Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffraction simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Local molecular environment drives speciation and reactivity of ion complexes in concentrated salt solution

The speciation and reactivity of aqueous salt solutions are important for a wide variety of applications. However, application of this information is inhibited by broad disagreement about composition, mechanisms, and structure in concentrated solutions especially. Here, neutron diffraction with isotopic substitution measurements on aqueous zinc chloride solutions are used to calibrate molecular dynamics simulations that include effective electronic polarization. This allows us to probe the origin of speciation and reactivity of zinc chloride-water ion complexes, ZnCl x (H 2 O) y 2-x (x ≤ 4 and y ≤ 6), by comparing the reactivity of species in concentrated (4.5 m) and dilute (0.01 m) conditions. Within the concentrated solution, it is found that the extended solvation environment is dominated by solvent-separated ion complexes whose presence increases the free energy of activation for interconversion of species while simultaneously enhancing their thermodynamic stability. This concentration-dependent reactivity and stability suggests that other reactions, such as the nucleation of solid phases, will also be affected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Nanometer-Scale Correlations in Aqueous Salt Solutions

The intermediate-range (1–4 nm) correlation of cations, an- ions, and water in aqueous alkaline earth salt solutions is measured using synchrotron X-ray diffraction. We differentiate from the entire solution structure factor, S(Q), a separate region at low Q (<1 °A-1) containing local diffraction maxima (pre-peaks) that indicate nanometer-scale oscillatory behavior. These features are quantitatively reproduced with classical molecular dynamics simulations. At high concentrations, the pre-peaks emerge from correlations arising from existence of small quasi close-packed lattice- like structures comprised of cation hydration spheres. We also analyze the concentration dependence of the pre-peak and discuss the overall results in light of the rich literature dealing with intermediate-range correlations underlying universal phenomena in concentrated electrolytes. The authors were supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences. Pacific Northwest National Laboratory (PNNL) is operated by Battelle for the U.S. Department of Energy under Contract No. DE-AC05-76RL01830. Computing resources were generously allocated by PNNL's Institutional Computing program. DOE Contract No. DEAC02- 06CH11357 supports operation of the Advanced Photon Source at Argonne National Laboratory.

Chemical physics, nucleation, Madelung potential↗
DOE OSTI2023

A New Sodium Thioborate Fast Ion Conductor: Na 3 B 5 S 9

Abstract We report a new sodium fast‐ion conductor, Na 3 B 5 S 9 , that exhibits a high Na ion total conductivity of 0.80 mS cm −1 (sintered pellet; cold‐pressed pellet=0.21 mS cm −1 ). The structure consists of corner‐sharing B 10 S 20 supertetrahedral clusters, which create a framework that supports 3D Na ion diffusion channels. The Na ions are well‐distributed in the channels and form a disordered sublattice spanning five Na crystallographic sites. The combination of structural elucidation via single crystal X‐ray diffraction and powder synchrotron X‐ray diffraction at variable temperatures, solid‐state nuclear magnetic resonance spectra and ab initio molecular dynamics simulations reveal high Na‐ion mobility (predicted conductivity: 0.96 mS cm −1 ) and the nature of the 3D diffusion pathways. Notably, the Na ion sublattice orders at low temperatures, resulting in isolated Na polyhedra and thus much lower ionic conductivity. This highlights the importance of a disordered Na ion sublattice—and existence of well‐connected Na ion migration pathways formed via face‐sharing polyhedra—in dictating Na ion diffusion.

Zhou, Laidong↗
DOE OSTI2023

A New Sodium Thioborate Fast Ion Conductor: Na 3 B 5 S 9

Abstract We report a new sodium fast‐ion conductor, Na 3 B 5 S 9 , that exhibits a high Na ion total conductivity of 0.80 mS cm −1 (sintered pellet; cold‐pressed pellet=0.21 mS cm −1 ). The structure consists of corner‐sharing B 10 S 20 supertetrahedral clusters, which create a framework that supports 3D Na ion diffusion channels. The Na ions are well‐distributed in the channels and form a disordered sublattice spanning five Na crystallographic sites. The combination of structural elucidation via single crystal X‐ray diffraction and powder synchrotron X‐ray diffraction at variable temperatures, solid‐state nuclear magnetic resonance spectra and ab initio molecular dynamics simulations reveal high Na‐ion mobility (predicted conductivity: 0.96 mS cm −1 ) and the nature of the 3D diffusion pathways. Notably, the Na ion sublattice orders at low temperatures, resulting in isolated Na polyhedra and thus much lower ionic conductivity. This highlights the importance of a disordered Na ion sublattice—and existence of well‐connected Na ion migration pathways formed via face‐sharing polyhedra—in dictating Na ion diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Release dynamics of nanodiamonds created by laser-driven shock-compression of polyethylene terephthalate

Laser-driven dynamic compression experiments of plastic materials have found surprisingly fast formation of nanodiamonds (ND) via X-ray probing. This mechanism is relevant for planetary models, but could also open efficient synthesis routes for tailored NDs. We investigate the release mechanics of compressed NDs by molecular dynamics simulation of the isotropic expansion of finite size diamond from different P-T states. Analysing the structural integrity along different release paths via molecular dynamic simulations, we found substantial disintegration rates upon shock release, increasing with the on-Hugnoiot shock temperature. We also find that recrystallization can occur after the expansion and hence during the release, depending on subsequent cooling mechanisms. Our study suggests higher ND recovery rates from off-Hugoniot states, e.g., via double-shocks, due to faster cooling. Laser-driven shock compression experiments of polyethylene terephthalate (PET) samples with in situ X-ray probing at the simulated conditions found diamond signal that persists up to 11 ns after breakout. In the diffraction pattern, we observed peak shifts, which we attribute to thermal expansion of the NDs and thus a total release of pressure, which indicates the stability of the released NDs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exploring Cr and molten salt interfacial interactions for molten salt applications

Molten salts play an important role in various energy-related applications such as high-temperature heat transfer fluids and reaction media. However, the extreme molten salt environment causes the degradation of materials, raising safety and sustainability challenges. A fundamental understanding of material–molten salt interfacial evolution is needed. This work studies the transformation of metallic Cr in molten 50/50 mol% KCl–MgCl 2 via multi-modal in situ synchrotron X-ray nano-tomography, diffraction and spectroscopy combined with density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations. Notably, in addition to the dissolution of Cr in the molten salt to form porous structures, a δ-A15 Cr phase was found to gradually form as a result of the metal–salt interaction. This phase change of Cr is associated with a change in the coordination environment of Cr at the interface. DFT and AIMD simulations provide a basis for understanding the enhanced stability of δ-A15 Cr vs. bcc Cr, by revealing their competitive phase thermodynamics at elevated temperatures and probing the interfacial behavior of the molten salt at relevant facets. This study provides critical insights into the morphological and chemical evolution of metal–molten salt interfaces. Finally, the combination of multimodal synchrotron analysis and atomic simulation also offers an opportunity to explore a broader range of systems critical to energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Thermal disorder and phonon softening in the ferroelectric phase transition of lead titanate

We report a molecular dynamics study of ab initio quality of the ferroelectric phase transition in crystalline PbTi⁢O3. We model anharmonicity accurately in terms of potential energy and polarization surfaces trained on density functional theory data with modern machine learning techniques. Our simulations demonstrate that the transition has a strong order-disorder character, in agreement with diffraction experiments, and provide fresh insight into the approach to equilibrium across the phase transition. We find that the emergence and disappearance of the macroscopic polarization is driven by dipolar switching at the nanometer scale. We also computed the infrared optical absorption spectra in both the ferroelectric and the paraelectric phases, finding good agreement with the experimental Raman frequencies. Often, the almost ideal displacive character of the soft mode detected by Raman scattering in the paraelectric phase has been contrasted with the order-disorder character of the transition suggested by diffraction experiments. We settle this issue by showing that the soft mode coexists with a strong Debye relaxation associated with thermal disordering of the dipoles. The Debye relaxation feature is centered at zero frequency and appears near the transition temperature in both the ferroelectric and the paraelectric phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

The Effects of Synthesis Conditions on the Carbon Capture Capacity of Polyethylenimine Impregnated Protonated Titanate Nanotubes

Capture and storage of carbon dioxide emitted from power plants, which burn fossil fuels, is one of the best ways to mitigate climate change. Polyethylenimine (PEI) impregnated protonated titanate nanotubes (PEI-PTNTs) are efficient amine-modified solid adsorbents for post combustion carbon capture. This study is to investigate the effects of synthesis conditions of titanate nanotubes on the carbon capture capacity of PEI-PTNTs. PTNTs are synthesized using hydrothermal treatment of TiO 2 anatase powder at different temperatures and in different days, followed by washing with dilute HCl solution and deionized water. PEI-PTNTs are prepared by loading PEI (M.W. = 10,000) onto PTNTs at a weight ratio of 1:1 using a wet impregnation process. PTNTs and PEI-PTNTs are characterized using transmission electron microscopy, porosity and surface area analysis, powder X-ray diffraction, and Fourier transform infrared spectroscopy. CO 2 adsorption is conducted at 75 °C using simulated flue gas, and CO 2 desorption is performed at 110 °C by purging the adsorbent with dry nitrogen gas. CO 2 adsorption experiments demonstrate that the PEI-PTNTs synthesized at 130 °C within 3 or 5 days, have the highest CO 2 capture capacity. These optimized PEI-PTNTs have a significant potential to capture CO 2 from power plants.

Materials Science↗
DOE OSTI2023

Three-dimensional imaging using coherent x rays at grazing incidence geometry

We have developed a three-dimensional coherent diffraction imaging algorithm to retrieve phases of diffraction patterns of samples in grazing incidence small angle x-ray scattering experiments. The algorithm interprets the diffraction patterns using the distorted-wave Born approximation instead of the Born approximation, as in this case, the existence of a reflected beam from the substrate causes the diffraction pattern to deviate significantly from the simple Fourier transform of the object. Detailed computer simulations show that the algorithm works. Verification with real experiments is planned.

Yang, Yi↗
NASA NTRS1998

Systems Issues Pertaining to Holographic Optical Data Storage in Thick Bacteriorhodopsin Films

The optical data storage capacity and raw bit-error-rate achievable with thick photochromic bacteriorhodopsin (BR) films are investigated for sequential recording and read- out of angularly- and shift-multiplexed digital holograms inside a thick blue-membrane D85N BR film. We address the determination of an exposure schedule that produces equal diffraction efficiencies among each of the multiplexed holograms. This exposure schedule is determined by numerical simulations of the holographic recording process within the BR material, and maximizes the total grating strength. We also experimentally measure the shift selectivity and compare the results to theoretical predictions. Finally, we evaluate the bit-error-rate of a single hologram, and of multiple holograms stored within the film.

Downie, John D.↗
NASA NTRS2002

An Assessment of the Residual Stresses in Low Pressure Plasma Sprayed Coatings on an Advanced Copper Alloy

Modeling studies were conducted on low pressure plasma sprayed (LPPS) NiAl top coat applied to an advanced Cu-8(at.%)Cr-4%Nb alloy (GRCop-84) substrate using Ni as a bond coat. A thermal analysis suggested that the NiAl and Ni top and bond coats, respectively, would provide adequate thermal protection to the GRCop-84 substrate in a rocket engine operating under high heat flux conditions. Residual stress measurements were conducted at different depths from the free surface on coated and uncoated GRCop-84 specimens by x-ray diffraction. These data are compared with theoretically estimated values assessed by a finite element analysis simulating the development of these stresses as the coated substrate cools down from the plasma spraying temperature to room temperature.

Raj, S. V.↗
DOE OSTI2020

Drying Wet Stored and Corroded Magnox Fuel for Interim Dry Storage - 20187

To investigate the feasibility of drying corroded Magnesium alloy clad nuclear fuel, the corrosion products of inactive and unirradiated Magnox simulant dry corrosion product and dried corroded Magnox sludge were characterised by X-ray diffraction and thermogravimetric analysis. XRD identified brucite in the dried corrosion product and both brucite and hydromagnesite in the sludge. TGA identified mass loss on dehydration of ∼9.1% up to 250 deg. C and 27.9% from dehydroxylation up to 440 deg. C, with total mass loss of 41.9% up to 800 deg. C for the dried corrosion product. The sludge TGA showed 8.3% mass loss up to 250 deg. C from dehydration, 7.5% up to 330 deg. C from dehydroxylation and 31.4% mass loss up to 47.2% for decarbonation, with total mass loss of 49.2% up to 800 deg. C. Water removal up to 1.8 g was performed by cold vacuum drying (40 deg. C-120 deg. C) on a ≅14.8 g (wet) corroded Magnox sample. The process was monitored by observing pressure, dew point, temperature and gas flow changes supported by measuring the sample mass loss as water is removed. From these tests, it was observed that the dried corroded Magnox displayed some hygroscopic capacity which has implications for water retention following vacuum drying and the length of exposure required to achieve the desired dryness. Whilst at higher temperatures the water was removed faster, the increased temperature also risks the fuel cladding undergoing unwanted chemical reactions with the residual water during the process. However, at lower temperatures the achievable levels of dryness were reduced. Therefore, from these observations this work has identified that there is a temperature balance that may be necessary to optimise the drying process with respect to allowing the greatest level of dryness whilst restricting unwanted chemical reactions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Increased spatial coherence length from an asymmetric crystal reflection at grazing exit

Coherent X-ray imaging is an active field at synchrotron sources. The images rely on the available coherent flux over a limited field of view. At many synchrotron beamlines a double-crystal monochromator (DCM) is employed in a standard nondispersive arrangement. For coherent diffraction imaging it is advantageous to increase the available field of view by increasing the spatial coherence length (SCL) of a beam exiting such a DCM. Here, Talbot interferometry data together with ray-tracing simulations for a (+ − − +) four-reflection experimental arrangement are presented, wherein the first two reflections are in the DCM and the final fourth reflection is asymmetric at grazing exit. Analyses of the interferometry data combined with the simulations show that compared with the beam exiting the DCM a gain of 76% in the SCL was achieved, albeit with a factor of 20 reduction in flux density, which may not be a severe penalty at a synchrotron beamline. Previous efforts reported in the literature to increase the SCL that employed asymmetric crystal diffraction at grazing incidence are also discussed. A much reduced SCL is found presently in simulations wherein the same asymmetric crystal is set for grazing incidence instead of grazing exit. In addition, the present study is compared and contrasted with two other means of increasing the SCL. These are (i) focusing the beam onto an aperture to act as a secondary source, and (ii) allowing the beam to propagate in vacuum an additional distance along the beamline.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Co-Design of Free-Space Metasurface Optical Neuromorphic Classifiers for High Performance

Classification of features in a scene typically requires conversion of the incoming photonic field into the electronic domain. Recently, an alternative approach has emerged whereby passive structured materials can perform classification tasks by directly using free-space propagation and diffraction of light. In this manuscript, we present a theoretical and computational study of such systems and establish the basic features that govern their performance. We show that system architecture, material structure, and input light field are intertwined and need to be co-designed to maximize classification accuracy. Our simulations show that a single layer metasurface can achieve classification accuracy better than conventional linear classifiers, with an order of magnitude fewer diffractive features than previously reported. For a wavelength λ, single layer metasurfaces of size 100λ × 100λ with an aperture density λ –2 achieve ~96% testing accuracy on the MNIST data set, for an optimized distance ~100λ to the output plane. This is enabled by an intrinsic nonlinearity in photodetection, despite the use of linear optical metamaterials. Furthermore, we find that once the system is optimized, the number of diffractive features is the main determinant of classification performance. The slow asymptotic scaling with the number of apertures suggests a reason why such systems may benefit from multiple layer designs. Finally, we show a trade-off between the number of apertures and fabrication noise.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Neuromorphic Information Processing by Optical Media

Classification of features in a scene typically requires conversion of the incoming photonic field int the electronic domain. Recently, an alternative approach has emerged whereby passive structured materials can perform classification tasks by directly using free-space propagation and diffraction of light. In this manuscript, we present a theoretical and computational study of such systems and establish the basic features that govern their performance. We show that system architecture, material structure, and input light field are intertwined and need to be co-designed to maximize classification accuracy. Our simulations show that a single layer metasurface can achieve classification accuracy better than conventional linear classifiers, with an order of magnitude fewer diffractive features than previously reported. For a wavelength λ, single layer metasurfaces of size 100λ x 100λ with aperture density λ -2 achieve ~96% testing accuracy on the MNIST dataset, for an optimized distance ~100λ to the output plane. This is enabled by an intrinsic nonlinearity in photodetection, despite the use of linear optical metamaterials. Furthermore, we find that once the system is optimized, the number of diffractive features is the main determinant of classification performance. The slow asymptotic scaling with the number of apertures suggests a reason why such systems may benefit from multiple layer designs. Finally, we show a trade-off between the number of apertures and fabrication noise.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Evaluation of residual stresses in isothermal friction stir welded 304L stainless steel plates

Friction stir welding was performed on 304L SS plates in order to heal simulated cracks created by electrical discharge machining. Two different tool temperatures (825 and 725 °C) were chosen for this study. Both neutron diffraction and X-ray diffraction techniques were employed to evaluate the residual stresses along two orthogonal reference directions, longitudinal (syy) and transverse (sxx). The former technique was also used to measure residual stresses at various depths. It was found that, at 1 mm depth from the top surface inside the stir zone (SZ), the longitudinal component was tensile in nature while the transverse component was compressive. The nature and magnitude of the residual stress fields, and the position of the peak residual stresses were found to vary with the weld depth. The SZ of the 725 °C weld exhibited higher peak stress than 825 °C weld mainly due to a lack of stress relief at the lower temperature.

Friction stir welding, Steel↗
DOE OSTI2022

Computational approaches to model X-ray photon correlation spectroscopy from molecular dynamics

X-ray photon correlation spectroscopy (XPCS) allows for the resolution of dynamic processes within a material across a wide range of length and time scales. X-ray speckle visibility spectroscopy (XSVS) is a related method that uses a single diffraction pattern to probe ultrafast dynamics. Interpretation of the XPCS and XSVS data in terms of underlying physical processes is necessary to establish the connection between the macroscopic responses and the microstructural dynamics. To aid the interpretation of the XPCS and XSVS data, we present a computational framework to model these experiments by computing the X-ray scattering intensity directly from the atomic positions obtained from molecular dynamics simulations. We compare the efficiency and accuracy of two alternative computational methods: the direct method computing the intensity at each diffraction vector separately, and a method based on fast Fourier transform that computes the intensities at all diffraction vectors at once. Furthermore, the computed X-ray speckle patterns capture the density fluctuations over a range of length and time scales and are shown to reproduce the known properties and relations of experimental XPCS and XSVS for liquids.

36 MATERIALS SCIENCE↗