SEARCH · Search NASA

Results for “engine operability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS2005

Very Tough, Erosion-Resistant Turbine Airfoil Thermal Barrier Coatings Developed

Ceramic thermal barrier coatings (TBCs) are receiving increased attention for advanced gas turbine engine applications. These coatings are considered to be technologically important because of their ability to further increase engine operating temperatures and reduce cooling requirements, thus achieving higher engine efficiency, lower emissions, and increased performance goals. To take full advantage of the capabilities of these coatings, researchers need to use an aggressive design approach whenever possible--one that allows greater temperature reductions through the coating systems and less cooling air to the components. Advanced TBCs that have significantly lower thermal conductivity and better thermal stability than current coatings have been developed for future ultra-efficient, low-emission engine systems. Multicomponent-doped, defect-clustered TBCs have been shown to offer the low conductivity and high stability required for future high-temperature engine applications.

Zhu, Dong-Ming↗

NASA NTRS2010

Ares I-X: First Step in a New Era of Exploration

Since 2005, NASA's Constellation Program has been designing, building, and testing the next generation of launch and space vehicles to carry humans beyond low-Earth orbit (LEO). On October 28, 2009, the Ares Projects successfully launched the first suborbital development flight test of the Ares I crew launch vehicle, Ares I-X, from Kennedy Space Center (KSC). Although the final Constellation Program architecture is under review, data and lessons obtained from Ares I-X can be applied to any launch vehicle. This presentation will discuss the mission background and future impacts of the flight. Ares I is designed to carry up to four astronauts to the International Space Station (ISS). It also can be used with the Ares V cargo launch vehicle for a variety of missions beyond LEO. The Ares I-X development flight test was conceived in 2006 to acquire early engineering, operations, and environment data during liftoff, ascent, and first stage recovery. Engineers are using the test flight data to improve the Ares I design before its critical design review the final review before manufacturing of the flight vehicle begins. The Ares I-X flight test vehicle incorporated a mix of flight and mockup hardware, reflecting a similar length and mass to the operational vehicle. It was powered by a four-segment SRB from the Space Shuttle inventory, and was modified to include a fifth, spacer segment that made the booster approximately the same size as the five-segment SRB. The Ares I-X flight closely approximated flight conditions the Ares I will experience through Mach 4.5, performing a first stage separation at an altitude of 125,000 feet and reaching a maximum dynamic pressure ("Max Q") of approximately 850 pounds per square foot. The Ares I-X Mission Management Office (MMO) was organized functionally to address all the major test elements, including: first stage, avionics, and roll control (Marshall Space Flight Center); upper stage simulator (Glenn Research Center); crew module/launch abort system simulator (Langley Research Center); and ground systems and operations (KSC). Interfaces between vehicle elements and vehicle-ground elements, as well as environment analyses were performed by a systems engineering and integration team at Langley. Experience and lessons learned from these integrated product teams area are already being integrated into the Ares Projects to support the next generation of exploration launch vehicles.

Davis, Stephan R.↗

NASA NTRS1979

Multivariable control altitude demonstration on the F100 turbofan engine

The control system designed under the Multivariable Control Synthesis (MVCS) program for the F100 turbofan engine is described. The MVCS program, applied the linear quadratic regulator (LQR) synthesis methods in the design of a multivariable engine control system to obtain enhanced performance from cross-coupled controls, maximum use of engine variable geometry, and a systematic design procedure that can be applied efficiently to new engine systems. Basic components of the control system, a reference value generator for deriving a desired equilibrium state and an approximate control vector, a transition model to produce compatible reference point trajectories during gross transients, gain schedules for producing feedback terms appropriate to the flight condition, and integral switching logic to produce acceptable steady-state performance without engine operating limit exceedance are described and the details of the F100 implementation presented. The engine altitude test phase of the MVCS program, and engine responses in a variety of test operating points and power transitions are presented.

Lehtinen, B.↗

NASA NTRS1987

Overview of NASA Lewis Research Center free-piston Stirling engine technology activities applicable to space power systems

A brief overview is presented of the development and technological activities of the free-piston Stirling engine. The engine started as a small scale fractional horsepower engine which demonstrated basic engine operating principles and the advantages of being hermetically sealed, highly efficient, and simple. It eventually developed into the free piston Stirling engine driven heat pump, and then into the SP-100 Space Reactor Power Program from which came the Space Power Demonstrator Engine (SPDE). The SPDE successfully operated for over 300 hr and delivered 20 kW of PV power to an alternator plunger. The SPDE demonstrated that a dynamic power conversion system can, with proper design, be balanced; and the engine performed well with externally pumped hydrostatic gas bearings.

Slaby, Jack G.↗

NASA NTRS1972

Aircraft engine pollution reduction

Rudey, R. A.↗

NASA NTRS1973

Wind tunnel investigation of a large-scale upper surface blown-flap transport model having two engines

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blowing flap system that would augment lift. The model had a 25 deg swept wing of aspect ratio 7.89 and two turbofan engines with the engine centerline located at 0.256 of the wing semispan. The lift of the flap system was augmented by turbofan exhaust impingement on the Coanda surface. Results were obtained for several flap deflections and engine nozzle configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with two engines operating. Limited longitudinal and lateral data are presented with an engine out. In addition, limited exhaust and flap pressure data are presented.

Aoyagi, K.↗

NASA NTRS1972

Aircraft engine pollution reduction.

The effect of engine operation on the types and levels of the major aircraft engine pollutants is described and the major factors governing the formation of these pollutants during the burning of hydrocarbon fuel are discussed. Methods which are being explored to reduce these pollutants are discussed and their application to several experimental research programs are pointed out. Results showing significant reductions in the levels of carbon monoxide, unburned hydrocarbons, and oxides of nitrogen obtained from experimental combustion research programs are presented and discussed to point out potential application to aircraft engines. An experimental program designed to develop and demonstrate these and other advanced, low pollution combustor design methods is described. Results that have been obtained to date indicate considerable promise for reducing advanced engine exhaust pollutants to levels significantly below current engines.

Rudey, R. A.↗

NASA NTRS1978

Design and analysis of a scramjet engine

Design concepts defined for the cooled-structures assembly of a hydrogen fueled, regeneratively cooled, airframe-integrated Scramjet engine are considered. Engine subsystems, in particular, the fuel subsystem associated with the operating engine are included along with the engine mounting and the interfacing with the airplane. The engine structure and thermal protection system, including the fuel injection struts are emphasized.

Buchmann, O. A.↗

NASA NTRS1981

Structural dynamic analysis of the Space Shuttle Main Engine

This structural dynamic analysis supports development of the SSME by evaluating components subjected to critical dynamic loads, identifying significant parameters, and evaluating solution methods. Engine operating parameters at both rated and full power levels are considered. Detailed structural dynamic analyses of operationally critical and life limited components support the assessment of engine design modifications and environmental changes. Engine system test results are utilized to verify analytic model simulations. The SSME main chamber injector assembly is an assembly of 600 injector elements which are called LOX posts. The overall LOX post analysis procedure is shown.

Scott, L. P.↗

NASA NTRS1987

Progress toward an advanced condition monitoring system for reusable rocket engines

A new generation of advanced sensor technologies will allow the direct measurement of critical/degradable rocket engine components' health and the detection of degraded conditions before component deterioration affects engine performance, leading to substantial improvements in reusable engines' operation and maintenance. When combined with a computer-based engine condition-monitoring system, these sensors can furnish a continuously updated data base for the prediction of engine availability and advanced warning of emergent maintenance requirements. Attention is given to the case of a practical turbopump and combustion device diagnostic/prognostic health-monitoring system.

Maram, J.↗

NASA NTRS1956

Component Performance Investigation of J71 Experimental Turbine I : Over-all Performance with 97-percent-design Stator Areas

The over-all component performance characteristics of a J71 experimental three-stage turbine with 97 percent design stator areas were determined over a range of speed and pressure ratio at inlet-air conditions of approximately 35 inches of mercury absolute and 700 degrees R. The turbine break internal efficiency at design operating conditions was 0.877; the maximum efficiency of 0.886 occurred at a pressure ratio of 4.0 at 120 percent of design equivalent rotor speed. In general, the turbine yielded a wide range of efficient operation, permitting flexibility in the choice of different modes of engine operation. Limiting blade loading of the third rotor was approached but not obtained over the range of conditions investigated herein. At the design operating point, the turbine equivalent weight flow was approximately 105 percent of design. Choking of the third-rotor blades occurred at design speed and an over-all pressure ratio of 4.2.

Schum, Harold J↗

NASA NTRS1989

Moon base reactor system

The objective of our reactor design is to supply a lunar-based research facility with 20 MW(e). The fundamental layout of this lunar-based system includes the reactor, power conversion devices, and a radiator. The additional aim of this reactor is a longevity of 12 to 15 years. The reactor is a liquid metal fast breeder that has a breeding ratio very close to 1.0. The geometry of the core is cylindrical. The metallic fuel rods are of beryllium oxide enriched with varying degrees of uranium, with a beryllium core reflector. The liquid metal coolant chosen was natural lithium. After the liquid metal coolant leaves the reactor, it goes directly into the power conversion devices. The power conversion devices are Stirling engines. The heated coolant acts as a hot reservoir to the device. It then enters the radiator to be cooled and reenters the Stirling engine acting as a cold reservoir. The engines' operating fluid is helium, a highly conductive gas. These Stirling engines are hermetically sealed. Although natural lithium produces a lower breeding ratio, it does have a larger temperature range than sodium. It is also corrosive to steel. This is why the container material must be carefully chosen. One option is to use an expensive alloy of cerbium and zirconium. The radiator must be made of a highly conductive material whose melting point temperature is not exceeded in the reactor and whose structural strength can withstand meteor showers.

Chavez, H.↗

NASA NTRS2004

Hafnia-Based Materials Developed for Advanced Thermal/Environmental Barrier Coating Applications

Thermal and environmental barrier coatings (T/EBCs) will play a crucial role in advanced gas turbine engine systems because of their ability to significantly increase engine operating temperatures and reduce cooling requirements, and thus help achieve engine goals of low emissions and high efficiency. Under the NASA Ultra-Efficient Engine Technology (UEET) Project, advanced T/EBCs are being developed for low-emission SiC/SiC ceramic matrix composite (CMC) combustor applications by extending the CMC liner and vane temperature capability to 1650 C (3000 F) in oxidizing and water-vaporcontaining combustion environments. The coating system is required to have increased phase stability, lower lattice and radiation thermal conductivity, and improved sintering and thermal stress resistance under high-heat-flux and thermal-cycling engine conditions. Advanced heat-flux testing approaches (refs. 1 to 4) have been established at the NASA Glenn Research Center for 1650 C coating developments. The simulated combustion water-vapor environment is also being incorporated into the heat-flux test capabilities (ref. 3).

Zhu, Dongming↗

NASA NTRS1946

Correlation of Mixture Temperature Data Obtained from Bare Intake-manifold Thermocouples

A relatively simple equation has been found to express with fair accuracy, variation in manifold-charge temperature with charge in engine operating conditions. This equation and associated curves have been checked by multi cylinder-engine data, both test stand and flight, over a wide range of operating conditions. Average mixture temperatures, predicted by the equations of this report, agree reasonably well with results within the same range of carburetor-air temperatures from laboratories and test stands other than the NACA.

ENGINES-PRATT & WHITNEY R-1830-75 (AMER )↗

NASA NTRS1980

Engine identification for adaptive control

An attempt to obtain a dynamic model for a turbofan gas turbine engine for the purpose of adaptive control is described. The requirements for adaptive control indicate that a dynamic model should be identified from data sampled during engine operation. The dynamic model identified was of the form of linear differential equations with time varying coefficients. A turbine engine is, however, a highly nonlinear system, so the identified model would be valid only over a small area near the operating point, thus requiring frequent updating of the coefficients in the model. Therefore it is necessary that the identifier use only recent information to perform its function. The identifier selected minimized the square of the equation errors. Known linear systems were used to test the characteristics of the identifier. It was found that the performance was dependent on the number of data points used in the computations and upon the time interval over which the data points were obtained. Preliminary results using an engine deck for the quiet, clean, shorthaul experimental engine indicate that the identified model predicts the engine motion well when there is sufficient dynamic information, that is when the engine is in transient operation.

Leonard, R. G.↗

NASA NTRSDate not supplied

Effects of Varying the Heat Transfer Coefficient on Engine Performance

A physics-based Nuclear Thermal Propulsion (NTP) Testing Reference Design (TRD) power balance model was coded in Simulink to investigate engine performance for various design and parameter modifications. Since the primary mode of heat transfer in NTP engines is convective, the convective heat transfer coefficient (HTC) is a key parameter that requires accurate representation. The industry standard Westinghouse correlation has an uncertainty of ±20% which was investigated in this study. The results showed that a 20% decrease in the HTC led to a 4.14% increase in maximum fuel temperature while a 20% decrease in the HTC led to a 1.81% decrease in maximum fuel temperature suggesting that narrowing the uncertainty of this correlation through experimental work would be a critical step in the development of NTP engines. Furthermore, a maximum fuel temperature relationship with specific impulse was developed for the TRD engine which showed potential engine operation between specific impulse values of 715 and 900 seconds with minimal changes to the engine design. This graph could be useful for high level vehicle performance estimations for fuel types with different maximum operating temperatures.

Heat Transfer Coefficient↗

NASA NTRSDate not supplied

Effects of Heat Transfer Coefficient Variation on Nuclear Thermal Propulsion Engine Performance

Heat Transfer Coefficient↗

NASA NTRS1968

Development of detonation reaction engine

Reaction engine operates on the principle of a controlled condensed detonation. In this engine the gas products that are expelled from the engine to produce thrust are generated by the condensed detonation reaction. The engine is constructed of two basic sections consisting of a detonation wave generator section and a condensed detonation reaction section.

Lange, O. H.↗