Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Correlation of Tensile Deformation-Induced Strain in HSLA Steel with Residual Stress Distribution

During service, due to the dynamic loading rates encountered, structural components experience varying levels of plastic deformation which leads to changes in the mechanical behavior of materials. The dynamic loading leads to non-homogenous plastic deformation which changes the residual stress distribution. In this study, the magnitude and distribution of residual stress in tensile tested specimens of high-strength low-alloy steel were investigated using x-ray diffraction technique, by varying the deformation rate. Tensile testing was performed at four different strain rates, and residual stress measurement was done along the length of the fractured specimens. Distribution of residual stress was observed all along the length of the specimens which is attributed to the varying levels of plastic deformation. Measured residual stresses are correlated with elastic strain and plastic strain obtained from the tensile tests. Consistent decrease in the magnitude of residual stress with an increase in plastic strain is observed with decreasing strain rate at the necking region. Specimen with lower yield strength experienced higher plastic strains, hence lower elastic residual stresses. The reasons for the observed distribution of residual stress are discussed with XRD peak broadening associated with plastic deformation.

36 MATERIALS SCIENCE↗

Optimization of structures undergoing harmonic or stochastic excitation

The optimal design was investigated of simple structures subjected to dynamic loads, with constraints on the structures' responses. Optimal designs were examined for one dimensional structures excited by harmonically oscillating loads, similar structures excited by white noise, and a wing in the presence of continuous atmospheric turbulence. The first has constraints on the maximum allowable stress while the last two place bounds on the probability of failure of the structure. Approximations were made to replace the time parameter with a frequency parameter. For the first problem, this involved the steady state response, and in the remaining cases, power spectral techniques were employed to find the root mean square values of the responses. Optimal solutions were found by using computer algorithms which combined finite elements methods with optimization techniques based on mathematical programming. It was found that the inertial loads for these dynamic problems result in optimal structures that are radically different from those obtained for structures loaded statically by forces of comparable magnitude.

Johnson, E. H.↗

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster decelerator subsystem drop test vehicle. Volume 3: Pylon load data method 1

The pylon loading at the drop test vehicle and wing interface attach points is presented. The loads shown are determined using a stiffness method, which assumes the side stiffness of the foreward hook guide to be one-fourth of the fore and aft stiffness of each drag pin. The net effect of this assumption is that the forward hook guide reacts approximately 85% of the drop test vehicle yawing moment. For a comparison of these loads to previous X-15 analysis design loadings, see Volume 1 of this document.

Quade, D. A.↗

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster deceleration subsystem drop test vehicle. Volume 4: Pylon load data

The pylon loading at the drop test vehicle and wing interface attack points is presented. The loads shown are determined using a stiffness method, which assumes the side stiffness of the forward hook guide and the fore and aft stiffness of each drag pin to be equal. The net effect of this assumption is that the forward hook guide reacts approximately 96% of the drop test vehicle yawing moment. For a comparison of these loads to previous X-15 analysis design loadings, see Volume 1 of this document.

Quade, D. A.↗

Graphene-Reinforced Aluminum Hybrid Foam: Response to High Strain Rate Deformation

The compressive deformation behavior of 0.5 wt.% graphene-reinforced aluminum-SiC hybrid composite foam under dynamic loading over strain rates of 500-2760 s{sup −1} was studied using a split-Hopkinson pressure bar unit. It was found that under the dynamic loading, the plateau stress and energy absorption of aluminum hybrid foam increased with strain rate. On the other hand, the densification strain did vary only marginally with strain rate. Further, it was noted that the foam with lower relative density was more sensitive to strain rate. The lighter foams exhibited higher plateau stress and energy absorption as compared to the heavier ones. The plateau stress and energy absorption were enhanced marginally with relative density. Present results showed that the plateau stress is sensitive to strain rate and less sensitive to relative density. The coefficient, in scaling relation to predict compressive plateau stress, was in the range of 0.2-0.5 for strain rates 500-2760 s{sup −1}.

36 MATERIALS SCIENCE↗

Dynamics of early planetary gear trains

A method to analyze the static and dynamic loads in a planetary gear train was developed. A variable-variable mesh stiffness (VVMS) model was used to simulate the external and internal spur gear mesh behavior, and an equivalent conventional gear train concept was adapted for the dynamic studies. The analysis can be applied either involute or noninvolute spur gearing. By utilizing the equivalent gear train concept, the developed method may be extended for use for all types of epicyclic gearing. The method is incorporated into a computer program so that the static and dynamic behavior of individual components can be examined. Items considered in the analysis are: (1) static and dynamic load sharing among the planets; (2) floating or fixed Sun gear; (3) actual tooth geometry, including errors and modifications; (4) positioning errors of the planet gears; (5) torque variations due to noninvolute gear action. A mathematical model comprised of power source, load, and planetary transmission is used to determine the instantaneous loads to which the components are subjected. It considers fluctuating output torque, elastic behavior in the system, and loss of contact between gear teeth. The dynamic model has nine degrees of freedom resulting in a set of simultaneous second order differential equations with time varying coefficients, which are solved numerically. The computer program was used to determine the effect of manufacturing errors, damping and component stiffness, and transmitted load on dynamic behavior. It is indicated that this methodology offers the designer/analyst a comprehensive tool with which planetary drives may be quickly and effectively evaluated.

August, R.↗

Calculation of reinforced-concrete frame strength under a simultaneous static cross section load and a column lateral impact

When designing buildings with reinforced concrete that are planned to resist dynamic loads it is necessary to calculate this structural behavior under operational static and emergency impact and blast loads. Calculations of the structures under shock-wave loads can be performed by solving dynamic equations that do not consider static loads. Due to this fact the calculation of reinforced concrete frame under a simultaneous static and dynamic load in full 3d settings becomes a very non trivial and resource consuming problem. This problem can be split into two tasks. The first one is a shock-wave problem that can be solved using software package RANET-3, which allows solving the problem using finite elements method adapted for dynamic task. This method calculates strain-stress state of the material and its dynamic destruction, which is considered as growth and consolidation of micro defects under loading. On the second step the results of the first step are taken as input parameters for quasi static calculation of simultaneous static and dynamic load using finite elements method in AMP Civil Engineering-11.

36 MATERIALS SCIENCE↗

O-ring gasket test fixture

An apparatus is presented for testing O-ring gaskets under a variety of temperature, pressure, and dynamic loading conditions. Specifically, this apparatus has the ability to simulate a dynamic loading condition where the sealing surface in contact with the O-ring moves both away from and axially along the face of the O-ring.

Turner, James Eric↗

The Feasibility of Adaptive Unstructured Computations On Petaflops Systems

This viewgraph presentation covers the advantages of mesh adaptation, unstructured grids, and dynamic load balancing. It illustrates parallel adaptive communications, and explains PLUM (Parallel dynamic load balancing for adaptive unstructured meshes), and PSAW (Proper Self Avoiding Walks).

Biswas, Rupak↗

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster decelerator subsystem drop test vehicle. Volume 2: Airplane flutter and load analysis results

The airplane flutter and maneuver-gust load analysis results obtained during B-52B drop test vehicle configuration (with fins) evaluation are presented. These data are presented as supplementary data to that given in Volume 1 of this document. A brief mathematical description of airspeed notation and gust load factor criteria are provided as a help to the user. References are defined which provide mathematical description of the airplane flutter and load analysis techniques. Air-speed-load factor diagrams are provided for the airplane weight configurations reanalyzed for finned drop test vehicle configuration.

Quade, D. A.↗

Effect of Solution Heating Rate on Quasi-static and Dynamic Mechanical Properties of Al-Mg-Si-Cu Alloy

The effect of solution heating rate on quasi-static and dynamic mechanical properties of Al-Mg-Si-Cu alloy in bake hardening state was investigated through mechanical properties, microstructure and fracture morphology characterization in the present study. The results show that solution heating rate has a strong influence on microstructure, quasi-static and dynamic mechanical properties. As solution heating rate rises, the grain microstructure transforms from the elongated grains to equiaxed grains and the fraction of low-angle grain boundaries (LAGBs) also decreases. Moreover, the equivalent average grain size first decreases, and then increases. The relationship between solution heating rate and mechanical property is monotonic, not depending on strain rate. As solution heating rate rises, the yield strength, ultimate tensile strength and elongation decrease. In contrast to quasi-static loading, dynamic loading always tends to improve strengths and elongation. In addition, compared with the quasi-static tensile specimens, the dynamic tensile specimens possess a larger number of dislocations. Regardless of strain rate and solution heating rate, all the tensile specimens exhibit the ductile fracture mode. As solution rate rises, the dimples decrease and become shallow gradually. The dimples in dynamic fracture zone are larger and deeper than those in the quasi-static fracture zone.

36 MATERIALS SCIENCE↗

Electrical conductivity of Sn at high pressure and temperature

To date, temperature and conductivity have many outstanding implications in extreme environments but are yet to be fully understood under high pressure and temperature dynamic conditions. Here, we introduce an approach to provide high quality electrical conductivity results under dynamic loading conditions. Emphasis is given to address the skin depth effect's influence in a dynamic loading experiment by using thin films. The thin film samples in this study were at least 100 times thinner than previous samples in dynamic electrical conductivity experiments, increasing the current density to its full potential across the sample's entire cross section. Consideration of the skin depth accounts for at minimum a 4× scaling factor to the final electrical conductivity result that has been neglected in previous dynamic electrical conductivity studies. We also obtained improved signal-to-noise ratio with custom diagnostics optimized for better electrical impedance matching. Furthermore, these considerations were applied to Sn to assess electrical conductivity at elevated pressure and temperature. The high signal-to-noise ratio with reduced skin depth influence results in Sn allowing observation of the conductivity changes related to solid-to-solid and solid-to-liquid phase transitions. Additionally, we calculate the Sn thermal conductivity using the Wiedemann-Franz law for our experiments and compare against thermal transport dependent temperature measurements from previous work.

36 MATERIALS SCIENCE↗

Solid face sheets enable lattice metamaterials to withstand high-amplitude impulsive loading without yielding

Owing to their ability to provide tunable mechanical responses, lattice materials are frequently studied to elucidate their response to static and dynamic loads. However, these roles are typically in opposition: static loads must be supported sufficiently far away from the onset of buckling or yielding, whereas dynamic loads are typically ameliorated by crushing of the lattice, which provides excellent energy-absorption due to the large plastic deformation accompanying densification. In contrast, this work considers the octet truss as an exemplar topology, in a structural role where it must simultaneously support static loads while enduring high-amplitude impulsive loads. This study focuses on the ability to withstand impulsive loads without yielding, an essential prerequisite to enduring dual loading. Computational studies using the ALE3D hydrocode were performed to examine the response of the octet truss under a short temporal width impulse shape associated with laser-driven shocks. A key finding was that covering the lattice with a solid face sheet and treating this face sheet thickness as a design variable allows the Taylor-like pulse to be attenuated prior to entering the weaker lattice, at the cost of added mass up front. Experimental validation was accomplished by laser-driven shock testing, using octet trusses printed out of Ti-5Al-5V-5Mo-3Cr. The results show that for a given quantity of mass, the attenuation is maximized when as much mass as possible is moved into the face sheet, leaving a more slender lattice structure. The effect of placing mass in the face sheet rather than lattice beams dominates the effect of relative density, to the point where a low-mass structure with most of the mass concentrated in the face sheet can outperform a high-mass structure with most of the mass in the lattice. Finally, by further understanding the propagation of short pulse width waves within under-dense structures, this study expand the domain of applicability of such structures, including lattice materials, to challenging dual-loading regimes spanning decades of strain rates.

36 MATERIALS SCIENCE↗

Structural load challenges during space shuttle development

The challenges that resulted from the unique configuration of the space shuttle and capabilities developed to meet these challenges are described. The methods and the organization that were developed to perform dynamic loads analyses on the space shuttle configuration and to assess dynamic data developed after design are discussed. Examples are presented from the dynamic loads analysis of the lift-off and maximum dynamic pressure portion of ascent. Also shown are orbital flight test results, for which selected predicted responses are compared to measured data for the lift-off and high-dynamic-pressure times of ascent. These results have generally verified the design analysis. However, subscale testing was found to be deficient in predicting full-scale results in two areas: the ignition overpressure at lift-off and the aerodynamics/plume interactions at high-q boost. In these areas, the results of the flight test program were accommodated with no impact to the vehicle design.

Mackey, A. C.↗

Design Space Exploration of Pericyclic Transmission with Counterbalance and Bearing Load Analysis

The pericyclic transmission provides the opportunity to vastly impact transmission design in rotorcraft due to its ability to provide exceedingly high reduction ratios in a single stage that would normally require multiple gear stages to produce. This could lead to lighter transmissions with fewer components, increased range, reliability, efficiency, speed and decreased cost to maintain. While many previous studies have focused upon the gearing within the pericyclic transmission, this work focused on what influences pericyclic geometry, and how changes in geometry impacts bearing loads. Specifically the loading of bearings that must deliver power from the input shaft to the nutating and rotating gears of the system were of primary concern. A comprehensive look at dynamic loads generated by nutating bodies was performed. Methods to address these dynamic loads via application of counterbalances and deviation from conventional pericyclic transmission designs were utilized to negate the dynamic moment of concern. Finally a static solver was used to determine the bearing loads with updated component geometries and mass moment of inertias that included the required counterbalances.

Pericyclic↗

Design Space Exploration of Pericyclic Transmission with Counterbalance and Bearing Load Analysis

The pericyclic transmission provides the opportunity to vastly impact transmission design in rotorcraft due to its ability to provide exceedingly high reduction ratios in a single stage that would normally require multiple gear stages to produce. This could lead to lighter transmissions with fewer components, increased range, reliability, efficiency, speed and decreased cost to maintain. While many previous studies have focused upon the gearing within the pericyclic transmission, this work focused on what influences pericyclic geometry, and how changes in geometry impacts bearing loads. Specifically the loading of bearings that must deliver power from the input shaft to the nutating and rotating gears of the system were of primary concern. A comprehensive look at dynamic loads generated by nutating bodies was performed. Methods to address these dynamic loads via application of counterbalances and deviation from conventional pericyclic transmission designs were utilized to negate the dynamic moment of concern. Finally a static solver was used to determine the bearing loads with updated component geometries and mass moment of inertias that included the required counterbalances.

Pericyclic↗

Design Space Exploration of Pericyclic Transmission

The pericyclic transmission provides the opportunity to vastly impact transmission design in rotorcraft due to its ability to provide exceedingly high reduction ratios in a single stage that would normally require multiple gear stages to produce. This could lead to lighter transmissions with fewer components, increased range, reliability, efficiency, speed and decreased cost to maintain. While many previous studies have focused upon the gearing within the pericyclic transmission, this work focused on what influences pericyclic geometry, and how changes in geometry impacts bearing loads. Specifically the loading of bearings that must deliver power from the input shaft to the nutating and rotating gears of the system were of primary concern. A comprehensive look at dynamic loads generated by nutating bodies was performed. Methods to address these dynamic loads via application of counterbalances and deviation from conventional pericyclic transmission designs were utilized to negate the dynamic moment of concern. Finally a static solver was used to determine the bearing loads with updated component geometries and mass moment of inertias that included the required counterbalances.

Nutational Gearing↗

Jet formation in cerium metal to examine material strength

Examining the evolution of material properties at extreme conditions advances our understanding of numerous high-pressure phenomena from natural events like meteorite impacts to general solid mechanics and fluid flow behavior. Recent advances in synchrotron diagnostics coupled with dynamic compression platforms have introduced new possibilities for examining in-situ, spatially resolved material response with nanosecond time resolution. In this work, we examined jet formation from a Richtmyer-Meshkov instability in cerium initially shocked into a transient, high-pressure phase, and then released to a low-pressure, higher-temperature state. Cerium's rich phase diagram allows us to study the yield stress following a shock induced solid-solid phase transition. X-ray imaging was used to obtain images of jet formation and evolution with 2–3 μm spatial resolution. From these images, an analytic method was used to estimate the post-shock yield stress, and these results were compared to continuum calculations that incorporated an experimentally validated equation-of-state (EOS) for cerium coupled with a deviatoric strength model. Reasonable agreement was observed between the calculations and the data illustrating the sensitivity of jet formation on the yield stress values. The data and analysis shown here provide insight into material strength during dynamic loading which is expected to aid in the development of strength aware multi-phase EOS required to predict the response of matter at extreme conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗