Search NASA⌕ Search

SEARCH · Search NASA

Results for “depth sectioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Investigating Fifth Oxide Effect on CMXAS Glass Properties

Coatings for hot section aero turbine engine structural materials are subject to thermochemical degradation after interacting with calcium-magnesium-aluminosilicates (CMAS). Molten CMAS viscosity is the primary glass property of importance, correlating with coating infiltration and reaction depth. CMAS viscosity was measured using a spindle-dipped viscometer at temperatures between 1300-1550°C in 25°C increments. Experimental data were compared to Thermo-Calc and FactSage computational models, which showed good agreement with experimental trends. CMXAS compositions, where X denotes a fifth oxide, of Ca30.75-Mg9-X5-Al13-Si42.25 (single cation oxide mol%) for X = Fe2+, Fe3+, Gd3+, Hf4+, Na1+, Ti4+, Y3+, Yb3+, Zr4+ additions were used. Oxide precipitation was observed in X = Hf4+ , Zr4+ CMXAS specimens, indicating coating dissolution is an increased threat for T ≥ 1390°C. Molten CMAS and CMXAS viscosity measurements were shown to correlate with net cation field strength, offering an alternative in property prediction where thermodynamic data are unavailable.

Clark Avery Luckhardt↗
NASA NTRS2002

Floating Probe Assembly for Measuring Temperature of Water

A floating apparatus denoted a temperature probe aquatic suspension system (TPASS) has been developed for measuring the temperature of an ocean, lake, or other natural body of water at predetermined depths. Prior instruments built for the same purpose were found to give inaccurate readings because the apparatuses themselves significantly affected the temperatures of the water in their vicinities. The design of the TPASS is intended to satisfy a requirement to minimize the perturbation of the temperatures to be measured. The TPASS includes a square-cross-section aluminum rod 28 in. (approx. = 71 cm) long with floats attached at both ends. Each float includes five polystyrene foam disks about 3/4 in. (approx. = 1.9 cm) thick and 2.5 in. (approx. = 6.4 cm) in diameter. The disks are stacked to form cylinders, bolted to the rod, and covered with hollow plastic sleeves. A metal sleeve is clamped to the middle of the aluminum rod, from whence it hangs down into the water. Temperature probes (which can be thermocouples, thermistors, or resistance temperature devices) are placed within the sleeve at the desired measurement depths. Wires from the temperature probes are routed to the input terminals of a data logger. This work was done by Randy

Selinsky, T.↗
DOE OSTI2021

Collisional excitation of interstellar PN by H 2 : New interaction potential and scattering calculations

Here, rotational excitation of interstellar PN molecules induced by collisions with H 2 is investigated. We present the first ab initio four-dimensional potential energy surface (PES) for the PN–H 2 van der Waals system. The PES was obtained using an explicitly correlated coupled cluster approach with single, double, and perturbative triple excitations [CCSD(T)-F12b]. The method of interpolating moving least squares was used to construct an analytical PES from these data. The equilibrium structure of the complex was found to be linear, with H 2 aligned at the N end of the PN molecule, at an intermolecular separation of 4.2 Å. The corresponding well-depth is 224.3 cm -1 . The dissociation energies were found to be 40.19 cm -1 and 75.05 cm -1 for complexes of PN with ortho-H 2 and para-H 2 , respectively. Integral cross sections for rotational excitation in PN–H 2 collisions were calculated using the new PES and were found to be strongly dependent on the rotational level of the H 2 molecule. These new collisional data will be crucial to improve the estimation of PN abundance in the interstellar medium from observational spectra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Groundwater table elevation and temperature from 2015 to 2024 at the Lower Montane site in the East River Watershed, Colorado.

This groundwater level elevation and temperature data package is aimed at improving the predictive understanding of hydro-biogeochemical processes at the lower montane site in the East River Watershed, Colorado. The dataset is obtained using pressure transducers placed in shallow wells in the floodplain. This dataset contains data from wells with Location ID's ER-DOW (alias DO1West), ER-DOE (alias DO2East), ER-MBA1 (alias M1Bend1), ER-MBA2 (alias M1Bend2), ER-UPW (alias UP1West), ER-UPM (alias UP2), ER-UPE (alias UP3East). Another dataset contains the data from wells with Location ID's ER-CPA1 to ER-CPA6. Each file contains the water level elevation and the water temperature. Water level elevation has been obtained using the barometric pressure from the pressure transducer (Hobos sensor) in the well, barometric pressure from a sensor in air located at the same site (lower montane), depth from top-of-casing (TOC) to sensor measurement point, and TOC elevation. Data have been checked with a few measurements of water table depths. A real-time kinematic (RTK) global positioning system (GPS) has been used to survey the TOC (data in file Well_Location.csv). The water level elevation is given in UTM13N Geoid2012AB. While depth to water level is not present in the data files, it can be easily calculated with the TOC and distance to ground provided in the GPS coordinate file. The dataset quality is discussed in Collection/Analysis section of the methods. Time-series of measurements were initially added to the archive for the period 2015 to 2019, and later updated with time-series until 2024 (end of data collection). The dataset contains 8 *.csv data files, and 3 *.csv metadata files. Feel free to contact the author with any questions or collaboration interests. The publication year was updated from "2020" to "2025" to reflect the revised version of this dataset.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Groundwater table elevation and temperature from 2015 to 2024 across Meander C at the Lower Montane site in the East River Watershed, Colorado.

This groundwater level elevation and temperature data package is aimed at improving the predictive understanding of hydro-biogeochemical processes at the lower montane site in the East River Watershed, Colorado. The dataset is obtained using pressure transducers placed in shallow wells in the floodplain. This dataset contains data from wells ER-CPA1 to ER-CPA6. Another dataset contains the data from wells at nearby Locations. Each file contains the water level elevation and the water temperature. Water level elevation has been obtained using the barometric pressure from the pressure transducer (Hobos sensor) in the well, barometric pressure from a sensor in air located at the same site (lower montane), depth from top-of-casing (TOC) to sensor measurement point, and TOC elevation. Data have been checked with a few measurements of water table depths. A real-time kinematic (RTK) global positioning system (GPS) has been used to survey the TOC (data in file Well_Location.csv). The water level elevation is given in UTM13N Geoid2012AB. While depth to water level is not present in the data files, it can be easily calculated with the TOC and distance to ground provided in the GPS coordinate file. The dataset quality is discussed in Collection/Analysis section of the methods. Time-series of measurements were initially added to the archive for the period 2015 to 2019, and later updated with time-series until 2024 (end of data collection). The dataset contains 7 *.csv data files, and 3 *.csv metadata files. Feel free to contact the author with any questions or collaboration interests. The publication year was updated from "2020" to "2025" to reflect the revised version of this dataset.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1993

Three-D crater analysis of LDEF impact features from stereo imagery

The preliminary results from attempts to derive depth and diameter information from digitized stereo images of impact features on the LDEF are reported. Contrary to our prior assumption, we find that impact craters in the T6 A1 alloy are not paraboloid in cross section, but rather are better described by a 6th-order polynomial curve. We explore the implications of this discovery.

Sapp, Clyde A.↗
DOE OSTI2021

Deep learning inversion of gravity data for detection of CO 2 plumes in overlying aquifers

In this work, we developed an effective U-Net based deep learning (DL) model for inversion of surface gravity data on a rectangular grid to predict 2-D high-resolution subsurface CO 2 distribution along a vertical cross-section due to CO 2 leakage through a wellbore within a deep CO 2 storage reservoir. We used synthetic data to model two types of CO 2 leakage scenarios: one CO 2 plume in a shallow aquifer (single plume case), and two plumes present at different depths (double plume case). The 3-D synthetic plume samples were created by sampling among predetermined CO 2 plume depths, saturations, and volumes. The corresponding surface gravity data on a rectangular grid were generated by a 3-D forward model. The U-Net model detected 72% of single-plume samples, and one or both plumes in 75% of double-plume samples. Most of the undetected single plumes have small gravity field strengths below the typical noise level of 5 μGal. This model generated reproducible, reliable predictions with acceptable errors and demonstrated improved spatial resolution over the conventional least-squares inversion. In contrast to the conventional least-squares inversion, which often overestimates the size of its target and underestimates its density, this U-Net model accurately delineated the boundary of a target. Furthermore, this DL inversion detected deep, small, or low saturation CO 2 plumes that are often more difficult to resolve with conventional gravity inversion methods. We note the limitations of this feasibility study, including the use of synthetic data with regular CO 2 plume shapes, and the prediction of a 2-D plume cross-section rather than the full 3-D plume, as well, we recognize the lower detection fraction for double-plume scenarios. Nevertheless, this study demonstrates that DL gravity inversion is a promising and potentially superior method to conventional least-squares inversion. Our U-Net based deep learning inversion approach may be adapted for inversion of other types of geophysical data. DL inversion can facilitate near real-time monitoring of geologic carbon sequestration to provide site operators with prompt information about subsurface CO 2 distribution for risk management and mitigation.

58 GEOSCIENCES↗
NASA NTRS1989

Probabilities for gravitational lensing by point masses in a locally inhomogeneous universe

Probability functions for gravitational lensing by point masses that incorporate Poisson statistics and flux conservation are formulated in the Dyer-Roeder construction. Optical depths to lensing for distant sources are calculated using both the method of Press and Gunn (1973) which counts lenses in an otherwise empty cone, and the method of Ehlers and Schneider (1986) which projects lensing cross sections onto the source sphere. These are then used as parameters of the probability density for lensing in the case of a critical (q0 = 1/2) Friedmann universe. A comparison of the probability functions indicates that the effects of angle-averaging can be well approximated by adjusting the average magnification along a random line of sight so as to conserve flux.

Isaacson, Jeffrey A.↗
NASA NTRS1959

Hydrodynamic Characteristics of Two Low-Drag Supercavitating Hydrofoils

An experimental investigation has been conducted in Langley tank no. 2 to determine the hydrodynamic characteristics of two low-drag supercavitating hydrofoils operating in a range of cavitation numbers from 0 to approximately 6. The hydrofoils had aspect ratios of 1 and 3, and the sections were derived by assuming five terms in the vorticity-distribution expansion of the equivalent airfoil. The aspect-ratio-1 hydrofoil was also tested at zero cavitation number with two sets of end plates having depths of 3/8 and 1/4 chords. Zero cavitation number was established by operating the hydrofoils near the water surface so that complete ventilation of the upper surfaces could be obtained. For those depths of submersion where complete ventilation was not obtained through vortex ventilation, two probes were used to introduce air to the upper surfaces of the hydrofoils and to induce complete ventilation. Data were obtained for a range of speeds from 20 to 80 fps, angles of attack from 2 to 20 deg, and ratios of depth of submersion to chord from 0 to 0.85. The experimental results obtained from the aspect-ratio-1 and aspect-ratio-3, five-term hydrofoils were compared with a three-dimensional zero-cavitation-number theory. The theoretical and experimental values of lift and center of pressure for the aspect-ratio-1 hydrofoil were in agreement, within engineering accuracy, for the range of lift coefficients investigated. The theoretical drag coefficients were lower, by a constant amount, than the experimental drag coefficients. The theoretical expressions derived for the lift, drag, and center of pressure of the aspect-ratio-3 hydrofoil were in agreement, within engineering accuracy, with the experimental values. The theoretical and experimental drag coefficients of the aspect-ratio-3 five-term hydrofoil were lower than the theoretical drag coefficients computed for a comparable Tulin-Burkart hydrofoil.

McGehee, John R.↗
NASA NTRS2012

Chemical Mapping of Vesta

Vesta s surface mineralogy and composition have been studied for decades via telescopic spectroscopy and laboratory analyses of the howardite, eucrite, and diogenite (HED) meteorites, which are thought to originate from Vesta. Visible and infrared reflectance measurements by Dawn have broadly confirmed the paradigm established by Earth-based work, strengthening the Vesta-HED connection. The Dawn mission has achieved a milestone by completing the first chemical measurements of a main-belt asteroid using nuclear spectroscopy. Dawn s Gamma Ray and Neutron Detector (GRaND) has globally mapped the composition of Vesta, including the portions of the northern hemisphere not illuminated by solar radiation. GRaND is sensitive to the composition of the bulk regolith to depths of several decimeters. Abundances and/or detection limits for specific elements and elemental ratios, such as H, Fe, Si, Fe/O, Fe/Si, and K, have been measured. Variations in the average atomic mass and neutron macroscopic absorption cross section have been characterized. The measurements constrain the relative proportions of HED whole-rock end-members, providing measurements of the pyroxene and plagioclase content of the regolith, thereby constraining the processes underlying Vesta s differentiation and crustal evolution. The spatial resolution of GRaND is sufficient to determine basin-average compositions of Veneneia and Rheasilvia, which may contain outcrops of Vesta s olivine-rich mantle. While the elemental composition of Vesta s regolith is similar to the meteorites, there are notable departures from HED whole-rock compositions. While these differences are not sufficient to topple the Vesta-HED paradigm, they provide insight into global-scale processes that have shaped Vesta s surface. Questions addressed by the analysis of GRaND data include: (i) Is Vesta the source of the Fe-rich mesosiderites? (ii) Are evolved, igneous lithologies present on Vesta s surface? (iii) What are the origins of exogenic materials found in Vesta s regolith? (iv) Is the vestan mantle exposed within the southern basins?

Prettyman, Thomas H.↗
DOE OSTI2020

Complexity of Fault Rupture and Fluid Leakage in Shale: Insights From a Controlled Fault Activation Experiment

Abstract We observed rupture growth caused by controlled fluid injections at 340‐m depth within a fault zone in the low‐permeability Opalinus Clay in the Mont Terri Underground Research Laboratory (Switzerland). The rupture mechanisms were evaluated using measurements of the three‐component borehole wall displacements and fluid pressure in two sections of the fault zone and located horizontally 3 m apart from each other. One section was set across a secondary segment of the fault and used for stepwise fluid injection intended to trigger rupture growth. The other section was set across the principal shear zone of the fault for monitoring. After stepwise pressure increase up to 5.95 MPa at injection, rupture initiated as slip activation, followed by an overall opening of the fault planes connected to the injection. After 19 s of continued injection, displacements arrived at the monitoring point on the principal shear zone. These displacements are about 2.4 times larger than in the secondary fault segment. Overall, the displacements corresponded to a normal fault activation. About 9 s after the displacement front arrived, a strong pressure increase of 4.17 MPa was measured at the monitoring point, indicating a hydraulic connection had formed along the initially very low permeability fault planes between the injection and the monitoring points. Our analyses highlight that the fault activation is consistent with the state of stress but that injection pressure must be close to the normal stress acting on the fault for permeability to be generated and for fluid leakage to occur.

Guglielmi, Yves↗
DOE OSTI2022

Development of an Open-source Alloy Selection and Lifetime Assessment Tool for Structural Components in CSP

Lack of sufficient data on high temperature mechanical and corrosion behavior of structural materials is a huge barrier in the technological maturity of current and future Concentrating Solar Power (CSP) technologies. Rapid development and selection of materials cannot be achieved by expensive and time-consuming acquisition of experimental data. The goal of the proposed work is development of an open-source alloy selection and lifetime prediction tool that will integrate validated physics-based models to describe influence of temperature, alloy composition, environment and component geometry (thickness) on mechanical and corrosion behavior of Ni and Fe-based alloys employed in molten salts/sCO 2 heat exchangers. This one-year project leveraged the extensive dataset on the creep\corrosion behavior of candidate materials generated at ORNL through past projects and input from current collaborations with industrial partners. Based on previous experience and the feedback provided by industry (Brayton Energy and Echogen), three candidate materials of interest, Ni-based alloys 740H, 282 and 625 and application-specific operating conditions (max. temperature of 730 °C and stress of 150 MPa) were identified for the heat exchanger. An extensive corrosion and creep dataset was assimilated for the relevant operating conditions and was supported by detailed characterization of about 100 metallographic cross-sections. The corrosion dataset consisted of scanning electron microscopy images (secondary electron and backscatter electron), measured concentration profiles of alloying elements using energy dispersive X-ray spectroscopy (EDS), widths of denuded zones (dissolution of strengthening phases) and depths of attack in molten KCl-MgCl 2 mixtures using image analyses. The creep dataset comprised of creep rupture data and creep strain curves (for 740H and 282). Coupled thermodynamic-kinetic microstructure-based models were employed to predict the stress-corrosion induced compositional and phase evolutions in the alloy during operation under the identified operating conditions. Reduced order models were developed from advanced physics-based models and were integrated in a user-friendly alloy selection tool. The corrosion model was able to predict the time to a critical Cr concentration at the oxide/alloy interface (chemical lifetime) within ±10% (1 standard deviation) of typical statistical variation in corrosion tests and EDS measurement errors (±0.5 wt%). The initial scope of the project was limited to predict creep rupture times (Larson-Miller parameter). Based on the input provided by industry, the mechanical lifetime of the heat exchanger is governed by accumulated creep strains (2%) rather than creep rupture. To be able to predict the times to specific creep strains, a more extensive creep model development was undertaken largely beyond the initial scope of the project. The continuum damage mechanics creep model was able to predict times to 2% creep strain, t 2% with an accuracy of ±500h. Ultimately, a screening protocol for SiC was generated to demonstrate the pathway for integration of one of the currently immature materials from a commercial adoption standpoint in the current material evaluation tool. The modeling tool developed here is accessible to the science community and stakeholders and lays the foundation for methods that will enable a rapid evaluation of optimum materials for CSP applications and reliable prediction of material degradation thereby considerably reducing operational costs, improving reliability and increasing overhaul intervals. However, the complete potential of such a tool to include a wider range of materials and test conditions can only be realized with a more concentrated combined experimental-characterization-computation effort.

14 SOLAR ENERGY↗
DOE OSTI2024

DECOVALEX-2023: Task G, SAFENET Final Report

DECOVALEX Task G deals with fracture mechanics at several scales using a combined approach of experimental work, related model development, benchmarking and experimental analysis. Fig. 0.1 provides a graphical abstract for Task G. The experimental basis for the related mechanical (M), hydro-mechanical (HM), and thermo-mechanical (TM) processes comes from the rock mechanics laboratories of Universities of Freiberg (TUBAF) and Edinburgh, as well as the Korea Institute of Civil Engineering and Building Technology (KICT). The experimental work in the rock laboratories is closely linked to the underground research laboratories (URLs) Reiche Zeche (Germany), KURT (Korea), and Mont Terri (Switzerland). The scientific key questions are related to fracture permeability evolution under THM conditions, anisotropy effects on fracturing processes, and thermal fracture slip, which are being addressed in specific steps of the task. A large variety of numerical methods have been developed and applied for experimental analysis, ranging from continuum to discontinuum approaches. A detailed comparison of mechanical and hydro-mechanical processes is given in the section 3 via the benchmarking exercises. As a result of DECOVALEX-2023 Task G we further improved our understanding and predictability of fracturing processes under THM conditions. This was based on robust numerical simulation methods and in-depth experimental analysis.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Structural Evolution of the Hogback Monocline and Its Tectonic Significance in the San Juan Basin

The San Juan Basin is recognized as a Laramide foreland basin. It is located within the Colorado Plateau, a broad tectonic province characterized by a thick sedimentary sequence that was segmented into smaller sub basins during the Late Cretaceous to Paleogene Laramide orogeny. The Hogback Monocline lies along the northwestern margin of the San Juan Basin and is considered a Laramide-age structure formed in response to compressional stress. In this study, we interpret surface and subsurface datasets to construct a structural geological model and evaluate its tectonic significance. Through seismic data, we identify key fault and fold geometries at depth. The seismic dataset used in this study was reprocessed in depth and constrained with well log velocity data to enhance seismic imaging quality. Additionally, we performed well log correlations to identify formation tops and assess variations in basin infill and thickness geometry. A series of structural cross-sections, constructed using seismic data and a high density of boreholes, are presented to evaluate geometric variations along the structure and its evolution during basin development. Furthermore, kinematic restoration and forward modeling analyses were conducted to validate our structural interpretation. This work suggests that the Hogback Monocline formed through fault-propagation folding and flexural slip affecting the pre-Laramide sedimentary sequence under compressional stresses associated with the Laramide orogeny. This structure is interpreted as a high-angle reverse fault that influenced the geometry of the late basin infill. Additionally, monocline bending along the structure may have been controlled by fault relay systems and, in some cases, influenced by strike-slip faulting.

Reyes, Martin [New Mexico Bureau o fGeology and Mi↗
NASA NTRS1975

Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps, phase 2. Volume 1: Technical report

Heat transfer data measured in gaps representative of those being employed for joints in the space shuttle reusable surface insulation (RSI) thermal protection systems (TPS) were assimilated, analyzed, and correlated. Several types of gap were investigated with emphasis on simple butt joints. Gap widths ranged from 0.0 to 0.76 cm and depths ranged from 1 to 6 cm. Laminar, transitional, and turbulent boundary layer flows over the gap opening were investigated. The angle between gap axis and external flow was varied between 0 and pi/2 radians. The contoured cross section gap performed significantly better than all other wide gaps and slightly better than all other narrow gap geometries. Three dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Interactions between heating within gaps and heating of adjacent top tile surfaces were observed. Gaps aligned with the flow were observed to promote boundary layer transition. Heat transfer correlation equations were obtained for many of the tests. The TPS thickness requirements with and without gaps were computed for a current shuttle entry trajectory. Experimental data employed in the study are summarized. A description of each test facility, run schedule and test conditions, model descriptive information, and heat flux data are included.

Cristensen, H. E.↗
DOE OSTI2023

Schneider Springs Fire Study 2023 for Ecosystem Respiration Rates: Surface Water Chemistry and Hydrologic Sensor Data across the Yakima River Basin, Washington, USA (v2)

This dataset supports a broader study examining the drivers of spatial variability in wildfire impacts across the Yakima River Basin. Data provided within this dataset were generated from sample collection across 17 total sites (8 sites affected by a recent wildfire, 9 sites unaffected by a recent wildfire) within multiple rivers throughout the Yakima River Basin in Washington, USA from May-July 2023. Fire affected sites are defined as those affected by the 2021 Schneider Springs Fire, based on the drainage area of the streams being within the 2021 Schneider Springs Fire burn perimeter or not (Figure 1, below). The contents include surface water geochemistry data (dissolved organic carbon; total dissolved nitrogen; total suspended solids); short-term sonde data (specific conductivity; turbidity; pH; chlorophyll A; temperature); stream depth data; stream velocity; manual chamber open channel respiration data; sensor time-series data (oxygen; water pressure; barometric pressure); field metadata (including qualitative information on in stream and river corridor characteristics); and environmental context photos taken in the field. The dataset also includes a summary file of the sensor data and plots of the sensor data. Sensors were only recovered at 15 out of the 17 sites, and not all sensors were recovered at all 15 sites (see Methods section for more details), therefore all data does not exist at all sites. Data from a 2022 study at the same sites, as well as additional sites, can be found at https://data.ess-dive.lbl.gov/view/doi:10.15485/1969566. The data package was originally published in November 2023. It was updated in June 2025 (v2; modified files). See the change history section in the readme for more details. For details on how to navigate data packages generated by this project, see https://data.ess-dive.lbl.gov/portals/PNNLRiverCorridorSFA/About. This dataset is comprised of one folder with field photos and one main data folder with two subfolders. The main data folder consists of (1) file-level metadata; (2) data dictionary; (3) field metadata; (4) field protocol; (5) readme; (6) international generic sample number (IGSN) mapping file; and (7) stream depth and averages. The sensor data subfolder consists of (1) sensor installation methods summary; (2) stream velocity; and (3) six subfolders. The BarotrollAtm (barometric pressure; temperature), DepthHOBO (water pressure; temperature), MantaRiver (specific conductivity; turbidity; pH; chlorophyll A; temperature), EXO (specific conductivity; pH; temperature), miniDOT (dissolved oxygen; temperature), and miniDOTManualChamber (dissolved oxygen; temperature) contain time-series data, plots, and summary files. The sample data subfolder consists of (1) total suspended solids (TSS) data; (2) dissolved organic carbon (DOC, measured as non-purgeable organic carbon, NPOC) data and averages; (3) total dissolved nitrogen (TN) data and averages; and (4) methods codes. All files are .csv, .pdf, .jpg, .jpeg, or .mov.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Narrow-Channel, Fluidized Beds for Effective Particle Thermal Energy Transport and Storage

Colorado School of Mines (Mines) led this program in collaboration with Sandia National Laboratories (Sandia) to characterize narrow-channel fluidized beds of aluminosilicate particles – supplied by Carbo Ceramics – as a means for releasing high-temperature thermal energy in particle heat exchangers and for capturing concentrated solar energy in indirect particle receivers. Single-channel, heat transfer experiments at Mines and reduced-order 1-D models and 3-D two-fluid, CFD models explored many aspects of counterflow, bubbling fluidized beds (net downward particle flow and upward gas flow) for enhancing particle-wall heat transfer at elevated temperatures. Results at Mines on single-channel test sections consistently showed that mild bubbling fluidization increases particle-wall heat transfer coefficients (h T,w ) regularly by more than 4.0x over h T,w values without fluidization at similar conditions (mean particle diameter d p , bed depth Δz b , and bed particle temperatures T p ). Insights from lab-scale tests and modeling studies provided Nusselt number correlations for h T,w and informed the design and fabrication (by Vacuum Process Engineering) of a nominal 40-kWth, particle-sCO 2 plate heat exchanger (HX) with 12 parallel narrow-channel, fluidized beds bounded by stainless-steel walls with embedded microchannels for high-pressure sCO 2 flows. Tests of the 40-kW th HX at the particle-sCO 2 HX test stand at Sandia's National Solar Thermal Test Facility (NSTTF) were limited, due to HX design, to particle inlet temperatures T p,in ≤ 520°C with maximum sCO 2 outlet temperatures T sCO2,out ≈ 440°C, which are well below design conditions for a primary HX in a sCO 2 power cycle for a Gen-3 concentrating solar power (CSP) plant. Total heat transfer $\dot{Q}_{HX}$ remains relatively constant with increased fluidization for fixed particle and sCO 2 inlet conditions because higher h T,w due to fluidization is offset by increased axial dispersion, which suppresses temperature differences between the particles and sCO 2 in the counterflow configuration. The axial dispersion reduces the effective overall heat transfer coefficient U based on T p,in to values around 200 W m -2 K -1 .

14 SOLAR ENERGY↗
NASA NTRS1974

Identification characteristics of certain lunar relief forms on pictures obtained from spacecraft

This investigation was restricted to the determination of recognitional characteristics of a single type of relief form, dimple craters on the surface of maria. These craters were arbitrarily considered as closed, negative relief forms, circular in plan-view, and symmetric relative to the center. Two techniques were used to determine the shadow configuration in the craters: (1) experimental determination of the shadow edge by illuminating the models of different profile shapes with a parallel light beam; and (2) geometric construction of the shadow edge using a vertical section of the formation in the direction of the solar rays. A morphological map of the surface which includes the following factors can be compiled using the proposed identification technique: crater profile nature, crater diameter, ratio of diameter and depth, sharpness of the lip, and distribution density of the forms.

Kravtsova, V. I.↗