Search NASA⌕ Search

SEARCH · Search NASA

Results for “deformation function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Orientation dependent spall strength of tantalum single crystals

We report that it is generally recognized that single crystals exhibit orientation-dependent elastic and plastic responses. However, it is less known how the dynamic tensile, or spall, strength depends on crystalline orientation, especially for BCC materials. It has been previously shown that the dynamic tensile strength of FCC materials is highly dependent on their plastic response under compression, with a direct correlation between plastic deformation and spall strength. In BCC materials like Ta, where the primary deformation mechanism at high strain rates is a combination of slip and twinning, the quantitative dependence of spall strength on these deformation mechanisms is less understood. To fill this gap in our knowledge, a series of non-equilibrium molecular dynamics simulations are completed for six tantalum single crystal orientations: <001>, <011>, <111>, <013>, <112>, <149>, to explore the role of directional anisotropy on ductile spallation. Our results show that due to the role of non-Schmid and release effects in BCC Ta, the evolution of plasticity follows a complex trajectory through shock compression, release, and tension. Orientations that contain residual twinning deformation have a reduced spall strength proportional to the amount of twinning present. Lastly, twins and their intersections function as regions of increased stress localization within the system due to compatibility requirements and their interactions with dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pomeranchuk instability from electronic correlations in CsTi 3 Bi 5 kagome metal

Electronic nematicity, the spontaneous breaking of rotational symmetry, has emerged as a key instability in correlated quantum systems. CsTi 3 Bi 5 , a kagome metal of the AV 3 Sb 5 (A = K, Rb, Cs) family, hosts rich unconventional electronic phases, yet the origin of its nematicity remains unsettled. Here, we combine polarization-dependent angle-resolved photoemission spectroscopy with functional renormalization group calculations on a fully interacting ab initio model. We reveal an orbital-selective nematic deformation in the low-energy band structure and identify a finite angular momentum (d-wave) Pomeranchuk instability driven by electronic correlations in specific orbital channels and detuning from Van Hove singularities. Our results establish a direct link between orbital selectivity and symmetry-breaking instabilities in CsTi 3 Bi 5 , providing a microscopic framework for nematic order in kagome systems.

Bigi, Chiara [Synchrotron SOLEIL, Saint-Aubin (Fra↗
DOE OSTI2024

A new method for solving the linearized 1D Vlasov–Poisson system yielding a new class of solutions

We describe a new method for solving the linearized 1D Vlasov–Poisson system by using properties of Cauchy-type integrals. Our method remedies critical flaws of the two standard methods, reveals a previously unrecognized Gaussian-in-time-like decay, and can also account for an externally applied electric field. The Landau approximation involves deforming the Bromwich contour around the poles closest to the real axis due to the analytically continued dielectric function, finding the long-time behavior for a stable system: Landau damping. Jackson's generalization encircles all poles while sending the contour to infinity, assuming its contribution vanishes, which is not true in general. This gives incorrect solutions for physically reasonable configurations and can exhibit pathological behavior, of which we show examples. The van Kampen method expresses the solution for a stable equilibrium as a continuous superposition of waves, resulting in an opaque integral. Case's generalization includes unstable systems and predicts a decaying discrete mode for each growing discrete mode, an apparent contradiction to both the Jackson solution and ours. We show, without imposing additional constraints, that the decaying modes are never present in the time evolution due to an exact cancellation with part of the continuum. Our solution is free of integral expressions, is obtained using algebra and Laurent series expansions, does not rely on analytic continuations, and results in a correct asymptotically convergent form in the case of infinite sums. The analysis used can be readily applied in higher-dimensional, electromagnetic systems and also provides a new technique for evaluating certain inverse Laplace transforms.

Physics↗
DOE OSTI2024

Regulating loops in de Sitter spacetime

Perturbative quantum field theory (QFT) calculations in de Sitter space are riddled with contributions that diverge over time. These contributions often arise from loop integrals, which are notoriously hard to compute in de Sitter. We discuss an approach to evaluate loop integrals that contribute to equal-time correlators of a scalar field theory in a fixed de Sitter background. Our method is based on the Mellin-Barnes representation of correlation functions, which allows us to regulate loop divergences by adjusting the masses of the fields, or by gently deforming the underlying de Sitter spacetime. The resulting expressions have a similar structure as a standard answer from dimensional regularization in flat space QFT. These features of the regulator are illustrated with two examples, worked out in detail. Along the way, we illuminate the physical origin of these divergences and their interpretation with the machinery of the dynamical renormalization group. Our approach regulates the IR divergences of massless and massive particles in the same way. For massless scalars, the loop corrections can be incorporated as systematic improvements to the stochastic inflation framework, allowing for a more precise description of the IR dynamics of such fields in de Sitter. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
DOE OSTI2020

In situ measurement and modelling of the growth and length scale of twins in α -uranium

Twinning is an important deformation mechanism in crystalline materials. Twins nucleate, then grow, forming a discrete pattern of deformation bands with a certain thickness. The mechanism for twin growth is not completely understood. We present a simple phase field model which captures the physics of twin growth and reproduces the details observed during in situ electron backscatter diffraction experiments on α-uranium. The interaction between residual dislocations at twin interfaces and mobile dislocations in untwinned regions increases the stress needed for twin growth. This is described by a nonlocal term in the proposed constitutive equations: the nucleation stress of a twin increases proportionally to the twin phase field in a neighborhood. Competition between slip and twinning favors the nucleation of a new twin rather than the growth of a preexisting twin. The phase field model is coupled with a crystal plasticity finite element solver that includes the plastic deformation due to twinning. Simulations are able to reproduce the number of twins and their thicknesses as a function of the strain observed during in situ electron backscatter diffraction experiments. The stress-strain curve is also reproduced. This comparison allows the values of the nucleation stress and the interaction strength between residual and mobile dislocations to be found. It also gives an estimation of the density of residual dislocations that is consistent with the observed twin thickness. Finally, this model can be applied to understand microstructural effects in materials using twinning as a strengthening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimization of microwave emission from laser filamentation with a machine learning algorithm

We demonstrate that is it possible to optimize the yield of microwave radiation from plasmas generated by laser filamentation in atmosphere through manipulation of the laser wavefront. A genetic algorithm controls a deformable mirror that reconfigures the wavefront using the microwave waveform amplitude as feedback. Optimization runs performed as a function of air pressure show that the genetic algorithm can double the microwave field strength relative to when the mirror surface is flat. Here, an increase in the volume and brightness of the plasma fluorescence accompanies the increase in microwave radiation, implying an improvement in the laser beam intensity profile through the filamentation region due to the optimized wavefront.

Englesbe, Alexander↗
DOE OSTI2017

2016 Accomplishments. Tritium aging studies on stainless steel. Forging process effects on the fracture toughness properties of tritium-precharged stainless steel

Forged austenitic stainless steels are used as the materials of construction for pressure vessels designed to contain tritium at high pressure. These steels are highly resistant to tritium-assisted fracture but their resistance can depend on the details of the forging microstructure. During FY16, the effects of forging strain rate and deformation temperature on the fracture toughness properties of tritium-exposed-and-aged Type 304L stainless steel were studied. Forgings were produced from a single heat of steel using four types of production forging equipment – hydraulic press, mechanical press, screw press, and high-energy-rate forging (HERF). Each machine imparted a different nominal strain rate during the deformation. The objective of the study was to characterize the J-Integral fracture toughness properties as a function of the industrial strain rate and temperature. The second objective was to measure the effects of tritium and decay helium on toughness. Tritium and decay helium effects were measured by thermally precharging the as-forged specimens with tritium gas at 34.5 MPa and 350°C and aging for up to five years at -80°C to build-in decay helium prior to testing. The results of this study show that the fracture toughness properties of the as-forged steels vary with forging strain rate and forging temperature. The effect is largely due to yield strength as the higher-strength forgings had the lower toughness values. For non-charged specimens, fracture toughness properties were improved by forging at 871°C versus 816°C and Screw-Press forgings tended to have lower fracture toughness values than the other forgings. Tritium exposures reduced the fracture toughness values remarkably to fracture toughness values averaging 10-20% of as-forged values. However, forging strain rate and temperature had little or no effect on the fracture toughness after tritium precharging and aging. The result was confirmed by fractography which indicated that fracture modes in the tritium-exposed specimens were similar for all forgings. Another FY16 objective was to prepare fracture toughness specimens from Types 304L and 21-6-9 stainless steel weldments and heat-affected zones (HAZ) for tritium charging.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sound Speed as a Candidate for Internal Temperature Monitoring During Solid Phase Processing of Materials

Internal temperature is an important parameter for understanding the solid phase processing (SPP) of materials and improving feedback control of these processes. Friction stir processes, shear assisted processing and extrusion (ShAPE ™ ), and ultrahigh velocity (UHV) cold spray are examples of such processes. Simple thermal models based on temperatures measured at the boundary of the deforming body cannot capture the dynamic nature of temperature generation within the deforming solid. One possibly way of understanding internal temperature is by measuring sound speed, which varies as a function of temperature for materials and directing ultrasonic wave propagation through selected material volumes of interest. In this project, longitudinal wave speed is estimated for aluminum 6061. Piezoelectric materials bonded to a specimen provided data from which longitudinal wave speed was estimated. A discussion evaluated the linear relationship of wave speed versus temperature and postulated how wave speed measurements could be used to estimate the internal temperature of selected material volumes for feedback during SPP of materials. Instrumentation, data and analysis, and a discussion are reviewed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Influence of Temperature on the Electromechanical Properties of Ionic Liquid-Doped Ionic Polymer-Metal Composite Actuators

Ionic polymer-metal composite (IPMC) actuators have considerable potential for a wide range of applications. Although IPMC actuators are widely studied for their electromechanical properties, most studies have been conducted at the ambient conditions. The electromechanical performance of IPMC actuators at higher temperature is still far from understood. In this study, the effect of temperature on the electromechanical behavior (the rate of deformation and curvature) and electrochemical behavior (current flow) of ionic liquid doped IPMC actuators are examined and reported. Both electromechanical and electrochemical studies were conducted in air at temperatures ranging from 25 °C to 90 °C. Electromechanically, the actuators showed lower cationic curvature with increasing temperature up to 70 °C and a slower rate of deformation with increasing temperature up to 50 °C. A faster rate of deformation was recorded at temperatures higher than 50 °C, with a maximum rate at 60 °C. The anionic response showed a lower rate of deformation and a higher anionic curvature with increasing temperatures up to 50 °C with an abrupt increase in the rate of deformation and decrease of curvature at 60 °C. In both cationic and anionic responses, actuators started to lose functionality and show unpredictable performance for temperatures greater than 60 °C, with considerable fluctuations at 70 °C. Electrochemically, the current flow across the actuators was increased gradually with increasing temperature up to 80 °C during the charging and discharging cycles. A sudden increase in current flow was recorded at 90 °C indicating a shorted circuit and actuator failure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Naturally Self-Tuned Low Mass Composite Scalars

Scalar bosons composed of a pair of chiral fermions in a non-confining potential have an effective Yukawa coupling, $g$, to free external chiral fermions. At large distance a Feynman loop of external fermions generates a scale invariant potential, $V_{loop}\propto -g^2/{\rho^{2}}$, for separation $\rho$, which acts on valence fermions. This generally forces the $s$-wave ground state to deform to a static, zero mass, configuration, and for slowly running, perturbative $g$, a large external "shroud" wave function forms. This is related to old results of Landau and Lifshitz in quantum mechanics. The massless composite scalar boson ground state is then an extended object. Infra-red effects can generate a small mass for the system. This points to a perturbative BEH-boson composed of top and anti-top quarks and a novel dynamical mechanism for spontaneous electroweak symmetry breaking.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2018

Atomic and Molecular Adsorption on Cu(111)

Here, due to the wide use of copper-based catalysts in industrial chemical processes, fundamental understanding of the interactions between copper surfaces and various reaction intermediates is highly desired. Here, we performed periodic, self-consistent density functional theory (DFT-GGA) calculations to study the adsorption of five atomic species (H, C, N, O, and S), seven molecular species (NH 3 , CH 4 , N 2 , CO, HCN, NO, and HCOOH), and 13 molecular fragments (CH, CH 2 , CH 3 , NH, NH 2 , OH, CN, COH, HCO, COOH, HCOO, NOH, and HNO) on the Cu(111) surface at a coverage of 0.25 monolayer. The preferred binding site, binding energy, and the corresponding surface deformation energy of each species were determined, as well as the estimated diffusion barrier and diffusion pathway. The binding strengths calculated using the PW91 functional decreased in the following order: CH > C > O > S > CN > NH > N > CH 2 > OH > HCOO > COH > H > NH 2 > NOH > COOH > HNO > HCO > CH 3 > NO > CO > NH 3 > HCOOH. No stable binding structures were observed for N 2 , HCN, and CH 4 . The adsorbate–surface and intramolecular vibrational modes of all the adsorbates at their preferred binding sites were deternined. Using the calculated adsorption energetics, potential energy surfaces were constructed for the direct decomposition of CO, CO 2 , NO, N 2 , NH 3 , and CH 4 and the hydrogen-assisted decomposition of CO, CO 2 , and NO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Physics-informed neural networks for identification of material properties using standing waves

A metallic structure in its initial stage of failure involves plastic deformation or environmental degradation that changes the elastic modulus and density. This work presents the detection of change in wave velocity (a function of elastic modulus and density) as a system identification problem. A physics-informed neural network (PINN) is proposed to solve the system identification problem. The PINN takes the spatial coordinates of scanning locations and time as inputs and provides the displacement and wave velocity as outputs. The governing partial differential equation of standing waves in a rod is incorporated into the neural network as physics in the form of a loss function. The wave velocity vector is randomly initiated. During the training of the network, physics is used to determine and update the wave velocity target vector from the network’s displacement predictions. The measured data, comprising sparse displacement response on the rod structure, are used to train the PINN. The wave velocity at the sparse locations on the rod is learned from the predicted displacements during the training. Using the predictions of the trained network, the response of free vibration or material property variation can be reconstructed at unscanned locations on the structure to obtain high-resolution maps for full-field imaging to detect and localize the changes caused by plastic deformation. The PINN’s sparse scanning and simultaneous prediction capability during training can lead to high scanning and data-processing speeds. This capability yields a nondestructive evaluation system that can predict the presence of degraded material locations as the structural vibrations are scanned and processed in real time.

Rathod, Vivek↗
DOE OSTI2021

The 3D printing and modeling of functionally graded Kelvin foams for controlling crushing performance

Mechanical impact protection is an important consideration in many applications, ranging from product transportation to sports. Cellular materials are typically used due to their desirable energy absorption properties and light weight. However, their large deformation and rate dependent responses (especially of polymer foams) are challenging to consider in design. Additionally, the use of foams with uniform properties, such as uniform density and uniform stiffness, often restricts the designed foams to only be suitable for a narrow range of mechanical impact conditions whereas real applications commonly face unpredictable situations. 3D printing offers fabrication flexibility and thus opens the door to create foams with tailored properties. In this work, we investigate the feasibility of using 3D printing for functionally graded foams (FGFs) that are optimal over a broad range of mechanical environments. The foams are fabricated by the recently developed grayscale digital light processing (g-DLP) method which can print parts with locally designed properties. These foams are tested under drop test conditions and with slower displacement control. We also model the large deformation behavior of FGFs using finite element analysis in which we account for the different viscoelastic behaviors of the distinct grayscale regions. We then use the model to examine the impact mitigation capabilities of FGFs in different loading scenarios. Finally, we show how FGFs can be used to satisfy real-world design goals using the case study of a motorcycle helmet. In contrast to prior work, we investigate continuous, functionally graded foams of a single density that differ in their viscoelastic responses. This work provides further insight into the benefits of viscoelastic properties and modulus graded foams and presents a manufacturing approach that can be used to produce the next generation of flexible lattice foams as mechanical absorbers.

3D printing↗
DOE OSTI2016

Overall picture of the cascade gamma decay of neutron resonances within a modified practical model

The intensities of two-step cascades in 43 nuclei of mass number in the range of 28 ≤ A ≤ 200 were approximated to a high degree of precision within a modified version of the practical cascade-gammadecay model introduced earlier. In this version, the rate of the decrease in the model-dependent density of vibrational levels has the same value for any Cooper pair undergoing breakdown. The most probable values of radiative strength functions both for E1 and for M1 transitions are determined by using one or two peaks against a smooth model dependence on the gamma-transition energy. The statement that the thresholds for the breaking of Cooper pairs are higher for spherical than for deformed nuclei is a basic result of the respective analysis. The parameters of the cascade-decay process are now determined to a precision that makes it possible to observe the systematic distinctions between them for nuclei characterized by different parities of neutrons and protons.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

On the temperature and density dependence of dislocation drag from phonon wind

At extreme strain rates, where fast moving dislocations govern plastic deformation, anharmonic phonon scattering imparts a drag force on the dislocations. In this paper, we present calculations of the dislocation drag coefficients of aluminum and copper as functions of temperature and density. We discuss the sensitivity of the drag coefficients to changes in the third-order elastic constants with temperature and density.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Microscopic origin of reflection-asymmetric nuclear shapes

The presence of nuclear ground states with stable reflection-asymmetric shapes is supported by rich experimental evidence. Theoretical surveys of odd-multipolarity deformations predict the existence of pear-shaped isotopes in several fairly localized regions of the nuclear landscape in the vicinity of near-lying single-particle shells with Δℓ = Δj = 3. We analyze the role of isoscalar, isovector, neutron-proton, neutron-neutron, and proton-proton multipole interaction energies in inducing the onset of reflection-asymmetric ground-state deformations. The calculations are performed in the framework of axial reflection-asymmetric Hartree-Fock-Bogoliubov theory using two Skyrme energy-density functionals and density-dependent pairing force. We show that reflection-asymmetric ground-state shapes of atomic nuclei are driven by the odd-multipolarity neutron-proton (or isoscalar) part of the nuclear interaction energy. This result is consistent with the particle-vibration picture, in which the main driver of octupole instability is the isoscalar octupole-octupole interaction giving rise to large E3 polarizability. The necessary condition for the appearance of localized regions of pear-shaped nuclei in the nuclear landscape is the presence of parity doublets involving Δℓ = Δj = 3 proton or neutron single-particle shells. This condition alone is, however, not sufficient to determine whether pear shapes actually appear, and, if so, what the corresponding reflection-asymmetric deformation energies are. The predicted small reflection-asymmetric deformation energies result from dramatic cancellations between even- and odd-multipolarity components of the nuclear binding energy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

A new coupled multiphase flow–finite strain deformation–fault slip framework for induced seismicity

Production of hydrocarbons and water from subsurface reservoirs are known to cause permanent deformation of the reservoir and seismicity along faults both of which are detrimental to sustainable development of natural resources. Most of the prior studies on understanding fluid flow-induced plasticity and seismicity have focused on one or the other phenomenon due to the numerical difficulty associated with simultaneous modeling of the two failure phenomena because stress and deformation evolve non-linearly in both plasticity and seismicity. However, in reservoirs undergoing long-term production, plastic failure can alter the stress paths of points on a fault such that the onset, location, and magnitude of actual seismic events can no longer be predicted by a poroelastic simulation due to inaccurate stress and deformation history. We present a computational framework for coupled multiphase flow, finite strain poroplastic deformation, and dynamic fault slip and use it to understand the impact of plastic deformation on the onset, location, and magnitude of induced fault slip events. We evaluate the impact of plasticity on reservoir pressure, deformation, induced stress, and fault slip by comparing infinitesimal strain elastic and finite strain poro-elastoplastic models. For real-world applications, we consider different scenarios where the reservoir is either mechanically weaker or stronger than the caprock. We analyze the stress evolution as a function of the change in reservoir pressure to understand the role of contrast in reservoir and caprock elastic moduli on geomechanical stability. The results show that the poroplastic reservoir exhibits larger vertical deformation and delayed slip than the poroelastic reservoir after the same amount of oil production. For the same amount of pressure drop, a reservoir with a smaller modulus than the caprock displays a larger vertical displacement and an earlier onset of both plastic failure and fault slip. For a reservoir with a larger modulus than the caprock, vertical displacement is larger on the reservoir top boundary and smaller on the ground surface, and a higher pressure drop is needed to induce plastic failure and fault slip.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗