Search NASA⌕ Search

SEARCH · Search NASA

Results for “conductive polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ionomer Optimization for Water Uptake and Swelling in Anion Exchange Membrane Electrolyzer: Oxygen Evolution Electrode

Water electrolysis using an anion conductive, solid polymer electrolyte is an attractive method for point-of-use hydrogen production. Recent advances in catalysts and anion exchange membranes (AEM) have made alkaline devices increasingly competitive with their acidic counterparts. However, less attention has been paid to the anion conductive ionomers (ACI) used in the fabrication of electrodes for AEM electrolyzers. The ACI contributes to ion conduction between the catalyst and bulk electrolyte and serves as a binder for adhering the catalyst to the gas diffusion layer and AEM. Ionic conductivity, water uptake and ionomer swelling are critical properties for electrode performance. High ion exchange capacity (IEC) in the ionomer is desired for reduced electrode resistance, however, it can lead to excess water uptake (WU) and disruptive ACI swelling. In this study, a series of poly(norbornene)-based ionomers were synthesized, characterized and used to fabricate oxygen evolving anodes for low-temperature AEM water electrolysis. The IEC of the ionomers (0 to 4.73 meq g −1 ) was adjusted by controlling the ratio of ion conducting to non-ion conducting norbornene monomers in the ACI tetrablock copolymers. Low conductivity ionomers are shown to yield the best-performing oxygen evolution electrodes, in the absence of ACI polymer cross-linking because they do not experience excessive water swelling. Light cross-linking within the anode ACI was used as a means to independently lower WU of the ionomer without compromising ionic conductivity. This control over water swelling allows higher ionic conductivity within the ACI to be used in water-fed electrolyzer applications. Other methods of water management were compared including the use of hydrophobic additives and adjustment of the ionomer concentration in the electrode. As a result, it was shown that the cell performance greatly benefits from a highly conductive ionomer in the oxygen evolution reaction electrode if the WU is managed.

08 HYDROGEN↗
NASA NTRS2013

Conductive Carbon Nanotube Inks for Use with Desktop Inkjet Printing Technology

Inkjet printing is a common commercial process. In addition to the familiar use in printing documents from computers, it is also used in some industrial applications. For example, wire manufacturers are required by law to print the wire type, gauge, and safety information on the exterior of each foot of manufactured wire, and this is typically done with inkjet or laser printers. The goal of this work was the creation of conductive inks that can be applied to a wire or flexible substrates via inkjet printing methods. The use of inkjet printing technology to print conductive inks has been in testing for several years. While researchers have been able to get the printing system to mechanically work, the application of conductive inks on substrates has not consistently produced adequate low resistances in the kilohm range. Conductive materials can be applied using a printer in single or multiple passes onto a substrate including textiles, polymer films, and paper. The conductive materials are composed of electrical conductors such as carbon nanotubes (including functionalized carbon nanotubes and metal-coated carbon nanotubes); graphene, a polycyclic aromatic hydrocarbon (e.g., pentacene and bisperipentacene); metal nanoparticles; inherently conductive polymers (ICP); and combinations thereof. Once the conductive materials are applied, the materials are dried and sintered to form adherent conductive materials on the substrate. For certain formulations, increased conductivity can be achieved by printing on substrates supported by low levels of magnetic field alignment. The adherent conductive materials can be used in applications such as damage detection, dust particle removal, smart coating systems, and flexible electronic circuitry. By applying alternating layers of different electrical conductors to form a layered composite material, a single homogeneous layer can be produced with improved electrical properties. It is believed that patterning alternate layers of different conductors may improve electrical pathways through alignment of the conductors and band gap optimization. One feature of this innovation is that flexible conductive traces could be accomplished with a conductive ink having a surface resistivity of less than 10 ohms/square. Another result was that a composite material comprising a mixture of carbon nanotubes and metallic nanoparticles could be applied by inkjet printing to flexible substrates, and the resulting applied material was one to two orders of magnitude more conductive than a material made by printing inks containing carbon nanotubes alone.

Roberson, Luke↗
NASA NTRS2007

Composite Electrolytes for Lithium Batteries: Ionic Liquids in APTES Crosslinked Polymers

Solvent free polymer electrolytes were made consisting of Li(+) and pyrrolidinium salts of trifluoromethanesulfonimide added to a series of hyperbranched poly(ethylene oxide)s (PEO). The polymers were connected by triazine linkages and crosslinked by a sol-gel process to provide mechanical strength. The connecting PEO groups were varied to help understand the effects of polymer structure on electrolyte conductivity in the presence of ionic liquids. Polymers were also made that contain poly(dimethylsiloxane) groups, which provide increased flexibility without interacting with lithium ions. When large amounts of ionic liquid are added, there is little dependence of conductivity on the polymer structure. However, when smaller amounts of ionic liquid are added, the inherent conductivity of the polymer becomes a factor. These electrolytes are more conductive than those made with high molecular weight PEO imbibed with ionic liquids at ambient temperatures, due to the amorphous nature of the polymer.

Tigelaar, Dean M.↗
NASA NTRS2006

Flexible Fabrics with High Thermal Conductivity for Advanced Spacesuits

This paper describes the effort and accomplishments for developing flexible fabrics with high thermal conductivity (FFHTC) for spacesuits to improve thermal performance, lower weight and reduce complexity. Commercial and additional space exploration applications that require substantial performance enhancements in removal and transport of heat away from equipment as well as from the human body can benefit from this technology. Improvements in thermal conductivity were achieved through the use of modified polymers containing thermally conductive additives. The objective of the FFHTC effort is to significantly improve the thermal conductivity of the liquid cooled ventilation garment by improving the thermal conductivity of the subcomponents (i.e., fabric and plastic tubes). This paper presents the initial system modeling studies, including a detailed liquid cooling garment model incorporated into the Wissler human thermal regulatory model, to quantify the necessary improvements in thermal conductivity and garment geometries needed to affect system performance. In addition, preliminary results of thermal conductivity improvements of the polymer components of the liquid cooled ventilation garment are presented. By improving thermal garment performance, major technology drivers will be addressed for lightweight, high thermal conductivity, flexible materials for spacesuits that are strategic technical challenges of the Exploration

Trevino, Luis A.↗
DOE OSTI2022

Reprocessable and Recyclable Polymer Network Electrolytes via Incorporation of Dynamic Covalent Bonds

Mechanically durable polymer network electrolytes are desirable for batteries; however, covalent cross-linking adversely affects their large-scale manufacturing, and they are difficult to recycle post-lifespan. In this work, we address the electrolyte reprocessability and recyclability challenges through the use of dynamic covalent bonds for polymer network solid electrolytes. Specifically, the associative dynamic vinylogous urethane motif is incorporated into a poly(ethylene oxide) network electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt. The resulting dynamic covalent network electrolyte possesses a modest ion conductivity (~10–5 S/cm at room temperature) and good reprocessability. Stress–relaxation studies indicate that the LiFSI salt can catalyze the bond exchange and enhance the network dynamics. Furthermore, the reprocessability associated with bond exchange can be tuned by simply adjusting the formulation of reagent compositions, in which increasing the amount of excess amine or using a shorter chain of PEO prepolymer can further enhance the network dynamics and corresponding reprocessability.

25 ENERGY STORAGE↗
DOE OSTI2023

Synthesis of hyperbranched polymer films via electrodeposition and oxygen-tolerant surface-initiated photoinduced polymerization

Hypothesis Hyperbranched polymers, not only possess higher functionality, but are also easier to prepare compared to dendrimers and dendric polymers. Combining electrodeposition and surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization is hypothesized to be a novel strategy for preparing hyperbranched polymer films on conductive surfaces without degassing. Experiments In this study, polymer brush grafted films with four different architectures (i.e. linear, branched, linear- block -branched, and branched- block -linear) were prepared on gold-coated glass substrates using electrodeposition, followed by SI-PET-RAFT polymerization. The resulting film structure and thickness, surface topology, absorption property, and electrochemical behavior were confirmed by spectroscopy, microscopy, microbalance technique, and impedance measurement. Findings These hyperbranched polymer brushes were capable of forming a thicker but more uniformly covered films compared to linear polymer brush films, demonstrating that hyperbranched polymer films can be potentially useful for fabricating protective polymer coatings on various conductive surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mastering the Copolymerization Behavior of Ethyl Cyanoacrylate as Gel Polymer Electrolyte for Lithium‐metal Battery Application

Polymers with strong electron-withdrawing groups (e.g., cyano-containing polymers) are attractive for a wide range of applications due to their high dielectric constant and outstanding electrochemical stability. However, the polymerization of such monomers is difficult to control with trace of water affording instant reactions, and copolymerization with other monomers without using strong acid is even more challenging. The present study demonstrates a facile approach enabling efficient and controllable copolymerization of ethyl cyanoacrylate (ECA) without adding undesired additives, achieving mechanically robust and high ion-conduction gel polymer electrolyte (GPE) for safe and long cycle-life lithium-metal batteries (LMBs). The incorporated dual-lithium salts, i.e., lithium difluoro(oxalato)borate (LiDFOB) and lithium bis(trifluoromethanesulphonyl)imide (LiTFSI) not only facilitate radical polymerization of ECA monomers by suppressing their anionic polymerization, but also promote the formation of high-ionic conducting GPE. The incorporated methyl methacrylate (MMA) monomer accelerates the radical polymerization of ECA (confirmed by DFT calculations), achieving controlled copolymerization of ECA-based copolymers. Here, the mechanically robust polymer network made by the ECA copolymer enables LMBs with both LFP cathodes and high-voltage LCO cathodes (4.5 V) operatable at different temperatures with ultra-long cycle life at 1 C (capacity retention of 81.1 % and 83.8 %, respectively, over 1000 cycles).

Min, Weixing [Nankai University, Tianjin (China)]↗
DOE OSTI2020

First Ever Polymer Flood Field Pilot to Enhance the Recovery of Heavy Oils on Alaska North Slope – Producer Responses and Operational Lessons Learned

The US Department of Energy and Hilcorp Alaska, LLC are jointly cosponsoring a field pilot project entitled “First Ever Field Pilot on Alaska’s North Slope to Validate the Use of Polymer Floods for Heavy Oil Enhanced Oil Recovery (EOR).” The objective of this pilot is to perform a field experiment to validate the use of an advanced polymer flooding technology to unlock the vast heavy oil resources on Alaska North Slope (ANS). Two pairs of horizontal injection and production wells have been deployed in an isolated fault block of the Schrader Bluff heavy oil reservoir at the Milne Point Field to conduct a polymer flood pilot which was designed to acquire field performance data to optimize polymer flood design in the Schrader Bluff heavy oil reservoirs on ANS. Hydrolyzed polyacrylamide (HPAM) polymer injection started on August 28, 2018 using a custom made polymer mixing and pumping unit. Polymer solution properties such as concentration, viscosity, and filter ratio, have been closely monitored and adjusted as necessary. Operational procedures have been improved to ensure adequate injectivity and polymer propagation through the formation. Oil and water production is tested frequently to monitor water cut performance, and produced water is sampled and analyzed for polymer content. Tracers were pumped pre and post polymer injection startup to compare polymer flood breakthrough timing and sweep efficiency. Polymer injectivity of the horizontal wells drilled in the Schrader Bluff NB sand is found to be sufficient to replace the reservoir production voidage although there were some declines as high viscosity polymer swept the near wellbore region. Production data show significant reduction in water cut and the oil production rate has stabilized. No polymer production has been confirmed from the two horizontal producers after 22 months of polymer injection into the two supporting horizontal injectors. Tracer data show very low sweep efficiencies with waterflood alone, whereas significant improvement has been achieved with polymer flood. Many operational lessons have been learned and improvements have been made regarding polymer mixing, pumping, and onsite quality control, particularly in a challenging Arctic environment. Adequate polymer injection rate can be achieved with diligent monitoring and quality assurance of the properties of the injected polymer solution.

Ning, Samson↗
DOE OSTI2025

Harnessing ionic complexity: A modeling approach for hierarchical ionic circuit design

Since the 1950s, soft ionic devices have evolved from individual components to an expanding library of sensors, actuators, signal transmitters, and processors. However, integrating these components into complex, multifunctional systems remains challenging due to the nonintuitive and nonlinear interactions between ionic elements. In this work, we address these fundamental challenges by developing a lumped element model that enables interrogation of the physics that governs ionic circuits, as well as rapid design and optimization. Our model captures features specific to ionic charge carriers, while preserving the hierarchical design flexibility and computational efficiency of traditional circuit modeling. We demonstrate that our model can not only fit individual device behavior but also accurately predict the behavior of larger circuits formed by combining those devices. Additionally, we show how our tool utilizes the intrinsic nonlinearities of ionic systems to enable extended functionality, revealing how factors such as ion enrichment, ion leakage, and polymer charge density influence performance. Lastly, we present a fully ionic power supply, sensor, control system, and actuator for a soft robot that adapts its motion in response to environmental salt, illustrating the tool’s potential to accelerate advancements in chemical sensing, biointerfacing, biomimetic systems, and adaptive materials.

42 ENGINEERING↗
DOE OSTI2026

Mechanistic insight into the effects of A-site doping in perovskite nanorods on interfacial Li-ion and Na-ion transport in polymer–perovskite composite electrolytes

Composite polymer electrolytes (CPEs) offer a promising pathway to safer and higher energy density electrochemical energy storage yet optimizing interfacial ion transport remains a critical challenge due to high resistances and a lack of understanding of the complex interfacial electrostatic interactions. This work investigates the mechanistic origins of the interfacial ion transport enhancement in single-ion conducting (SIC) polymer electrolytes filled with A-site disordered perovskite LaxMyTiOz (LMTO) (M = Li, Na, K) nanorods. By integrating Density Functional Theory (DFT) with broadband dielectric spectroscopy (BDS) and pulsed-field-gradient NMR (PFG-NMR), we analyze the ion transport behavior in Li-based and Na-based SIC systems containing compositionally distinct LMTO fillers (LMTO800 and LMTO900). Specifically, we introduce the site-to-site energy difference (ΔE) descriptor, which extends beyond single-site descriptors such as adsorption energy and ion binding energies. We demonstrate that ΔE together with ion binding energies provide a more comprehensive picture of the energy landscape at the polymer–ceramic interface. The combined DFT and experimental results show that A-site doping in the ceramic filler can effectively modulate ΔE and ion binding energies, creating a favorable potential energy landscape that promotes enhanced ion transport along the interface. This comprehensive study illustrates the impact of ceramic compositional tuning on interfacial ion transport and provides materials design rules towards real-world applications.

B shepard, Lauren [Pennsylvania State University]↗
DOE OSTI2020

Enhanced Surface Interactions Enable Fast Li + Conduction in Oxide/Polymer Composite Electrolyte

Abstract Li + ‐conducting oxides are considered better ceramic fillers than Li + ‐insulating oxides for improving Li + conductivity in composite polymer electrolytes owing to their ability to conduct Li + through the ceramic oxide as well as across the oxide/polymer interface. Here we use two Li + ‐insulating oxides (fluorite Gd 0.1 Ce 0.9 O 1.95 and perovskite La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 2.55 ) with a high concentration of oxygen vacancies to demonstrate two oxide/poly(ethylene oxide) (PEO)‐based polymer composite electrolytes, each with a Li + conductivity above 10 −4 S cm −1 at 30 °C. Li solid‐state NMR results show an increase in Li + ions (>10 %) occupying the more mobile A2 environment in the composite electrolytes. This increase in A2‐site occupancy originates from the strong interaction between the O 2− of Li‐salt anion and the surface oxygen vacancies of each oxide and contributes to the more facile Li + transport. All‐solid‐state Li‐metal cells with these composite electrolytes demonstrate a small interfacial resistance with good cycling performance at 35 °C.

Wu, Nan↗
DOE OSTI2021

Wafer-scale quasi-layered tungstate-doped polypyrrole film with high volumetric capacitance

Layered materials are particularly attractive for supercapacitors because of their unique physical, electrical and chemical properties. In this work, we demonstrate a facile and scalable electrochemical deposition method for wafer-scale synthesis of quasi-layered tungstate-doped polypyrrole films (named TALPy) with controllable thickness and size. The as-prepared TALPy film exhibits a high gravimetric density and excellent volumetric capacitance, exceeding many high-performing carbon- and polymer-based film electrodes. Based on combined results of ex-situ X-ray diffraction (XRD), Raman and X-ray photoelectron spectroscopy (XPS), it is determined that TALPy stores charge through an ion intercalation process accompanied by change in oxidation states of polypyrrole backbone, which is referred as intercalation pseudocapacitance. All these results suggest the great promise of electrochemical deposition as a scalable and controllable bottom-up approach for synthesizing quasi-layered conductive organic-inorganic hybrid films for electrochemical energy storage applications with high volumetric performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding the Structure and Dynamics of Conjugated Polymers by Advancing Deuteration Chemistry and Neutron Scattering (Final Report)

The overarching goal of the proposed work was to set up a partnership between the University of Southern Mississippi (USM) and Oak Ridge National Laboratory (ORNL) to develop novel approaches to measure the backbone rigidity of conjugated polymers (CPs) and understand the critical role of sidechains on the backbone conformation and the materials macroscopic property. The backbone rigidity greatly influences the electronic properties of CPs, which ultimately determines the functionality and performance of these materials. Improvements in the electronic properties of CPs would allow for enhanced charge transport in semiconductor devices, improved photovoltaic performance, recycling of waste heat in thermoelectrics, and discovery of new phenomena that will enable the next generation of energy technologies. Although significant progress has been made to optimize the optical and electronic properties of CPs, largely through Edisonian methodologies, it remains a challenge to experimentally characterize conjugated backbone conformation (chain rigidity, torsion, planarity, and short-range order) and relate these to the fundamental optical and electronic properties (electronic coupling, charge transport, etc.). This has left fundamental gaps in our knowledge of the most basic structure/property relationships within these systems, precluded the study of fundamental physical phenomena, and constrained the design and realization of new electronic and device functionalities. Thus, the major goal of this work is to use novel deuteration methodologies via systematic synthetic approaches, and neutron scattering techniques to comprehensively characterize the structural and dynamic properties of CPs in contrast-matching solvents. Our work would, for the first time, elucidate the relationship between backbone rigidity and macroscopic properties. They will also allow a rational formulation of design principles for next-generation CPs that are resilient to disorder through precise control of the delocalized electrons along the polymer backbone. Overall, this project will advance our understanding of the structure, dynamics, and fundamental physics of these materials, which is crucial for enabling the prediction, design, control, and manipulation of current and emerging material electronic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

HydroGEN Consortium

HydroGEN Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and thermochemical (TCH) water splitting. The AWS technologies in this consortium study proton conduction in solid oxide electrolysis and hydroxide conduction in polymer electrolysis, and proton transport in photoelectrochemical water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and DOE-awarded "seedling" R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

08 HYDROGEN↗
DOE OSTI2026

HydroGEN Consortium: Advancements in Hydrogen Production

HydroGEN Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and thermochemical (TCH) water splitting. The AWS technologies in this consortium study proton conduction in solid oxide electrolysis and hydroxide conduction in polymer electrolysis, and proton transport in photoelectrochemical water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and DOE-awarded "seedling" R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

08 HYDROGEN↗
DOE OSTI2021

Dynamics of a single polyampholyte chain

Polymers that feature both positive and negative charges along chains, known as polyampholytes, represent a class of materials that hold promise for a new generation of energy storage devices, the design of which will require knowledge of the underlying structure and dynamics. Here, we develop a theory based on the Rouse model for the dynamic structure factor of a single polyampholyte chain in the weak coupling regime (negligible intramolecular electrostatics) or subjected to weak external electric fields (governed by linear response). Neglecting effects of small ions, we find deviations in scaling from the classic Rouse theory and make predictions for scattering experiments performed on polyampholytes. We find that, under weak coupling with arbitrarily strong fields, the dynamics are highly dependent on the charge distribution and consequently look at two representative examples—random charge densities and periodic charge densities—with different scaling properties. Additionally, under weak fields, the dynamics are largely independent of charge distribution. Finally, we investigate the influence of hydrodynamic effects and the implications of including inertial effects in the model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗