Mo 4+ and Mo 6+ . The MoO x species like Al 2 (MoO 4 ) 3 is known to suppress Co sintering during CNT synthesis, delaying catalyst deactivation and enhancing the carbon yield. Moreover, an inverse relationship was observed between carbon yield and the CoMoO 4 content. This is attributed to the consumption of catalytically active Co during CoMoO 4 formation, which reduces active sites for CNT growth. ICP-OES further confirmed higher Co and Mo loadings for stepwise catalysts, contributing to superior catalyst performance. The extent of CoMoO 4 formation strongly depended on the metal introduction sequence. In conclusion, this trend is illustrated by considering the relationship between the point of zero charge of support and the pH of the metal precursor solutions.

36 MATERIALS SCIENCE↗

Connecting cation site location to alkane dehydrogenation activity in Ni/BEA catalysts

Ni-modified beta zeolite (Ni/BEA) catalysts activate carbon-hydrogen bonds in light alkanes, as demonstrated through isobutane reaction testing. Controlled synthesis of Ni/BEA allows for efficient introduction of ion-exchanged Ni sites at varying Ni loadings (0.43% - 1.8%). These catalysts exhibit site time yields (STY) for H2 production that increase with increasing Ni loading. A detailed analysis of secondary reactions and carbon deposition based on the relative molar flowrates of product C and H indicates that the observed increase in H2 STY with increasing Ni loading is likely attributed to both increasing alkane activation activity and increasing formation of hydrogen-deficient aromatic products retained within the catalyst pores. In situ diffuse-reflectance UV-visible-NIR absorbance and X-ray absorption spectroscopies indicate isolated, 4-coordinate Ni(2+) species for all loadings. Quantum mechanics/molecular mechanics modeling identifies two distinct Ni(2+) sites consistent with the structural characterization, but with differing relative stabilities due to their coordination environment. Computed reaction energetics for isobutane dehydrogenation demonstrate that the more stable Ni(2+) species at a six-membered 4Si-2Al ring, Ni-6MR, is less active for isobutane dehydrogenation than the less stable Ni(2+) at the five-membered 3Si-2Al ring, Ni-5MR. The differing local structure of the isolated cationic Ni sites in Ni/BEA offers a possible rationalization for the increased H2 STY observed at greater Ni loadings.

catalysts↗

Synthesis, Characterization, and Catalytic Properties of Novel Single-Site and Nanosized Platinum Catalysts

Novel single-site platinum catalysts have been synthesized by reacting platinum(II) organometallics with partially dehydroxylated silica. The resulting materials have been characterized by various methods such as IR, MAS NMR, and EXAFS. Further, the single-site platinum catalysts were calcined in air to remove the ligand and produce nanosized platinum particles, that were characterized by TEM and H{sub 2} chemisorption. All catalysts were tested for the hydrogenation of toluene. The single-site platinum catalysts were less active than a commercial Pt/SiO{sub 2} catalyst with comparable platinum loading, and this has been ascribed to ligand effects. Conversely, the nanosized platinum catalysts were more active than the commercial Pt/SiO{sub 2} catalyst due to their high dispersion and small particle sizes.

36 MATERIALS SCIENCE↗

Enhanced Performance of Pt Nanoparticles on Ni-N Co-Doped Graphitized Carbon for Oxygen Reduction Reaction in Polymer Electrolyte Membrane Fuel Cells

Since the reaction rate and cost for cathodic catalyst in polymer electrolyte membrane fuel cells are obstacles for commercialization, the high-performance catalyst for oxygen reduction reaction is necessary. The Ni encapsulated with N-doped graphitic carbon (Ni@NGC) prepared with ethylenediamine and carbon black is employed as an efficient support for the oxygen reduction reaction. Characterizations show that the Ni@NGC has a large surface area and mesoporous structure that is suitable to the support for the Pt catalyst. The catalyst structure is identified and the size of Pt nanoparticles distributed in the narrow range of 2–3 nm. Four different nitrogen species are doped properly into graphitic carbon structure. The Pt/Ni@NGC shows higher performance than the commercial Pt/C catalyst in an acidic electrolyte. The mass activity of the Pt/Ni@NGC in fuel cell tests exhibits over 1.5 times higher than that of commercial Pt/C catalyst. The Pt/Ni@NGC catalyst at low Pt loading exhibits 47% higher maximum power density than the Pt/C catalyst under H2-air atmosphere. These results indicate that the Ni@NGC as a support is significantly beneficial to improving activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural and Chemical Evolution of an Inverse CeO x /Cu Catalyst under CO 2 Hydrogenation: Tunning Oxide Morphology to Improve Activity and Selectivity

Small nanoparticles of ceria deposited on a powder of CuO display a very high selectivity for the production of methanol via CO 2 hydrogenation. CeO 2 /CuO catalysts with ceria loadings of 5%, 20%, and 50% were investigated. Among these, the system with 5% CeO x showed the best catalytic performance at temperatures between 200 and 350 °C. The evolution of this system under reaction conditions was studied using a combination of environmental transmission electron microscopy (E-TEM), in situ X-ray absorption spectroscopy (XAS), and time-resolved X-ray diffraction (TR-XRD). For 5% CeO x /Cu, the in situ studies pointed to a full conversion of CuO into metallic copper, with a complete transformation of Ce 4+ into Ce 3+ . Images from E-TEM showed drastic changes in the morphology of the catalyst when it was exposed to H 2 , CO 2 , and CO 2 /H 2 mixtures. Under a CO 2 /H 2 feed, there was a redispersion of the ceria particles that was detected by E-TEM and in situ TR-XRD. Finally, these morphological changes were made possible by the inverse oxide/metal configuration and facilitate the binding and selective conversion of CO 2 to methanol.

03 NATURAL GAS↗

Chemical Vapor Deposition for Atomically Dispersed and Nitrogen Coordinated Single Metal Site Catalysts

Abstract Atomically dispersed and nitrogen coordinated single metal sites (M‐N‐C, M=Fe, Co, Ni, Mn) are the popular platinum group‐metal (PGM)‐free catalysts for many electrochemical reactions. Traditional wet‐chemistry catalyst synthesis often requires complex procedures with unsatisfied reproducibility and scalability. Here, we report a facile chemical vapor deposition (CVD) strategy to synthesize the promising M‐N‐C catalysts. The deposition of gaseous 2‐methylimidazole onto M‐doped ZnO substrates, followed by an in situ thermal activation, effectively generated single metal sites well dispersed into porous carbon. In particular, an optimal CVD‐derived Fe‐N‐C catalyst exclusively contains atomically dispersed FeN 4 sites with increased Fe loading relative to other catalysts from wet‐chemistry synthesis. The catalyst exhibited outstanding oxygen‐reduction activity in acidic electrolytes, which was further studied in proton‐exchange membrane fuel cells with encouraging performance.

Liu, Shengwen↗

Correlating Experimentally Determined Hydrogen Binding Energy with Hydrogen Evolution Activity over Metal Monolayers on Molybdenum Nitride

It is well established that hydrogen binding energy (HBE) is a key descriptor for hydrogen evolution reaction (HER) activity, and such a relationship is a useful tool for searching efficient and cost-effective HER catalysts. However, in almost all cases, the HBE values are obtained from density functional theory (DFT) calculations. Here in this study, temperature programmed desorption (TPD) was used to experimentally determine the HBE values of metal monolayers supported on molybdenum nitride (Mo 2 N), and electrochemical measurements were performed on the same surfaces. Combined DFT and kinetic Monte Carlo (kMC) simulations were used to validate the trend observed with TPD and the electrochemical HER activity. Depositing one monolayer of Pt on Mo 2 N led to similar HBE values seen for bulk Pt, and electrochemical measurements showed that monolayer Pt on Mo 2 N had similar HER activity to that of bulk Pt. Similar studies were also performed for monolayer Pd on Mo 2 N to confirm the correlation. This work also demonstrates that Mo 2 N is a promising support to reduce precious metal loading in HER catalysts.

08 HYDROGEN↗

Local Electric Field Effects on Water Dissociation in Bipolar Membranes Studied Using Core–Shell Catalysts

The local electric field strength is thought to affect the rate of water dissociation (WD) in bipolar membranes (BPMs) at the catalyst–nanoparticle surfaces. Here, we study core–shell nanoparticles, where the core is metallic, semiconducting, or insulating, to understand this effect. The nanoparticle cores were coated with a WD catalyst layer (TiO2 or HfO2) via atomic layer deposition (ALD), and the morphology was imaged with transmission electron microscopy. Irrespective of the core material, these core–shell catalysts displayed comparable WD overpotentials at optimal mass loading, despite the hypothesized differences in the electric field strength across the catalyst particle suggested by continuum electrostatic simulations. Substantial atomic interdiffusion between the core and shell was ruled out by X-ray absorption spectroscopy, X-ray photoelectron spectroscopy, and diffuse reflectance optical measurements. However, the optimal mass loading of catalyst was roughly 1 order of magnitude higher for the conductive and high dielectric core materials than for the low dielectric insulating cores. These findings are consistent with the hypothesis that electric field screening within the core material focuses the electric field drop between particles such that larger film thicknesses can be tolerated. Collectively, these data support the idea that it is the local electric field at the molecular level that controls proton-transfer rates and that the metal core/dielectric-shell constructs introduced here modulate that field. Further materials and synthetic design may enable optimization of the electric field strength across the proton-transfer trajectory at the material surface.

Sarma, Prasad V↗

Tuning core–shell interactions in tungsten carbide–Pt nanoparticles for the hydrogen evolution reaction

Platinum (Pt) is among the best electrocatalysts for the hydrogen evolution reaction (HER), a potentially fossil-free route for hydrogen production. Reduction in Pt loading and overall catalyst cost, without sacrificing catalytic activity, can be achieved by the synthesis of stable core–shell nanoparticles of transition-metal carbides and Pt. Here we employ density-functional theory (DFT) calculations to study and contrast the suitability of the α and β phases of tungsten carbide (WC) as support (core) materials for Pt shells. We examine the thermodynamic stability of 1–2 layers of Pt on α- and β-WC surfaces, carefully accounting for the delicate balance between epitaxial mismatch strains and chemical bonding between cores and shells. We also study the effects of alloying β-WC with Ti to modulate the stability and electronic structure of the core–shell structures. We compare the electronic structures of Pt overlayers supported on α-WC and β-Ti x W 1-x C surfaces and compare their activities for HER using the hydrogen binding energy as a descriptor of catalytic activity. Our studies reveal that moderate Ti doping of the metastable β-WC phase significantly improves its stability and, with merely two layers of Pt loading, HER activity comparable or superior to Pt(111) can be attained. Overall, our results provide detailed insight into experimental observations of the excellent stability and high catalytic activity of β-Ti x W 1-x C@Pt core–shell nanoparticles.

density functional theory↗

Dissecting the steps of CO2 reduction: 2. The interaction of CO and CO2 with Pd/γ-Al2O3: an in situ FTIR study

Alumina supported Pd catalysts with metal loadings of 0.5, 2.5 and 10 wt% were investigated by in situ FTIR spectroscopy in order to understand the nature of adsorbed species formed during their exposure to CO2 and CO. Exposing the annealed samples to CO2 at 295 K resulted in the formation of alumina support-bound surface species only: linear adsorbed CO2, bidentate carbonates and bicarbonates. Room temperature exposure of all three samples to CO produced IR features characteristic of both ionic and metallic Pd, as well as bands we observed upon CO2 adsorption (alumina support-bound species). Low temperature (100 K) adsorption of CO on the three samples provided information about the state of Pd after oxidation and reduction. Oxidized samples contained exclusively ionic Pd, while mostly metallic Pd was present in the reduced samples. Subsequent annealing of the CO-saturated samples revealed the facile (low temperature) reduction of PdOx species by adsorbed CO. This process was evidenced by the variations in IR bands characteristic of ionic and metallic Pd-bound CO, as well as by the appearance of IR bands associated with CO2 adsorption as a function of annealing temperature. Samples containing oxidized Pd species (oxidized, annealed or reduced) always produced CO2 upon their exposure to CO, while CO2-related surface entities were observed on samples having only fully reduced (metallic) Pd. Acknowledgements: The catalyst preparation was supported by a Laboratory Directed Research and Development (LDRD) project. This work was supported by the US Department of Energy Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy. JHK also acknowledges the support of this work by the 2013 Research Fund of UNIST (Ulsan National Institute of Science and Technology, Ulsan, Korea).

CO and CO2 adsorption↗

Solvent-Free Dimerization of Isoprene at Ambient Temperature: A Green Route to Biofuel-Range Hydrocarbons

In order to achieve a net-zero carbon footprint by 2050, the global aviation industry must reduce its dependence on fossil fuels. In this regard, there is a global challenge to produce sufficient sustainable aviation fuel (SAF) from renewable sources. Isoprene is an intermediate molecule that can be derived from multiple biomass-based or biosynthetic routes. Here, in this work, we report a green route for the catalytic conversion of isoprene to hydrocarbons that are suitable for aviation fuel. By using an Amberlyst-15 catalyst without metal loading at ambient temperature (19–23 °C), as well as 40 °C, 50 °C, and 60 °C, isoprene was converted into olefinic precursors for SAF and/or blending with conventional aviation fuels. Specifically, at ambient temperature, the process achieved approximately 70 wt % conversion of isoprene with over 50 mol % carbon selectivity toward the aviation fuel range. The resulting SAF-range hydrocarbons were composed of iso-alkenes, branched olefinic monocyclic compounds, and bicyclic compounds, covering a wide range of aviation fuel components. Our work demonstrates, for the first time, the formation of diverse hydrocarbon families for SAF and/or aviation fuel blending at ambient temperature from isoprene.

09 BIOMASS FUELS↗